Packaging Information
Vishay Semiconductors
D2PAK
CARRIER TAPE FOR TAPE AND REEL LEFT in millimeters
Carrier tape (130 meter long per reel)
C7
Ø 1.55 ± 0.05
P2
2.0 ± 0.1
Y
0.40 ± 0.05
C6
P0
4.0 ± 0.1
1.75 ± 0.1
Ø 1.6 ± 0.1
C4
1.57 ± 0.1
2.17 ± 0.1
0.12 MAX.
F ± 0.1
C5
C2
CL
W ± 0.3
B2 ± 0.1
R 0.3
typical
Y
P1 ± 0.1
A0 ± 0.1
1.20
C1
K0 ± 0.1
Reel
Unreeling direction
30
B0 ± 0.1
C3
Section Y - Y
114
Ø 72
Ø 560
Single
winded
Level
winded
NUMBER
PACKAGE
A0
B0
B2
K0
F
P1
W
93-0194-01
D2PAK
10.80
16.00
10.35
4.90
11.50
16.00
24.00
REEL DIAMETER QUANTITY PER REEL
330
800
Notes
MATERIAL
• Free of heat marks
1. General
• No sharp edges allowed
• ST : Statistical, Cpk  1.33
• No deformities allowed in wall cavity
• 10 sprocket hole pitch cumulative tolerance ± 0.02 mm
• Holes, edges and cavities must be free of burrs  0.060 mm (burrs
• Camber not to exceed 1 mm in 250 mm
• A0 and B0 measured on a plane 0.3 mm above the bottom of the
pocket
• K0 measured from a plane on the inside bottom of the pocket to
the top surface of the carrier
• Pocket position relative to sprocket hole measured as true
position of pocket, not pocket hole
• Measured from centerline of sprocket hole to centerline of pocket
• Must also meet requirements of EIA standard #EIA-481A taping
of surface mount components for automatic placement
2. Specification
shall not come off the tape)
PACKAGING
1. General
• Each box must be identified with Vishay part number 93-0194-x
• Box should be free of foreign particles
• Product must be stored at room temperature and clean
environment
• Certificate of analysis is required per every lot number
2. Material
• Conductive black styrenic alloy
• Poliestyrene
• Surface resistivity of molded material must measure  106 /SQ
measured in accordance to procedure given in ASTM D-257 and
ASTM D-991
Document Number: 95032
Revision: 09-May-11
For technical questions within your region, please contact one of the following:
www.vishay.com
DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
1
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging Information
D2PAK
Vishay Semiconductors
CARRIER TAPE FOR TAPE AND REEL RIGHT in millimeters
Carrier tape (130 meter long per reel)
C6
Ø 1.55 ± 0.05
P2
2.0 ± 0.1
Y
K0 ± 0.1
C7
P0
4.0 ± 0.1
1.20
1.75 ± 0.1
C4
Ø 1.6 ± 0.1
Y
1.57 ± 0.1
2.17 ± 0.1
F ± 0.1
R 0.3
typical
A0 ± 0.1
P1 ± 0.1
C3
B2 ± 0.1
C5
CL
C2
B0 ± 0.1
W ± 0.3
0.12 MAX.
C1
0.40 ± 0.05
Reel
Unreeling direction
30
Section Y - Y
114
Ø 72
Ø 560
Single
winded
Level
winded
NUMBER
PACKAGE
A0
B0
B2
K0
F
P1
W
93-0195-01
D2PAK
10.80
16.00
10.35
4.90
11.50
16.00
24.00
REEL DIAMETER QUANTITY PER REEL
330
800
Notes
MATERIAL
PACKAGING
1. General
1. General
• ST : Statistical, Cpk  1.33
• 10 sprocket hole pitch cumulative tolerance ± 0.02 mm
• Each box must be identified with Vishay part number 93-0195-x
• Camber not to exceed 1 mm in 250 mm
• Product must be stored at room temperature and clean
• A0 and B0 measured on a plane 0.3 mm above the bottom of the
pocket
• K0 measured from a plane on the inside bottom of the pocket to
the top surface of the carrier
• Pocket position relative to sprocket hole measured as true
position of pocket, not pocket hole
• Box should be free of foreign particles
environment
• Certificate of analysis is required per every lot number
2. Material
• Conductive black styrenic alloy
• Measured from centerline of sprocket hole to centerline of pocket
• Must also meet requirements of EIA standard #EIA-481A taping
of surface mount components for automatic placement
2. Specification
• Poliestyrene
• Surface resistivity of molded material must measure  106 /SQ
measured in accordance to procedure given in ASTM D-257 and
ASTM D-991
• Free of heat marks
• No sharp edges allowed
• No deformities allowed in wall cavity
• Holes, edges and cavities must be free of burrs  0.060 mm (burrs
shall not come off the tape)
www.vishay.com
2
For technical questions within your region, please contact one of the following:
Document Number: 95032
DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
Revision: 09-May-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Packaging Information
D2PAK
Vishay Semiconductors
COVER TAPE FOR CARRIER TAPE in millimeters
W
Y
X
ST
Y
Ø 76.5 ± 1.0
X
Section X - X
Antistatic layer
Pet layer
ST 0.055 ± 0.005
Olefin layer
Sealant layer
Section Y - Y
VERSION
NUMBER
APPLICATION
W
CARRIER TAPE WIDTH
MATERIAL
01
92-5210-14
D2PAK
21.3 ± 0.1
24
Antistatic/treated/transparent/polyester
Notes
MATERIAL
• No sharp edges allowed
1. General
• No burrs allowed
• ST : Cpk  1.33
2. Specification
• Thickness: 0.052 ± 0.005
• Length: 500 m
PACKAGING
• Tensile strength: 6.00 kg/mm SQ
1. General
• Elongation: > 100 %
• Each box must be identified with Vishay part number 92-5210-x
•Surface resistivity: 10E11 /SQ max. both sides (antistatic)
• Box should be free of foreign particles
• Peel strength conforms to IRMX specification P01-0074
• POS test range not to exceed 35 grf.
Data included on C of C of every lot
• Curl 4.5 mm max.
Sample length 200 mm
Frequency 5 times
• Inspection date < one year
• Luminous transmittance: 89.8 %
• Must also meet all requirements of EIA-standard #EIA-481C,
taping of surface mount components for automatic placement
• Free of heat marks
Document Number: 95032
Revision: 09-May-11
For technical questions within your region, please contact one of the following:
www.vishay.com
DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
3
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000