Issue Date:
2008-10-15
Amendment 1
2009-10-27
Page 1 of 3
Report Reference #
E185611-A1-UL-1
COVER PAGE FOR TEST REPORT
Product Category:
Product Category CCN:
Test Procedure:
Product:
Model/Type Reference:
Rating(s):
Process Control Equipment, Electrical
QUYX
Listing
Process control
Temperature controllers, RM Series, Models RM followed by additional letters
or numbers defining up to four modules cards of input, communications and/or
output.
Module card options:
Watlow PCB#
Description
Number Allowed
A007-2828-0000
Power Supply Board
Always 1
A007-2829-0000
Supervisor Board
Always 1
A007-2835-0000
Backplane
Always 1
A007-2841-0000
Display Module
Always 1
A007-2842-0000
Riser Module
Always 1
A007-2775-0000
PID control card
Up to 4
A007-2776-0000
Process control cardUp to 4
A007-2777-0000
No-arc board
Up to 4
A007-2778-0000
RS485 Communications
Up to 1
A007-2779-0000
Ethernet Communications
Up to 1
A007-2814-0001
Devicenet Communications
Up to 1
A007-2815-0000
Profibus Communications
Up to 1
A007-2836-0000
USB, SD data log card
Up to 1
A007-2830-0000
Hex Digital I/O
Up to 4
A007-2831-0000
Dual 10A SSR output
Up to 2
A007-2832-0000
Quad Relay output
Up to 3
A007-2833-0000
Quad current sense input
Up to 4
A007-2833-0000
Quad Sensor Input 4
Universal inputs
Up to 4
INPUTS:
Type
Input Rating
Terminals
Power supply: 24-28 V ac/dc, 50/60 Hz; RM any letter other than A, 7 W or 14
VA max; RMA 4 W or 9 VA max.; 98-99
Digital Inputs - (Up to 6 per card, DC Voltage or Contact Closure)
36 V
dc, 3 mA max, SELV, Limited Energy B7, D7, D8, D9, D10, D11, D12, Z7.
Input #, Thermocouple, SELV, Limited Energy
R#-S#
Input #, RTD
SELV, Limited Energy
R#-S#; R#-S#-T#
Input #, Process
SELV, Limited Energy
R#-S#, S#-T#
Input #, Potentiometer
SELV, Limited Energy
R#-S#
Up to four inputs are available on each module.
Input # = Terminal #
COMMUNICATION:
Type
Rating
Terminal
Standard EIA-485 SELV, Limited Energy
CD, CE, CF
Modbus RTU or Standard EIA-485
SELV, Limited Energy
Copyright © 2009
CA,
Issue Date:
2008-10-15
Amendment 1
2009-10-27
Page 2 of 3
Report Reference #
E185611-A1-UL-1
CB, CC
EIA-232/485 Modbus RTU
SELV, Limited Energy
Communications
CA, CB, CC, C2, C3, C5
Devicenet SELV, Limited Energy
V+, CH, SH, CL, VEthernet/IP
SELV, Limited Energy
E1-E8
USB
SELV, Limited Energy
USB connector
Profibus SELV, Limited Energy
VP, B, A, DG, trB, B, A, trA
OUTPUTS:
Type
Rating
Terminal
Digital Outputs (Up to 6 per card, DC Voltage or Contact Closure) Source 20 or
12 V user selectable, 40 or 80 mA max. for all 6 outputs combined or Sink 32 V,
1.5 A per output or total 8 A max. for all 6 outputs, SELV, Limited Energy B7,
D7, D8, D9, D10, D11, D12, Z7.
Output #, DC/Open Collector, source 32 V dc, 30 mA max, or Sink 100 mA
max. SELV, Limited Energy W#-X#-Y#
Output #, Mechanical Relay (Form C)
240 V ac, 5 A resistive 30 V dc, 5A
resistive 124/240 @ 125 VA 24 V ac @ 25 VA, resistive, 100 K cycles J#-K#-L#
Output #, Mechanical Relay No-Arc(Form A), 240 V ac, 15 A resistive 500 K
cycles
L#-K#
Output #, Universal Process
0-20 mA, 0-10 V dc, SELV, Limited Energy
Output #, SSR, Form A
pilot duty L#-K#
20-264 V ac, 0.5 A resistive 120/240 V @ 20 VA
Output # Dual SSR Module, Form A, 20-264 Vac, 10 A resistive L#K#
Output # = Terminal #
Standards:
Temperature -18 to 65°C
UL 61010-1, 2nd Edition, 2005-07-22 (Electrical Equipment for Measurement,
Control, and Laboratory Use; Part 1: General Requirements)
Applicant Name and
Address:
WATLOW WINONA INC
1241 BUNDY BLVD
PO BOX 5580
WINONA MN 55987
UNITED STATES
This Report includes the following parts, in addition to this cover page:
1. Specific Technical Criteria
2. Critical Components
3. Test Results
4. Enclosures
Copyright © 2009
Issue Date:
2008-10-15
Amendment 1
2009-10-27
Page 3 of 3
Report Reference #
E185611-A1-UL-1
This is to certify that representative samples of the products covered by this Test Report have been investigated in accordance with the
above referenced Standards. The products have been found to comply with the requirements covering the category and the products are
judged to be eligible for Follow-Up Service under the indicated Test Procedure. The manufacturer is authorized to use the UL Mark on
such products which comply with this Test Report and any other applicable requirements of Underwriters Laboratories Inc. ('UL') in
accordance with the Follow-Up Service Agreement. Only those products which properly bear the UL Mark are considered as being
covered by UL's Follow-Up Service under the indicated Test Procedure.
The applicant is authorized to reproduce the referenced Test Report provided it is reproduced in its entirety.
Any information and documentation provided to you involving UL Mark services are provided on behalf of Underwriters Laboratories
Inc(ULI) or any authorized license of ULI.
Test Report By:
Reviewed By:
Marcin Zurek
Associate Project Engineer
UL International Polska Sp. z o.o.
Ivy Maria Puthenveetil
Project Engineer
Underwriters Laboratories Inc.
Copyright © 2009