Rotary Numbering Machines

advertisement
Rotary
Numbering Machines
Numbering Machines
Mechanical
Rotary Numbering Machines
Straight or convex, 7 or 9 digits in
engravings 3/16“ Gothic, 1/4“ Gothic,
Farrington 7B, engravings 115, 116, etc.
Rotary numbering machines for
encoding
E.g. numbering of cheques from 7 to
43 digits with the MICR engravings
E13B and CMC-7 as well as the OCR
engraving
OCR-A1, A3 and A4 and
OCR-B1, B3 and B4.
Numbering of lottery tickets
Special engravings with lateral font,
below or inside.
Barcode numbering machines
In all requested designs, e.g. for
documents of DHL, Federal Express,
EMS, ATB-1, etc.
Special designs
With special sequences, skipping,
repeating, with pre-inking device, with
lockout feature for the non-automatic
wheels, front gib locking system,
modulus systems weighted and nonweighted, etc.
Accessories
Cams, mounting rings, strike-in blocks,
etc.
Electronic
Rotary Numbering Machines
LEIBINGER PC LEN
Electronic Random Numbering
With the LEIBINGER PC LEN it is
possible to control a maximum of 12
figure wheels electronically. The control
is done via stepping motors.
This full electronic numbering system
combines the following advantages:
∙∙ The numbering machines are a two-unit
construction. The mechanical unit with
figure wheels can be seperated from
the electronic unit. It can be cleaned
and maintained like a conventional
mechanical numbering machine.
∙∙ No manual setting of starting numbers
is required; a manual re-setting after a
press stop is not necessary.
∙∙ All sequences and check digit sytems
are possible.
This system is mainly used:
∙∙ On single-note banknote-presses
∙∙ Numbering of securits documents
like passports etc.
LEIBINGER Full Monitoring System
The LEIBINGER Full Monitoring System
combines the advantages of a purely
mechanically
operated
numbering
machine and a 100% electronic control.
Concept
Basis of the numbering machines in
such a numbering system is a two-unitconstruction. The upper unit, containing
the mechanical moving parts, can be
seperated easily from the unit containing
the electronic parts by loosening only
two screws. This concept has a lot of
advantages in terms of handling and
maintenance:
The mechanical unit with the moving
parts can be handled, cleaned and
maintained in the same way as
conventional mechanical numbering
machines.
The second unit, containing the sensor
electronics, stays on the press as no
cleanning and regular maintenance is
required. After re-connecting the upper
mechanical unit no new positioning is
required, all machines are in the proper
location (no move of lower adaptor
unit).
The numbering machines are equipped
with a pre-inking system.
The non-automatic wheels are locked
by means of a spring loaded pin; to
turn the wheels one has to push the pin,
after releasing it again the wheels are
automatically locked.
Additonal electronic parts are available
upon request
5a
Retaining Pawl Unit
5b Retaining Pawl Tens
Retaining Pawl
Set
5
5c Retaining Pawl Pin
(Pos. 5a, 5b, 5c)
5d Retaining Pawl Springs
6
Gib Lock Screw
Case
8
Base Locating Screw
Gib 10
Gib Holding
Screws
9
Unit Wheel
1
Tube Shaft
3
7
Tube Shaft Set Screw
1
Tens Wheels
7
(Position has to be added)
26
Spring return arm
4
Operation arm
2
Swing assembly
E Ring 4a
Actuating Pawl 2a
Swing 2b
Actuating Pawl
2c
Spring
Actuating Pawl
2d
Shaft
Spare parts numbering machine straight
Ordering directions:
For special numbering machines with special functions like preinking, modulus,
electronic monitoring, please advice the serial number of the numbering
machine.
Retaining Pawl
Set
5
5a
Retaining Pawl Unit
5b
Retaining Pawl Tens
5c
Retaining Pawl Pin
5d
Retaining Pawl Springs
6
Case
(Pos. 5a, 5b, 5c)
Gib Lock Screw
Gib
8
10
Base Locating Screw
Gib Holding
Screws
9
Unit Wheel
1
7
Tube Shaft Set Screw
1
Tens Wheels
7
(Position has to be added)
Tube Shaft
3
E Ring
4a
Actuating Pawl
2a
Swing
2b
Actuating Pawl
Spring
2c
Actuating Pawl
Shaft
2d
Spare parts numbering machine convex
Ordering directions:
For special numbering machines with special functions like preinking, modulus,
electronic monitoring, please advice the serial number of the numbering
machine.
4
Operation arm
25
Spring return arm
2
Swing assembly
Accessories
Cams
∙∙ solid
∙∙ split
∙∙ with window
∙∙ with segment and pneumatic cylinder
Mounting ring split
LEIBINGER Service Toolkit
For all service, maintenance, and mounting
procedure to LEIBINGER precision-rotarynumbering machines.
Local distributor contact:
Paul Leibinger GmbH & Co. KG
Daimlerstr. 14
78532 Tuttlingen / Germany
Phone+49 (0) 74 61 / 92 86 - 0
Fax +49 (0) 74 61 / 92 86 - 199
www.leibinger-group.com
info@leibinger-group.com
Download