The Perfect Draft BBQ Blower Manual The Perfect Draft BBQ Blower.com 1 Table of Contents 1. What’s Included with your BBQ Blower and fully charging the unit before using 2. Overview of the Operation of the BBQ Blower 3. Installation of the Perfect Draft BBQ Blower with Safely Hook 4. Operating your BBQ Blower 5. Controlling the BBQ Blower in Automatic mode 6. Controlling the BBQ Blower in Manual mode 7. Temperature probe description and placement 8. Care and maintenance of The Perfect Draft BBQ Blower 9. Troubleshooting the unit CAUTION: If your BBQ Pit temperature is over 400 degrees ‘’ Remove The BBQ BLOWER” Once the temperature is below 400 degrees reconnect the BBQ Blower. This can Damage the Blower. 2 1. What’s included with your BBQ Blower 1. The Perfect Draft BBQ Blower with 20 High Temperature Magnets 2. 12-volt Battery Charger 3. 6 foot Thermo probe 4. 2” Safety hook 5. (On board) Rechargeable 12-volt Samsung Battery 6. 120mm variable speed Fan Fully Charge the on board 12-volt battery before using the unit 2. Overview of the Operation of the BBQ Blower The Perfect Draft BBQ Blower is a powered draft system that controls the temperature of your BBQ pit using state-of-the-art technology, which incorporates a temperature probe and a variable speed fan for premium airflow control. The BBQ Blower system is equipped with an automatic control setting or a manual control setting, enabling you to maximize temperature efficiency and time management. While in automatic control mode, the built in circuit board is designed to utilize the temperature probe to send a constant heat signal to the BBQ Blower fan, regulating a precise flow of air into the firebox to achieve the desired temperature set point. NOTE: If the temperature in the BBQ Pit continues to rise the BBQ Blower Fan will not come on, you should CLOSE OFF on your Stack Damper to lower the temperature into a proper range and let the BBQ Blower fan will cycle on/off to regulate your pit temperature. If you want to take control, the manual control settings allow you to monitor your local temperature gauge and you can adjust the Fan speed manually to regulate the temperature in your smoker. CAUTION: If your BBQ Pit temperature is over 400 degrees ‘’ Remove The BBQ BLOWER” Once the temperature is below 400 degrees reconnect the BBQ Blower. This can Damage the Blower. 3 3. Installation of the Perfect Draft BBQ Blower with Safely Hook The BBQ Blower has a slotted attachment on the front of the Blower. This attachment is used to slide over the included safety hook to prevent the blower from falling in the event of an unforeseen incident, causing the blower to be damaged and voiding the warranty. IMPORTANT – Please ensure your BBQ Pit is NOT in use when attempting to install safety hook and temperature probe. To properly install the safety hook, first remove the attached bolt and nut from the safety hook. 2. Every firebox is designed different so you need to locate the best place to attach the safety hook over the open area of your firebox register. Once you have located the proper location for the safety hook. Mark the spot using the hook for your template drill a ¼ hole and secure the hook using the bolt and wing nut. Now you can attach the BBQ Blower on the hook. And now you’re ready to start using your Blower. Before using your BBQ Blower made sure the battery is fully charged The front metal plate can withstand high temperatures, but it is important not to leave the Blower connect continuously for over 17hrs. Straight, The radiant heat could possibly damage the front Plastic parts of the BBQ Blower. We have an adaptor that you can purchase to resolve this issue. 4 4. Operating your BBQ Blower Adjusting your stack damper slightly closed is important when using the Blower When starting your BBQ fire add your desired charcoal and wood and light it. Next open the stack damper wide open to 100%. You can attach your BBQ Blower and put the switch on manual operation to help regulate the airflow to get the fire going. Once you have a good fire, start adjusting your damper slightly towards the closed position until your temperature starts to lower. Note: Do not closed your stack damper completely Attach the Perfect Draft BBQ Blower Open the stack damper 100% when starting your fire Close stack damper 50% - 60% for medium to high temperature smoking Close stack damper 75% - 85% for low temperature smoking 5 5. Controlling the BBQ Blower in Automatic mode 2. Automatic Switch is ON In the Down Position 1. Power Switch is ON in the down position Plug the charger in here to recharge the battery. The indicator light on the head of the charger will show green when fully charged. 4. 3. Connect Temperature Probe Here 1. Turn the power button on. 2. Turn the Auto Control switch on 3. Connect the 3.5mm temperature plug into the control panel 4. Set the desired temperature using the temperature knob 5. Throttle the stack damper cover 75% - 85% closed 6. Let the Perfect Draft BBQ Blower do its job 6 6. Controlling the BBQ Blower in Manual mode 2. Leave OFF For Manual Control The up Position is off 1. Power Switch is on in the down Position 3. FAN Speed Switch Plug in Battery to Charge it 1. Turn the power button on 2. Leave the auto control in off position 3. Adjust the Variable Speed Fan Knob accordingly to maintain your desire Temperature 4. Close the stack damper cover 75% - 85% closed 5. Let the Perfect Draft BBQ Blower 7 7. Temperature probe description and placement The temperature probe is made of braided stainless but avoid exposing the thermocouple wires to direct flame this can damage the probe. You can order replacement probes from www.bbqblowers.com. Your BBQ Blower temperature probe should always be placed so that it is not in a direct line with the fire. For best practice, chose a location near the top of your BBQ pit close to the existing temperature gauge. Using a 1/8” drill bit, drill a hole in the desired location on your BBQ pit. NOTE – Simply placing the temperature probe under the lid of the BBQ pit while is use may cause damage to the wires resulting in faulty temperature readings and voiding the warranty. The Perfect Draft BBQ Blower.com 8 8. Care and maintenance of The Perfect Draft BBQ Blower If your BBQ pit cooking temperature exceeds 400 degrees you should remove The Perfect Draft BBQ Blower from the firebox. Excessive high temperatures will shut the fan off and the unit’s outer shell could possibly be damaged from the excessive heat. When using The Perfect Draft BBQ Blower to cook at high temperatures you should remove the Blower. The onboard battery can stay charged for 17 hours run time when the fan is cycling on and off at normal conditions. Make sure to turn The Perfect Draft BBQ Blower off when you are finished cooking to prevent the battery usage. Caution: The unit electronics are not waterproof so cover it up when it raining outdoors. The Perfect Draft BBQ Blower’s outer shell can be cleaned with a rag with mild detergent. The probe can be cleaned using any household stainless steel cleaner. 9. Troubleshooting the unit The BBQ Blower will not power up Plug the charger into the Blower control panel. If the indicator light on the charger is red, the blower will need to be fully charged The switch could have malfunctioned, Email us at bbqblowerservice@gmail.com for Repair or replacement. The Automatic Switch doesn’t control the Fan Speed The Power Switch doesn’t energize the unit. The manual Switch control the Fan Speed The Thermocouple isn’t communicating Possible break in the Thermocouple with the Circuit Board cable or loose connection. Order a replacement cable from our website. PLEASE REGISTER YOUR BBQ BLOWER AT OUR WEBSITE ONE YEAR LIMITED WARRANTY, DOWNLOAD WARRANTY INFORMATION AT WWW.BBQBLOWER.COM 9 10