GENUINE
FOG LIGHT BEZEL
INSTALLATION INSTRUCTIONS
Thank you for purchasing a genuine Mazda accessory.
Before removal and installation, be sure to thoroughly read these instructions.
Please read the contents of this booklet in order to properly install and use the fog
light bezel. Your safety depends on it.
Keep these instructions with your vehicle records for future reference.
WARNING
• There are several
WARNING and
CAUTION sections in this booklet concerning
safety when installing or removing the rear spoiler. Always read and follow them in
order to prevent injuries, accidents, and possible damage to the vehicle.
WARNING: Indicates a situation in which serious injury or death could result if
the warning is ignored.
CAUTION : Indicates a situation in which bodily injury or damage to the vehicle
could result if the caution is ignored.
• Do not modify the fog light bezel.
• Do not install the fog light bezel in any way other than described in the following
instructions.
• If in any doubt, please ask your Mazda dealer to install the accessory in order to
prevent errors in installation.
• If you have any questions about the use of the accessory, ask your Mazda dealer for
proper advice before using it.
• Mazda and its suppliers are not responsible for injuries, accidents, and damage to
persons and property that arise from the failure of the dealer or installer to follow these
instructions.
• To ensure safety and reliability of the work, installation, removal and disposal work
must carried out by an Authorized Mazda Dealership.
• Be careful not to lose removed parts, and be sure that they are kept free from
scratches, grease or other dirt.
PART NAME:
FOG LIGHT BEZEL
PART NUMBER: N121 V7 247F
N123 V7 247F
VEHICLE:
MX-5
NOTE
To the dealer
• Please turn over these instructions to the customer after installation.
To the customer
• Keep these instructions after installation. The instructions may be necessary
for installing other optional parts or removal of this accessory.
• Should the vehicle or this accessory be resold, always leave these instructions
with it for the next owner.
0000 00 000
─１─
１．PARTS
Parts list
NOTE
• Before installation, verify that the kit includes all the following parts and that they are free of dirt, scratches,
or damage.
Fog light bezel（Silver） N121 V7 247F
Part
Fog light bezel（Silver）
Part name
Qty
ＲＨ（N121 V7 248）
ＬＨ（N121 V7 249）
1ea.
Installation instructions
Fog light bezel（Black） N123 V7 247F
Part
Fog light bezel（Black）
Installation instructions
1
Part name
Qty
ＲＨ（NE55 50 C11）
ＬＨ（NE55 50 C21）
1ea.
1
CAUTION
• Fog lights are not included in this kit. For vehicles without fog lights, it is necessary to purchase them
separately.
（Separate purchase）
GENUINE FOG LIGHT
N121 V7 220 ／ N122 V7 220 ／ N123 V7 220
（Clear）
（Blue）
（Multi coating）
Installation view
Fog light bezel
─２─
２．REQUIRED TOOLS
☆Screwdriver (Phillips)
☆Torque wrench
☆Fastener remover
☆Round file
３．BEFORE INSTALLATION
WARNING
When the negative battery cable is
connected during operation, it may
cause electric shock or other
personal injuries. Disconnect the
negative battery cable before
removal/installation.
Do not pull the harness
With excessive force. Doing so
can cause a breakage or a
short-related accident, as well as
an electrical short or fire.
When connecting/disconnecting
connectors, grasp the
connectors, not the wires.
Otherwise a short, an accident
from poor contact or fire may
occur.
Use the most appropriate
(size, use) tool for each task and
perform the may be damaged.
Place the removed parts and kit
accessories on a protective sheet
to prevent scratches.
CAUTION
Be sure to cover the vehicle body
With protectors or mats to prevent
stains, scratches and damage when
removing/installing the vehicle parts
WARNING
• Park the vehicle on a flat, level surface, set the selector lever to P (AT vehicles) or the shift lever to 1st or R
(MT vehicles), apply the parking brake and block the wheels so that the vehicle does not move during
CAUTION
• When the negative battery cable is removed, the clock, radio, trip, meters and other memories will be
erased. Before performing work, record the content of the memory.
• Always tighten bolts, nuts and screws with a torque wrench, and tighten to the specified torque. If tightened
outside the specified torque, it could result in poor fit, damage to installed parts or other damage.
NOTE
• Refer to the Workshop Manual for removal and installation of vehicle parts.
Not following the procedures for removal/installation in the Workshop Manual could result in an accident or
vehicle malfunction.
─３─
４．PART REMOVAL
Bolt B
Nut
B
Front bumper removal
１． Remove screws A (10) and fasteners A (10).
２． Remove the cover, and then remove bolts A (2).
３． Peel back the mudguard, and remove the nuts (4) and bolts B
(2).
４． Remove bolts C (8), then pull the front cover outward to
remove it.
A
Screw A
Fastener A
Bolt C
B
A
Bolt A
Cover
５． Disconnect the fog light harness connector.
（Fog light equipped vehicles only）
CAUTION
• The removed parts will be reused. Store the removed
parts in a manner that facilitates remembering their
installation positions, and be careful not to damage or lose
them.
• Placed the removed bumper on a protective sheet to
prevent scratches.
Front bumper
Hole cover removal（Fog light not equipped vehicles）
Hole cover
Tab
１． Remove the screw (1), detach the tabs (3 locations) by
pressing them to the outside, and then remove the hole cover
in the direction of the arrow.
CAUTION
＜Cross section＞
Screw
Tab
• The removed hole cover are not used to install this
accessory.
NOTE
• The figure shows the right side, however, perform the
same procedure for the left side.
Hole cover
Fog light bezel removal（Fog light equipped vehicles）
Screw
Fog light
１． Remove the screws (2), detach the tabs (3 locations) by
pressing them to the outside, and remove the fog light and fog
light bezel in the direction of the arrow as a single unit.
２． Remove the bolt (1) and the screw (1), and then remove the
fog light and fog light bezel.
CAUTION
• The removed fog light bezel are not used to install this
accessory.
• The removed fog light, bolt (1) and screws (2) are to
be reused. Be careful not to damage or lose them.
Screw
Fog light bezel
Tab
Adjusting
bolt
Fog light bezel
＜Cross section＞
NOTE
• The figure shows the right side, however, perform the
same procedure for the left side.
─４─
５．FOG LIGHT INSTALLATION
NOTE
• The figure shows the right side, however, perform the same procedure for the left side.
Fog light bezel processing
Filing area
１． File the areas around the hole indicated in the figure on the
left using a round file.
CAUTION
• Be careful not to scratch the surface of the fog light bezel.
Round file
Fog light bezel
Fog light equipped vehicles,
or separately purchased fog light
Fog light bezel
Fog light bezel installation
１． Assemble the kit fog light bezel with the fog light (fog light
equipped vehicles, or separately purchased fog light) using
the screw (1) and bolt (1).
CAUTION
• Only partially tighten the fog light adjusting bolt at this point
in the procedure, as it will be completely tightened after
completing the aiming adjustment.
Screw
Front bumper
Adjusting bolt
Screw
２． Secure the fog light bezel to the front bumper using the
screws (2) and the tabs (3 locations).
Tightening torque
Screw：0.3−1.5 N･m {3.0−15.0 kgf･cm・2.6 – 13.2 in･lbf }
CAUTION
Screw
• Tighten the screw securely
Make sure to tighten to the specified torque. If tightened
outside the specified torque, the front fog light bezel or
front bumper could be damaged or fall off.
─５─
６．PART INSTALLATION
Front bumper installation
１． Peel off the tape wrapped around the vehicle wiring harness.
(When installing fog lights on a vehicle not equipped with fog lights)
Vehicle wiring harness
Headlight
Peel off tape
Front bumper
Fog light equipped vehicles,
or separately purchased fog light
２． Connect the fog light wiring harness connector to the fog light.
CAUTION
• Make sure that the fog light wiring harness connector is
securely inserted until it locks.
Fog light harness connector
Bolt B
Nut
B
Screw A
A
Fastener A
Bolt C
Bolt C（8 Locations）
Tightening torque：7.8−11.8 N･m
{80.0−120.0 kgf･cm・70.0 – 104.0 in･lbf }
Bolt B（2 Locations）
Tightening torque：4.9−7.9 N･m
{50.0−80.0 kgf･cm・43.0 – 69.0 in･lbf }
Nut（4 Locations）
Tightening torque：6.9−9.8 N･m
{70.0−100.0 kgf･cm・61.0 – 86.0 in･lbf }
Bolt A（2 Locations）
Tightening torque：7.8−11.8 N･m
{80.0−120.0 kgf･cm・70.0 – 104.0 in･lbf }
B
Bolt A
Cover
３． Install the front bumper in the reverse order of removal.
A
Front bumper
CAUTION
• After completing the aiming adjustment, install fastener A
and screw A.
• Tighten the bolt and nut securely
Make sure to tighten to the specified torque. If tightened
outside the specified torque, the front bumper could be
damaged or fall off.
─６─
７．OPERATION CHECK
Disconnect the negative battery cable
WARNING
• Before starting the engine, make sure nobody is in front or back of the vehicle, or in the engine compartment. If
the vehicle were to move suddenly it could cause a serious accident.
• Do not start the engine in a place such as a garage or other location with poor air ventilation. Otherwise,
poisoning or asphyxiation could result from accumulation of exhaust gas.
CAUTION
Disconnecting the battery causes the DSC indicator light to become inoperable.
（At this point, the DSC OFF indicator light flashes and the TCS/DSC indicator light is illuminated.）
To restore the DSC to an operable condition, perform the following procedures:
１．Turn the ignition switch to the ON position.
２．Turn the steering wheel completely to the right and then completely to the left.
３．Verify that the DSC OFF indicator light goes out.
４．Turn the ignition switch off and then turn it to the ON position again.
５．Verify that the TCS/DSC indicator light goes out.
If the TCS/DSC or DSC OFF indicator lights do not go out after turning the ignition switch to the ON
position, consult your Mazda dealer.
When the battery is disconnected, the windows will not fully open and close automatically.
Perform the following procedure to resume operation:
１． Turn the ignition switch to the ON position.
２． Press the switch and fully open the window.
３． Pull up the switch and continue holding for about 2 seconds to fully close the window.
８．FOG LIGHT AIMING
１． Adjust the tire pressure to the specification.
２． Position the unloaded vehicle on a flat, level surface.
３． Seat one person in the driver’s seat.
４． Line up the headlights with the white screen at a distance of
3m {9.8ft} apart.
3m {9.8ft}
５． Place an object in front of the fog light not being adjusted to
block its light beam.
Downward
Tightening torque
Adjusting bolt：1.0−3.4 N･m
{10.0−34.0 kgf･cm・8.9 – 30.0 in･lbf }
Upward
Adjusting bolt
Same for both
Right and left
６． Start the engine so that the battery remains charged.
７． Turn the front fog light on.
８． Bend back the undercover, loosen the aiming adjustment bolt
below the fog light, adjust the center of the fog light to the position
shown in the figure, and tighten the bolt.
Center of fog light
60mm{2.4in}
CAUTION
• Tighten the aiming adjustment bolt securely. Otherwise the
aiming could deviate if the bolt loosens.
Make sure to tighten to the specified torque. If tightened
outside the specified torque, the fog light bezel could be
damaged or fall off.
Brightness
borderline
─７─
INSTALLATION
INSPECTION
SHEET
MX-5
FOG LIGHT BEZEL
N121 V7 247F（SILVER）
N123 V7 247F（BLACK）
Inspection after installation
• Inspect the installed / reinstalled parts for the following items.
Check Item（○）
Inspection Parts
Fog light bezel
Scratches/Dirt/ Installation/
Tightening/
Clearance/Fit Harness
Engagement
interference
○
○
○
Fog light
○
○
○
Front bumper
○
○
○
Adjustment
Operation
check
○
○
Installation inspection sheet for fog light bezel
Date
,
,
VIN.
Person in
charge
Checked
Approved
The term of validity for this sheet: 3 months