back
USERS GUIDE
RF Mechanical Programmable Room Thermostat, 24 Hour
LOGIC+ Combi, LOGIC Combi & LOGIC Combi E
24, 30, 35
When replacing any part on this appliance, use only spare parts that you can be
assured conform to the safety and performance specification that we require.
Do not use reconditioned or copy parts that have not been clearly authorised by Ideal.
204812-4.indd 1
15/12/2011 14:37:02
back
LOGIC COMBI, LOGIC + COMBI & LOGIC COMBI E
RF Mechanical Programmable Room Thermostat, 24 Hour
Note. To access user instructions on room
thermostat/programmer, slide cover marked “info”.
Outer dial
2
1
24
3
SETTING UP
23
4
5
21
24hr clock
6
20
3
9
7
19
Align current
time to arrow
Slide clock cover off.
22
12
Note that the outer dial is printed with the 24hr clock
8
18
8.00am = 8 on the dial,
9
17
Clock hands will allow for fine adjustment of the current
time setting of the dial.
15
14
13
10
8.00pm = 20 on the dial.
16
6
The outer dial should be set to the current time. Rotate
the dial slowly in a clockwise direction, until the correct
hour is aligned with the arrow printed on the dial.
12
11
esp9460a
Do not attempt to rotate the dial in an anti-clockwise
direction.
The national regulations and respective safety instructions are to be observed.
Interferences and changes to the device will lead to cancellation of the warranty.
2
204812-4.indd 2
15/12/2011 14:37:02
back
PROGRAMMING SWITCHING TIMES
Outer dial
Set tappets to outer edge for ON periods and set tappets to inner
edge for OFF periods.
2
1
24
3
The example shown has been set with 2 on periods.
23
22
12
4
5
21
6
3
9
7
ON at 6.00pm. (18 hours) OFF at 10.00pm (22 hours)
8
18
9
17
6
16
15
14
10
11
13
12
setting temperatures
24hr clock
19
Align current
time to arrow
20
ON at 9.00am. OFF at 1.00pm. (13 hours)
esp9460a
Turn the temperature dial to the room
temperature you would like the central
heating to achieve during central heating
on periods.
Switches between
OFF & ON. dependant on
position of tappets.
Outer dial
2
MANUAL SWITCH OPERATION
1
24
3
5
24hr clock
6
20
3
9
7
19
Align current
time to arrow
8
18
To set the programmable room thermostat to be continuously on, move the
switch labelled “OFF/ /ON” to the “ON” position.
9
17
6
16
15
14
10
11
13
12
To set the programmable room thermostat to be continuously off, move the
switch labelled “OFF/ /ON” to the “OFF” position.
22
21
To set the programmable room thermostat for timed operation moved the
switch labelled “OFF/ /ON” to the “ “ position.
23
12
4
esp9460a
3
204812-4.indd 3
15/12/2011 14:37:03
back
BATTERY REPLACEMENT
The low battery warning LED on the front of the unit will flash yellow to
indicate battery replacement. The unit will continue normal operation until
the LED flashes red and the unit will stop operation.
To replace batteries remove the front of the programmable room thermostat
from the mounting panel to gain access.
Reset Button
(under cover)
The unit required 2 x AA 1.5V Batteries.
Batteries should operate for approximately 18 months.
Low Battery Warning LED
Only good quality 1.5V alkaline batteries should be used. DO NOT use
re-chargeable batteries as they only have a terminal voltage of 1.2V
nom.
If the batteries are not replaced and no signal is received by the receiver,
the light on the front of the receiver on the boiler will flash rapidly.
After 1 hour the boiler will operate in “Emergency Mode” (heating on for 4
mins and off for 9 mins) until the batteries are replaced.
Batteries 2 x AA
3G9465a
Once batteries have been replaced, ALWAYS operate the reset button.
November 2011
UIN 204812 A04
Ideal Stelrad Group pursues a policy of continuing improvement in the design and performance
of its products. The right is therefore reserved to vary specification without notice.
Ideal Boilers Ltd., P.O. Box 103, National Ave, Kingston Upon Hull, HU5 4JN.
Tel. 01482 492251 Fax. 01482 448858. Registration No. London 322 137.
204812-4.indd 4
15/12/2011 14:37:04