GE Indoor Lighting Fixtures Low Bay Versabeam Disconnect

advertisement
g
INDOOR LIGHTING
GE
Lighting Solutions
GUIDE FORM SPECIFICATIONS
versabeam tm luminaire with optical sliding disconnect and charcoal filter
high bay or low bayenclosed
GENERAL DESCRIPTION
The complete luminaire designated _____ (identify) shall be a
GE VERSABEAMTM luminaire with Optical Sliding Disconnect and
Charcoal Filter, ordering number _____ (specify VS5, plus ordering number logic from catalog) or approved equal, to operate
one _____ (specify [200,250 or 400] watt high pressure sodium
[HPS], [175, 250 or 400] watt metal halide or [250, 320, 350 or
400] watt pulse start metal halide) lamp from a nominal _____
(specify 120, 208, 220, 240, 277, 347 or 480) volt, 60 Hz or (220,
230, 240 or 380) volt, 50 Hz power source. The luminaire shall
include a completely prewired integral ballast and optical assembly. The luminaire shall be suitable for continuous service
indoors in a maximum ambient temperature of _____ (specify
55°C "400 watts max" or 65°C "250 watts max"). The luminaire
shall be UL Listed SUITABLE FOR DAMP LOCATIONS, UL Listed
for metal halide lamps in polymeric lamp containment barriers
and C-UL (Canadian) Listed for Indoor Locations. Standard construction is IP52. Units with “W” (Wet Location) option are IP54.
MECHANICAL CONSTRUCTION
For ease of installation and to facilitate maintenance and replacement, the luminaire shall be supplied as components —
ballast and optical.
The ballast housing and optical assembly shall be provided
with easy‑to‑read moisture‑resistant nameplates which can be
seen without disturbing the installed luminaire. All ballast and
optical assemblies shall include provisions for optional field
mounting of safety chains.
The ballast housing, including mounting plate, shall be of diecast aluminum. The ballast housing shall have an electrocoat
gray paint finish.
To facilitate mounting, the luminaire shall have separate lightweight mounting components that can be easily removed from
the ballast housing and assembled to the structural or mounting hardware prior to mounting of the remainder of the luminaire. The mounting device must provide a positive vibrationresistant locking means including a set screw.
The wiring access cover plate and all screws requiring removal
during normal conduit mounting and/or wiring shall be captive.
The Ballast housing shall incorporate GELS EZ Connect™ ­
plug-in wiring harness that provides for easier wiring
­installation and quick replacement.
EZ Connect™ plug-in wiring harness shall enable the use of a
*GELS Critique™ plug-in diagnostic test device.
BALLAST OPERATION
The luminaire shall contain a standard _____ (specify Mag‑Reg
[for HPS lamps] or Autoreg [for metal halide and mercury
lamps]) type ballast* in full compliance with lamp‑ballast specifications available to the fixture manufacturer from the lamp
manufacturers at the time of fixture manufacture.
The ballast shall reliably start and operate the lamp in ambient
temperatures down to ‑20°F for mercury and metal halide or
‑40°F for HPS.
The luminaire and ballast shall be from the same ­manufacturer.
OPTICAL ASSEMBLY
Mounting of the optical assembly to the ballast assembly must
be secured by positive, vibration-resistant means. The optical
and ballast assemblies must include a positive aligning electrical sliding disconnect between optical and ballast components.
The disconnect must have no exposed live metal parts.
The optical assembly shall contain an E39 mogul base socket
with superior lamp gripping. The socket shall have the ability to
handle the higher pulse ratings of newer HID systems.
The optical assembly shall be enclosed with a continuous
gasket and shall include an activated charcoal filter capable of
filtering gaseous and particulate matter. The filter shall be constructed to permit free passage of air, allowing the luminaire to
breathe during normal off-on heating and cooling cycles and
therefore eliminating unnecessary stress on the gasketing.
The filter assembly shall be factory installed, and shall be
located to prevent accidental dislodgment when luminaire is
installed.
The optical assembly shall have a patented acrylic refractor
with reflecting and refracting prisms that provide 70% output
from 0° to 60° from nadir, 60% output from 15° to 50° from nadir.
The optical assembly shall be hinged and latched with captive
vibration-resistant stainless steel spring latches.
The reflector material shall be formed aluminum, with a
chemically bonded lightweight non-breakable glass ALGLAS ®
finish on both inside and outside surfaces providing corrosion
resistance, durability and easy cleaning.
* REFER TO PRODUCT PAGE IN GELS PRODUCT ­CATALOG FOR
OTHER BALLAST SELECTIONS AND ­CRITIQUE™ ­DIAGNOSTIC TEST
DEVICE CAPABILITY. FOR MORE DEFINITIVE ELECTRICAL INFORMATION, REFER TO BALLAST SPECIFICATIONS IN TECHNICAL
DATA SECTION.
Guide Form Specifications – 2011
g
GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com
1-88 8 - 6 9 - 4 3-5 3 3
GE Lighting Solutions is a subsidiary of the General Electric Company. Evolve and other trademarks belong to GE Lighting Solutions. The GE brand and logo are trademarks of the General Electric Company.
© 2011 GE Lighting Solutions. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.
Download