2012 Your Complete Source for Stamped Steel Bearing Housings & Bronze Bushed Bearing Assemblies With so many styles and sizes to choose from you are sure to find what you need at Manitou Mfg. • Stamped Steel Bearing Housings. • Bronze Bushed and Plastic Bearings. • Porous & Cast Hard Bronze Bushings. • Buy Direct from the Manufacturer & SAVE! • Made in USA since 1946 FOR INSTANT ORDERING OR MORE INFORMATION CALL TOLL FREE: 1-800-894-1509 P.O. Box 10526 • White Bear Lake, MN 55110-0526 Local: 651-429-4285 • Toll Free: 1- 800-894-1509 • Fax: 651-429-5765 Email: info@manitoumfg.com • Web Site: www.manitoumfg.com Table of Contents Flanges, Two-Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1 Three and Four-Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2 - 3 Triangular Three-Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4 Three and Four-Bolt Re-Lube. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5 Stainless Steel, Pillow Block Sets and Flanges. . . . . . . . . . . . . . . . . . . . . . . . Page 6 Pillow Block Stands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7 Pillow Block Housing Sets, Non-Snap-Together. . . . . . . . . . . . . . . . . . . . . . . . Page 8 Snap-Together . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 9 Notched Snap-Together and Stainless Steel. . . . . . . . . . . . . . . . . . . Page 10 Rubber Boots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11 Flush Mounts, Two and Three Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12 Two-Bolt Flush Mounts (Rubber Booted) . . . . . . . . . . . . . . . . . . . . Page 13 Take-Up Units -- MSTU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 13 Side Mounts, Junior Flange and Center Flange-Gee . . . . . . . . . . . . . . . . . . . Page 14 Two-Bolt Flange Side Mounts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 15 Four-Bolt Flange Side Mounts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 16 500 Series Pillow Blocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 17 600 Series Flange-Gee Bearing Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 18 700 Series Heavy Duty Pillow Blocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 19 800 Series Heavy Duty Flange-Gee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 19 Plastic Bearings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 20 UHMW-PE Side Mounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 20 UHMW-PE Bearing Inserts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 21 UHMW-PE Flush Mount Bearing Assemblies. . . . . . . . . . . . . . . . . . . . . . . . . Page 21 Porous Bronze Bushings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 22-23 Cross Reference Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 24 Parts Made to Your Prints. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inside Back Cover Condition of Sale/Shipping/Return Policy. . . . . . . . . . . . . . . . . . . . Inside Back Cover This catalog supersedes all other Manitou Mfg. Co. Catalogs Two-Bolt Flanges For Standard Ball Bearing Units We have supplied these flanges as housing units for standard ball bearings made by SKF, Fafnir, Sealmaster, Linkbelt, and many others. One housing unit consists of two identical self-aligning flanges. Each pair of flanges has a spherical inside surface which mates with the spherical outer surface of the ball bearing ring to provide self-alignment in any direction. A minimum of space is required for installation as the unit protrudes thru the frame, plate, or panel on which it is installed. The flanges listed below are standard and are dimensionally the same as supplied by the leading ball bearing manufacturers. Manitou Shaft Stamping Size Number A B C D E F H J Steady Bolt Radial Size Load Rating 35M-2 1/2, 9/16 5/8 35MM 2-5/16 3-3/16 2 1/2 7/32 9/32 1-5/8 .062 1/4 350 40M-2 1/2 & 5/8 40MM 2-5/16 3-3/16 2 1/2 9/32 9/32 1-15/16 .075 1/4 600 40M-2-SS Same as 40M-2 except made from grade 304 stainless steel 42M-2 3/4 42MM 2-19/32 3-9/16 2-13/16 9/32 11/32 1-15/16 .065 5/16 400 47M-2 3/4 47MM 2-5/8 2-13/16 5/16 11/32 2-3/16 .083 5/16 700 Same as 47M-2 except made from grade 304 stainless steel,, .089 .09 Thick Thick 47M-2-SS 52M-2 3-9/16 7/8 to 1 52MM 2-51/64 3 3/4 3 11/32 11/32 2-3/8 .083 5/16 800 Same as 52M-2 except made from grade 304 stainless steel, .08 Thick .089 Thick 52M-2-SS 52M-2B 7/8 to 1 62M-2 1-1/16 to 1 - 62MM 3-5/16 1/4 62M-2B 1-1/16 to 1 - 62MM 3-5/16 1/4 72M-2 1-1/4 to 72MM 3-11/16 4-15/16 3-15/16 7/16 1-7/16 13/32 3-3/16 .104 3/8 1400 72M-2B 1-1/4 to 72MM 3-11/16 4-15/16 3-15/16 1/2 1-7/16 13/32 3-3/16 .149 3/8 1400 Printed in U.S.A. 3 3/8 13/32 11/32 11/32 2-13/32 .134 5/16 1700 4-7/16 3-9/16 3/8 11/32 13/32 2-13/16 .104 3/8 1100 4-7/16 3-9/16 3/8 13/32 13/32 2-27/32 .134 3/8 1700 52MM 2-51/64 3 3/4 .149 Thick for Heavy Thrust Load WHEN ORDERING FLANGES, PLEASE SPECIFY PLAIN OR ZINC PLATED FINISH. Two-Bolt Flanges are not available with a grease fitting. Page 1 Three-Bolt and Four-Bolt Flanges for Standard Ball Bearing Units The flanges listed are standard and are dimensionally the same as supplied by the leading ball bearing manufacturers. Two flanges are required to house a standard ball bearing unit, but Manitou sells them individually. The spherical inside surface of each pair of flanges mates with the spherical outer surfaces of the ball bearing rings to provide self-alignment in any direction. Manitou Stamping Number B C G D A Stock Bolt Bolt Hole Hole Minimum Flange Flange Width Frame Diameter Shoulder Thickness Size Circle Diameter Opening Width 40MM-3 1/2 & 5/8 1-15/16 3-3/16 9/32 .075 1/4 47MM-3 3/4 2-3/16 3-9/16 5/16 .083 5/16 2-13/16 47MM-3B Manitou Stamping Manitou Number 52MM-3 Manitou Stamping Stamping Number 40MM-3 Number 52MM-3B Manitou 47MM-3 40MM-3 Stamping 40MM-3 Number 47MM-3 52MM-3E 47MM-3B 47MM-3 3/4 A 2-3/16 Minimum A Frame A Minimum 2-3/8 Opening Minimum Frame 1-15/16 Frame Opening A 2-3/8 Opening 2-3/16 Minimum 1-15/16 1-15/16 Frame 2-3/16 2-3/8 Opening 2-3/16 2-3/16 B 3-9/16 Flange B Diameter 3Flange 3/4B Flange Diameter 3-3/16 Diameter 3 3/4B 3-9/16 Flange 3-3/16 3-3/16 Diameter 3-9/16 3 3/4 3-9/16 3-9/16 5/16C Flange C Shoulder C 11/32 Flange Width Flange Shoulder 9/32 Shoulder Width C 11/32 Width 5/16 Flange 9/32 9/32 Shoulder 5/16 3/8 Width 5/16 5/16 .083 G Stock G Thickness G Stock .083 Stock Thickness .075 Thickness .083 G .083 Stock .075 .075 Thickness .083 .104 .083 .083 5/16 Bolt Size Bolt 5/16 Bolt Size 1/4 Size 5/16 5/16 Bolt 1/4 1/4 Size 5/16 5/16 5/16 2-13/16 D Bolt Hole D Circle DHole Bolt 3 Diameter Bolt Hole Circle 2 1/2 Circle Diameter D 3 Diameter 2-13/16 Bolt 2 1/2Hole 2Circle 1/2 2-13/16 3 Diameter 2-13/16 2-13/16 40MM-3 47MM-3B 52MM-3-1 47MM-3B 52MM-3 47MM-3 52MM-3 52MM-3H 52MM-3 47MM-3B 52MM-3B 52MM-3B 52MM-3 52MM-3B 52MM-3E 62MM-3 52MM-3E 52MM-3E 52MM-3B 52MM-3-1 52MM-3-1 52MM-3-1 52MM-3E 62MM-3B 52MM-3H 52MM-3H 52MM-3-1 52MM-3H 62MM-3 62MM-3GP-3 52MM-3H 62MM-3 62MM-3 62MM-3-SS 62MM-3B 62MM-3 62MM-4 62MM-3B 62MM-3B 62MM-3GP-3 62MM-3B 62MM-3GP-3 72MM-3 62MM-3GP-3 62MM-3-SS 62MM-3-SS 62MM-3-SS 62MM-3GP-3 62MM-4 72MM-3GP 62MM-4 62MM-3-SS 62MM-4 72MM-3 62MM-4 72MM-BC 72MM-3 72MM-3 Page 2 Shaft Size 72MM-3GP 72MM-3 72MM-4 72MM-3GP 72MM-3GP 72MM-BC 80MM-4 72MM-3GP Shaft 7/8,Size 15/16 Shaft & 1Shaft Size 1/2 & 5/8 Size 7/8, 15/16 & 1 3/4 1/2 Shaft & 5/8 1/2 & 5/8 Size 7/8, 15/16 3/4 & 1 3/4 3/4 1/2 &15/16 5/8 7/8, 3/4 7/8, 3/41 15/16 & 3/41 & 7/8, 15/16 7/8, 15/16 7/8, 15/16 & 3/41 & &1 1 & 1 7/8, 15/16 1-1/16, 7/8, 15/16 & 1 15/16 7/8, 1-1/8 &1 1 & 1-3/16, 7/8, 15/16 1-1/4 & 1 15/16 7/8, &1 1-1/16, 7/8, 15/16 7/8, 1-1/8 & 1 15/16 &1 1 1-3/16, & 7/8, 15/16 1-1/4 7/8, & 1 15/16 1-1/16, &1 1-1/8 1-1/16, 1-1/16, 1-1/81-3/16, 1-3/16, 1-1/16, 7/8, 15/16 1-1/8 1-1/4 1-1/8 &1 1-3/16, 1-3/16, 1-1/16, 1-1/4 1-1/16, 1-1/4 1-1/8 1-1/8 1-1/16, 1-3/16, 1-1/16, 1-3/16, 1-1/8 1-1/4 1-1/8 1-1/4 1-3/16, 1-3/16, 1-1/4 1-1/16, 1-1/16, 1-1/4 1-1/81-3/16, 1-1/8 1-1/4, 1-1/16, 1-1/4 1-1/16, 1-3/16, 1-5/16 1-1/81-3/16, 1-1/81-3/16, 1-3/8, 1-1/4 1-1/4 1-7/16 1-1/16, 1-1/81-3/16, 1-1/8 1-1/4, 1-1/16, 1-1/4 1-5/16 1-3/16, 1-1/16, 1-1/8 1-1/4 1-3/8, 1-1/8 1-3/16, 1-7/16 1-3/16, 1-1/4, 1-1/4 1-1/16, 1-1/4 1-1/4, 1-5/16 1-1/8 1-1/4, 1-3/8, 1-5/16 1-1/4, 1-3/16, 1-5/16 1-3/8, 1-7/16 1-5/16 1-1/4 1-3/8, 1-7/16 1-3/8, 1-7/16 1-1/4, 1-1/4, 1-7/16 1-5/16 1-1/4, 1-5/16 1-1/4, 1-5/16 1-3/8, 1-1/4, 1-3/8, 1-5/16 1-7/16 1-3/8, 1-5/16 1-7/16 1-3/8, 1-7/16 1-3/8, 1-7/16 1-1/4, 1-1/4, 1-7/16 1-1/2, 1-5/16 1-5/16 1-1/4, 1-3/8, 1-9/16 1-1/4, 1-3/8, 1-5/16 2 1/2 1-15/16 2-3/16 2-3/8 2-3/16 2-3/8 2-3/16 3-3/16 3-9/16 3 3/4 3-9/16 3 3/4 3-9/16 9/32 5/16 25/64 5/16 11/32 5/16 .075 .083 .134 .083 .083 1/4 5/16 5/16 5/16 5/16 2 1/2 2-13/16 3 2-13/16 3 2-13/16 2-3/8 2-3/8 2-3/16 2-3/8 3 3/4 3 3/4 3-9/16 3 3/4 11/32 11/32 5/16 11/32 .083 .083 .083 5/16 5/16 5/16 3 3 2-13/16 3 2-3/8 2-3/8 2-3/8 2-13/16 2-3/8 2-3/8 3 3/4 3 3/4 3/4 3 4-7/16 3 3/4 3 3/4 11/32 11/32 3/8 11/32 3/8 3/8 11/32 25/64 .083 .083 .104 .104 .104 .104 .083 .134 5/16 5/16 5/16 3/8 5/16 5/16 3 3 3-9/16 3 3 9/32 11/32 21/64 ROUND 21/64 BOLT HOLES Hole Width Hole 11/32 Hole Width 9/32 Width 21/64 ROUND BOLT HOLES 11/32 Hole 9/32 9/32 Width 21/64 ROUND 11/32 .104 THICK 21/64 11/32 BOLT HOLES 21/64 ROUND 9/32 .134 THICK FOR HEAVY 21/64 21/64 HOLES ROUND 11/32 BOLT 21/64 THRUST 11/32 11/32 BOLT HOLES 11/32 21/64 ROUND 13/32 Has Round Bolt Holes 11/32 21/64 21/64 ROUND BOLT HOLES BOLT HOLES 21/64 ROUND BOLT HOLES 11/32 21/64 ROUND BOLT HOLES 11/32 .104 THICK 13/32 11/32 .104 THICK .134 FOR HEAVY .104 THICK THICK 21/64 ROUND BOLT HOLES 11/32 THRUST .134 THICK FOR HEAVY 2-3/8 3 3/4 25/64 .134 5/16 3 11/32 .134 THICK FOR HEAVY .149 THICK FOR THRUST 2-3/8 3 3/4 3/4 25/64 .134 5/16 3-9/16 3 11/32 Has 3/8 .104 .104Round THICK 2-13/16 4-7/16 13/32 .149 3/8 13/32 2-3/8 3 11/32 .083 5/16 3 Bolt Holes HEAVY THRUST THRUST LOAD 2-3/8 3 3/4 11/32 .083 5/16 3 13/32 .134 Has Round Bolt Holes THICK FOR HEAVY 25/64 .134 11/32 Has Round Bolt Holes 2-3/8 3 3/4 11/32 .083 5/16 3 13/32 THRUST 2-13/16 4-7/16 11/32 .104 3/8 3-9/16 3-9/16 13/32 2-13/16 4-7/16 25/64 .134 3/8 13/32 2-3/8 3 3/4 .083 5/16 3-9/16 3 2-13/16 4-7/16 11/32 .104 3/8 13/32 Has Round Bolt Holes 2-13/16 4-7/16 11/32 .104 3/8 3-9/16 13/32 Same as 62MM-3 above except made from 304 Stainless Steel .149 THICK FOR 2-13/16 4-7/16 13/32 .149 3/8 3-9/16 13/32 HEAVY THRUST LOAD 2-13/16 4-7/16 11/32 .104 3/8 3-9/16 13/32 .149 THICK FOR 2-13/16 4-7/16 11/32 .104 3/8 3-9/16 13/32 4 Bolt Holes 13/32 .149 .149 THICK FOR LOAD HEAVY THRUST 2-13/16 4-7/16 13/32 .149 3/8 3-9/16 13/32 HEAVY THRUST LOAD 2-13/16 4-7/16 25/64 .134 3/8 3-9/16 13/32 .149 THICK FOR 2-13/16 4-7/16 13/32 .149 3/8 3-9/16 13/32 HEAVY THRUST LOAD 2-13/16 4-7/16 25/64 .134 3/8 3-9/16 13/32 3-3/16 4-13/16 3/8 .104 3/8 3-15/16 13/32 2-13/16 25/64except.134 3/8 Stainless 3-9/16 Steel 13/32 Same as 4-7/16 62MM-3 above made from 304 Same as 62MM-3 above except made from 304 Stainless Steel Same as 4-7/16 62MM-3 above made from 304 2-13/16 25/64except.134 3/8 Stainless 3-9/16 Steel 13/32 2-13/16 4-7/16 11/32 .104 3/8 3-9/16 13/32 3-3/16 4-13/16 7/16 .134 3/8 3-15/16 13/32 2-13/16 11/32except.104 3/8 Stainless 3-9/16 Steel 13/32 Same as4-7/16 62MM-3 above made from 304 2-13/16 4-7/16 11/32 .104 3/8 3-9/16 13/32 4 Bolt Holes .134 Thick 4 Bolt Holes 4 Bolt Holes 3-3/16 2-13/16 3-3/16 3-3/16 3-3/16 4-13/16 4-7/16 4-13/16 4-13/16 4-13/16 3/8 11/32 13/32 3/8 3/8 .104 .104 .149 .104 .104 3/8 3/8 3/8 3/8 3/8 3-15/16 3-9/16 3-15/16 3-15/16 3-15/16 13/32 13/32 13/32 13/32 13/32 .149 4 BoltTHICK Holes FOR HEAVY THRUST LOAD 3-3/16 3-3/16 3-3/16 3-3/16 3-3/16 4-13/16 4-13/16 4-13/16 4-13/16 4-13/16 7/16 3/8 3/8 7/16 7/16 .134 .104 .104 .134 .134 3/8 3/8 3/8 3/8 3/8 3-15/16 3-15/16 3-15/16 3-15/16 3-15/16 13/32 13/32 13/32 13/32 13/32 .134 Thick 4 Bolt Holes .134 Thick .134 Thick 3-3/16 3-9/16 3-3/16 4-13/16 5-13/16 4-13/16 13/32 7/16 .149 .134 .134 3/8 1/2 3/8 3-15/16 4-11/16 3-15/16 13/32 17/32 13/32 .149 THICK FOR .134 Thick HEAVY THRUST LOAD .149 THICK FOR Printed in U.S.A. 1-3/8, 1-3/8, 1-7/16 1-7/16 1-1/4, 1-1/4, 1-5/16 1-5/16 72MM-3C 72MM-BC 72MM-BC 1-3/8, 1-3/8, 1-7/16 1-7/16 3-3/16 3-3/16 4-13/16 4-13/16 13/32 13/32 .149 .149 3/83/8 3-15/16 3-15/16 13/32 13/32 72MM-4 72MM-4 1-1/4, 1-1/4, 1-5/16 1-5/16 1-3/8, 1-3/8, 1-7/16 1-7/16 3-3/16 3-3/16 4-13/16 4-13/16 3/83/8 .104 .104 3/83/8 3-15/16 3-15/16 13/32 13/32 4 Bolt 4 Bolt Holes Holes 80MM-4 80MM-4 1-1/2, 1-1/2, 1-9/16 1-9/16 3-9/16 3-9/16 5-13/16 5-13/16 13/32 13/32 .134 .134 1/21/2 4-11/16 4-11/16 17/32 17/32 80MM-4SQ 80MM-4SQ 1-1/2, 1-1/2, Square Square 1-9/16 1-9/16 1-1/2, 1-9/16 .149 .149 THICK THICK FOR FOR HEAVY HEAVY THRUST THRUST LOAD LOAD 4-3/4" 4-3/4" square, square, otherwise otherwise same same asas 80MM-4 80MM-4 above above 3-5/8 5-13/16 5/8 .149 1/2 4-11/16 17/32 3-13/16 3-3/16 5- 7/8 7/16 .134 1/2 4- 3/4 17/32 3-5/8 5-13/16 5/8 .149 1/2 4-11/16 17/32 1- 5/8, 1-11/16 1-3/4, 3-13/16 3-3/16 5- 7/8 5/8 7/16 .149 .134 1/2 4- 3/4 17/32 1- 5/8, 5/8, 85MM-4GP 11-11/16 85MM-4BSQ 1-11/16 1-3/4, 1-3/4, 3-13/16 3-13/16 5- 7/8 4-3/4 Square 5/8 7/16 .149 .149 1/2 1/2 4- 3/4 4- 3/4 17/32 17/32 1- 5/8, 1- 5/8, 85MM-4BSQ 1-11/16 1-11/16 85MM-4GP-3 1-3/4, 1-3/4, 3-13/16 3-13/16 4-3/4 Square 5- 7/8 7/16 21/32 .149 .179 1/2 1/2 4- 3/4 4- 3/4 17/32 17/32 1- 5/8, 87MM-4 87-MM-4 85MM-4GP-3 1-11/16 1-3/4, 3-7/8 3-13/16 5- 3/4 7/8 21/32 .134 .179 1/2 4- 3/4 17/32 & 17/32 37/64 4 3-7/8 6-1/8 5- 3/4 7/16 21/32 .149 .134 1/2 5 4- 3/4 80MM-4GP 85MM-4 80MM-4GP 85MM-4GP 85MM-4 90MM-4 90-MM-4 87-MM-4 1- 5/8, 1-11/16 1-3/4, 1-1/2, 1-9/16 1-13/16, 1-7/8, 1-15/16 1-13/16, 1-13/16, 90MM-4GP 90-MM-4GP 1-7/8, 90-MM-4 1-7/8, 1-15/16 1-15/16 4 4 6-1/8 6-1/8 7/16 7/16 .164 .149 1/2 1/2 5 5 90MM-4BSQ 90-MM-4BSQ Square 90-MM-4GP 1-13/16, 1-13/16, 1-7/8, 1-7/8, 1-15/16 1-15/16 5-1/8" square, otherwise same as 90MM-4GP above. 4 6-1/8 7/16 .164 1/2 5 90MM-4GP-3 90-MM-4GP-3 90-MM-4BSQ Square 1-13/16, 1-13/16, 1-7/8, 1-7/8, 1-15/16 1-15/16 4 6-1/8 21/32 .179 1/2 5 5-1/8" square, otherwise same as 90MM-4GP above. 100MM-4 100-MM-4 90-MM-4GP-3 2-2-1/16, 2, 2-1/16, 1-13/16, 2-1/8, 1-7/8, 2-3/16 1-15/16 4-7/16 4 6- 9/16 6-1/8 15/32 21/32 .149 .179 1/2 1/2 5- 7/16 5 100MM-4GP 100-MM-4GP 100-MM-4 2, 2-1/16, 2-2-1/16, 2-2-1/16, 2-1/8, 2-1/8, 2-3/16 2-3/16 4-7/16 4-7/16 6- 9/16 6- 9/16 15/32 15/32 .164 .149 1/2 1/2 5- 7/16 5- 7/16 2-2-1/16, 2, 2-1/16, 100MM100-MM100-MM-4GP 2-1/8, 4GP-4 2-3/16 4GP-4 2-2-1/16, 4-7/16 6- 9/16 11/16 15/32 .194 .164 1/2 5- 7/16 .149 Thick for Heavy Thrust Load .149 .149 Thick for Thick Heavyfor Heavy Thrust Thrust Load Load .149 .179 for Thick Thick for Heavy Heavy Thrust Thrust Load Load .179 Thick for Heavy Thrust Load 17/32 & 37/64 .164 Thick for Heavy 17/32 17/32 Thrust Load .164 Thick for Heavy 17/32 Thrust Load .179 Thick for Heavy 17/32 Thrust Load .179 Thick 17/32 for Heavy 17/32 Thrust Load .164 Thick for Heavy 17/32 17/32 Thrust Load .194 .164 Thick for Heavy 17/32 Thrust Load .194 Thick Page 3 Triangular Three-Bolt Flanges for Standard Ball Bearing Units These triangular steel stampings are the same as our round 40MM-3, 47MM-3, 52MM-3, 62MM-3 and 72MM-3 parts. They are used where space is limited. One housing unit consists of two identical self-aligning flanges. Each pair of flanges mates with the spherical outer surface of the ball bearing ring to provide self-alignment in any direction. A minimum of space is required for installation as the unit protrudes thru the frame, plate, or panel on which it is installed. The flanges listed below are standard and are dimensionally the same as supplied by the leading ball bearing manufacturers. Dimensions of Pressed Steel Flanges , .075 Thick 3- 5/32 5/16 , .075 Thick TRIANGULAR FLANGES ARE NOT AVAILABLE WITH A GREASE FITTING. Page 4 WHEN ORDERING FLANGES, PLEASE SPECIFY PLAIN OR ZINC PLATED FINISH. Printed in U.S.A. Standard Re-Lube Three & Four- Bolt Flanges for Standard Ball Bearing Units These flanges are used where additional lubrication is required. For example, where dust, dirt, excessive moisture, or other contaminants are present. The additional lubrication increases the life of the ball bearing unit by flushing out any contaminants that may be present, plus lubricating the ball bearing unit over a longer period of time. The side with the grease fitting has an inner grease groove, which allows the grease to enter the holes in the outer ring of the ball bearing. The other side has a similar grease groove. Order each side seperately. Printed in U.S.A. Page 5 Stainless Steel Pillow Block Sets and Flanges Page 7 mblies. Grade Steel Bearing Housings GRADE304 304 Stainless STAINLESS STEEL BEARING HOUSINGS Manitou Part Number 40M-2-SS 40MM-3T-SS 47M-2-SS 47MM-3T-SS 52M-2-SS 52MM-3T-SS 62MM-3-SS 62MM-3G-SS 40PBM-SS-N 47PBM-SS-N 52PBM-SS-N 62PBM-SS-N 40PBM-SS-EW 47PBM-SS-EW 52PBM-SS-EW 62PBM-SS-EW Page 6 2 Bolt Flange 3 Bolt Tri Flange 2 Bolt Flange 3 Bolt Tri Flange 2 Bolt Flange 3 Bolt Tri Flange 3 Bolt Flange 3 Bolt Relube Flange Pillow Block Pillow Block Pillow Block Pillow Block Pillow Block Pillow Block Pillow Block Pillow Block See P1 See P4 See P1 See P4 See P1 See P4 See P2 See P5 See P10 See P9 See P10 See P9 See P10 See P9 See P10 See P9 See P10 See P9 See P10 See P9 See P10 See P9 See P10 P9 For See Dimensions Printed in U.S.A. Pillow Block Stands Our MPB- - Stands are excellent quality parts which are used where speeds are moderate and loads are medium. These are used in place of the expensive Cast Iron or Malleable Iron Pillow Block units, under the above conditions. The flanges listed below are standard and dimensionally have the same distance between bolt hole centers and base to center line. A Two-Bolt flange is required to retain ball bearing, bolt together (ordered seperately). ALL OF THESE PARTS ARE ZINC PLATED. Printed in U.S.A. Page 7 Heavy Duty Steel Pillow Block Sets for Standard Ball Bearing Units These units consist of a two piece heavy gauge steel housing which allows the ball bearing initial self-alignment. Manitou Pillow Block Sets are made from heavier gauge steel than the standard. The housings listed below are standard and are dimensionally the same as supplied by the leading ball bearing manufacturers. These parts are plated with Zinc and dipped in clear chromate to resist corrosion. (Bearing not included) Top Strap Gauge Base Strap Gauge -ZP 14 16 -ZP 12 14 -ZP 12 12 -ZP 10 12 -ZP 10 12 This Pillow Block Design can be used on conveyors that go around curves. Our customers state that the ball bearing does not bind because this unit does not have vertical edges on the tops and bases. For your satisfaction, we suggest an actual test of the ball bearing and housing assembly in your application. If you have a problem with a housing and feel we could be of assistance and possibly save you some money, please advise. Page 8 Printed in U.S.A. Snap-Together Heavy Duty Steel Pillow Block Sets for Standard Ball Bearing Units These units consist of a two-piece heavy gauge steel housing which allows the ball bearings initial self-alignment. The housings listed below are standard and are dimensionally similar to those supplied by the leading ball bearing manufacturers. These parts are plated with Zinc and dipped in clear chromate to resist corrosion. Our Heavy Duty Steel Pillow Block sets are made from heavier gauge steel than the standard. These units are further strengthened by the turned down edges of both top and bottom straps. These same edges will serve to retain the rubber boot when boots are used for sound deadening. Top Strap Gauge Base Strap Gauge -ZP 14 14 -ZP 14 14 -ZP 12 12 10 12 10 12 -ZP -ZP For your satisfaction, we suggest an actual test of the ball bearing and housing assembly in your application. If you have a problem with a housing and feel we could be of assistance and possibly save you some money, please advise. Printed in U.S.A. Page 9 72PBM-HR-N-ZP 1- 5/16 5- 3/4 4- 1/4 3/4 17-32 3- 1/8 1- 9/16 72MM 1- 1/4, 1- 5/16, 1- 3/8, 1- 7/16 1- 7/32 1- Page 10 Printed in U.S.A. Rubber Ball Bearing Boots Rubber boots can be used in Snap Together Pillow Block Sets and with our Stamped Flanges. Made from static conductive nitrile rubber. Rubber Boot R-4 R-5 R-6 R-7 Spherical OD of Ball Bearing 40MM 47MM 52MM 62MM Manitou Pillow Block Set 47MPB-ST-ZP, 47PBM-HR-ZP, or 47PBM-SS-N 52MPB-ST-ZP, 52PBM-HR-ZP, or 52PBM-SS-N 62MPB-ST-ZP, 62PBM-HR-ZP, or 62PBM-SS-N 72MPB-ST-ZP, 72PBM-HR-ZP The Rubber Boot or Grommet surrounds the ball bearing and fits in between the base and top strap of the Pillow Block Set. A Pillow Block Set without turned down edges on the top strap, and turned up edges on the base will not work, as the rubber flows out of the unit in use when any thrust is applied. The above Manitou Pillow Block Sets have the proper edges on both base and top strap. This is the type of unit, where the base and top strap have the “Snap Together” feature. RUBBER BALL BEARING BOOTS OR GROMMETS R-4 For 40 M/M Bearing –– Mount with 47 MM Housing R-5 For 47 M/M Bearing –– Mount with 52 MM Housing R-6 For 52 M/M Bearing –– Mount with 62 MM Housing R-7 For 62 M/M Bearing –– Mount with 72 MM Housing We Carry These In Stock Printed in U.S.A. Page 11 MANITOU Flush Mounts Flush Mounting’s for your standard cylindrical O.D. ball bearings, or we can produce a plastic or bronze insert. No frame opening required. MFM units have same bolt spacings as corresponding standard flanges. Please remember we don’t sell ball bearings. 30-2-MFM 2-13/16 2-1/8 1-15/16 1.18 (30 MM) .354 .066 .760 13/16, 7/8, 15/16, 1 13/16, 7/8, 15/16, 1 1-3/16, 62-3-MFM Page 12 We carry UHMW-PE bearing inserts in various shaft sizes for the mountings above. Printed in U.S.A. Two-Bolt Flush Mounts (Rubber Booted) Flush mounted zinc plated pressed steel two-bolt units including static conductive rubber boots for noise and vibration reduction. Needs no frame opening. Designed for standard ball bearings with cylindrical OD of 40MM, 47MM, and 52MM. Covers all standard shaft sizes from ½” thru 1”. Choose proper unit number for your application from chart below. Includes stamped housing and rubber boot only. Remember, Manitou doesn’t carry ball bearings. Stamped Housing No. MSTU Series Stamped Take-Up Units These Zinc plated light duty pressed steel tightening and adjustment units are designed to be used with standard 2-bolt flanges and ball bearings with spherical OD. Two-Bolt flanges sold separately. Printed in U.S.A. Page 13 manitou bearing assemblies Junior size Flange Side Mounts “160 series” PoROUs Bronze Ball Units The porous bronze bearing has an oil capacity of one-third of its volume and the oil is fed to shaft by self-metering capillary action. Additional lubrication is usually unnecessary in applications where these units are used, so no oil cups or grease fittings are provided. Center Flang-Gee “170 Series” This three bolt complete flang-gee bearing assembly shown below has the same ball assembly as the “160” Series. The steel housing consists of two identical self-aligning 16 gauge flanges. They are easily mounted in any position - horizontally, vertically, or at any angle. Only three ¼” bolts are required to attach to frame. These bolts should be tightened evenly when mounted. This unit is stronger than the above types but requires a hole in the frame so the assembly can protrude slightly thru the frame. * These Bearing Assemblies are fully self-aligning, due to spherical construction of both the housing and bearing. * EASY INSTALLATION - just bolt them down * RUST RESISTANT FINISH - Zinc plating on steel parts is attractive, rust resistant. * LOW IN COST * IMMEDIATE SHIPMENT FROM STOCK - Your order (large or small) will be shipped immediately. Page 14 *UHMW Bearings also available, see page 20. Printed in U.S.A. Two-Bolt Flange Side Mounts Complete, Inexpensive, Self-Aligning Porous Bronze Sleeve-type * EASY INSTALLTION - Just bolt them down * ALL UNITS SELF-ALIGNING - Speeds production, cuts costs, improves performance. * EXTRA HEAVY GAUGE STEEL USED IN ALL TOP AND BOTTOM FLANGES * LOW IN COST * IMMEDIATE SHIPMENT FROM STOCK - Your order (large or small) will be shipped immediately * RUST RESITANT FINISH - Zinc plating on steel parts is attractive and rust resistant. Stock Shaft Sizes: 1/2”, 5/8”, 3/4”, 13/16” , 7/8”, 15/16” , 1”, and 1-1/16” Printed in U.S.A. *UHMW Bearings also available, see page 21. Page 15 Four-Bolt Flange Side Mounts Complete, Inexpensive, Self-Aligning Porous Bronze Sleeve-type * EASY INSTALLTION - Just bolt them down * ALL UNITS SELF-ALIGNING - Speeds production, cuts costs, improves performance. * EXTRA HEAVY GAUGE STEEL USED IN ALL TOP AND BOTTOM FLANGES * LOW IN COST * IMMEDIATE SHIPMENT FROM STOCK - Your order (large or small) will be shipped immediately * RUST RESITANT FINISH - Zinc plating on steel parts is attractive and rust resistant. Stock Shaft Sizes: 1/2”, 5/8”, 3/4”, 13/16” , 7/8”, 15/16” , 1”, and 1-1/16” Page 16 *UHMW Bearings also available, see page 21. Printed in U.S.A. 500 Series Pillow Blocks (Unit with 15/16” Base to Centerline Instead of 1-1/16”. Can Be Furnished On Request) These units are self-aligning due to the spherical construction of the inner housing which conforms to a spherical socket formed in the outer housing. The porous bronze bearing has an oil capacity of one-third of its volume. The large oil reservoir with the close fitting wick which surrounds the bearing, provides ample lubrication at all times. The outer housing or top strap is made of a 12 gauge steel. The base is sprung slightly when the bolts are tightened which insures proper pressure between inner and outer housing so as to permit free self-alignment and yet maintain the inner housing in correct position. Zinc plating on steel parts is attractive and rust resistant Stock Shaft Sizes: 1/2”, 5/8”, 3/4”, 13/16” , 7/8”, 15/16” , 1”, and 1-1/16” low cost • all units self-aligning • easy to install *UHMW Bearings and Stainless Steel Straps available, see page 21. Printed in U.S.A. See Page 19 for Additional Pillow Blocks. Page 17 Flange Mounted Bearing Assemblies “600 Series” “610 Series” “620 Series” A FRAME Opening is required for installation as the unit protrudes thru the frame, plate, or panel on which it is installed. This is a very strong unit because the load is directly over the center of the two flanges. BEARING - High quality bronze graphitized bearings provide ample lubrication. Bearing has a flange to carry thrust load and provides self-lubrication bearing surface for thrust collar. GREASE LUBRICATED - The large lubricant reservoir is filled through standard Threaded Grease Fittings. Stock Shaft Sizes: 1/2”, 5/8”, 3/4”, 13/16” , 7/8”, 15/16” , 1”, and 1-1/16” low cost • all units self-aligning • easy to install *UHMW Bearings also available, see page 21. Page 18 Printed in U.S.A. 700 Series Heavy Duty Pillow Blocks These rugged self-aligning Pillow Blocks were designed for applications where heavy loads and higher speeds are encountered. These units are self-aligning due to the spherical construction of the inner housing which conforms to a spherical socket formed in the outer housing. The base is sprung slightly when the bolts are tightened which insures proper pressure between inner and outer housing so as to permit free self-alignment and yet maintain the inner housing in correct position. The outer housing or top strap is made from 10 gauge steel and the base from 12 gauge. They can be installed either in horizontal or vertical position. Standard units are supplied with threaded grease fittings and the units have large grease reservoirs. Zinc plating on steel parts is attractive and rust resistant. Special units furnished on request. Available in the following shaft sizes: 7/8”, 1”, 1-1/16”. 1-1/8”, 1-3/16”, 1-1/4”, 1-3/8” 800 Series Heavy Duty Flange-gee This illustrated three bolt complete Flang-Gee bearing assembly has the same ball assembly as the “700 Series” Pillow Blocks. The steel housing consists of two identical self-aligning 12 gauge flanges. They are easily mounted in any position - horizontally, vertically or at any angle. Only three 3/8” bolts are required to attach to frame. These bolts should be tightened evenly when mounted. This unit is interchangeable with any standard 62M flange ball bearing unit with a 3-9/16” bolt circle. Can also be used as a two-bolt assembly with our 62M-2 or extra heavy 62M-2B flanges. In addition, they can be used as a three-bolt assembly with our 62MM-3T (triangular) flanges to save space. Available in the following shaft sizes: 7/8”, 1”, 1-1/16”. 1-1/8”, 1-3/16”, 1-1/4”, 1-3/8” FLANG-GEES - are furnished with threaded Zerk-type fittings. THE MINIMUM OF SPACE is required for installation as the unit protrudes thru the frame, plate, or panel on which it is installed. This is a very strong unit because the load is directly over the center of the two flanges. BEARING - High quality bronze graphitized bearings provide ample lubrication. GREASE LUBRICATED - The large lubricant reservoir is filled through standard Threaded Grease Fittings. Printed in U.S.A. *UHMW Bearings also available, see page 21. Page 19 Plastic Bearings 1/2” to 1-1/2” I.D.’s Available Spherical or cylindrical O.D. up to 62MM UHMW-PE Stocked, but available in various materials Stock or made to your specifications Variety of mounting styles to choose from, including stainless steel Lightweight and chemical resistant Great for use on food grade equipment, boat lifts, paddle boats, exercise equipment, conveyors, etc. UHMW-PE JUNIOR SIZE FLANGE SIDE MOUNTS “U160-SERIES” Page 20 Part No. U160-1/4 U160-5/16 U160-3/8 U160-1/2 Shaft Size 1/4” 5/16” 3/8” 1/2” Printed in U.S.A. UHMW-PE BEARING INSERTS Spherical UHMW-PE Bearing Inserts can be used in our stamped steel flanges and in a variety of our pillow blocks. Listed below are the insert’s we carry in stock. If you don’t see exactly what you need, give us a call, we will be happy to discuss your options. Insert and housing sold separately. UHMW-PE FLUSH MOUNT BEARING ASSEMBLIES 12 Printed in U.S.A. Page 21 POROUS BRONZE BUSHINGS Page 1 Porous Bronze Bushings porous bronze sleeve and flange type bearings. Oil-filled, self lubricating, Oil-filled, self lubricating, porous sleeveblocks and flange type bearings. These are the same fine quality bushings which we use inbronze our pillow and flange mounted bearing assemblies. These are the same fine quality bushings which we use in our pillow blocks and flange mounted bearing assem DIMENSIONS DIMENSIONS PART NUMBER Diameter Inside Diameter Outside Length P110-6 3/16 .1895 5/16 .3155 3/4 P120-4 1/4 .252 3/8 .378 1/2 AA-519-1 1/4 .252 1/2 .5015 1/2 P140-3 P140-4 P140-5 P140-6 P140-12 3/8 .377 .377 .377 .377 .377 1/2 .503 .503 .503 .503 .503 3/8 1/2 5/8 3/4 1/2 P150-6 3/8 .377 5/8 .628 3/4 P165-4 P165-5 P165-6 P165-8 P165-10 1/2 .502 .502 .502 .502 .502 5/8 .628 .628 .628 .628 .628 1/2 5/8 3/4 1 1-1/4 P170-6 P170-8 1/2 .502 .502 11/16 .6905 .6905 3/4 1 P175-4 P175-6 P175-7 P175-8 P175-10 P175-12 1/2 .502 .502 .502 .502 .502 .502 3/4 .753 .753 .753 .753 .753 .753 P180-4 P180-5 P180-6 P180-8 P180-10 5/8 .6270 .6270 .6270 .6270 .6270 3/4 .753 .753 .753 .753 .753 Page 22 1/2 3/4 7/8 1 1-1/4 1-1/2 1/2 5/8 3/4 1 1-1/4 PART NUMBER Diameter Inside Diameter Outside Length P190-4 P190-5 P190-8 P190-9 P190-1-7/16 5/8 .6270 .6270 .6270 .6270 .6270 7/8 .878 .878 .878 .878 .878 1/2 5/8 1 1-1/8 1-7/16 P195-6 11/16 .690 7/8 .878 3/4 P200-5 P200-6 P200-7 P200-8 P200-12 P200-13 3/4 .7525 .7525 .7525 .7525 .7525 .7525 7/8 .878 .878 .878 .878 .878 .878 5/8 3/4 7/8 1 1-1/2 1-5/8 P210-4 P210-6 P210-7 P210-8 P210-9 P210-10 P210-12 P210-16 3/4 .7525 .7525 .7525 .7525 .7525 .7525 .7525 .7525 1 1.004 1.004 1.004 1.004 1.004 1.004 1.004 1.004 1/2 3/4 7/8 1 1-1/8 1-1/4 1-1/2 2 P215-017 13/16 .815 1 1.004 1-1/16 P220-7 P220-8 P220-017 P220-10 7/8 .878 .878 .878 .878 1 1.004 1.004 1.004 1.004 7/8 1 1-1/16 1-1/4 P230-4 P230-7 P230-8 P230-10 P230-12 7/8 .878 .878 .878 .878 .878 1-1/8 1.128 1.128 1.128 1.128 1.128 1/2 7/8 1 1-1/4 1-1/2 P233-017 15/16 .940 1-3/16 1.1905 1-1/16 Printed in U.S.A. DIMENSIONS DIMENSIONS PART NUMBER Diameter Inside Diameter Outside Length P235-8 P235-017 P235-10 P235-12 1 1.003 1.003 1.003 1.003 1-1/8 1.129 1.129 1.129 1.129 1 1-1/16 1-1/4 1-1/2 AA-1511-5 1 1.003 1-1/2 1.5045 1-1/2 P240-6 P240-8 P240-017 1 1.004 1.004 1.004 1-3/16 1.1905 1.1905 1.1905 3/4 1 1-1/16 P245-5 P245-6 P245-8 P245-9 P245-10 P245-11 P245-12 P245-14 P245-16 1 1.004 1.004 1.004 1.004 1.004 1.004 1.004 1.004 1.004 1-1/4 1.254 1.254 1.254 1.254 1.254 1.254 1.254 1.254 1.254 5/8 3/4 1 1-1/8 1-1/4 1-3/8 1-1/2 1-3/4 2 P250-6 P250-12 1 1.004 1.004 1-5/16 1.316 1.316 3/4 1-1/2 P255-12 1 1.003 1-3/8 1.377 P260-017 1-1/16 1.064 1-3/16 1.1905 AA-1502-3 1-1/8 1.127 1-1/2 1.5035 1-1/2 P270-12 P270-16 1-1/8 1.1285 1.1285 1-5/16 1.316 1.316 1-1/2 2 P275-12 P275-16 1-1/8 1.1285 1.1285 1-3/8 1.3785 1.3785 1-1/2 2 P280-12 1-3/16 1.1905 Toll Free 800-894-1509 Printed in U.S.A. 1-1/2 1.504 PART NUMBER Diameter Inside Diameter Outside Length P283-8 P283-10 1-1/4 1.254 1.254 1-3/8 1.3785 1.3785 1 1-1/4 P285-7 P285-8 P285-10 P285-12 P285-14 1-1/4 1.254 1.254 1.254 1.254 1.254 1-1/2 1.503 1.503 1.503 1.503 1.503 7/8 1 1-1/4 1-1/2 1-3/4 P287-12 1-1/4 1.252 1-9/16 1.565 1-1/2 P290-8 1-1/4 1.254 1-5/8 1.628 1 P295-8 P295-12 1-3/8 1.3785 1.3785 1-5/8 1.629 1.629 1 1-1/2 P300-4 P300-8 P300-12 P300-14 P300-16 1-1/2 1.504 1.504 1.504 1.504 1.504 1-3/4 1.754 1.754 1.754 1.754 1.754 1/2 1 1-1/2 1-3/4 2 P310-16 1-3/4 1.754 2 2.004 2 P315-6 1-7/8 1.878 2-1/4 2.254 3/4 P330-6 P330-8 P330-16 2 2.004 2.004 2.004 2-1/4 2.254 2.254 2.254 3/4 1 2 P340-16 2-1/2 2.505 2-3/4 2.754 2 1-1/2 1-1/16 1-1/2 FLANGED FLANGED BUSHINGS BUSHINGS DIMENSIONS PART NUMBER Diameter Inside FF-520-10 .3765 F-620-1 .502 F-620-2 .502 F-620-4 .502 F-703 .6265 F-703-6 .6265 F-718-1 .6275 F-843-2 .627 F-911-4 .7505 F-1015-2 .753 F-1001 .8765 F-1001-X .8765 F-1102-X .877 F-1207-5 1.002 FL-102-X 1.003 F-1314-2 1.127 www.manitoumfg.com Diameter Outside Length .502 .627 .627 .627 .7525 .7525 .7525 .877 .941 1.003 1.003 1.003 1.128 1.252 1.254 1.377 3/8 1/2 3/4 1-1/8 1-1/8 1-1/4 1/2 1 1 3/4 1 1-1/8 1 3/4 7/8 1 Flange OD Thick 5/8 1/16 7/8 1/16 7/8 1/16 7/8 1/16 1 3/32 1 3/32 7/8 1/16 1 1/8 1-1/8 3/32 1-1/8 1/8 1-1/4 1/8 1-1/4 1/16 1-3/8 1/8 1-5/8 1/8 1-1/2 1/8 1-3/4 1/8 Fax 651-429-5765 Page 23 Manitou Stamping Interchange Table Manitou Stamping Interchange Table The flangettes below are listed with part numbers denoting clear zinc plating as the finish. Also available unfinished “R” The below are listed with part numbers denoting clear zinc plating Only as theparts finish. Alsowhere available as unfinished "R" or flangettes with yellow dichromate “YZP.” Other finishes available upon request. listed interchange is available. or yellow dichromate "YZP." Other finishes available upon request. Only parts listed where interchange is available. Two Bolt: Three Bolt: Three Bolt Triangular: Three Bolt Relube: Four Bolt: Four Bolt Relube: Pillow Blocks: Page 24 Manitou Fafnir Timken SKF NTN Peer 40M-2ZP 47M-2ZP 52M-2ZP 52M-2BZP 62M-2ZP 62M-2BZP 40MST-ZP 47MST-ZP T52MST-ZP 52MST-3ZP 62MST-ZP 62MST-2ZP 40MST 47MST 52MST 52MST-3 62MST 62MST-3 PFT40 PFT47 PFT52 PFL203 PFL204 PFL205 PFL-3Z PFL-4Z PFL-5Z PFT62 PFL206 PFL-6Z 72M-2ZP 72M-2BZP 40MM-3ZP 47MM-3ZP 52MM-3ZP 52MM-3EZP 62MM-3ZP 62MM-3BZP 72MST-ZP 72MST-3ZP 40MS-ZP 47MS-ZP 52MS-ZP 52MS-2ZP 62MS-ZP 62MS-4ZP 72MST PFT72 PFL207 PFL-7Z 40MS 47MS 52MS 52MS-2 62MS PF40 PF47 PF52 PF203 PF204 PF205 PF-3Z PF-4Z PF-5Z PG62 PF206 PF-6Z 72MM-3ZP 72MM-3CZP 40MM-3TZP 72MS-ZP 72MS-7ZP 72MS PF72 PF207 PF-7Z 47MM-3TZP 52MM-3TZP 62MM-3TZP 72MM-3TZP 52MM-3GZP 52MM-3GPZP 47MSTR-ZP T52MSTR-ZP T62MSTR-ZP T72MSTR-ZP G52MSA-ZP G52MSB-ZP 47MSTR 52MSTR 62MSTR 72MSTR G52MSA G52MSB PFD47 PFD52 PFD62 PFD72 62MM-3GZP 62MM-3GPZP 62MM-3G-3ZP 62MM-3GP-3ZP 72MM-3GZP TG62MSA-ZP TG62MSB-ZP G62MSA-3ZP G62MSB-3ZP TG72MSA-ZP G62MSA G62MSB G62MSA-3 G62MSB-3 G72MSA PF-6Z-TOPS-H PF-6Z-BOTS-G 72MM-3GPZP 62MM-4ZP 72MM-4ZP 80MM-4ZP 80MM-4SQZP TG72MPB-ZP 62MS-2ZP 72MS-5ZP 80MS-ZP T80MS-SZP G72MSB 62MS-2 72MS-5 80MS PF208 PF-7Z-BOTS-G PFF-6Z PFF-7Z PFF-8Z 85MM-4ZP 85MM-4BSQZP 90MM-4ZP 100MM-4ZP 80MM-4GZP 80MM-4GPZP 85MM-4GZP 85MM-4GPZP 90MM-4GZP 90MM-4GPZP 100MM-4GZP 100MM-4GPZP 85MS-ZP T85MS-SZP 90MS-ZP 85MS PF209 PFF-9Z G80MSA-ZP G80MSB-ZP G85MSA-ZP G85MSB-ZP G90MSA-ZP G90MSB-ZP G100MSA-ZP G100MSB-ZP G80MSA G80MSB G85MSA G85MSB G90MSA G90MSB G100MSA G100MSB 40MPB-ST-ZP 47MPB-ST-ZP 52MPB-ST-ZP 62MPB-ST-ZP 72MPB-ST-ZP 40MPB-STAND-ZP 47MPB-STAND-ZP 52MPB-STAND-ZP 62MPB-STAND-ZP 72MPB-STAND-ZP 40PB-ZP 47PB-ZP 52PB-ZP 62PB-ZP 72PB-ZP 40PBS-ZP 47PBS-ZP 52PBS-ZP 62PBS-ZP 72PBS-ZP 40PB 47PB 52PB 62PB 72PB 40PBS 47PBS 52PBS 62PBS 72PBS PFT-3Z PFT-4Z PFT-5Z PFT-6Z PFT-7Z PF-5Z-TOPS-H PF-5Z-BOTS-G PF-7Z-TOPS-H PF80 90MS PFF-10Z PFF-11Z PFF-8Z-TOPS-H PFF-8Z-BOTS-G PFF-9Z-TOPS-H PFF-9Z-BOTS-G PFF-10Z-TOPS-H PFF-10Z-BOTS-G PFF-11Z-TOPS-H PFF-11Z-BOTS-G P40 P47 P52 P62 P72 PP203 PP204 PP205 PP206 PP207 PP-3Z PP-4Z PP-5Z PP-6Z PP-7Z PB-3Z PB-4Z PB-5Z PB-6Z PB-7Z Printed in U.S.A. Parts Made to Your Prints Custom Steel Stamping And Precision CNC Turning Available. Call 1-800-894-1509 or E-mail us at info@manitoumfg.com regarding your products specific size and material requirements. Most likely we can meet your specifications, and we look forward to working with you. “CONDITION OF SALE” The following is made in lieu of all warranties, express or implied: Seller’s only obligation shall be to replace such quantity of the product proved to be defective. Seller shall not be liable for any loss or damage, direct or consequential, arising out of the use of or the inability to use the product. Before using, user shall determine the suitability of the product for his intended use, and user assumes all risk and liability whatsoever in connection therewith. The foregoing may not be changed except by an agreement signed. SHIPPING DISCREPANCIES To keep pricing low, quantities of 100 or more are counted by weight. Adjustments will not be made for shipments that are 2% less than invoiced quantities of 100-499 pieces, nor 1% less than quantities of 500 or more pieces. RETURN POLICY All returns must be authorized by Manitou Manufacturing Co. Please include the reason for return with your request. A $25.00 or 20% restocking charge, whichever is greater, will be deducted from the credit issued on all returns other than shipping error. Customer is to pay the return freight if the return is due to customer error. Upon approved return you will be issued a RMA number, to be included with the parts. Parts must be returned in original condition to receive credit. Credit will be given upon inspection. No returns on special order items. Printed in U.S.A. Page 25 We have over 2,000,000 parts in stock, and we can quote parts made to your prints on special order needs. We have been producing bronze bushed bearing assemblies in White Bear Lake, MN since 1946. We have CNC equipment for increased efficiency, accuracy and flexibility in producing bronze bushed and plastic bearings in shaft sizes up to 1-1/2”. We also carry popular sizes of porous bronze plain and flanged bushings for immediate shipment from our stock. We have the largest selection of Bronze Bushed Bearing assemblies anywhere. With so many styles and sizes to choose from your sure to find what you need at Manitou Mfg. FOR INSTANT ORDERING OR MORE INFORMATION CALL TOLL FREE: 1-800-894-1509 P.O. Box 10526 • White Bear Lake, MN 55110-0526 Local: 651-429-4285 • Toll Free: 1- 800-894-1509 • Fax: 651-429-5765 Email: info@manitoumfg.com • Web Site: www.manitoumfg.com