GRUNDFOS DATA BOOKLET
Vaccuperm VGS-140
High-performance disinfection systems
Vaccuperm VGS-140
Table of contents
1.
General
3
Vaccuperm VGS-140 high-performance disinfection
systems
3
2.
3.
Functional scheme
4
Functional scheme Vaccuperm VGS-141,
VGS-143, VGS-145
4
Technical data
5
Vaccuperm VGS-141, VGS-143, VGS-145
gas dosing systems
Vaccuperm VGS-147 and VGS-148 vacuum
regulators
4.
5.
2
5
7
Accessories
8
High-capacity injectors 545
Combined liquid chlorine trap and
chlorine gas filter LiquFilt 524
Liquid gas evaporator RV 171
Change-over device 185
Change-over device 185-2 with bypass
Vacuum change-over device 186
Pressure reducing valves 544
8
9
10
12
13
15
17
Further product documentation
18
WebCAPS
WinCAPS
18
19
1
Vaccuperm VGS-140
General
1. General
Vaccuperm VGS-140 high-performance disinfection systems
• Pressure sensors for more safety: optional pressure
sensors for injector vacuum and operating vacuum
allow the early detection of disturbances such as
insufficient injector vacuum or vacuum regulator
faults.
• Precise scan system for the flowmeter: the inductive
sensor is insensitive to soiling and does not get into
contact with the aggressive gas to be dosed. The
resolution of the signal is about 2 % of the limit
value of the measuring range.
• Systems with direct proportional control: the
servomotor of the rate valve can optionally be
equipped with electronics (4-20 mA input) for direct
proportional control without additional control
electronics.
2
3c
3b
• Automation of the dosing process: optionally a
microprocessor-based controller can be integrated
for PID control or for compound loop control.
• Ergonomic and service-friendly design: all control
elements and displays are installed at eye-level for
easy handling. Easy change-over from automatic to
manual operation. All assembly and service work
can be executed with a few standard tools.
Note: Vaccuperm VGS-140 are expert systems.
All component configurations must be adapted to the
requirements on site. For assistance, please ask our
product specialists or project department.
18
3a
16
8
7
4
9
15
17
16
5
1a
6
14
16
16
11
Fig. 1
Pos.
12
10
13
TM04 1340 2709
1
Complete installation: drinking water disinfection with chlorine gas
Description
Pos.
Description
1
Chlorine drum
12
1a
Chlorine drum balance
13
Injection unit
2
Control for the pneumatic chlorine drum quick-action stop
valves
14
Chlorine gas sensor
15
Optical and acoustic alarm devices
3
Chlorine drum lifting device
16
Suction nozzle to the chlorine gas neutralization system
3a
Lifting beam
17
Central control panel with computer interface
3b
Spring balance for cranes
18
Sprinkling system
3c
Chain hoist
4
Automatic change-over device
5
Nitrogen rinsing device
6
Chlorine evaporator
7
Pressure reducing valve and filter
8
Vacuum regulator VGS-141 to VGS-148
9
Gas dosing system VGS-141 to VGS-145
10
High-capacity injector
11
Motive water booster pump
Flowmeter with 4-20 mA output
3
2
Vaccuperm VGS-140
Functional scheme
2. Functional scheme
Functional scheme Vaccuperm VGS-141, VGS-143, VGS-145
Front hood with swingingout clear screen
Option: microprocessor-based
PID controller
Option: servomotor with or without
control electronics
Linear rate valve
Vacuum meter
Option: with limit contacts
Gas flowmeter
Option: 4-20 mA scanning
Option: sensor for
operating vacuum
Differential pressure
regulator
Option: with sensor for
injector vacuum
Enclosure with foot for floor
mounting or without foot for
wall mounting
Vacuum regulator
VGS-148 with safety
valve
Option: contact
manometer
TM04 1401 3909
High capacitiy injector
Fig. 2
4
Functional scheme Vaccuperm VGS-141, VGS-143, VGS-145
3
Vaccuperm VGS-140
Technical data
3. Technical data
Vaccuperm VGS-141, VGS-143,
VGS-145 gas dosing systems
• Vacuum dosing system with rate valve
• Material: Polyurethane (enclosure), PVC, PTFE,
FKM, silver-coated nickel-chrome alloy
• Gas flowmeter according to floater principle
• Vacuum meter NG 100 mm
• Manual or automatic adjustment of the dosing flow
• Differential pressure regulator
• Floor mounting unit, covered
• For ammonia and sulphur dioxide on request
Dimensions
390
50
Fig. 3
450
TM04 1341 2709
DN 40=730
DN 20=760
1810
1000
1000
610
VGS-141, VGS-143, VGS-145 with foot for floor mounting
5
3
Vaccuperm VGS-140
Technical data
Technical data
Flow rate
Vacuum connections
Type
PE hose 10/14
VGS-141-010
PVC pipe 20/25
VGS-143-040
PVC pipe 40/50
VGS-145-200
50-1000 g/h
100-2000 g/h
200-4000 g/h
400-8000 g/h
0.5 - 10 kg/h
1-20 kg/h
2-40 kg/h
3.5 - 70 kg/h
6-120 kg/h
10-200 kg/h
Options
Vacuum connections
• For PE hose 8/11, PE hose 12/16, PE hose 1/2",
PVC pipe 12/16, PVC pipe 15/20
Motor
Synchronous motor 3VA, IP55, actuating time
0-100 %: 90 s at 50 Hz, 75 s at 60 Hz, installed on the
rate valve
• 230 V (50/60 Hz) with feedback potentiometer
• 115 V (50/60 Hz) with feedback potentiometer
• 230 V (50/60 Hz), input/output 4-20 mA
• 115 V (50/60 Hz), input/output 4-20 mA
Magnetic inductive gas flow sensor
• Precise scanning for all measuring tubes from 2 to
200 kg/h
Vacuum meter for injector vacuum
• NG 100 with 2 limit contact outputs
• Without vacuum meter
Pressure sensors
• For injector vacuum
• For operating vacuum
• For injector and operating vacuum, signal
evaluation via external PLC, required control
voltage 24 V
Enclosure versions
• Floor mounting unit with hood, open foot
• Wall mounting unit with hood
Spare parts sets
Dosing medium
Chlorine gas
6
For dosing unit
Order No.
VGS-141-010
up to 500 g/h
96729331
VGS-141-010
1000 g/h up to 10 kg/h
96688759
VGS-143-040
10 kg/h up to 40 kg/h
96688761
VGS-145-200
40 kg/h up to 200 kg/h
96088763
3
Vaccuperm VGS-140
Vaccuperm VGS-147 and VGS-148
vacuum regulators
Flow rate
• For line installation, with integrated safety valve,
with grooved flange DN 25 (G 1) without liquid trap
• For ammonia and sulphur dioxide on request.
Dimensions
Vacuum connection
Type
Max. 40 kg/h
PVC pipe 20/25
VGS-147-040
Max. 70 kg/h
PVC pipe 40/50
VGS-148-070
Max. 120 kg/h
PVC pipe 40/50
VGS-148-120
Max. 200 kg/h
PVC pipe 40/50
VGS-148-200
Technical data
Technical data
Options
209
Manometer
52
20/25
Ø 175
106
• 0-16 bar, NG 63, optionally with MIN contact
(N.O./N.C.)
• Without manometer
Testing agents
128
Fig. 4
TM04 1312 2609
171
• Bottle with ammonia for tightness check
DN 25
VGS-147 vacuum regulator
Spare parts sets
Spare parts set for
Order No.
VGS-147-040
96688764
VGS-148-070
96688765
VGS-148-120
96688766
VGS-148-200
96688767
206
125
40/50
245
6/8
DN 25
Fig. 5
TM04 1313 2609
170
245
Ø 50
170
7
VGS-148 vacuum regulator
7
4
Vaccuperm VGS-140
High-capacity injectors 545
Dimensions
H
D2
TM04 1334 2609
D1
The selection of the injector to be used for the specific
task determines the safe functioning of the entire
chlorine gas system. The important criteria are the
motive water pressure and counterpressure as well as
the dosing capacity. The indication of the customer
data and the operating point are necessary for the
decision.
• Due to the special form of the nozzle, the operating
costs are low and efficiency is improved.
• Easy selection of the operating point thanks to the
optimum graduation of the product range.
• The construction according to the flow allows a
reduction of the pressure losses of the non-return
diaphragm valve.
• A safety non-return diaphragm valve according to
the floater principle protects the dosing unit
disposed upstream optimally from the entry of water
or chlorine solution.
• Injectors for ammonia and sulphur dioxide are
available on request.
D1
Accessories
4. Accessories
L
Fig. 6
High-capacity injector 545
Technical data
Dosing
capacity
8
Counterpressure
[bar]
Length
(L)
[m]
Height
(H)
[mm]
Motive water
connection
(D1)
Vacuum connection
(D2)
Chlorine solution
connection
(D1)
Product No.
10 kg/h
0.5 - 3
400
155
PVC pipe 25/32
PE hose 10/14
PVC pipe 25/32
96696669
10 kg/h
0.5 - 3
400
155
Hose NPT 1 1/4"
PE hose 10/14
Hose NPT 1 1/4"
91836339
10 kg/h
3-7
400
155
PVC pipe 25/32
PE hose 10/14
PVC pipe 25/32
96729173
10 kg/h
3-7
400
155
Hose NPT 1 1/4"
PE hose 10/14
Hose NPT 1 1/4"
96729205
20 kg/h
0.5 - 3
480
190
PVC pipe 32/40
PVC pipe 20/25
PVC pipe 32/40
96729067
20 kg/h
3-7
480
190
PVC pipe 32/40
PVC pipe 20/25
PVC pipe 32/40
96706388
40 kg/h
0.5 - 3
710
310
PVC pipe 50/63
PVC pipe 20/25
PVC pipe 50/63
96729072
40 kg/h
3-7
710
310
PVC pipe 50/63
PVC pipe 20/25
PVC pipe 50/63
91836631
70 kg/h
0.5 - 3
650
325
PVC pipe 65/75
PVC pipe 40/50
PVC pipe 65/75
96729139
70 kg/h
3-7
650
325
PVC pipe 65/75
PVC pipe 40/50
PVC pipe 65/75
96729225
120 kg/h
0.5 - 3
720
325
PVC pipe 80/90
PVC pipe 40/50
PVC pipe 80/90
96729141
120 kg/h
3-7
720
325
PVC pipe 80/90
PVC pipe 40/50
PVC pipe 80/90
96729228
200 kg/h
0.5 - 3
825
370
PVC pipe 90/110
PVC pipe 40/50
PVC pipe 90/100
96729122
200 kg/h
3-7
825
370
PVC pipe 90/110
PVC pipe 40/50
PVC pipe 90/100
96729211
4
Combined liquid chlorine trap and
chlorine gas filter LiquFilt 524
Types
LiquFilt 524 separates the impurities in the gaseous
chlorine and catches any liquid chlorine drops.
LiquFilt 524 is an important part of high-capacity
chlorine gas dosing systems. It protects the
downstream dosing units from damage by liquid
chlorine and prevents the obstruction of nozzles and
valve seats. Essential parts of the unit are a rugged
steel vessel filled with chlorine-proof mineral filter
material, and an electric heater strip wrapped around
its casing. The self-regulating strip conveys the heat to
the steel and thus keeps the housing at a constant
temperature, hot enough to evaporate the deposited
liquid chlorine drops.
LiquFilt 524 is installed directly in the chlorine gas line
via its flange connections.
The tube connection needs not to be detached for
exchanging the filter. In order not to interrupt the
chlorine gas supply when exchanging the filter, we
recommend the installation of a bypass line with three
shut-off valves.
LiquFilt trap and filter with heather strip 115 V or
230 V (50/60 Hz)
Description
Accessories
Vaccuperm VGS-140
Type
524-205
Accessories
Description
Product No.
Steel pipe, G 1/2, DIN 2441, 1 m, ∅21.3
96727447
Steel pipe, G 1, DIN 2441, 1 m, ∅33.7
96727448
Pair of welding neck flanges DN 25, PN 16, groove
and tongue, DIN 2633/2512
96698366
Pair of threaded flanges G 1, PN 16, groove and
tongue, DIN 2566/2512
96727563
Reducing part G 1 to G 1/2
96727557
Spare parts
Description
Spare parts for LiquFilt 524
Product No.
91835919
Dimensions
290
Fig. 7
TM04 1331 2609
130
~ 490
190
LiquFilt 524
Technical data
Max. flow
200 kg/h chlorine gas
Nominal pressure
16 bar
Test pressure
23 bar
Nominal heating
capacity
80 W at 10 °C
Material
high-grade seamless steel, Rockwool gasket,
asbestos-free material
Input
groove flange DN 25 (G1), DIN 2527/2512
Output
tongue flange DN 25 (G1), DIN 2527/2512
Weight
22 kg
9
4
Vaccuperm VGS-140
Accessories
Liquid gas evaporator RV 171
Technical data
The automatic evaporator transforms the liquid gas
taken from the storage tank by heating. The heat
transfer medium is either water containing
anticorrosive and antifreezer, or oil.
The liquid gas to be vapourized flows under pressure
into the lower part of the evaporator, passes
preheating, evaporating and progressive heating zone
and leaves it as a dry saturated gas flow at the top.
In order to protect the downstream installations up to
the pressure reducing valve from reliquefaction of the
gas, the evaporator is designed generously,
considering the gas outlet temperature.
A bursting disk with connected expansion tank ensures
that the highest admissible operating pressure is not
exceeded. This tank is dimensioned in a way to
transform the overpressure after the bursting of the
bursting disk into the normal operating pressure. If the
bursting disk bursts, this is indicated by a contact
manometer.
A contact manometer with two adjustable limit contacts
indicates too high or too low gas pressure.
• The compact and maintenance-free multitubular
heat exchanger is designed for the evaporation of
liquid chlorine yet also suitable for ammonia and
sulphur dioxide.
• Chlorine quantities of up to 200 kg/h can be
evaporated at temperatures from 5 °C to 60 °C
(water) or 68 °C to 72 °C (oil)
• Protection from overheating and overpressure
• High operational safety due to the use of proven
materials resistant against the dosing media.
Power consumption
9 kW (171-100), 18 kW (171-200)
Voltage
230/400 V (50/60 Hz)
Weight
approx. 220 kg, including load section and
control panel
Max. operating
pressure
12 bar, with bursting disk 16 bar
Testing pressure
33 bar
Admissible ambient
temperature
0-40 °C
Warming-up time
approx. 4 minutes (water), 5-7 minutes (oil)
Connection inlet
groove flange DN 25 (G 1), DIN 2635/2512
Connection outlet
tongue flange DN 25 (G 1), DIN 2635/2512
Dimensions
~ 730
~ 670
1293
1805
DN 25
14
Fig. 8
10
Liquid gas evaporator RV 171W
TM04 1314 2609
100
125
203
DN 25
Types
Heat transfer medium
Water
Oil
Evaporation capacity
Type
100 kg/h
171W-100
200 kg/h
171W-200
100 kg/h
171-100
200 kg/h
171-200
4
Vaccuperm VGS-140
Functional scheme RV 171W-100, -200
Accessories
Selection
Voltage of heating elements
• 230/400 V (50/60 Hz)
• 240/415 V (50/60 Hz)
• 220/380 V (50/60 Hz)
9
Voltage of circulation pump
6
4
3
8
• 220-240 V (50 Hz), IP42/F
• 220-240 V (60 Hz), IP42/F
Voltage of control panel
7
• Load section: 380-415 V (50/60 Hz), with supply for
gas pressure reducing valve
• Control section: 24 V DC, options: digital display
unit, Profibus DP.
5
Accessories
Description
10
2
Product No.
Shut-off valve DN 25 (G 1), inlet and outlet side,
full-way valve chlorine and ammonia
96706446
Flange set: pair of counterflanges (threaded
flanges), G 1, PN 16, DIN 2566/2512, with screws
and sealings
96727563
Flange set: pair of counterflanges (welding neck
flanges), DN 25, PN 16, DIN 2633/2512, with
screws and sealings
TM04 1336 2609
1
96698366
Spare parts sets
Fig. 9
Evaporator RV 171W-100, -200
1
Heat exchanger
6
2
Liquid chlorine intake
7
Bursting disk
Expansion vessel
8
Filler neck for the heat
transfer medium (water)
3
Gas outlet
4
Heating elements
9
Equalizing tank
5
Circulation pump
10
Drain valve
Functional scheme RV 171-100, -200
Product No.
Spare parts set: bursting disk 16 bar, copper line
for contact manometer
95705524
Gasket set: gaskets for heating elements, flat
gaskets for inlet and outlet connection, gaskets for
bursting disk and pipe connections
96688864
8
10 5 9
2
3
6
7
1b
1a
1
4
TM04 1403 2609
Description
Fig. 10 Evaporator RV 171-100, -200
1
Tank
5
1a
Tubular bundle
6
Agitator
Bursting disk
1b
Thermal oil
7
Expansion tank
2
Inlet connection
8
Contact manometer
behind the bursting disk
3
Outlet connection
9
Contact manometer
(operation manometer)
4
Heating flange
10
Contact thermometer
11
4
Vaccuperm VGS-140
Accessories
Change-over device 185
The change-over device is installed between two gas
container batteries to ensure an uninterrupted gas
supply. It automatically changes over from the empty
battery to the full standby battery.
• Application: liquid or gaseous chlorine under
pressure.
• Reliable change-over function due to the two
independent motor valves with manual operation in
case of power failure.
• Overload-proof single-phase AC motors for valve
actuation.
• Practically no leakage losses thanks to the PTFE
packings of the stuffing boxes.
• High functional safety and resistance to wear and
tear thanks to the materials resistant against the
dosing media.
• Indication of the switching status of the valves with
control lamps.
• Transmission of the operating status via a
potential-free changeover contact.
75
124
275
Dimensions
384
160
Fig. 11 Change-over device 185-1 without bypass
12
TM04 1315 2609
180
100
867
4
Vaccuperm VGS-140
Accessories
Change-over device 185-2 with bypass
The change-over device 185-2 with bypass allows
manual operation during maintenance of the
servomotors. Opening and closing of the motor valves
is made in manual operation with electrical
pushbuttons.
340
475
475
110
396
493
Dimensions
110
TM04 1316 2609
180
100
1170
Fig. 12 Change-over device 185-2 with bypass
227
300
37
200
230
TM04 1317 2609
420
400
445
Ø9
Fig. 13 Control panel for 185
13
4
Vaccuperm VGS-140
Functional scheme
Nominal pressure
16 bar
Testing pressure
23 bar
Connection inlet
groove flange DN 25 (G 1)/PN16,
DIN 2527/2512
Connection outlet
tongue flange DN 25 (G 1)/PN16,
DIN 2527/2512
Material
4
valve body
and flanges:
steel
valve balls:
stainless steel
gaskets:
PTFE, glass-fibre
reinforced
lines:
seamless drawn steel
tube to DIN EN10255
Protection
IP65
Actuating time 0-100 %
15 sec. at 50 Hz, 12.5 sec. at 60 Hz
Outputs
3 potential-free outputs; max. charge:
250 V AC, 10 A / 250 V DC, 1 A
Power consumption
0.1 kW
Weight
Admissible ambient
temperature
WI
WI
P
1
P
2
Fig. 14 Change-over device 185
185-1:
approx. 20 kg
185-2:
approx. 30 kg
0 to +40 °C
Types
Description
Type
Change-over device without bypass, 2 motor
valves, contact manometer, control panel 230 V
(50 Hz)
185-1
Change-over device with bypass with shut-off
valves, 2 motor valves, contact manometer, control
panel 230 V (50 Hz)
185-2
Options
Flow
• Up to 200 kg/h chlorine gas, up to 600 kg/h liquid
chlorine
Voltages
•
•
•
•
•
Control panel and motor valves 230 V (50 Hz), IP65
Control panel and motor valves 230 V (60 Hz), IP65
Control panel and motor valves 115 V (60 Hz), IP65
Control panel and motor valves 115 V (50 Hz), IP65
Without control panel, motor valves 230 V
(50/60 Hz)
• Without control panel, motor valves 115 V (60 Hz)
Accessories
Description
14
3
TM04 1402 4009
Accessories
Technical data
Product No.
Set of threaded flanges DN 25 (G 1)/PN16,
connection flange DIN 2566/2512
96727576
Gasket set: gaskets for groove-and tongue flanges
96688979
1
Drum balance
3
Change-over device 185
2
Chlorine drum
4
Control panel
4
Vaccuperm VGS-140
Accessories
Vacuum change-over device 186
The vacuum change-over device is controlled via the
control panel by two contact manometers and
automatically changes over from the empty battery to
the full standby battery.
• Application: chlorine gas under vacuum.
• The change-over device consists of a 3-way ball
valve, an electric servomotor and a control panel.
• At the inlet side, it is connected to two vacuum
regulators; at the outlet side it is connected to a
dosing unit.
• Both contact manometers are mounted either
directly at the vacuum regulators or at the end of the
header line before the vacuum regulators.
Dimensions
>111
145
100
45
Ø40
Ø86
232
187
62
132
95
138
190
TM04 1337 2609
30
50
Fig. 15 Vacuum change-over device 186
15
4
Vaccuperm VGS-140
Accessories
Dimensions control panel
Functional scheme 186
D
227
F
C
F
D
E
Ø8.5
420
400
440
G
G
B
H
TM04 1319 2609
H
300
Fig. 16 Control panel for 186
Technical data
Maximum flow
Servomotor
Control panel
up to 120 kg Cl2 per hour
protection:
IP65
actuating time 0-100 %:
4 seconds
admissible ambient
temperature:
0 to +40 °C
admissible storage
temperature:
-10 to +50 °C
weight:
2 kg
protection:
IP54
weight:
8.5 kg
Options
Connections
• PVC pipe 32/40
• PVC pipe 40/50, extensions
• PVC pipe 20/25, reductions
Voltage of control panel
• 115 V or 230 V (50/60 Hz)
Fastening material
• for wall mounting
Labelling of the control panel
•
•
•
•
German
English
French
Spanish
Types
Description
Vacuum change-over device with control panel
230 V (50/60 Hz)
Type
186-120
Spare parts
Description
Maintenance kit: ball valve without servomotor for
186-120
16
Product No.
95720552
Fig. 17 Functional scheme 186
A
Line from the containers
E
B
Line to the dosing unit
F
Control panel
Vacuum regulator
C
Change-over device
186-120
G
Overpressure line to the
absorption tank
D
Pressure reducing valve
H
LiquFilt 524
TM04 1320 2609
A
A
4
Vaccuperm VGS-140
Pressure reducing valves 544
• The pressure reducing valve 544 reduces the
unregulated gas pressure of the gas containers to a
constant operation pressure.
• It ensures the precise and pressure-independent
functioning of the inlet valve of the vacuum regulator
and prevents re-liquefaction of the gas.
• If the reducing valve is additionally equipped with a
servomotor, it protects the dosing unit against the
penetration of liquefied gas by its immediate shut-off
function in case of malfunctions of the system.
• If the operating pressure exceeds the setpoint
value, the spring-cone-diaphragm system causes
the valve to close.
• If the pressure reducing valve 544 is connected to a
Conex DIA-G or DIS-G gas warning system, the
valve will be immediately closed in case of a gas
breakout.
Nominal pressure
16 bar
Counterpressure
adjustable 2 to 3 bar
Weight
Materials
6 kg
G 1/2, without servomotor
12.5 kg
G 1, without servomotor
9.5 kg
G 1/2, with servomotor
16 kg
G 1, with servomotor
diaphragm:
fine silver
valve cone:
tantal
valve seat:
PVDF
spring:
nickel-chrome alloy, silver plated
O-rings:
FKM
enclosure:
brass
Order data
Max.
flow
Diameter
Connection
Servomotor
Product No.
-
96693065
G 1/2
230 V
50/60 Hz
96729024
115 V
50/60 Hz
96729025
Dimensions
DN 15
~35
H
40 kg/h
200 kg/h
D
T1
L1
T
Accessories
Technical data
DN 25
G1
-
96729019
230 V
50/60 Hz
96729028
115 V
50/60 Hz
96729031
Suitable flanges see accessories below.
2
L2
Options
Pressure reducing valves with servomotor
H
Servomotor: linear-attached actuator with no-voltage
readjusting device, closing time approx. 5.5 s
(at max. stroke), setting time 100 %, admissible
ambient temperature 0 to +50 °C, protection IP54
• 230 V, 50 Hz, 22 mA, 20 W
• 115 V, 60 Hz, 60 mA, 21.6 W.
TM04 1333 2609
Accessories
162
Fig. 18 Pressure reducing valve without servomotor
(above), with servomotor (below)
Connection
H
D
L1
L2
T1
T2
Type
G 1/2
200
120
198
240
128
240
544-101
G1
220
150
240
-
128
255
544-102
G 1/2
425
120
198
240
128
240
544-210
G1
435
150
240
-
128
255
544-220
Description
Product No.
Manometer 0 to 16 bar, G 1/4 (only for chlorine)
96688685
Wall mounting bracket, steel
96728842
Connection set for copper pipe 6/8 (only G 1/2)
96727550
Pair of threaded flanges (connection flange),
groove and tongue, DN 15
96727553
Set of threaded flanges (counter flange), groove
and tongue, DN 15, with screws and sealings
96727556
Pair of threaded flanges (connection flange),
groove and tongue, DN 25
96706818
Set of threaded flanges (counter flange), groove
and tongue, DN 25, with screws and sealings
96727563
Spare parts sets
Description
Product No.
Spare parts set for valve type 544-101, -210
96688978
Spare parts set for valve type 544-102, -220
91835913
17
5
Vaccuperm VGS-140
Further product documentation
5. Further product documentation
WebCAPS
WebCAPS is a Web-based Computer Aided Product
Selection program available on www.grundfos.com.
WebCAPS contains detailed information on more than
220,000 Grundfos products in more than
30 languages.
Information in WebCAPS is divided into six sections:
• Catalogue
• Literature
• Service
• Sizing
• Replacement
• CAD drawings.
Catalogue
Based on fields of application and pump types, this section
contains the following:
• technical data
• curves (QH, Eta, P1, P2, etc.) which can be adapted to the
density and viscosity of the pumped liquid and show the
number of pumps in operation
• product photos
• dimensional drawings
• wiring diagrams
• quotation texts, etc.
Literature
This section contains all the latest documents of a given pump,
such as
• data booklets
• installation and operating instructions
• service documentation, such as Service kit catalogue and
Service kit instructions
• quick guides
• product brochures.
Service
This section contains an easy-to-use interactive service
catalogue. Here you can find and identify service parts of both
existing and discontinued Grundfos pumps.
Furthermore, the section contains service videos showing you
how to replace service parts.
18
5
Sizing
0
Further product documentation
Vaccuperm VGS-140
1
This section is based on different fields of application and
installation examples and gives easy step-by-step instructions in
how to size a product:
• Select the most suitable and efficient pump for your
installation.
• Carry out advanced calculations based on energy,
consumption, payback periods, load profiles, life cycle costs,
etc.
• Analyse your selected pump via the built-in life cycle cost tool.
• Determine the flow velocity in wastewater applications, etc.
Replacement
In this section you find a guide to selecting and comparing
replacement data of an installed pump in order to replace the
pump with a more efficient Grundfos pump.
The section contains replacement data of a wide range of pumps
produced by other manufacturers than Grundfos.
Based on an easy step-by-step guide, you can compare
Grundfos pumps with the one you have installed on your site.
When you have specified the installed pump, the guide will
suggest a number of Grundfos pumps which can improve both
comfort and efficiency.
CAD drawings
In this section, it is possible to download 2-dimensional (2D) and
3-dimensional (3D) CAD drawings of most Grundfos pumps.
These formats are available in WebCAPS:
2-dimensional drawings:
• .dxf, wireframe drawings
• .dwg, wireframe drawings.
3-dimensional drawings:
• .dwg, wireframe drawings (without surfaces)
• .stp, solid drawings (with surfaces)
• .eprt, E-drawings.
WinCAPS
WinCAPS is a Windows-based Computer Aided
Product Selection program containing detailed
information on more than 220,000 Grundfos products
in more than 30 languages.
The program contains the same features and functions
as WebCAPS, but is an ideal solution if no internet
connection is available.
WinCAPS is available on DVD and updated once a
year.
Fig. 19 WinCAPS DVD
Subject to alterations.
19
Being responsible is our foundation
Thinking ahead makes it possible
Innovation is the essence
95719030 0812
ECM: 1062502
GRUNDFOS A/S . DK-8850 Bjerringbro . Denmark
Telephone: +45 87 50 14 00
www.grundfos.com
The name Grundfos, the Grundfos logo, and the payoff Be–Think–Innovate are registrated trademarks
owned by Grundfos Management A/S or Grundfos A/S, Denmark. All rights reserved worldwide.