Add to collection(s) Add to saved
  1. Science
  2. Earth Science
  3. Geology

List 1 Approved Steelmakers and Manufacturers of

List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
This list identifies works approved by Lloyd’s Register Group Limited (LR) for steelmaking
and the manufacture of rolled steel plate, strip, sections and bars in accordance with the
requirements of LR's Rules for the Manufacture, Testing and Certification of Materials,
Chapter 3.
The information listed for each works is a summary of the product, generic grade and
maximum thickness, or in the case of round bars, diameter approved.
It is important to note that this list does not provide full details of the grades approved by
LR as required by the Rules. The combinations of deoxidation practice (e.g. killed,
semi-killed), micro-alloying and grain refining additions (e.g. Al, Al + Nb Al + Nb + V,
etc.), in association with specific rolling procedures ( e.g. N or TM, etc.), are not included.
These parameters may vary within each grade by manufacturer and could influence the
fabrication procedures that can be applied.
The list also includes firms approved for the manufacture of fabricated steel sections.
Where required this information should be obtained from the current certificate of approval
issued to the manufacturer by LR.
Works designated "MQS Approved" are also approved under the Materials Quality Scheme
in accordance with LR's Rules for the Manufacture, Testing and Certification of Materials,
Chapter 1 Section 2.
Approval only covers the manufacturing location listed, it does not extend to other works
owned by the same company. The local LR surveying office is also listed.
Abbreviations:
B.O.S.
Con Cast
E.A.F.
O.H.
Basic Oxygen Steelmaking
Continuous Casting
Electric Arc Furnace
Open Hearth
Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers,
employees or agents are, individually and collectively, referred to in this clause as 'Lloyd's
Register'. Lloyd's Register assumes no responsibility and shall not be liable to any person
for any loss, damage or expense caused by reliance on the information or advice in this
document or howsoever provided, unless that person has signed a contract with the
relevant Lloyd's Register entity for the provision of this information or advice and in that
case any responsibility or liability is exclusively on the terms and conditions set out in that
contract.
As at 06 September 2016
© Lloyd’s Register Group Limited 2016. All rights reserved.
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Sydney
Steelmaking
Plates
B.O.S. / Con Cast
Normal Strength
Higher Strength
Hot Rolled Coil
Normal Strength
Higher Strength
As below
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
Australia
BLUESCOPE STEEL (AIS) PTY. LTD.
51
51
13
6
Port Kembla Steelworks
P.O. Box 1854
Wollongong
NSW 2500
Tel: +61 2 42754666 Fax: +61 2 42753045
Email: nigel.attwell@bluescopesteel.com
Plates with specified through thickness properties notation Z35 may be added.
Normalizing heat treatments carried out by sub-contractor, Bisalloy.
Certificate # MD00/1929/0009/1 Expiry date: 28/07/2018
Austria
BREITENFELD EDELSTAHL AG
Vienna
Steelmaking
Semi-Finished
E.A.F./V.O.D./Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless
120
Steelmaking
Bars
E.A.F./Ingot/Con Cast
Structural
As below
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless
220
Breitenfelderstrasse 22
8662 St. Barbara im Mürztal
Tel: +43 (0)3858 6161 231 Fax +43 (0)3858 6161 248
Email mailto:marina.paller@breitenfeld.at
Web: http://www.breitenfeld.at
Certificate # MD00/3255/0005/1 Expiry Date: 06/06/2018
Including VD/VOD
BÖHLER EDELSTAHL GmbH
Vienna
Mariazellerstraße 25
Postfach 96
A-8605 Kapfenberg
Tel: +43 3862 20 37063 Fax: +43 3862 20 37559 Email: mailto:walter.wolflehner@bohler-edelstahl.at Web:http://www.bohler-edelstahl.com
Certificate #: MD00/0200/0008/1 Expiry date: 21/01/2018
BÖHLER PROFIL GmbH
Vienna
Sections
Normal Strength
Higher Strength
Normal Strength
Higher Strength
Structural
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless
20
20
20
20
20
Steelmaking
Semi-Finished
VAR/INGOT
Ingots (tonnes)
38
38
ESR
Ingots
As below
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless
carbon, carbon-manganese, alloy, austenitic
stainless, duplex
Bars
Normal Strength
Structural
Machinery
Bars
Waidhofnerstraße 8
3333 Böhlerwerk
Tel: +43 7448 7007 24504 Fax: +43 7448 7007 24602
email: herwig.kohlreiter@bohler-profil.com web: www.bohler-profil.com
Certificate #: MD00/0202/0007/1 Expiry date: 27/01/2018
High alloy bars and sections may be accepted for approved applications.
SONDERSTAHLWERK BREITENFELD GmbH
Vienna
38
Breitenfelderstasse 22
8662 St. Barbara im Mürtztal
Tel +43 (0)3858 6161 231 Fax +43 (0)3858 6161 248
Email marina.paller@breitenfeld.at Web http://www.breitenfeld.at
Certificate # MD00/3256/0005/1 Expiry date: 06/06/2018
Including remelting of Ni materials
STAHL JUDENBURG GmbH
Vienna
A
carbon, carbon-manganese
carbon, carbon-manganese, carbon-manganese
120
120
120
Gußstahlwerkstrasse 21
A-8750 Judenburg
Tel: +43 3572 701-358 Fax: +43 3572 701-248 Email: mailto:christian.sunnitsch@stj.at
Certificate #: MD00/1643/0007/1 Expiry date: 28/01/2018
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
Web: http://www.stahl-judenburg.com
2
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
VOESTALPINE STAHL DONAWITZ GmbH
Vienna
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Blooms/Billets
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
Max Thickness/Diameter (mm)
283
Kerpelystraße 199
A 8700 Leoben
Tel: +43 50304 25-4659 Fax: +43 50304 65-2464 Email: mailto:karin.rockenschaub@voestalpine.com Web:http://www.voestalpine.com/stahldonawitz
Certificate #: MD00/2976/0005/1 Expiry date: 20/04/2018
voestalpine Grobblech GmbH
Vienna
Steelmaking
Plates
B.O.S. / Con Cast
Normal Strength
Higher Strength
Clad
As below
A, B, D, E
AH42, DH42, EH42
AH40, DH40, EH40, FH40
AH32, AH36, DH32, DH36, EH32, EH36, FH32,
FH36
360AR
410AR
360FG, 410FG, 460FG, 490FG, 510FG
1.5Ni, 3.5Ni, 5Ni, 9Ni
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,
LTEH36, LTFH32, LTFH36
D/304L
Steelmaking
E.A.F./V.O.D./Con Cast
As below
Semi-Finished
Rolled Billets
Carbon, Carbon-Manganese
140
Billets
carbon, carbon-manganese, Normal Strength
300
Steelmaking
Semi-Finished
E.A.F./A.O.D./Con Cast
Slabs
As below
austenitic stainless
200
Steelmaking
Semi-Finished
Plates
E.A.F./A.O.D./Con Cast
E.A.F./V.O.D./Con Cast
Slabs
Austenitic Stainless
austenitic stainless
austenitic stainless
austenitic stainless
304L, 304LN, 316L, 316LN, 321, 347
200
14
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Blooms
As below
carbon, carbon-manganese, alloy, Ferritic
Stainless Steel*
Boiler & Pressure Vessel
Ferritic Low Temperature
140
55
100
140
40
50
140
50
140
50
P.O Box 3
Voest.- Alpine - Str. 3
A-4020 Linz
Tel: +43 50304 15 9091 Fax: +43 50304 55 9091
Email: mailto:ronald.lachmair@voestalpine.com Web: www.voestalpine.com
Certifcate No. MD00/1614/0009/1 Expiry date: 29/07/2017
Approval includes the supply of z25 and z35 grades.
Approval includes pressed heads.
Belarus, Republic of
OJSC "Byelorussian Steel Works-Management
Company of
St. Petersburg
"Byelorussian Metallurgical Company" holding"
(OJSC "BSW -management company of "BMC" holding")
37, Promyshlennaya Str.
BY- 247210 Zhlobin,
Gomel Region,
Tel No: +375 2334 56180 Fax no: +375 2334 56317 Mob +375 291105030
Email : mailo:nb.ouk@bmz.gomel.by
Web: xxxxxxxxxxxxxxxx
Certificate No: MD00/4297/0001/1 Expiry date 05/03/2017
Belgium
APERAM STAINLESS BELGIUM - CHATELET site
Antwerp
14, Rue des Ateliers
6200 Chatelet
Tel: +32 (0) 7160 7792
Email: fabric.vanmeerhaeghe@aperam.com
Web: http://www.aperam.com
Certificate Number: MD00/4387/0002/1 Expiry: 17/09/2017
APERAM STAINLESS STEEL EUROPE- Genk site
Antwerp
Swinnenwijerweg 5
B-3600 Genk
Tel: +32 89 30 25 68
Web: http://www.aperam.com
Email: stefaan.maes@aperam.com
Certificate #: MD00/3423/0004/1 Expiry date: 28/01/2017
ESB sprl
Antwerp
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
3
600
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
ENGINEERING STEEL BELGIUM
Rue de l'Environnement, 8
B - 4100
Seraing
Tel No: +32 4 33 885 60
Fax No: +32 4 33 809 00
Email : dtroisfontaines@esb.be
Web : www.esb.be
Certificate No: MD00/3858/0002/1 Expiry date: 09/11/2016
Materials Suitable for Steel Forgings, Pipe and Tube, Ingots up to 800mm diameter and Blooms up to 600 mm diameter
INDUSTEEL BELGIUM SA
Antwerp
Steelmaking
Plates
E.A.F. / Con Cast
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
Austenitic Stainless
Duplex Stainless
As below
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36, EH40
DH42, DH46, DH50, DH55, DH62, DH69, EH42,
EH46, EH50, EH55, EH62, EH69, FH42, FH46,
FH50, FH55, FH62, FH69
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,
LTEH36, 5Ni, 9Ni
304L, 304LN, 316L, 316LN
UNS S31803(MOD)*
50
50
100
40
50
50
50
40
ARCELOR MITTAL GROUP
266, Rue de Châtelet
B-6030 Charleroi
Tel: +32 71 44 14 51 Fax: +32 71 44 19 29 Email: mailto:patrick.malgre@arcelormittal.com Web: http://www.arcelormittal.com
Plates in grades LTAH32; LTAH36; LTDH32; LTDH36; LTEH32; LTEH36; 5%Ni; 9%Ni over 40mm thickness and up to the maximum thickness stated above are
accepted for approved applications only.
* accepted for approved applications.
Higher strength grades supplied in the quenched and tempered grades are accepted with specified through thickness properties designation Z35.
Certificate Number: MD00/0477/0010/1 Expiry: 08/07/2017
NLMK CLABECQ S.A.
Antwerp
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
360, 410
360FG, 410FG, 460FG, 490FG, 510FG
120
120
25
50
120
Rue de Clabecq, 101
B-1460 Ittre
Tel: +32 3919227 Fax: +32 3919883 Mobile +33 4972 297369
Email:j.vermeulen@eu.nlmk.com
Web:http://www.eu.nlmk.com
MQS Approved - Approval No. MQS016
Certificate #: MD00/2204/0012/1 Expiry date: 23.06.2018
Brazil
ARCELORMITTAL BRAZIL S/A (ARCELORMITTAL
TUBARÃO )
Rio de Janeiro
Steelmaking
B.O.S. / Con Cast
carbon, carbon-manganese
Semi-Finished
Slabs
carbon, carbon-manganese
Hot Rolled Coil
Normal Strength
D
16
A, B
19
Higher Strength
AH27S, AH32
16
Boiler & Pressure Vessel
460FG, 490FG
16
360FG, 410FG
19
250
Av. Brigadeiro Eduardo Gomes,
930 - Jardim Limoeiro
29164-970 Serra E.S
Carbon and carbon-manganese grades cover the following LR normal and higher tensile strength grades. A, B, D, E, AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
Tel: +55 27 3348 3215 Fax: +55 27 3348 2211 Mobile: +55 27 9992 1227
Email : mailto:marcelopr@terra.com.br
Web: http://www.arcelormittal.com/br/tubarao
Material Quality Scheme approved, MQS 054
Certificate #: MD00/0342/0010/1 Expiry date: 29/06/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
4
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
GERDAU AÇOMINAS S.A.
Rio de Janeiro
Steelmaking
Semi-Finished
B.O.S./Ingot/Con Cast
Rolled Billets
Slabs
Blooms
Billets
Rolled Blooms
Normal Strength
As below
Carbon, Carbon-Manganese, Alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
Carbon, Carbon-Manganese, Alloy
A
B.O.S. / Con Cast
Normal Strength
Higher Strength
As below
A, B, D, E
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
A
360, 410
Hot Rolled Coil
Max Thickness/Diameter (mm)
180
250
300
180
280
20
Rodovia MG-443 KM 7
Fazenda do Cadete
36420-000-Ouro Branco-MG
Tel: +55 32 3749 3339
email: luiz.araujo@gerdau.com.br web www.gerdau.com.br
Certificate #: MD00/2071/0008/1 Expiry date: 25/02/2018
USIMINAS
Rio de Janeiro
Steelmaking
Plates
Boiler & Pressure Vessel
Hot Rolled Coil
Normal Strength
Boiler & Pressure Vessel
50
50
40
50
12
12
Usinas Siderúrgicas de Minas Gerais S/A
Usina Intendente Câmera
Av. Pedro Linhares Gomes, 5431
Distrito Usiminas, CEP 35160-900
Ipatinga, Minas Gerais
Tel +55 (0)31 38293136 Fax +55 (0)31 38293516 Email: mailto:ssampaio@usiminas.com.br
Z25 and Z35 through thickness properties for plates of approved grades in the TM+Acc and TM+Acc+Temper conditions
Materials Quality Scheme Approved - MQS014
Certificate #: MD00/1603/0009/1 Expiry date: 23/06/2017
USINAS SIDERÚRGICAS DE MINAS GERAIS S.A. USIMINAS
São Paulo
Steelmaking
B.O.S. / Con Cast
As below
Plates
Normal Strength
A, B, D, E
80
Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
80
40
360FG, 410FG, 460FG, 490FG, 510FG
80
Boiler & Pressure Vessel
Rodovia Cônego Domênico Rangoni, Km 6
Vila da Indústrias 11573-900
Cubatão - São Paulo
Tel: +55 13 3362-2978 Fax: +55 13 3362-3775 Email: mailto: takayochi.ueno@usiminas.com Web:http://www.usiminas.com
Specified through thickness properties for plates in the normalised condition, rolled from ingots, up to 35 mm thickness.
Specified through thickness properties for plates of grades up to DH32 and thickness up to 26mm in the normalised condition, rolled from continuously cast
slab.
Material Quality Scheme approved, MQS 044
Certificate #: MD00/1193/0009/1 Expiry date: 28/09/2017
Bulgaria
RADOMIR METAL INDUSTRIES JSC
Sofia
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
carbon, carbon-manganese
carbon, carbon-manganese
E.A.F. / Con Cast
Blooms/Billets
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
As below
A
AH27S, AH32, AH36, DH27S, DH32, DH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
25
2400 Radomir,
Tel: 359 77780489 Fax: 359 77782134
email: rmindustries@mbox.contact.bg web: radomir-metal-industries.com
Certificate No: MD00/4386/0001/1 Expiry Date: 17/09/2017
STOMANA INDUSTRY AD
Sofia
Steelmaking
Semi-Finished
Plates
200
40
40
25
40
1, Vladaysko Vastanie Str.
2304 Pernik
Tel: +359 766 81028 Fax: +359 766 81952
email:vsofteva@stomana.bg web: www.stomana.bg
Certificate #: MD00/1868/0010/1 Expiry date: 16/04/2019
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
5
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Toronto
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
carbon, carbon-manganese
D, E
A, B
AH32, AH36, DH32, DH36, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG
205
50
60
65
65
EAF/LMF/Con Cast
Slabs
As Below
A, B, AH36, DH36
200
Canada
ESSAR STEEL ALGOMA INC.
105 West Street
Sault Ste. Marie
Ontario
P6A 5P2
Tel +1 705 945 2347 Fax: +1 705 945 2632
e-mail: lori.pilot@algoma.com web: www.essarsteelalgoma.com
Certificate #: MD00/0092/0008/1 Expiry date: 05/05/2017
EVRAZ NORTH AMERICA
Vancouver BC
Steelmaking
Semi-Finished
EVRAZ Regina Steel
100 Armour Road
Regina, SK
S4P 3C7
Tel: +1 800 667 1616 and 306 924 7500 Email to: steelplate@evrazna.com Web: http://www.evrazna.com
Slabs as semi-finished products of nominal dimensions 8" x 84" x 480" are approved
MATERIALS QUALITY SCHEME APPROVED - MQS 055
Certificate No. :MD00/4490/0001/1 Expiry Date: 16/6/2018:
GERDAU LONG STEEL NORTH AMERICA
Toronto
Steelmaking
Sections
E.A.F. / Con Cast
Normal Strength
As below
A
26
E.A.F. / Con Cast
Normal Strength
Higher Strength
As below
A, B
AH27S, AH32, AH36
15
15
CAMBRIDGE MILL
160 Orion Place,
Cambridge,
Ontario,
N1T 1R9
Tel: +1 519 740 2488 ext 1420 Fax: +1 519 623 2062
email: maryam.chamaneh@gerdau.com web: www.gerdaul.com/longsteel
Certificate #: MD00/3046/0004/1 Expiry date: 31/01/2016
GERDAU LONGSTEEL NORTH AMERICA
Toronto
Steelmaking
Sections
Whitby Steel Mill Operations
1801 Hopkin Street South
Whitby
Ontario
L1N 5T1
Tel: +1 905 668 8811 ext 2049 Fax: +1 905 668 9361
Email: mailto:leonardo.nunees@gerdau.com
Web: http://www.gerdau.com/longsteel
Certificate #: MD00/0322/0008/1 Expiry date: 31/01/2017
CSA grades 260W, 300W and 350W may be accepteed for approved applications equivalent to the appropriate Lloyds Register grade above
China, People's Republic of
ANGANG STEEL COMPANY LIMITED
Dalian
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
A, B, D, E
AH42, AH46, AH50, AH55, DH42, DH46, DH50,
DH55, EH42, EH46, EH50, EH55, FH42, FH46,
FH50, FH55
AH27S, AH32, AH36, DH27S, DH32, DH36,
DH40, EH27S, EH32, EH36, EH40, FH27S, FH32,
FH36, FH40
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36, 1.5Ni, 3.5Ni, 5Ni,
9Ni
100
80
100
40
50
40
HEAVY PLATE MILL OF MEDIUM AND HEAVY PLATE PLANT
Honqi Road, Lishan District,
Anshan City,
Liaoning Province
Tel: +86 412 673 4836 Fax: +86 412 672 5766 Email mailto:hp318@sina.com Web http://www.ansteel.con.cn
All grades and thicknesses accepted with specified through thickness properties, Z25 and Z35 designations.
Certificate Number: MD00/1869/0010/1 Expiry: 22/03/2018
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
6
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
ANGANG STEEL COMPANY LIMITED
Dalian
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
Normal strength, Higher Strength
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
Max Thickness/Diameter (mm)
300
40
40
20
40
MEDIUM PLATE MILL OF MEDIUM AND HEAVY PLATE PLANT
Angang Area
Anshan City
Liaoning Province
Tel +86 0412 675 1030 Fax +86 0412 675 2819 Email mailto:zy-zb-111@163.com
Slabs as semi finished products nominal 2000mm width x nominal 7000mm length to the above maximum thickness are approved.
Certificate No. MD00/2757/0008/1 Expiry date: 22/10/2017
ANGANG STEEL COMPANY LIMITED
Dalian
Hot Rolled Coil
Normal Strength
Higher Strength
Boiler & Pressure Vessel
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG
20
20
20
HOT STRIP MILL OF ANGANG STEEL COMPANY LIMITED
Angang Production Area,Tiexi District
114024
Tel: +86 412 6757143 Fax: +86 412 6753575
Email: agwanrui@163.com
Web http://www.ansteel.com.cn
Certificate #: MD00/3301/0004/1 Expiry date: 01/01/2019
ANGANG STEEL COMPANY LIMITED
Dalian
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Blooms/Billets
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
As below
carbon-manganese, carbon, carbon manganese
A, B, D, E
AH32, AH36, AH40, DH32, DH36, DH40, EH32,
EH36, EH40
360FG, 410FG, 460FG, 490FG, 510FG
5Ni, 9Ni
E.A.F./V.O.D./Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy
300
100
100
40
60
BAYUQUAN 5500 HEAVY PLATE MILL
115000 Bayuquan
Yingkou City
Liaoning Province
Tel: +86 417 8680153 Fax: +86 417 8680141
email: liuyuan1360@163.com web: www.ansteel.com.cn
Certificate No. MD00/3595/0004/1 Expiry date: 09/05/2018
ANSTEEL STEEL CASTING CO., LTD.
Dalian
Steelmaking
Semi-Finished
100
West Side of Hongqi Road
Anshan, Liaoning Province
11042
el: +86 412 6765212/6765217 Fax: +86 412 6765218
Email to: ajk999@yahoo.com.cn Web http://www.angangzhongji.com.cn
Certificate #: MD00/4463/0001/1 Expiry date: 25/02/2018
ANYANG IRON & STEEL CO., LTD.
Wuhan
Steelmaking
Semi-Finished
Plates
B.O.S./E.A.F./Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Sections
Normal Strength
As Below
Normal strength
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
360AR, 410AR, 460FG, 490FG, 510FG
360FG, 410FG
A, B
230
40
36
36
40
12
Yindu District
Anyang City
Henan Province
Tel: +86 372 3120051 Fax: +86 372 3120177
email: 343062385@163.com web: www.anyang.com.cn
Certificate #: MD00/2200/0010/1 Expiry date: 18/01/2019
A, B and D grades in the normalised condition approved for through thickness properties with Z25 and Z35 notation.
BAOSHAN IRON & STEEL CO., LTD.
Shanghai Port
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
B.O.S. / Ingot
Slabs
Blooms/Billets
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
7
As below
As below
carbon, carbon-manganese
carbon, carbon-manganese, Alloy
A, B, D, E
AH40, DH40, EH40, FH27S, FH32, FH36
DH36S
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
AH42, AH46, AH50, AH55, AH62, AH69, DH42,
DH46, DH50, DH55, DH62, DH69, EH42, EH46,
EH50, EH55, EH62, EH69, FH40, FH42, FH46,
FH50, FH55, FH62, FH69
360FG, 410FG, 460FG, 490FG, 510FG
LTAH40, LTDH40, LTEH40, LTFH27S, LTFH32,
LTFH36, LTFH40
500
500
130
68
90
100
160
100
68
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Shanghai Port
Plates
Ferritic Low Temperature
Hot Rolled Coil
Normal Strength
Higher Strength
Boiler & Pressure Vessel
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36
A, B, D
AH32, AH36
460FG, 490FG, 510FG
360FG, 410FG
22
12
12
22
14
14
China, People's Republic of
BAOSHAN IRON & STEEL CO., LTD.
80
Core Base
No 885, Fujin Road
Baoshan District
Shanghai 201900
Tel +86 21 2664 5085
Fax +86 21 2664 4886
E-mail: zhangxiangkui@baosteel.com
Web:http://www.baosteel.com
Including all plate grades and thicknesses with specified through thickness properties (Z35)
Certificate #: MD00/1343/0017/1 Expiry date: 29/03/2019
Materials Quality Scheme Approved - MQS 038
CHANGSHU LONGTENG SPECIAL STEEL CO., LTD. Jiangyin
Sections
Normal Strength
Higher Strength
A, B, D
AH27S, AH32, AH36
Steelmaking
B.O.S. / Con Cast
E.A.F. / Con Cast
Ingots (tonnes)
Blooms
Billets
Normal Strength
As below
As below
carbon, carbon-manganese, alloy
Normal Strength, Higher Strength
Normal Strength, Higher Strength
D
E
A, B
DH32, DH36, EH32, EH36
AH27S, AH32, AH36
26
260
200
15
16
20
16
20
200
90
No. 9 Jusha Road
Meili Town
Changshu City
Jiangsu Province 21551
Tel: +86 0512 5206 1085 Fax: +86 0512 5266 1141
Email: lttg@lttg.cn Web: http://www.lttg.cn
Certificate #: MD00/3275/0005/1 Expiry date: 09/10/2018
CHANGSHU LONGTENG SPECIAL STEEL CO., LTD. Jiangyin
Semi-Finished
Sections
Higher Strength
118 Hualian Road,
Tonggang Industrial Park,
Meili Town, Changshu City,
Jiangsu Province 215511
Tel.:+86 0512 5206 1085 Fax.: +86 512 5266 1141
Email: lttg@lttg.cn Web: http://www.lttg.cn
Certificate #: MD00/3976/0003/1 Expiry date: 07/12/2017
Blooms as semi finished products nominal 340mm width x nominal 12000mm length
Billet approval covers BOS/Concast billets to 200 x 310mm section size x 6000mm nominal length..
CHENGDE JIANLONG SPECIAL STEEL CO., LTD.
Qingdao
Steelmaking
Semi-Finished
Bars
B.O.S. / Con Cast
Blooms/Billets
Chain Cable Stock
As below
carbon, carbon-manganese, Alloy
U2, U3
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
As below
Normal strength, Higher Strength
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR, 460AR
360FG, 410FG, 460FG, 490FG
Ping-an-bao Town
Xinglong County
Chengde, Hebei
Tel.:+86 0314 5316388 Fax.: +86 314 5316389
Email: yangdong@ejianlong.com Web: http://www.ejianlong.com
Certificate #: MD00/4550/0002/1 Expiry date: 10/02/2019
CISCO
Wuhan
Boiler & Pressure Vessel
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
8
300
80
80
40
80
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Plates
Normal Strength
Higher Strength
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR, 360FG, 410FG, 460FG, 490FG,
510FG
Chongqing Iron and Steel Co., Ltd.
Jiangnan Town (4100 Mill)
Changshou District
Chongqing
Tel: +86 23 6887 3543 Fax: +86 23 6887 3543
email: zyflwy@163.com web: www.cqgt.com
Certificate Number: MD00/3763/0007/1 Expiry date: 27/03/2019
CISCO
Wuhan
Boiler & Pressure Vessel
40
40
40
Chongqing Iron and Steel Co., Ltd.
Jiangnan Town (2700 Mill)
Tel: +82 623 6887 3543 Fax: +82 623 6887 3543
Email: cqgt@163.com Web: http://www.cqgt.cn
Plates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied to all Grades and supply conditions.
Certificate Number: MD00/3982/0003/1 Expiry: 25/01/2018
DAYE SPECIAL STEEL CO., LTD.
Wuhan
Steelmaking
Semi-Finished
Bars
B.O.S. / Con Cast
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Billets
Bars
Structural
Machinery
Chain Cable Stock
As below
As below
carbon, carbon-manganese,
carbon, carbon-manganese,
carbon, carbon-manganese,
carbon, carbon-manganese
carbon, carbon-manganese,
U1, U2, API-2F
U3, R3S, R4
alloy
alloy
alloy
alloy
40
410
650
190
250
110
160
316 Huangshi Avenue
Huangshi City
Hubei Province
Post code: 435001
Tel: +86 714 629 7888 Fax: +86 714 629 7781
Email: chenlei7483@163.com Web: http://www.dayesteel.com.cn
Mooring grade bars (grade R4) are restricted in ingot cast condition to supply to Zhengmao Group Co., Ltd.
Mooring grade bars (grade R3S) are restricted to supply to Foshan Marine Anchor Chain Ltd. (FMAC)
The bars may supply in annealing, normalized or quench and temperted conditions when it is appropriate
Certificate Number: MD00/2493/0009/1 Expiry: 12/08/2017
DONGBEI SPECIAL STEEL GROUP
Dalian
Steelmaking
B.O.S. / Con Cast
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Blooms/Billets
Bars
Structural
Chain Cable Stock
carbon, carbon-manganese, alloy
carbon, carbon-manganese
carbon, carbon-manganese
carbon, carbon-manganese
carbon, carbon-manganese
carbon, carbon-manganese
U1, U2, U3
Steelmaking
Semi-Finished
EAF/LRF/VD/Ingot
Ingots (tonnes)
Carbon, Carbon-manganese, Alloy
carbon, carbon-manganese, alloy
Steelmaking
B.O.S. / Con Cast
As below
Semi-Finished
Slabs
Normal strength, Higher Strength
Plates
Normal Strength
A, B
36
Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36
30
Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG
30
360, 410
36
Semi-Finished
Bars
5
450
200
200
130
BEIMEN SPECIAL STEEL CO., LTD.
Fularji District
Qiqihar City
Heilongjiang Province
Tel: +86 452 680 1271 Fax: +86 452 680 1234
email: bmtgjsb@163.com web: bg.bmsteel.com
Certificate No: MD00/2907/0002/1 Expiry date: 29/07/2017
DONGBEI SPECIAL STEEL GROUP
Dalian
27
27
FUSHUN SPECIAL STEEL CO. LTD.,
East No 8 Anshan Road,
Wanghua District,
Fushun City,
Liaoning Province
Tel No: +86 413 668 9161-3668 Fax no: +86 413 6674090
Web: www.dtsteel.com
Certificate No MD00/3945/0002/1 Expiry date: 05/09/2017
FUJIAN PROVINCIAL SANSTEEL (GROUP) CO.,
LTD.
Guangzhou
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
9
250
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Steelmaking
Plates
Hot Rolled Coil
B.O.S. / Con Cast
Normal Strength
Higher Strength
Normal Strength
As below
A, B
AH27S, AH32, AH36
A, B
Steelmaking
B.O.S. / Con Cast
As below
Semi-Finished
Slabs
Normal strength, Higher Strength
Hot Rolled Coil
Normal Strength
A, B, D
18
Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36
18
Normal Strength
A, B, D
18
Higher Strength
AH27S, DH27S, AH32, DH32, AH36, DH36
18
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
As below
Normal strength, Higher Strength
A, B, D, E
AH27S, DH27S, EH27S
AH32, AH36, DH32, DH36, EH32, EH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
Middle Gongyezhong Road
Meilie District
Sanming City
Fujian Province
Tel: +86 598 8205138 Fax: +86 598 8205435
Email: hic099@126.com
Web: www.fjsg.com.cn
Certificate #: MD00/3587/0005/1 Expiry date: 26/04/2018
GUANGXI LIUZHOU
Guangzhou
36
36
12
IRON & STEEL (GROUP) COMPANY
117 Beique
Liuzhou
Guangxi
Tel: +86 (0)772 2596593 Fax: +86 (0)772 2592784
email pzkkz@126.com web www.liuzousteel.com
Certificate #: MD00/2632/0007/1 Expiry date: 01/01/2018
HANBAO IRON & STEEL CO. LTD (HANSTEEL
GROUP)
Wuhan
Plates from coils
250
232,Fuxing Road,
Handan,
Hebei. 056015
Tel +86 310 6073275
Fax No. + 86 310 6072241
Email jiashibo@mail.hgjt.cn
Web www.hgjt.com.cn
Certificate No MD00/3874/0002/ 1 Expiry Date 09/01/2017
HEBEI IRON & STEEL CO., LTD.
Qingdao
Steelmaking
Semi-Finished
Plates
Boiler & Pressure Vessel
220
50
38
50
25
50
Handan Branch
232 Fuxing Road
Handan City
Hebei Province
056015
Tel: +86 310 607 2202 Fax: +86 310 607 2241
Email: longzhengmin@163.com Web: http://www.hgjt.com.cn
Slabs as semi-finished products nominal 1800mm width x nominal 3200mm length to the above maximum thickness.
Plates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied for approved grades supplied in the normalized condition
Certificate Number: MD00/1970/0010/1 Expiry: 03/03/2019
HEBEI JINGYE CUT DEAL CO., LTD.
Qingdao
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
Normal strength, Higher Strength
A, B, D
AH27S, AH32, AH36, DH32, DH36
360FG, 410FG, 460FG, 490FG, 510FG
220
220
30
30
30
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Billets
As below
carbon, carbon-manganese, alloy
800
Nandian Town
Pingshan County
Shijiazhuang City
Hebei Province
Tel No +86 311 8287 3953 Fax No +86 311 82873988
Mob +86 158 3111 8888
Email jingye@hbjyjt.com
Web www.hbjyjt.com
Certificate No MD00/4022/0002/1 Expiry Date 08/05/2018
HENGYANG VALIN STEEL TUBE CO., LTD.
Wuhan
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
10
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
No. 10 Dalixincun
Hengyang City
Hunan Province 421001
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Steelmaking
B.O.S. / Con Cast
As below
Semi-Finished
Slabs
carbon, carbon-manganese
Hot Rolled Coil
Normal Strength
A, B, D
25
Plates from coils
Normal Strength
A, B, D
25
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy
Tel: +86 734 8872188 Fax: +86 734 8873188
Email: hgscjf@163.com
Web: www.hysteeltube.com
Certificate #: MD00/3098/0003/1 Expiry date: 04/08/2019
HUNAN VALIN LIANYUAN IRON & STEEL CO.,
LTD.
Wuhan
230
Huangnitang, Loudi
Hunan Province
Post Code: 417009
Tel +738 8661473 Fax +7388663570
Email: pmy@lysteel.com
web: www. lysteel.com
Certificate #: MD00/3999/0002/1 Expiry date: 05/03/2018
INNER MONGOLIA NORTH
Wuhan
8
HEAVY INDUSTRIES GROUP CO., LTD.
Binggong Road, Qingshan District
Baotou City
Inner Mongolia
014033
Tel No:+86 742 338 6297
Fax No: +86 742 334 0042
Email: bfzg-tsgs@163.com
Web http://www.bfzg.com
Including semi-finished as-forged bars to 8.5 tonnes in carbon, carbon-manganese and alloy steel for further process of forge
Certificate No: MD00/3099/0005/1 Expiry date: 07/08/2016
JIANGSU JIEDA SPECIFIC NEW MATERIAL CO LTD Jiangyin
Jiangyin Plant
No. 88-98 Gangcheng Road, Shengang Industrial Park
Lingang New City Development Zone,
Jiangyin City, Jiangsu Province. 214400
Seamless Hollow
Structural Sections
carbon
20
Steelmaking
B.O.S. / Con Cast
E.A.F. / Con Cast
Blooms
Billets
Bars
Structural
Machinery
Chain Cable Stock
As below
As below
carbon, carbon-manganese
carbon, carbon-manganese
carbon, carbon-manganese
carbon, carbon-manganese
carbon, carbon-manganese
U2
U3
Tel No: + 00 86-510-8668775
Fax No: + 00 86-510-86687775/+00 510-86687229
Email: chezhongnan@jsjieda.com
Website: www.jsjieda.com
Certificate No. MD00/4442/0001/01
JIANGSU SHAGANG GROUP
Expiry Date: 18/01/2018
Nanjing
Semi-Finished
Bars
200
150
500
100
100
140
210
HUAIGANG SPECIAL STEEL CO., LTD
No. 188 South Xi'an Road
Huai'an City
Jiangsu Province
Tel: +81 517 83033307 Fax: +81 517 83033307 Mobile: +861536590 1758
Email:sundawen@163.com
The approval for rolled bars over 60mm diameter is for steel manufactured by the B.O.S. / Con Cast route.
Bars for chain cable stock are intended for final heat treated conditions; Grade U2 normalized; Grade U3 quenched and tempered.
Chain cable stock bars may be accepted up to 250mm diameter may be accepted for further processing for forged chain cable fittings.
Blooms, billets and bars as semi finished-products are approved for further processing for rolled products; blooms nominal maximum width 200mm x nominal
maximum length 12000mm; billets nominal maximum width 150mm x nominal maximum length 12000mm; bars nominal maximum length 12000mm; to the
above maximum thicknesses.
Certificate Number: MD00/3240/0005/1 Expiry: 13/06/2015
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
11
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
JIANGSU SHAGANG GROUP CO., LTD
Jiangyin
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Slabs
As below
carbon, carbon-manganese
Max Thickness/Diameter (mm)
320
Hongfa Steel Plant
Steelmaking Plant Number 1
Jinfeng Town
Zhangjiagang City
Jiangsu Province 215625
Tel: +86 512 5856 8791 Fax: +86 512 5855 8900 Email mailto: ctoec@shagang.cn Web http://www.sha-steel.com
Approval covers for con cast slabs to nominal sizes 2065mm wide x 9000mm long to the above maximum thickness for further processing for rolled products.
Certifcate Number: MD00/3127/0007/1 Expiry date: 27/10/2016
JIANGSU SHAGANG GROUP CO., LTD
Jiangyin
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
A, B, D, E
AH27S, AH32, AH36, AH40, AH42, AH46,
AH50, AH55, AH62, AH69, DH27S, DH32,
DH36, DH40, DH42, DH46, DH50, DH55, DH62,
DH69, EH27S, EH32, EH36, EH40, EH42, EH46,
EH50, EH55, EH62, EH69, FH27S, FH32, FH36,
FH40, FH42, FH46, FH50, FH55, FH62, FH69
360AR, 410AR, 460AR
360FG, 410FG, 460FG, 490FG, 510FG
100
100
40
100
Hongfa Steel Plant
Steel Plate Mill Line No. 1
Jiangsu Province, 215625
Tel +86 0512 58568791 Fax: +86 0512 58558900 Email: mailto:ctotec@shagang.cn Web: http://www.sha-steel.com
Plates in Grades A and B Fine Grain Al+Ti in the Normalising Rolled condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to
60.0mm.
Plates in Grades D and E Fine Grain Al+Ti+Nb in the TM+Acc condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to 60.0mm.
Plates in the Normalizing Rolled condition and the TM+Acc condition are restricted to a maximum width of 4150mm.
Plates in the quenched and tempered supply condition >70mm thickness are accepted for approved applications only.
Plates in higher strength grades AH32 and AH36 as rolled 2800 wide x 11,000 long
Certificate No. MD00/3388/0008/1 Expiry date: 27/10/2016
JIANGSU SHAGANG GROUP CO., LTD
Jiangyin
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
A, B, D, E
AH27S, DH27S, EH27S, FH27S, FH32, FH36,
FH40
AH32, AH36, AH40, DH32, DH36, DH40, EH32,
EH36, EH40
360AR, 410AR, 460AR, 360FG, 410FG, 460FG,
490FG, 510FG
60
60
85
40
Hongfa Steel Plant
Steel Plate Mill Line No. 2
Tel +86 0512 5856 8791 Fax: +86 0512 5855 8900 Email: mailto:ctotec@shagang.cn Web: http://www.sha-steel.com
All the above grades may be produced with specified through thickness tensile properties when manufactured and tested in accordance with LR Rules for
'Plates with Specificed Through Thickness Properties'.
Plates in Grades A and B Fine Grain Al+Ti in the Normalising Rolled condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to
60.0mm.
Plates in the Normalizing Rolled are restricted to a maximum width of 4650mm condition and in the TM+Acc condition are restricted to a maximum width of
4150mm.
Plates in AH32 and AH 36 as rolled to 2800 x 11,000 and approved in the "as welded "condition
Certificate No. MD00/3913/0006/1 Expiry date: 27/10/2016
JIANGSU SHAGANG GROUP CO., LTD
Jiangyin
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Slabs
As below
carbon, carbon-manganese
320
83
150
Hongfa Steel Plant
Steelmaking Plant Number 2
Jiangsu Province 215625
Tel: +86 512 5856 8791 Fax: +86 512 5855 8900
Email: ctoec@shagang.cn Web http://www.sha-steel.com
Approval covers for con cast slabs to nominal sizes 2065mm wide x 9000mm long to the above maximum thickness.
Certifcate Number: MD00/3923/0003/1 Expiry date: 27/10/2016
JIANGSU SUNAN HEAVY MACHINERY
Jiangyin
Steelmaking
EAF/LRF/VD/Ingot
Alloy
Carbon, Carbon-manganese
Sections
Normal Strength
Higher Strength
A, B
AH27S, AH32, AH36
TECHNOLOGY CO LTD.
No.6 XingGang Road,
Economic & Technology Development Zone,
Changsu City,
Jiangsu Province,
Tel: +85 138 623 11673 Fax: 0512 51923689
email: zongjianh@163.com
Certificate No. MD00/4334/0001/1 Expiry Date: 10/06/2017
JIANGYIN BOFENG IRON & STEEL CO., LTD.
Jiangyin
40
40
Huaxicun Industrial Zone
Jiangyin City
Jiangsu Province
Tel: +86 13585066431 Fax: +86 510 8621 7672
Email: office2@bofengsteel.com Web: http://www.bofengsteel.cn
The approved sections are in the form of universal flats nominal widths <600mm to the maximum thickness shown above.
Certificate Number: MD00/4031/0002/1 Expiry: 05/06/2018
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
12
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
JIANGYIN HUAQIANG SPECIAL STEEL
Jiangyin
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy
Max Thickness/Diameter (mm)
32
CASTING & FORGING THERMOELECTRIC CO., LTD.
No. 18, Biangang Road,
Huaxi, Jiangyin City,
Jiangsu Province, 214421,
Tel: +86 510 862 10013 Fax: +86 510 862 03428 Mobile 0086 13812 582903 Email: mj2_hq@163.com
Ingots as semi finished products nominal 1240mm/1320mm diameter x 2770mm long to the above maximum weight are approved for further processing for
forgings.
Certificate Number: MD00/4013/0002/1 Expiry: 22/04/2018
JIANGYIN XINGCHENG SPECIAL STEEL WORKS
CO., LTD.
Jiangyin
Steelmaking
B.O.S./E.A.F./Con Cast
As Below
Semi-Finished
Slabs
Normal strength
250
Blooms
carbon, carbon-manganese, alloy
390
Semi-finished Products
carbon, carbon-manganese, alloy
900
Structural
carbon, carbon-manganese, alloy
180
Machinery
carbon, carbon-manganese, alloy
180
Chain Cable Stock
R4S
150
U1, U2, U3
180
R3, R3S, R4
230
Bars
297, Bin Jiang East Road
Jiangyin City
Jiangsu province 214429
Tel: +86 510 6193388-6165 Fax: +86 510 6195042
Email: mailto:jyxctg@public1.wx.js.cn
Web: http://www.jyxc.com
Certificate Number: MD00/2306/0017/1 Expiry: 25/09/2016
JIANGYIN XINGCHENG SPECIAL STEEL WORKS
CO., LTD.
Jiangyin
Steelmaking
B.O.S. / Con Cast
As below
Semi-Finished
Slabs
Normal strength, Higher Strength
Plates
Normal Strength
A, B, D, E
50
Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
50
40
360FG, 410FG, 460FG, 490FG, 510FG
50
Normal Strength
A, B, D, E
80
Higher Strength
DH40, EH40, FH27S, FH32, FH36, FH40
60
80
Boiler & Pressure Vessel
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
80
carbon, carbon-manganese
16
Boiler & Pressure Vessel
300
3500 Plate Mill
Jiangsu Province 214429
Tel: +86 510 6193388-6165 Fax: +86 510 6195042
Email: mailto:jyxctg@public1.wx.js.cn
Web: http://www.jyxc.com
Certificate Number: MD00/3857/0006/1 Expiry date: 25/09/2016
JIANGYIN XINGCHENG SPECIAL STEEL WORKS
CO., LTD.
Jiangyin
Plates
40
4300 Plate Mill
Tel: +86 510 6193388-6165 Fax: +86 510 6195042
Email: jyxctg@public1.wx.js.cn Web: http://www.jyxc.com
Plates in the Normalizing Rolled and Thermomechanical supply conditions are restricted to 3800mm maximum width.
Plates in the TM+Acc supply condition are restricted to thickness from 16mm to the maximum thickness shown above.
Z35 designation for through thickness properties may be added to all plates in the above supply conditions.
Certificate Number: MD00/3973/0003/1 Expiry date: 09/01/2018
JIGANG GROUP Co. LTD
Qingdao
Fabricated Sections
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
Structural Sections
13
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
Airport Road,
Licheng District,
Jinan,
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Steelmaking
Semi-Finished
EAF/LRF/VD/Ingot
Ingots (tonnes)
Carbon, Carbon-manganese, Alloy
carbon, carbon-manganese, alloy
10
10
Plates
Austenitic Stainless
304L, 316L
80
Steelmaking
B.O.S. / Con Cast
As below
Semi-Finished
Slabs
As below
300
Billets
carbon, carbon-manganese
300
Normal Strength
A, B, D, E
80
Higher Strength
DH40, EH40, FH32, FH36, FH40
50
AH32, AH36, DH32, DH36, EH32, EH36
80
360AR, 410AR
40
360FG, 410FG, 460FG, 490FG, 510FG
80
Shangdong
Tel: +86 531 88842106 Fax: +86 531 62325025
E-mail: zhucy_iglw@163.com
Website: www.jigang.com.cn
Certificate No. MD00/4595/0001/1
Expiry Date: 11/07/2019
KOCEL STEEL FOUNDRY CO., LTD.
Wuhan
199#, Tongxin Nan Road
Economic and technical development District
Yinchuan, Ningxia
Tel: 0951 2031028 Fax: 0951 2031218
email: david.li@kocel.com web: www.kocel.com
Certificate No. MD00/3515/0002/1 Expiry Date: 22/04/2017
KUNSHAN DAEKYUNG STAINLESS STEEL CO.,
Shanghai Port
LTD
No. 66 Longdeng Road
Kunshan Economy Technology Development Zone
Kunshan
Jiangsu Province
Tel:+86 512 57900998 Fax: +86 512 57700372
email: cuiyongxun020@naver.com
Certificate #: MD00/3479/0003/1 Expiry date: 07/06/2017
LAIWU STEEL GROUP LTD. YINSHAN SECTION
STEEL CORPORATION
Qingdao
Plates
Boiler & Pressure Vessel
Shuangquan Road,
Gangcheng district,
Laiwu,
Shandong
Tel: +86 634 7920316 Fax: +86 634 6820824
email: hao781109@126.com web: www.laigang.net
Certificate #: MD00/3855/0005/1 Expiry date: 07/11/2016
MAANSHAN IRON & STEEL COMPANY LIMITED
Nanjing
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
Normal strength, Higher Strength
A, B
AH32, AH36, DH32, DH36
360AR, 410AR
220
25
25
25
Steelmaking
Semi-Finished
EAF/LRF/VD/Ingot
Ingots (tonnes)
Carbon, Carbon-manganese, Alloy
carbon, carbon-manganese, alloy
25
25
No.8 Jiuhua West Road,
Maanshan City
Anhui Province PC:243000
Tel: +86 555 287 7110 Fax: +86 555 2886 904
Email: jjsskk2005@yahoo.com.cn.
Web http://www.magang.com.cn
Certificate #: MD00/0965/0008/1 Expiry date: 07/10/2018
MAANSHAN XINLONG SPECIAL STEEL CO., LTD.
Jiangyin
Taibai Industrial,
Dangtu town,
Maanshan City,
Tel: + 0555 667 5062 Fax: + 0555 667 5062
Certificate No: MD00/4402/0001/1 Expiry Date: 03/11/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
14
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
MINMETALS YINGKOU MEDIUM PLATE CO., LTD.
Dalian
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
As below
Normal strength, Higher Strength
A, B, D, E
AH27S, DH27S, EH27S
AH32, AH36, DH32, DH36, EH32, EH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
Boiler & Pressure Vessel
Max Thickness/Diameter (mm)
350
80
40
80
25
80
No 1 Fanrong Road, Yejin Street
Laobian District
Yingkou City
Liaoning Province
Tel: 086 (0)417 3256051 Fax: 086 (0)417 3256057
Email mailto:jszlb-wkyg@163.com
Web :www.wkyg.com
Plates with specified through thickness properties in listed grades of normal and higher strength steels.
Certificate #: MD00/2585/0007/1 Expiry date: 31/07/2017
NANJING IRON & STEEL CO., LTD.
Nanjing
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
E.A.F. / Con Cast
Slabs
Blooms
Billets
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
Bars
Chain Cable Stock
As below
As below
Normal strength, Higher Strength
Normal Strength, Higher Strength
Normal Strength, Higher Strength
A, B, D, E
AH27S, DH27S, EH27S, FH27S, FH32, FH36,
FH40, FH42, FH46, FH50, FH55
AH32, AH36, AH40, AH42, AH46, AH50, AH55,
AH62, AH69, DH32, DH36, DH40, DH42, DH46,
DH50, DH55, DH62, DH69, EH32, EH36, EH40,
EH42, EH46, EH50, EH55, EH62, EH69
360AR, 410AR, 360, 410
360FG, 410FG, 460FG, 490FG, 510FG
LTAH32, LTAH36, LTAH40, LTDH32, LTDH36,
LTDH40, LTEH32, LTEH36, LTEH40, LTFH32,
LTFH36, LTFH40, 5Ni, 9Ni
U1, U2, U3
220
320
150
100
60
100
25
100
60
180
Nanjing Works
XieJiaDian
Luhe District
Nanjing, Post Code: 210035
Tel: +86 25 5707 3657 Fax: +86 25 5707 4341
Email :wangwuyi@njsteel.com.cn
Web:http://www.njsteel.com.cn
Plates with specified through thickness properties may be accepted with the suffix Z35 applied to all approved grades
U2, U3 bars at 80mm diameter or less are produced by BOS or EAF steelmaking, bars over 80mm diameter are produced by EAF steelmaking.
Billets and blooms approved upto the above maximum thickness, 480mm width and nominal 12000mm length.
Slabs approved upto the above maximum thickness, 2510mm width and nominal 4000mm length.
Certificate Number: MD00/1065/0019/1 Expiry date: 13/10/2016
NANYANG HANYE SPECIAL STEEL CO., LTD.,
Wuhan
Steelmaking
Semi-Finished
Plates
B.O.S./Ingot/Con Cast
Ingots (tonnes)
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
360FG, 410FG, 460FG, 490FG, 510FG
Austenitic Stainless Steel
304L, 304LN, 316L
48
300
100
100
100
Huiche Town Industry Area,
Xixia County,
Nanyang City,
Henan Province
Tel No: +86 377 697 65211
Fax No: +86 377 697 65333
Email: zhaoyuan_521@sohu.com
Website: www.elongcheng.com
Certificate No: MD00/3969/0002/1
Expiry date 01/01/2018
OUTOKUMPU STAINLESS STEEL (CHINA) Co., Ltd.
Shanghai Port
Plates from coils
12
No. 288, Chenfeng Road
Yushan Town
Kunshan
Jiangsu Province
215300
Tel No: +86 512 50120382
Fax No: +86 512 50120392
Certificate No: MD00/4422/0001/1
Expiry date: 26/01/2018
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
15
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
PANGANG GROUP
Wuhan
Steelmaking
EAF/LRF/VD/Ingot
Semi-Finished
Ingots (tonnes)
Max Thickness/Diameter (mm)
Bars
Structural
Machinery
Alloy
Carbon, Carbon-manganese
alloy
carbon, carbon-manganese
alloy
carbon, carbon-manganese
alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
Steelmaking
B.O.S. / Ingot
As below
E.A.F. / Ingot
As below
Semi-Finished
Ingots (tonnes)
carbon, carbon-manganese, alloy
Plates
Normal Strength
E
32
A, B, D
35
Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36
32
Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG
32
360AR, 410AR
35
ESR Ingots
Bars
25
40
25
40
25
300
390
390
390
JIANGYOU CHANGCHENG SPECIAL STEEL CO., LTD.,
No.195, Jiangdong Road,
Jiangyou City,
Sichuan Province,
621701
Tel No: +86 816 365 087
Fax No: +86 816 3650463
Email zjbzgk@163.com
Web: http://www.cssc.com.cn
Certificate No: MD00/4201/0002/1 Expiry date: 12/07/2019
PENGZHOU SANXIN MACHINERY
MANUFACTURE Co. Ltd.
Wuhan
9
No. 49 Mengsan Road, mengyang Town
Pengzhou City, Sichuan Province
P.C 611934
Tel: +86 28 83773044 fAX: +86 28 83773071
Certificate #: MD00/3106/0004/1 Expiry date: 30/09/2016
QINHUANGDAO SHOUGANG PLATE MILL CO.,
LTD.
Dalian
No. 409 Jianshe Street
Qinhuangdao City
Hebei Province
Tel: +86 0335 3011421 3100 Fax: +86 0335 3014693
email: shouqinshichangbu@163.com
Certificate #: MD00/2097/0009/1 Expiry date: 04/07/2018
QINHUANGDAO SHOUQIN METAL MATERIALS
CO., LTD.
Dalian
Steelmaking
B.O.S. / Con Cast
carbon, carbon-manganese
Semi-Finished
Slabs
carbon, carbon-manganese
Plates
Normal Strength
D
50
A, B
Higher Strength
Boiler & Pressure Vessel
100
FH32, FH36, FH40
40
AH40, DH40, EH27S, EH32, EH36, EH40
60
AH36, DH27S, DH36
80
AH27S, AH32, DH32
100
360AR, 410AR
16
360, 410
32
510FG
80
360FG, 410FG, 460FG, 490FG
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
16
400
100
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
Duzhuang
Funing County
Qinhuangdao
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Hebei Province 066326
Tel +86 0335 6082696 Fax +86 010 6082690
Email: market@sq.shougang.com.cn web www.shouqin.com.cn
Certificate No: MD00/3136/0008/1
Expiry Date: 05/02/2017
All plate grades and thicknesses with through thickness properties, notations Z25 and Z35 may be added.
RIZHAO STEEL WIRE CO., LTD
Qingdao
Steelmaking
Semi-Finished
Hot Rolled Coil
Plates from coils
B.O.S. / Con Cast
Slabs
Normal Strength
Normal Strength
As below
carbon, carbon-manganese
A, B
A, B
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Slabs
Blooms
Billets
Normal Strength
Higher Strength
carbon, carbon-manganese
carbon, carbon-manganese, alloy
carbon, carbon-manganese
carbon, carbon-manganese, alloy
A, B, D, E
AH40, DH40, EH40
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
U3
230
25
25
No. 600, Yanhai Road, Rizhao
Shandong
Tel: +86 633 6188070 Fax: +86 633 6188155
email. jzwanggang@rizhaosteel.com web: www.rizhaosteel.com
Certificate #: MD00/3843/0002/1 Expiry date: 04/10/2016
SANXIN HEAVY INDUSTRY MACHINERY CO., LTD Jiangyin
40
Xia Xi North Road,
Jiaze,
Wujin, Changzhou,
Jiangsu, 213148
Tel No +86 519 83685577 Fax +86 519 83586556
Email xxxxxxxxxxxxxxx
Web www.sanxinzg.com
Certificate No MD00/4184/0001/1 Expiry Date 18/06/2016
SGIS SONGSHAN CO., LTD
Guangzhou
Plates
Boiler & Pressure Vessel
Bars
Chain Cable Stock
270
425
170
60
36
60
20
60
150
Qujiang District
Shaoguan City
Guangdong 512123
Tel: +86 (0)751 878 5354 Fax: +86 (0)751 878 6066
email ly73@21cn.com
Certificate #: MD00/2175/0011/1 Expiry date: 21/11/2018
CEV is limited to a maximum of 0.45% for as rolled and nomalised higher strength steels but does not apply to TM steels
SHANDONG IRON & STEEL CO., Ltd.
Qingdao
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Hot Rolled Coil
Normal Strength
Higher Strength
As below
carbon, carbon-manganese
E
A, B, D
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40, FH32,
FH36, FH40
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
A, B
AH27S, AH32, AH36
Steelmaking
B.O.S. / Con Cast
E.A.F. / Con Cast
Chain Cable Stock
As below
As below
U2, U3
Higher Strength
Boiler & Pressure Vessel
270
50
60
60
25
60
12
12
JINAN COMPANY
21, Gongye Bei Road
Jinan, 250101
Shandong Province
Tel +86 531 8886 5844 Fax +86 531 8898 2126
email: jigangleike@163.com web: www.jigang.com.cn
Certificate #: MD00/0799/0013/1 Expiry date: 15/10/2016
SHANDONG IRON & STEEL CO., Ltd.
Qingdao
Bars
130
LAIWU COMPANY
No.99 Fuqian Street
Gang Cheng District
Laiwu City
Tel: +86 634 7920316 Fax: +86 634 6820824
Email to: hao781109@126.com Web: http://www.laigang.net
Certificate No.: MD00/4389/0001/1
Expiry Date: 07/10/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
17
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
SHANDONG SHOUGUANG JUNENG SPECIAL
STEEL CO, LTD.
Qingdao
Steelmaking
B.O.S. / Con Cast
As below
Semi-Finished
Rolled Billets
Carbon, Carbon-Manganese
310
Billets
carbon, carbon-manganese
350
Structural
carbon, carbon-manganese
130
Machinery
carbon, carbon-manganese
130
Chain Cable Stock
U1, U2, U3
130
Semi-Finished
Bars
austenitic stainless
130
Steelmaking
EAF/LRF/VD/Ingot
Carbon, Carbon-manganese, Alloy
200
E.A.F./A.O.D./Con Cast
E.A.F/A.O.D/Ingot
Ingots (tonnes)
Slabs
Billets
Austenitic Stainless
Duplex Stainless
As below
As below
As below
As below
As below
304L, 316L
UNS S31803
8
200
230
20
40
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Normal Strength
Higher Strength
Boiler and Pressure Vessel
As below
Normal strength, Higher Strength
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
360FG, 410FG
A, B, D
AH27S, DH27S, AH32, DH32, AH36, DH36
410 FG, 360 FG
200
25
25
25
25
25
25
Bars
Max Thickness/Diameter (mm)
No. 9 Tegang Road
Shouguang, Shangdong Province
262711
Tel: +86 532 5186159 Fax No. +86 532 5186789
E-mail: zwsun2008@163.com
www.sgjntg.com
Certificate No:
MD00/3260/0005/1
Expiry date: 21/09/2018
SHANGHAI BAIHE WALSIN LIHWA
Shanghai Port
SPECIALTY STEEL PRODUCTS Co., Ltd.
No. 2402 Qingsong Road
Baihe Town, Qingpu District
Shanghai (201709)
Tel: +86 21 59746686 Fax: +86 21 59746686
Certificate No: MD00/4450/0001/1 Expiry Date: 21/03/2018
Approval for austenitic grades covers types 304L, 316L, 321, 347.
SHANGHAI HEAVY MACHINERY PLANT CO.,
LTD.
1800 Jiangchuan Road
Minhang District
Shanghai
200245
Shanghai Port
Tel: +86 21 54724065 ext 2027 Fax: +86 21 54721007 Email:chenzq@sechig.com Web http://www.shmp-sh.com
Certificate #: MD00/1345/0002/1 Expiry date: 24/07/2017
SHANXI TAIGANG STAINLESS STEEL CO., LTD.
Dalian
Steelmaking
Semi-Finished
Plates
Stainless Steel Hot Rolling Mill
Jiancaoping Street No. 2
Taiyuan
030003
Taiyuan
Tel No: +86 351 3012029
Fax No: +86 351 3017893 Mob: 13503502921
All plate grades with specified through-thickness properties
Email: Zhanghy02@tisco.com.cn
Web: http://tgbx.tisco.com.cn
Certificate No. MD00/3185/0008/1 Expiry date: 15/08/2017
SHANXI TAIGANG STAINLESS STEEL CO., LTD.
Dalian
Steelmaking
Semi-Finished
Hot Rolled Coil
Plates from coils
Hot Strip Mill
Jiancaoping Street No. 2
Tel: +86 351 3012029 Fax: +86 351 3017893 Mobile: +86 135 0350 2921
Email: Zhanghy02@tisco.com.cn Web: http: //www.tisco.com.cn
Slabs as semi finished products 2310mm nominal width and 12000mm nominal length to the above maximum thickness are approved for further processing for
rolled products.
Certificate #: MD00/3507/0003/1 Expiry date: 28/07/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
18
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
SHANXI TAIGANG STAINLESS STEEL CO., LTD.
Dalian
Plates
Normal Strength
Higher Strength
Austenitic Stainless
Duplex Stainless
A, B, D
AH32, AH36, DH32, DH36
304L, 316L, 304*, 316*
UNS S31803
Max Thickness/Diameter (mm)
40
40
60
40
Steelmaking
EAF/LRF/VD/Ingot
Carbon, Carbon-manganese, Alloy
12
Steelmaking
E.A.F. / Ingot
As below
Semi-Finished
Ingots (tonnes)
carbon, carbon-manganese, alloy
132
Steelmaking
Bars
B.O.S. / Con Cast
Structural
Machinery
Chain Cable Stock
carbon, carbon-manganese
carbon, carbon-manganese
carbon, carbon-manganese
U1, U2, U3
150
150
150
Steelmaking
B.O.S. / Con Cast
As below
Semi-Finished
Slabs
carbon, carbon-manganese
Hot Rolled Coil
Normal Strength
A, B, D
18
Higher Strength
AH32, AH36, DH32, DH36
18
Normal Strength
A, B, D
18
Higher Strength
AH32, DH32, AH36, DH36
18
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Normal Strength
Higher Strength
As below
carbon, carbon-manganese, alloy
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
360FG, 410FG, 460FG, 490FG, 510FG
A, B, D
AH27S, DH27S, AH32, DH32, AH36, DH36
Linfen Heavy Plate Mill
Qiaodong Street No.3
Linfen City
Shanxi Province
Tel: +86 351 3017667 Fax: +86 351 3017893
Email: yangfei@tisco.com.cn
Web: http:// www.tisco.com.cn
Certificate No MD00/3688/0005/1 Expiry date 07/07/2015
SHANXI TAIGANG STAINLESS STEEL CO., LTD.
Dalian
Section Steel Plant,
No.2 Jian Caoping Street,
Taiyuan City,
Shanxi Province,
Tel: +81 (0)351 3017667 Fax: +81 (0)351 3017893
Certificate No. MD00/4240/0001/1 Expiry Date: 15/10/2016.
SHI GANG JING CHENG EQUIPMENT
DEVELOPMENT
Dalian
AND MANUFACTURING CO., LTD.
No. 1 East Xinlian Street
Administrative Committee of Liaoning(Yingkou)
Castal Industrial Base
Tel: +86 0417 3257866 Fax: +86 0417 3257860
Email: caojun@cyedm.com.cn
Web: http://www.cyedm.com.cn
Certificate #: MD00/4234/0003/1 Expiry date: 09/10/2016
SHIJIAZHUANG I & S CO., LTD.
Dalian
No. 363 Heping E Road
Shijiazhuang City
Hebei Province
Tel: +86 (0)311 869 12562 Fax: +86 (0)311 869 13368
Email: sunjp_sggs@126.com
Certificate #: MD00/3315/0004/1 Expiry date: 05/02/2019
SHOUGANG JINGTANG UNITED IRON & STEEL
CO., LTD.
Qingdao
Plates from coils
250
Caofeidian Industrial Zone, Tangshan
Post Code: 063200
Tel: +86 315 8872636 Fax: +86 315 8872606
email: uha_w@126.com web: www.sgjsteel.com
Certificate #: MD00/3820/0002/1 Expiry date: 20/11/2016
SHOUGANG QIAN'AN IRON & STEEL COMPANY
Dalian
Steelmaking
Semi-Finished
Hot Rolled Coil
Plates from coils
230
18
18
18
18
18
No. 025, Zhao'an Road
West Industrial District
Qian'an City
Hebei, 064404
Tel: +86 315 7703138 Fax: +86 315 7703139
Email: mailto:zhengzhihui@sgqg.com
Web wwwsgqg.com
Certificate #: MD00/3488/0004/1 Expiry date: 08/07/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
19
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
SICHUAN LIUHE FORGING CO., LTD.
Wuhan
Steelmaking
EAF/LRF/VD/Ingot
Carbon, Carbon-manganese, Alloy
Max Thickness/Diameter (mm)
Sections
Normal Strength
Higher Strength
A, B, D, E
AH32, AH36, AH40, DH32, DH36, DH40, EH32,
EH36
Steelmaking
Bars
E.A.F. / Con Cast
Chain Cable Stock
As below
U1, U2, U3
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below, carbon, carbon-manganese
carbon, carbon-manganese
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
carbon, carbon-manganese
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
360FG, 410FG, 460FG, 490FG, 510FG
Sections
Normal Strength
Higher Strength
A, B
AH32, AH36
24
24
Sections
Normal Strength
Higher Strength
A, B
AH32, AH36
20
20
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Slabs
Billets
As below
Normal strength, Higher Strength
Normal Strength
8
Baolun Road(W), Henan Industrial Park
Jiangyou City
Sichuan Province
Tel No: +86 0816 3456788 Fax No: +86 0816 3521398
Email: bk.liwei'@gmail.com
Certificate No: MD00/4176/0002/1 Expiry date 08/06/2019
SUQIAN NANJING IRON & STEEL
Nanjing
20
20
JINXIN STEEL ROLLING Co., Ltd.
No.89 Jingshan Road,
Suyu District,
Suqian City, Jiangsu,
Tel; +86 527 844 53907 Fax: +86 527 844 80094
email: aqhw333@sina.com
Certificate: MD00/3741/0006/1 Expiry date: 16/12/2017
SUZHOU SUXIN SPECIAL STEEL CO., LTD.
Shanghai Port
120
Huashan, Tong An, Suzhou
Jiangsu
Post Code: 215151
Tel: +86 0512 8887 8163 Fax: +86 0512 88877273
email: wangtao@sugang.com.cn web: www.sugang.com.cn
Certificate #: MD00/3492/0003/1 Expiry date: 13/07/2017
TAI YUAN HEAVY INDUSTRY CO. LTD.
Wuhan
36
No.53, Yuhe Street,
Wanbailin District, Taiyuan City,
Shanxi Province, 030024,
Tel +86 351 636 6770 Fax: +86 351 636 6750
Email: litubin_9365@yahoo.com.cn
Web: www.tyhi.com.cn
Certificate #: MD00/3412/0003/1 Expiry date: 02/10/2016
TANGSHAN HEAVY PLATE CO., LTD.
Qingdao
250
38
38
38
Lingang Industrial Park
Leting County,
Tangshan City,
Hebei
Tel Nos: +86 315 4958145, +86 315 4958135 Fax No: +86 315 4959153
Email chuanbin04@126.com@163.com (enquiries), zhaowenge1966@126.com (orders)
Certificate #: MD00/3475/0004/1 Expiry date: 31/05/2017
TANGSHAN SHENGCAI STEEL CO., LTD.
Dalian
South of Xinghonglin Village
Angezhuang Town,
Luannan County, Tangshan City,
Hebei Province
Tel No: +86 315 245 0855 Fax No: +86 315 445 1116
email scgtbgs@126.com web: www.731147959@qq.com
Certificate No: MD00/4131/0003/1
Expiry Date 18/03/2019
TANGSHAN XINXIN SPECIAL STEEL CO. LTD
Qingdao
No. 95 Middle Street
Bencheng Town, Luannan County
Tangshan City
Tel: +86 0315 412 5016; Fax: +86 0315 415 2881
email: mengfen123@163.com web: www.xxtg.cn
Certificate #: MD00/3468/0006/1 Expiry date: 17/05/2017
TANGSHAN YANSHAN IRON & STEEL CO., LTD.
Dalian
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
20
250
150
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
The West Side of Qianan Railway Station
Qianan City
Hebei Province (064403)
Tel: +86 315 7769 566 Fax: +86 315 7769 566
E-mail: hesong44@126.com
Billets nominal maximum width 150mm x 12,000mm nominal maximum length to the above maximum thickness supplied in the As Cast condition; slabs
nominal maximum width 1,800mm x 12,000mm nominal maximum length to the above maximum thickness supplied in the As Cast condition; are approved for
further processing for rolled products in the detailed strength levels.
Certificate Number: MD00/3648/0005/1 Expiry: 08/06/2018
TIANJIN IRON AND STEEL GROUP CO. LTD.
Qingdao
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
As below
carbon, carbon-manganese, alloy
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
250
38
50
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Blooms
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
400
Steelmaking
E.A.F. / Ingot
carbon, carbon-manganese
90
Sections
Normal Strength
Higher Strength
A, B
AH32, AH36
15
15
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
70
70
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Hot Rolled Coil
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Normal Strength
Higher Strength
Boiler and Pressure Vessel
As below
As below
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
360, 410
A, B, D
AH27S, DH27S, AH32, DH32, AH36, DH36
360, 410
398 Jintang Road
Dongli District
Tianjin
Tel:+86 22 24706052 Fax: +86 22 24706052
Email: TGRZ166@yeah.net
web: www.tgsteel.com
Certificate #: MD00/3485/0004/1 Expiry date: 01/07/2017
TIANJIN PIPE (GROUP) CORPORATION
Dalian
No 396, Jintang Road
300301
Tel No: +86 22 2480 2296
Fax no: +86 22480 1291
Email zhangyh@tpco.cn
Web: www.tpco.com
Certificate No MD00/3361/0004/1 Expiry Date 28/07/2019
TIANJIN TIANZHONG GIANT HEAVY INDUSTRY
CO., LTD.
No. 609, Jinyu Road
Xiditou Town
Beichen District
Qingdao
Tianjin
Tel:+86 (0)22 86885730 Fax: +86(0)22 8688 5673
emsil: jtzgdz@163.com web: www.jiangtian.cn
Certificate No: MD00/4094/0003/1 Expiry date: 24/11/2018
TIANJIN YONGHENG ENTERPRISE CO., LTD.
Dalian
No. 5, Gangtuan West Road
Daqiu Town, Jinghai County
Tianjin, 301606
Tel:+86 (0)2228899180 Fax: +86(0)2228899185
Email:wy8770@163.com Web:http://www.tjyhsy.com
Certificate #: MD00/3953/0002/1 Expiry date: 24/09/2017
TONGYU HEAVY INDUSTRY Co., Ltd
Qingdao
High & New Technology Industry Development Zone,
Yucheng City,
Dezhou City,
Shandong Province,
Tel: +86 534 7520690 Fax: +86534 7521470
Certificate No. MD00/3998/0002/1 Expiry date: 28/02/2018
WISCO
Wuhan
Plates from coils
250
50
50
40
50
25
25
12
25
25
12
Wuhan Iron and Steel Co., Ltd.
Changqian
Qingshan
Wuhan
Tel: +86 27 8689 8498 Fax: +86 27 8689 2413
email: 782650488@qq.com web: www.wisco.com.cn
Certificate #: MD00/1683/0010/1 Expiry date: 20/11/2016
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
21
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
WUHAN HEAVY INDUSTRY
Wuhan
Semi-Finished
Ingots (tonnes)
carbon, carbon-manganese, alloy
Max Thickness/Diameter (mm)
100
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
As below, Normal strength, Higher Strength
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG
300
50
50
50
Steelmaking
E.A.F. / Ingot
As below
Semi-Finished
Ingots (tonnes)
carbon, carbon-manganese, alloy
Steelmaking
Plates
E.A.F./Ingot/Con Cast
Normal Strength
Higher Strength
As below
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
CASTING AND FORGING CO., LTD.
1 Wudong Street
Quingshan District
Hubei
Tel No:+86 027 6886 1813 Fax No: +86 027 6886 1810 Mob :+86 13720291417
Email wh471zg@163.com
Web www.whzg.com.cn
Certificate No: MD00/1681/0002/1 Expiry date: 03/04/2017
WUHAN IRON & STEEL GROUP
Wuhan
ECHENG IRON & STEEL CO., LTD.
Wuchang Dadao No. 105
Ezhou City
Hubei Province, 436002
Tel: +86 711 3233225 Fax: +86 711 3233225
Email: 13986400824@qq.com
www.ecsteel.com.cn
Certificate #: MD00/3931/0003/1 Expiry date: 04/07/2017
WUHAN ZHONGYE MACHINERY WHOLE SET
EQUIPMENT
Wuhan
18
Gourp Co., Ltd.
DAYE BRANCH
Lingcheng Road No. 2
Lingxiang Town, Daye City
Hubei Province
Tel: +86 0714 370 2019 Fax: +86 0714 370 2196
Email : ZG1819ZG@163.com
Certificate #: MD00/4242/0001/1 Expiry date: 28/10/2016
WUYANG IRON & STEEL COMPANY LTD.
Wuhan
Boiler & Pressure Vessel
150
100
40
100
Wugang City
Henan Province
P.N: 462500
Tel: +86 375 811 1230 Fax: +86 375 811 4006
E-mail: wgzhangweijun@163.com
Plates with specified through thickness properties in listed grades of normal and higher strength steels.
Certificate #: MD00/2044/0009/1 Expiry date: 25/03/2017
WUYANG IRON & STEEL COMPANY LTD.
Wuhan
Plates
Normal Strength
Higher Strength
A, B, D, E
FH32, FH36, FH40
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40
360FG, 410FG, 460FG, 490FG, 510FG
100
EAF/LRF/VD/Ingot
Ingots (tonnes)
ESR Ingots
Semi-finished Products
Carbon, Carbon-manganese, Alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
12
18
250
B.O.S. / Con Cast
E.A.F. / Con Cast
Slabs
Normal Strength
Higher Strength
See notes
See notes
carbon, carbon-manganese
A, B, D, E
FH27S, FH32, FH36, FH40
AH27S, AH40, DH27S, DH40, EH27S, EH40
250
80
50
60
Boiler & Pressure Vessel
100
50
100
Wuyang New Wide and Heavy Steel Plate Co Ltd
Wugang City,
Henan Province,
PN 462500
Tel No. +86 375 8111230 Fax No. +86 375 8114006 Email to: wgzhangweijun@163.com
Plates with specified through thickness properties in listed grades of normal and higher strength steels
Certificate No. MD00/3714/0003/1
Expiry Date 25/03/2017
XINING SPECIAL STEEL CO., LTD.
Wuhan
Steelmaking
Semi-Finished
Bars
No. 52 Chaidamu West Road
Xining
Qinghai Province, 455004
Tel: 0086 0971 529 9294 Fax: 0086 0971 529 9407
Email: cyuian@sina.com
Web: www.xntg.com
Certificate #: MD00/3798/0003/1 Expiry date: 10/03/2019
XINYU IRON & STEEL CO. LTD.
Wuhan
Steelmaking
Semi-Finished
Plates
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
22
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Wuhan
Plates
Higher Strength
Boiler & Pressure Vessel
Sections
Normal Strength
Higher Strength
AH32, AH36, DH32, DH36, EH32, EH36
360AR, 410AR
360, 410
360FG, 410FG, 460FG, 490FG, 510FG
A, B
AH27S, AH32, AH36
80
20
60
80
14
14
Alloy
Carbon, Carbon-manganese
alloy
carbon, carbon-manganese
24
34
24
34
China, People's Republic of
XINYU IRON & STEEL CO. LTD.
1 Yejin Road
Xinyu City
Jiangxi Province 338001
Tel: 0791 6293506
Email: XR@xinsteel.com.cn
Web: www.xinsteel.com.cn
All grades with specified through thickness properties, designation to Z35 may be added
Certificate #: MD00/3093/0009/1 Expiry date: 10/06/2019
XINYU XINLIANG SPECIAL STEEL CO., LTD.
Wuhan
Steelmaking
EAF/LRF/VD/Ingot
Semi-Finished
Ingots (tonnes)
Steelmaking
Semi-Finished
Plates
B.O.S./Ingot/Con Cast
Slabs
Normal Strength
Higher Strength
Liangshan Town
Xinyu, 338013
Jiangxi
Tel +86 (0)731 5865 2130 Fax +86 (0) 731 58653050
email:
Certificate #: MD00/4596/0001/1 Expiry date: 12/07/2019
Approved for Z25 & Z35 grades.
XISC - HUNAN VALIN XIANGTAN
Wuhan
Boiler & Pressure Vessel
Ferritic Low Temperature
As below
carbon, carbon-manganese, alloy
A, B, D, E
FH40
FH27S, FH32, FH36
AH40, DH40, EH40, EH47
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG
LTAH32, LTAH36, LTAH40, LTDH32, LTDH36,
LTDH40, LTEH32, LTEH36, LTEH40, LTFH32,
LTFH36, LTFH40
300
150
40
60
80
150
100
40
IRON & STEEL CO., LTD.
Yuetang District,
Xiangtan City,
Hunan Province,
Tel +86 (0)731 5865 2130 Fax +86 (0) 731 58653050
email mailto:hnxgjiazg@sohu.com web http://www.hnxg.com.cn
Certificate #: MD00/3258/0009/1 Expiry date: 08/08/2015
Approved for Z25 & Z35 grades.
YANTAI WALSIN STAINLESS STEEL CO., LTD.
Qingdao
Steelmaking
Semi-Finished
E.A.F./V.O.D./Con Cast
Blooms/Billets
As below
austenitic stainless steel, duplex stainless steel,
alloy steel
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
Bars
austenitic stainless, duplex stainless
austenitic stainless, duplex stainless
austenitic stainless, duplex stainless
11
500
Steelmaking
Bars
E.A.F. / Con Cast
Chain Cable Stock
As below
U2, U3
130
260
No. 2 Wuzhishan Road,
Economic Technical Development Zone
Yantai City, shandong Province
Tel: +86 535 2166688 Fax: +86 535 2165008 Email:Lisa_zhao@walsin.com
Certificate #: MD00/3992/0002/1 Expiry date: 20/02/2018
YONGXING SPECIAL STAINLESS STEEL CO LTD
Shanghai Port
Yangjiabu,
Huzhou City,
Zhejiang Province
Tel No. +86 572 2350629 Fax No: +86 572 2351517
Email: wang _jianyong@163.com
Web : www.yongxingbxg.cn
Certificate No. MD00/3791/0003/1 Expiry date 05/06/2019
ZENITH STEEL GROUP CO., LTD.
Jiangyin
No. 1 Zhongwu Avenue
Changzhou City
Jiangsu Province
Tel No. +86 519 88771301 Fax No: +86 519 88771301
Email: ludengyao@126.com
Certificate No. MD00/4273/0002/1 Expiry date 22/12/2016
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
23
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
ZHEJIANG TSINGSHAN IRON & STEEL CO.LTD.
Zhoushan
Steelmaking
Semi-Finished
IF/AOD/Ingot/ConCast
Ingots (tonnes)
Blooms/Billets
Billets
austenitic
austenitic
austenitic
austenitic
Max Thickness/Diameter (mm)
Steelmaking
A.O.D./Con Cast
As below
Plates from coils
Austenitic Stainless Steel
304L, 316L, 321
16
Duplex Stainless
UNS S31803
10
Austenitic Stainless
304L, 316L, 321
16
Duplex Stainless
UNS S31803
10
Steelmaking
B.O.S. / Con Cast
As below
Semi-Finished
Slabs
carbon, carbon-manganese
Plates
Normal Strength
A, B, D
38
Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36
38
Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG
38
Ingots (tonnes)
Blooms/Billets
EAF/LRF/VD/Ingot
IF/AOD/Ingot
carbon, carbon-manganese, alloy, stainless steel
As above
carbon, carbon-manganese, alloy
austenitic stainless
stainless steel
stainless
stainless steel
stainless
3
240
150
Xiaoshi Industry Zone
Wenxi Town,
Qingtian,
Zhejiang Province
Tel No. 0086 578 6071301
Fax No. 0086 578 6062336
Email 1030009089@qq.com
Web : www. zjqingshan.cn
Cert no. MD00/3673/0003/1 Expiry date: 24/08/2018
ZHENSHI GROUP EASTERN SPECIAL STEEL CO.,
LTD.
Shanghai Port
Coil
Economic Development park (North)
Xinfeng Town
Nanhu District, Jiaxing
Zhenjiang Province 314005
Tel: +86 573 8398 8183 Fax: +86 573 8391 6907 Email to: lijie@zsess.com
Certificate #: MD00/4426/0001/1 Expiry date: 29/01/2018
ZHONGPU (HANDAN) IRON AND STEEL CO.,
LTD.
Dalian
320
No.1 & No.2 Steel Making Plant
Yangyi Town,
Wuan City,
Hebei Province, 056305
Tel: +86 (0)310-5178955 Fax: +86 (0)310-5178928
email: zprzb2008@163.com web: www.hbpygt.com
Certificate #: MD00/4034/0002/1 Expiry date: 26/04/2018
ZHONGXING ENERGY EQUIPMENT CO., LTD
Nantong
Semi-Finished
Steel-making
6
350
6
6
No. 899, Zhonghua East Road
Sanchang
Haimen City
Jiangsu Province
Tel: +86 513 82608033 Contact: Mr Liu Zi Ping
Email to: nttgsyh@163.com
Web http://www.zxnyzb.com
Certificate #: MD00/4505/0002/1 Expiry date: 29/07/2018
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
24
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Zagreb
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Billets
As below
carbon, carbon-manganese
Steelmaking
B.O.S. / Con Cast
carbon, carbon-manganese, alloy
Semi-Finished
Slabs
carbon, carbon-manganese
150
alloy
180
Billets
carbon, carbon-manganese, alloy
200
Sections
Normal Strength
A, B, D
14
Bars
Normal Strength
A, B, D
60
Croatia
ABS SISAK d.o.o.
410
BRAE KAVURIA 12,
44010 Sisak,
Tel: +385 44 565467
email: t.marjanovic@absacciai.it
Cert No. MD00/4210/0001/1 Expiry date: 25/07/2016
Czech Republic
ARCELORMITTAL ENGINEERING PRODUCTS
OSTRAVA s.r.o
Prague
Vratimovská 689
707 02 Ostrava-Kuncice
Approval for semi finished products covers con cast slabs to 150 x 1270mm, con cast billets to 180 x 180mm and con cast rounds to 400mm diameter.
Tel: +420 59 568 4130
email: shahab.husain@arcelormittal.com
web: www.arcelormittal.com/ostrava
Certificate #: MD00/1123/0009/1 Expiry date: 11/12/2016
ARCELORMITTAL TUBULAR PRODUCTS KARVINA Prague
A.S.
Rude armady 471
733 23 Karvina
Fabricated Sections
Structural Sections
carbon, carbon-manganese
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
As below
Normal strength, Higher Strength
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG
5
Tel: +420 596 391 330 M: +420 724 555 571 Fax: +420 598 391 337
Email to: daniel.stolarz@arcelormittal.com Web http://www.jakl.cz
Longitudinal high frequency induction (HFI) welded tubes, pipes and hollows
Certificate #: MD00/4299/0001/1 Expiry date: 25/03/2017
ING. MATAS - SLEVARNA STRASICE, SPOL. S R.O.
Prague
Steelmaking
Semi-Finished
Plates
Boiler & Pressure Vessel
250
100
100
100
709 00 Ostrava - Hulvaky
Stramberska c.p. 2871/47
PSC 709 00
Tel: +420 59 595 5842 Fax: +420 602 485 466 Email: mailto:miroslav.snajdr@cz.evraz.com
Web: http://www.evrazvitkovicesteel.com
Approved for plates with specified through thickness properties (Z35) in all grades up to 50 mm thickness.
Semi-finished products in carbon and carbon-manganese steels with fine grain: slabs to 1580mm wide to 8000mm long for further processing for rolled products
Materials Quality Scheme Approved - MQS 039
Certificate #: MD00/1638/0014/1 Expiry date: 06/08/2016
PILSEN STEEL s.r.o.
Prague
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy
200
Tylova 1/57
316 00 Plzen
Tel: +420 378 134 225 Fax: +420 378 132 058
Email: karel.rau@pilsensteel.cz
Web: www.pilsensteel.cz
Certificate # MD00/1383/0006/1 Expiry date: 23/03/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
25
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
TRINECKE ZELEZARNY, a.s.
Prague
Steelmaking
B.O.S./Ingot/Con Cast
E.A.F./Ingot/Con Cast
Slabs
Bars
Normal Strength
Machinery
Chain Cable Stock
As below
As below
carbon, carbon-manganese
carbon, carbon-manganese, alloy
A
carbon, carbon-manganese, alloy
U1, U2
140
525
50
90
72
Structural
Machinery
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
300
300
Semi-Finished
Sections
Bars
Max Thickness/Diameter (mm)
Prumyslova 1000
Stare Mesto
739 61 Trinec
Tel: +420 558 534 016 Fax: +420 558 536 060
Email: mailto:radim.raska@trz.cz
Web hppt://www.trz.cz
Certificate #: MD00/1562/0008/1 Inspection Due: 12/07/2019
TRINECKE ZELEZARNY, a.s.
Prague
Bars
Prumyslova 1000, Stare Mesto
739 61 Trinec
vyrobni zavod:
VZ - Sochorova valcovna
272 01 Kladno Drin
Tel No +420 558 536 065 Fax No. +420 558 534 926
Email vit.prochazka@trz.cz
Web www.trz.cz
Machinery grade bars with the maximum diameter of 300 mm produced from con-cast blooms may be accepted with a minimum rolling reduction of 3:1.
Certificate #: MD00/2955/0007/1 Expiry date: 20/02/2018
TRINECKE ZELEZARNY, a.s.
Prague
Sections
Normal Strength
Higher Strength
B, D
A
DH32, DH36
AH27S, AH32, AH36
40
50
40
50
VH - Univerzalni trat Bohumin,
Bezrucova 300,
735 93 Bohumin
Tel: +42 (0) 558 534 016 or +42(0) 602 780 683
email: martin.snapka@moravia-steel.cz web: www.trz.cz
The approved sections are in the form of universal flats nominal widths 150 to 550mm to the maximum thicknesses shown above.
Parent Company: TRINECKE ZELEZARNY a.s., Prumyslova 1000, 739 70 Trinec-Stare Metso.
Certificate ID No : MD00/2020.
Certificate No. MD00/3056/0006/1 Expiry date: 11/02/2019
VITKOVICE HEAVY MACHINERY a.s.
Prague
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
As below
carbon, carbon-manganese
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36
80
Ruska 2887/101
70602 Ostrava-Vitkovice
Tel: +420 595 95 6491
Mob: +420 724 135544
email: petr.vasicek@vitkovice.cz web: www.vitkovice.cz
Certificate #: MD00/2020/0006/1 Expiry date: 30/03/2017
VITKOVICE STEEL, a.s.
Prague
Boiler & Pressure Vessel
Normal Strength
Higher Strength
Sections
Bars
Normal Strength
Higher Strength
250
100
100
100
16
16
50
50
709 00 Ostrava - Hulvaky
Stramberska c.p. 2871/47
PSC 709 00
Tel: +420 59 595 5842 Fax: +420 59 595 7340 Email: mailto:miroslav.snajdr@VitkoviceSteel.com
Web: http://www.vitkovicesteel.com
The maximum plate thickness manufactured by con-cast route is 70mm.
Approved for the OXYVIT Steelmaking Process.
Approved for plates with specified through thickness properties (Z35) in all grades up to 50 mm thickness.
Semi-finished products in carbon and carbon-Manganese steels with fine grain: slabs to 1580mm wide to 8000mm long for further processing for rolled products.
Certificate #: MD00/1638/0001/1 Expiry date: 06/08/2016
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
26
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Z - GROUP STEEL HOLDING A.S.
Prague
Steelmaking
E.A.F. / Ingot
carbon, carbon-manganese, alloy
Max Thickness/Diameter (mm)
4
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
12
Plates
Normal Strength
E
A, B, D
EH32, EH36, EH36S
AH27S, AH32, AH36, DH27S, DH32, DH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
60
100
80
100
40
100
100
20
Works Hradek
Rokycanska 204,
CZ-338 42 Hradek u Rokycan,
Tel: +420 474 644096 Fax: +420 474 642 288
Email: stehlik.libor@steel-holding.cz
Web: www.steel-holding.cz
Certificate #: MD00/4063/0003/1 Expiry date: 04/08/2018
ZDAS, a.s.
Prague
Metallurgical Plant
Strojirenska 675/6
59101 Zdar nad Sazavou
Tel: +420 566 643 054 Fax: +420 566 642 859
Email: stanislav.suhaj@zdas.cz
Web:http://www.zdas.cz
Certificate #: MD00/1697/0005/1 Expiry date: 25/08/2017
Denmark
NLMK DANSTEEL A/S
Copenhagen
Higher Strength
Boiler & Pressure Vessel
Havnevej 33
DK-3300 Frederiksværk
Tel: +45 477 82647 Fax: +45 477 70302 Email: mailto:E.Sarkits@dansteel.dk Web:http://www.dansteel.dk
All grades and thicknesses accepted with specified through thickness properties, Z25 and Z35 designations.
Certificate Number: MD00/0403/0008/1 Expiry: 09/01/2018
Egypt, Arab Republic of
ABU ZAABAL ENGINEERING INDUSTRIES
Cairo
Plates
Normal Strength
Higher Strength
A, B, D
AH27S
Steelmaking
Plates
Hot Rolled Coil
B.O.S. / Con Cast
Normal Strength
Normal Strength
Boiler & Pressure Vessel
Normal Strength
As below
A
A
360FG, 410FG
A
Hot and Cold Rolling mill (AZE)
Abu Zaabal
Inchas
Tel: +20 24469 1224 Fax: +20 24469 2608
Email: aze100@soficom.com.eg
Web www.azr.com
Certificate # MD00/3421/0004/1 Expiry date: 27/01/2017
EGYPTIAN IRON & STEEL CO.
Port Said
Sections
50
50
25
50
El Tebbin
Helwan
Cairo
Tel: +202 5940593 Fax +202 5011608
Email: mailto:eisc@idsc.net.eg
Web www.iron.steel.com.eg
Telex 20176 Tebbin
Certificate #: MD00/0438/0008/1 Expiry date: 21/02/2016
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
27
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
E.A.F. / Con Cast
As below
Slabs
austenitic stainless
Plates
Austenitic Stainless
304L, 316L, 321
12
Hot Rolled Coil
Austenitic Stainless
304L, 316L, 321
12
Coil
Austenitic Stainless
304L, 316L, 321
6
E.A.F. / Con Cast
As below
Blooms
carbon, carbon-manganese, alloy
370
Rolled Bars
Carbon, Carbon manganese, Alloy
180
Higher Strength
180
Structural
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
carbon, carbon-manganese, alloy
Machinery
alloy
180
carbon, carbon-manganese
200
Finland
OUTOKUMPU STAINLESS OY
Helsinki/Helsin Steelmaking
gfors
Semi-Finished
187
Terastie 1,
95490
Tornio
Tel No: +358 40 7675371 Fax no:+358 16 452 350
Email:susanna.siukonen@outokumpu.com
Web: http://www.outokumpu.com
Certificate #: MD00/1165/0007/1 Expiry date: 01/03/2017
OVAKO IMATRA OY AB
Helsinki/Helsin Steelmaking
gfors
Semi-Finished
Bars
180
Terästehtaantie 1
FI-55100 IMATRA
Tel: +358 5 680 21 Fax: +358 5 680 2211
Email: ville.ruotsalainen@ovako.com Web:http://www.ovako.com
Semi-finished products in carbon, carbon-manganese and alloy steel with fine grain (element combinations as stated), blooms to 370 mm section, to 6000mm long
for further processing to rolled products
MQS Approved - Approval No. MQS 020
Certificate #: MD00/0751/0010/1 Expiry date: 05/01/2018
SSAB EUROPE OY
Helsinki/Helsin Steelmaking
gfors
Plates
B.O.S. / Con Cast
As below
Normal Strength
A, B, D, E
Higher Strength
FH27S, FH32, FH36
40
AH40, DH40, DH42, EH40, EH42
80
Boiler & Pressure Vessel
Ferritic Low Temperature
Hot Rolled Coil
Normal Strength
Higher Strength
150
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
150
360, 410, 460, 490, 360FG, 410FG, 460FG, 490FG,
510FG
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
A, B, D, E
100
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
40
40
15
15
Raahe Steel Works
Rautaruukintie 155, PO Box 93
92101 Raahe
Tel +358 20 5911 Mob +358 40 54 90257 Fax +358 20 5923527 Email:mailto:lassi.myllykoski@ruukki.com Web: http://www.ruukki.com
Specified through thickness properties for up to 100 mm thickness.
MQS Approved - Approval No. MQS 007
Certificate #: MD00/1233/0010/1 Expiry date: 10/12/2016
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
28
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Lyon
Steelmaking
Semi-Finished
EAF/LRF/VD/Ingot
Ingots (tonnes)
Carbon, Carbon-manganese, Alloy
carbon, carbon-manganese, alloy
France
AKERS FRANCE
70
USINE DE THIONVILLE
Chemin du Leidt
B.P. 10200
57104 Thionville Cedex
Tel: +33 6 79 27 94 41 e mail: mailto:christophe.evrard@akersrolls.com web: http://www.akersrolls.com
Certificate #: MD00/3386/0003/1 Expiry date: 26/05/2017
APERAM
Gueugnon Plant BP 1
Lyon
Plates
Austenitic Stainless
304L, 316L, 321, 304*
6
E.A.F. / Ingot
Fe-Ni alloys
Fe-Ni alloys
As below
Fe-36Ni*
Fe-36Ni*
8
1
4 place des Forges
71130 Gueugnon
Tel: +33 3 85 85 78 56 Fax: +33 3 85 85 14 12 Mob: +33 609320872
Email: mailto:gerard.ramoissenet@aperam.com
Web: http://www.aperam.com
Certificate #: MD00/1582/0006/1 Expiry Date: 10/03/2017
APERAM ALLOYS IMPHY
Lyon
Steelmaking
Plates
Hot Rolled Coil
Avenue Jean Jaurès
58160 IMPHY
Tel: +33 3 86 21 34 96 Email:mailto:marie-paul.solignac@aperam.com Web:http://www.aperam.com
*Cold and hot rolled strip up to 8mm in INVAR/M93 grade (Fe-Ni36) accepted for approved applications; material greater than 1.5mm supplied in the As
Rolled condition; materials 1.5mm or less are supplied in the solution annealed condition.
Certificate Number: MD00/1870/0007/1 Expiry: 1/06/2018
ARCELORMITTAL
Marseille
Steelmaking
Semi-Finished
Hot Rolled Coil
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
Normal strength, Higher Strength
A, B, D
AH32, AH36, DH32, DH36, EH36
460FG, 490FG, 510FG
360AR, 410AR
229
16
13
13
16
Steelmaking
Semi-Finished
Bars
E.A.F./Ingot/Con Cast
Blooms/Billets
Structural
Machinery
Chain Cable Stock
As below
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
U3
U1, U2
400
310
310
105
130
Bars
E.A.F. / Ingot
Blooms
Billets
Structural
As below
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
400
205
325
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless
Méditerranée Fos-sur-Mer
13776 Fos-Sur-Mer
CEDEX
Tel: +33 (0) 442 47 30 68
Fax +33 (0) 4 4247 32 31
Email: mailto: christophe.issartel@arcelormittal.com
Web: www.arcelormediterranee.com
Certificate #: MD00/3803/003/1 Expiry date: 24/11/2018
ASCO INDUSTRIES S.A.S
Dunkerque
Usine de Dunes
BP 41
59941 Dunkerque
Cedex 2
Machinery grades up to 180 mm by continuous casting, 310 mm by ingot
Tel +33 32829 6052 Email to: corinne.lebihan@ascometal.com
Certificate #: MD00/0117/0008/1 Expiry date: 11/09/2018
ASCO INDUSTRIES S.A.S
Marseille
Steelmaking
Semi-Finished
Usine de Fos-sur-Mer
BP 30
13771 Fos-sur-Mer
Tel: +33 (0) 442 479251 Fax: +33 (0) 442 479276
Email : etienn.archaud@ascometal.com
Website: ascometal.com
Certificate Number: MD00/0118/0007/1 Expiry: 02/09/2018
AUBERT & DUVAL
Lyon
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
29
42
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
Firminy Plant
BP 141
42704 FIRMINY CEDEX
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Tel: +33 4 77 40 37 41 Email mailto: christrophe.mercier@eramet-aubertduval.com
Web: http://www.aubertduval.com
Ingots as semi-finished products to the above maximum weight; nominal; 1550/1730mm diameter x 2200mm; are approved for further processing for forgings.
Certificate Number: MD00/1770/0003/1 Expiry: 25/09/2018
AUBERT & DUVAL
Lyon
Steelmaking
Semi-Finished
E.A.F. / Ingot
Blooms/Billets
Bars
Structural
Machinery
As above
alloy, austenitic stainless steel, carbon, carbon
manganese
carbon, carbon-manganese, alloy, austenitic
stainless
carbon, carbon-manganese, alloy, austenitic
stainless
450
50
200
Aciéries des Ancizes
BP 1
63770 Les Ancizes
Tel: +33 4 73 67 31 27
email: marc.graglia@eramet-aubertduval.com www.aubertduval.com
Certificate No: MD00/4537/0001/1 Expiry Date: 21/12/2018
CELSA FRANCE
Bilbao
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Billets
As below
Normal Strength, Higher Strength
160
Rond-Point Claudius Magnin
64340 Boucau
Tel: +33 05 59 64 41 00 Fax: +33 05 59 64 41 21
email: dgonzalezt@gcelsa.com web: hwww.celsafrance.com
Certificate Number: MD00/3539/0003/1 Expiry date: 10/11/2017
Billets as semi-finished products, nominal 160mm width and nominal 13300mm length to the above maximum thickness are approved for further processing for
rolled products.
DILLINGER FRANCE
Dunkerque
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
E
A, B, D
AH40, DH40, EH40, FH40
FH27S, FH32, FH36
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
460FG, 490FG, 510FG
360FG, 410FG
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
80
100
42
50
75
50
100
50
Port 3032
3032 Rue du Comte Jean - CS 56317
F-59379 Dunkerque Cedex 1
Tel: +33 (0)3 28 29 39 22 Fax: +33 (0)3 28 29 69 12
Email: sylvie.brachet@fr.dillinger.biz
Web: http://www.dillinger-france.com
Specified through thickness properties for all normal and higher strength grade plates notation - Z35 may be added.
Certificate #: MD00/1818/0010/1 Expiry date: 07/06/2019
INDUSTEEL FRANCE
Lyon
Steelmaking
Plates
E.A.F. / Ingot
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
carbon, carbon-manganese
A
FH32, FH36
AH32, AH36, DH32, DH36, EH32, EH36
360AR, 410AR
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,
LTEH36, LTFH32, LTFH36, 1.5Ni, 3.5Ni, 5Ni,
9Ni
400
50
400
40
100
50
ARCELOR MITTAL
Site de Chateauneuf
BP 368 - Chateauneuf
42803 RIVE DE GIER
Tel: +33 4 77 75 21 12 Fax: +33 4 77 75 20 03
Email: jean-philippe.baron@arcelormittal.com
Including plates with specified through thickness properties.
Certificate #: MD00/0351/0007/1 Expiry date: 19/04/2017
INDUSTEEL FRANCE, site du Creusot
Lyon
Steelmaking
Semi-Finished
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
E.A.F. / Ingot
Ingots (tonnes)
30
As below
carbon, carbon-manganese, alloy, austenitic
stainless
40
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
Porte du Breuil - BP 34
71201
71201 LE CRUUSOT CEDEX
Le Creusot Cedex
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Normal Strength
Higher Strength
Austenitic Stainless
A, B, D, E
FH32, FH36
AH32, AH36, DH32, DH36, EH32, EH36
360, 410, 360FG, 410FG, 460FG, 490FG
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,
LTEH36, 1.5Ni, 3.5Ni, 5Ni, 9Ni
304L, 316L
B.O.S. / Con Cast
Billets
Normal Strength
Normal Strength
As below
carbon, carbon-manganese
A
A
Fabricated Sections
Normal Strength
Higher Strength
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
16
14
Fabricated Sections
Normal Strength
Higher Strength
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
16
16
Steelmaking
Semi-Finished
Sections
E.A.F./A.O.D./Con Cast
Billets
Austenitic Stainless
Duplex Stainless
Austenitic Stainless
Duplex Stainless
Machinery
As below
As below
304L, 316L, 321
UNS S31803
304L, 316L, 321
UNS S31803
austenitic stainless, duplex stainless, martensitic
stainless*
Tel No 33 3 8580 5575
Fax No. 33 3 8580 5211
Email: charlene.janaudy@arcelormittal.com
Web: www.industeel.info
Certificate number MD00/3227/0004/1 Expiry Date: 02/03/2018
Ingots also in martensitic stainless steel up to 40 T for approved applications
INDUSTEEL FRANCE, site du Creusot
Lyon
Plates
Boiler & Pressure Vessel
Ferritic Low Temperature
150
50
150
100
50
50
56 rue Clemenceau - BP19
71201
Tel: +33 3 8580 5575 Fax: +33 3 8580 5211
Email: mailto: charlene.janaudy@arcelormittal.com
Web: http://www.industeel.info
Plates with specified through thickness properties.
Certificate #: MD00/1822/0008/1 Expiry date: 26/02/2018
LAMINES MARCHANDS EUROPEENS
Lyon
Steelmaking
Semi-Finished
Sections
Bars
200
13
30
2, Rue Emile Zola
59125 Trith St Léger
Tel +33 (0)3 2714 2270 Fax +33 (0)3 2714 2010 Email: mailto:e.cotton@lme.fr
Certificate #: MD00/1395/0007/1 Expiry date: 19/10/2016
LORRAINE TUBES
Lyon
100, rue du Maréchal Foch
54720 Lexy
Tel No: +33 382 252 252
Fax No: +33 382 252 116
Email: dmartini@lorraine.condesa.com
Web: www.condesa.com
Certificate No: MD00/4281/0001/ 1 Expiry Date: 17/01/2017
LORRAINE TUBES
Lyon
Route du Contez
57480 Rettel
Tel No: +33 382 252 225 Fax no: +33 382 252 116
Email: dmartini@lorraine.condesa.com
Web: www.condesa.com
Certificate No: MD00/4282/0001/1 Expiry Date 17/01/2017
UGITECH S.A.
Lyon
Bars
205
32
32
130
130
95
Avenue Paul Girod,
73403 UGINE Cedex
Tel: +33 4 79 89 32 92 Fax: +33 4 79 89 34 74
email: laurent.prost@ugitech.com web: www.ugitech.com
Certificate #: MD00/1583/0007/1 Expiry Date: 23/08/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
31
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Bremerhaven
Steelmaking
Semi-Finished
Hot Rolled Coil
B.O.S. / Con Cast
Slabs
Normal Strength
Boiler & Pressure Vessel
As below
As below
A, B, D
360, 410, 360FG, 410FG
220
20
20
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Blooms
Billets
As below
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
385
130
Steelmaking
Plates
B.O.S./Ingot/Con Cast
Normal Strength
Higher Strength
As below
A, B, D, E
FH32, FH36
AH40, DH40, EH40, EH46S, FH46S
EH46, FH46
AH32, AH36, DH32, EH32
DH36, EH36
360FG, 410FG, 460FG, 490FG, 510FG
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,
LTEH36, LTFH32, LTFH36, 5Ni
Germany
ARCELORMITTAL BREMEN GmbH
Carl-Benz- Straße 30
D-28237 Bremen
Tel +49 421 648 2306 Fax +49 412 648 49 2306
email: salesflat.germany@arcelormittal.com web: www.arcelormittal.com/bremen
Certificate No. MD00/0857/0006/1 Expiry date: 17/10/2016
ARCELORMITTAL RUHRORT GmbH
Hamburg
Vohwinkelstraße 107
D-47137 Duisburg
Tel 0049 (0) 203 606 66302 Fax 0049 (0) 203 606 66 362
email: c.vonlivonius@arcelormittal.com
Web http://www.arcelormittal.com
Certificate Number: MD00/3631/0003/1 Expiry date: 24/07/2017
Aktiengesellschaft der Dillinger Hüttenwerke
Hamburg
Boiler & Pressure Vessel
Ferritic Low Temperature
170
50
100
110
170
220
100
50
Hüttenwerkstrasse
Postfach 1580
D-66748 Dillingen / Saar
All plates with specified through thickness properties.
Tel: +49 6381 474735 Fax: +49 6831 473224
email: hermann.ludwig@dillinger.biz web:: www.dillinger.biz
Certificate No. MD00/0361/00014/1 Expiry date: 19/09/2017
BENTELER STEEL/TUBE GmbH
Hamburg
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Slabs
Blooms/Billets
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
215
310
Niederdarmer Straße 5
D-49811 Lingen
Tel: +49 591 80004 800 Fax: +49 591 80004 460
Email to: Luben.Savov@benteler.de
Web: http://www.benteler.com
Certificate No. MD00/1805/0007/1 Expiry date: 10/10/2017
Steelmaking and semi-finished slabs, blooms and billets intended for plates, forgings and tubes.
Semi-finished products in carbon, carbon-manganese and alloy steel: slabs to 670mm wide, to 11,500mm long to 12.8 tonnes and blooms/billets of dimensions
300mm x 230mm or 310mm round of maximum length 12,800mm
BGH EDELSTAHL FREITAL GmbH
Hamburg
Steelmaking
Semi-Finished
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Slabs
Billets
Semi-finished Products
Machinery
Bars
As below
alloy, stainless steel, austenitic stainless, duplex
stainless
stainless steel
As below
alloy, austenitic stainless
alloy, austenitic stainless, duplex stainless,
martensitic stainless*
12
230
120
160
165
Am Stahlwerk 1
D-01705 Freital
Tel: +49 (0)351 646 2232
Fax: +49 (0)351 646 2888
Email: mailto:steffen.Rehberg@bgh.de
Web: http://www.bgh.de
Including forged bars
Certificate No. MD00/1973/0008/1 Expiry date: 05/08/2017
BGH EDELSTAHL SIEGEN GmbH
Hamburg
Steelmaking
Semi-Finished
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
E.A.F./V.O.D./Ingot
Ingots (tonnes)
32
As below
martensitic stainless
austenitic stainless, duplex stainless
carbon, carbon-manganese, alloy
28
35
51
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Steelmaking
E.A.F. / Ingot
Bars
E.A.F./V.O.D./Ingot
Semi-finished Products
Machinery
carbon, carbon-manganese, alloy, austenitic
stainless
Martensitic stainless*
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
Industriestraße 9,
D-57076
Siegen
Tel No. +49 (0)271 701- 341 Fax No. +49 (0) 271 701376
Email peter.scheer@bgh.de
Web www.bgh.de
Certificate No MD00/3767/0005/1
Expiry date: 30/03/2019
BUDERUS EDELSTAHL GmbH
Hamburg
200
190
Buderusstraße 25
D-35573 Wetzlar
Tel: +49 (0)6441 374 2505 Fax: +49 (0)6441 374 2681 Email: eckard.keunecke@buderus-steel.com
Web: http://www.buderus-steel.com
Certificate No. MD00/0257/0010/1 Expiry date: 07/07/2017
DEUTSCHE EDELSTAHLWERKE GMBH
Hamburg
Steelmaking
E.A.F. / Con Cast
E.A.F. / Ingot
Structural
Bars
Machinery
As below
As below
carbon, carbon-manganese, alloy, austenitic
stainless
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless, martensitic stainless*
80
80
Works Siegen
Obere Kaiserstraße
D-57078 Siegen
Tel: +49 (0)271 808 26 94 Fax: +49 (0)271 808 25 01 Email: mailto:andreas.prause@dew-stahl.com Web: http://www.dew-stahl.com
Certificate No. MD00/0901/0009/1 Expiry date: 11/07/2017
DEUTSCHE EDELSTAHLWERKE GMBH
Hamburg
Steelmaking
Semi-Finished
Bars
E.A.F. / Con Cast
E.A.F. / Ingot
Ingots (tonnes)
Semi-finished Products
Structural
Machinery
As below
As below
carbon, carbon-manganese, alloy, stainless steel
carbon, carbon-manganese, alloy, austenitic
stainless
alloy, austenitic stainless
alloy, austenitic stainless, duplex stainless,
martensitic stainless*
66
250
250
250
Works Witten
Auestraße 4
D-58452 Witten
Tel: +49 (0) 2302 292 437 Fax: +49 (0) 2302 294 008
email: stephanie.pueckel@dew-stahl.com web:www.dew-stahl.com
Certificate No. MD00/2075/0012/1 Expiry date: 19/01/2019
GEORGSMARIENHÜTTE GmbH
Hamburg
Steelmaking
Semi-Finished
Chain Cable Stock
As below
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
A, B, D, E
AH32, AH36, DH32, DH36, EH32
alloy
carbon, carbon-manganese
U1, U2, U3, R3
Steelmaking
E.A.F. / Con Cast
As below
Bars
Structural
carbon, carbon-manganese, alloy
100
Machinery
carbon, carbon-manganese, alloy
50
Chain Cable Stock
U1, U2
73
Normal Strength
A
50
Bars
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Blooms
Normal Strength
Higher Strength
Structural
44
240
180
180
270
280
155
Neue Hüttenstraße 1
D-49124 Georgsmarienhütte
Tel: +49 (0)5401 39 4630 Fax: +49 (0)5401 39 4598
Email: andre.rademacher@gmh.de
Web: http://www.gmh.de
Certificate No. MD00/0596/0007/1 Expiry date: 02/10/2016
H.E.S. HENNIGSDORFER ELEKTROSTAHLWERKE
GmbH
Hamburg
Wolfgang-Küntscher-Straße 18
D-16761 Hennigsdorf
Tel: +49 (0)3302 806-728 Fax: +49 (0)3302 806-724
email: ingo.laudahn@rivagroup.com web: www.rivagroup.com
Certificate No. MD00/0665/0008/1 Expiry date: 30/06/2017
HOESCH SCHWERTER PROFILE GmbH
Hamburg
Sections
Eisenindustriestraße 1
D-58239 Schwerte
Tel: +49 (0)2304 106-340 Fax: +49 (0)2304 106-590
Email: info@tks-hho.thyssenkrupp.com
Web: http://www.hoesch-profile.de
Certificate No. MD00/0682/0007/1 Expiry date: 07/01/2018
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
33
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Hüttenwerke Krupp Mannesmann GmbH
Hamburg
Steelmaking
B.O.S. / Con Cast
Semi-Finished
Slabs
carbon, carbon-manganese, alloy, High-nickel
steel (for low temperature service)
carbon, carbon-manganese, alloy, high-nickel
steel (for low temperature service)
carbon, carbon-manganese, alloy
Blooms/Billets
Max Thickness/Diameter (mm)
260
406
Huckingen Works
Ehinger Strasse 200
D-47259 Duisburg-Huckingen
Tel: +49 (0)203 999-01 Fax: +49 (0)203 999-4411
Email: frank.rashewski@hkm.de
Web: http://www.hkm.de
Certificate No. MD00/0730/0008/1 Expiry date: 06/02/2018
ILSENBURGER GROBBLECH GmbH
Hamburg
Plates
Normal Strength
Austenitic Stainless
B, D, E
A
AH40, DH40, EH40, FH40
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36, FH27S, FH32, FH36
360AR, 410AR, 460AR
360, 410, 460, 490, 360FG, 410FG, 460FG, 490FG,
510FG
LTAH40, LTDH40, LTEH40, 1.5Ni, 3.5Ni, 5Ni,
9Ni
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
316L
E.A.F. / Con Cast
Blooms/Billets
Normal Strength
Machinery
As below
As below
A, B
carbon, carbon-manganese, alloy
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
85
150
100
120
40
100
50
120
80
Veckenstedter Weg
D-38871 Ilsenburg
All plates with specified through thickness properties.
Tel: +49 39452/85 5530 Fax: +49 39452/85 5733
email Manegold@ilsenburger-Grobblech.de web: www.ilsenburger-Grobblech.de
Certificate No. MD00/1654/0013/1 Expiry date: 23/02/2017
Lech-Stahlwerke GmbH
Hamburg
Steelmaking
Semi-Finished
Bars
240
100
90
Industriestrasse 1
D-86405 Meitingen
Tel: +49 (0) 8271/82-325 Fax: +49 (0) 8271/82-405 Email:mailto:jochen.henze@lech-stahlwerke.de Web: http://www.lech-stahlwerke.de
Certificate No. MD00/0921/0007/1 Expiry date: 02/11/2018
PEINER TRÄGER GMBH
Hamburg
Steelmaking
Sections
E.A.F. / Con Cast
Normal Strength
Higher Strength
As below
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
40
40
Plates
Normal Strength
Higher Strength
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
AH27S, DH27S, EH27S
460FG, 490FG, 510FG
360FG, 410FG
250
120
250
120
150
Gerhard-Lucas-Meyer Str. 10
D-31226 Peine
Tel: +49 5171 91 9543 Fax: +49 5171 91 9373
email: peiner.traeger@sz-ag.de web: www.peiner-traeger.de
Certificate No. MD00/3075/0006/1 Expiry date: 13/05/2019
REINER BRACH GmbH & Co. KG
Bremerhaven
Boiler & Pressure Vessel
Wilhelm-Karmann-Straße 5
D-28237 Bremen
Tel: +49 421 985 08-140 Fax: +49 421 985 08-149
Email: frank-santuari@brach.de
Web:http://www.brach.de
Certificate No. MD00/2631/0007/1 Expiry date: 31/12/2017
REINER BRACH GmbH & Co. KG
Wilhelm-Karmann-Straße 5
D-28237 Bremen
Bremerhaven
Semi-Finished
Ingots (tonnes)
carbon, carbon-manganese
43
Tel No +49 3364 37 81 54
Fax No +49 3364 37 81 55
Email: info@brach.de
Web: www.brach.de
Certificate No. MD00/4032/0004/1 Expiry Date 31/12/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
34
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
SAARSCHMIEDE GmbH FREIFORMSCHMIEDE
Hamburg
Steelmaking
EAF/LRF/VD/Ingot
Carbon, Carbon-manganese
Max Thickness/Diameter (mm)
56
Bars
Normal Strength
Chain Cable Stock
A
U1, U2, U3
40
40
Steelmaking
Semi-Finished
Bars
B.O.S. / Con Cast
Blooms/Billets
Normal Strength
Chain Cable Stock
As below
Normal Strength
A
U1, U2, U3
265
160
100
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Slabs
As below
carbon, carbon-manganese
350
Bismarckstraße 57-59
D-66330 Völklingen
Tel:+49 (0)6898 102650 Fax:+49(0)6898 104560
Email:mailto: m.lorinser@saarschmiede.com
Web:http://www.saarschmiede.com
Certificate No. MD00/2017/0002/1 Expiry date: 13/05/2017
SAARSTAHL AG
Hamburg
Works Neunkirchen
D-66511 Neunkirchen
Tel: +49 6898 104293 Fax: +49 6898 1054293
email: daniel.muecke@saarstahl.com web: www.saarstahl.com
Certificate No. MD00/1286/0007/1 Expiry date: 09/08/2017
SAARSTAHL AG
Hamburg
Works Völklingen
Bismarckstrasse 57 - 59
D-66330 Völklingen
Tel: +49 (0) 6898 104 293 Fax: +49 (0) 6898 105 4293
email: daniel.muecke@saarstahl.com web:www.saarstahl.com
Certificate Number: MD00/1931/0007/1 Expiry: 09/08/2017
SALZGITTER FLACHSTAHL GmbH
Hamburg
D-38239 Salzgitter,
Eisenhüttenstrasse 99,
Tel: +49 5341 21-3121 Fax: +49 5341 21-2510
Email: flachstahl@salzgitter-ag.com
Web: www.salzgitter-flachstahl.de
Approved slab section sizes up to 350 x 2600mm.
Steel types carbon and carbon-manganese cover the supply of slabs for processing into normal strength, high strength, boiler and pressure vessel grades and
ferritic steels for low temperature service according to the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The final
processing mill is responsible for ordering steel which complies with their approved chemical composition and enables them to achieve the required mechanical
properties.
Certificate No. MD00/3990/0002/4 Expiry date: 14/02/2018
SALZGITTER MANNESMANN GROBBLECH GmbH
Hamburg
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Austenitic Stainless
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG
304L, 316L
50
50
40
50
50
Wiesenstraße 36
D-45473 Mülheim an der Ruhr
Tel: +49 (0)208 458 458 4510 Fax: +49 (0)208 458 1827
email: mareike.kirch@smgb.de web: www.smgb.de
Certificate No. MD00/1806/0007/1 Expiry date: 27/04/2017
SCHMIEDEWERKE GRÖDITZ GmbH
Hamburg
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy, austenitic
stainless
E.A.F./V.O.D./Ingot
Ingots (tonnes)
As below
duplex stainless
84
Riesaer Straße 1
D-01609 Gröditz
Tel: +49 35 263 62-613 Fax: +49 35 263 62-622
email: thomas-jakubowski@stahl-groeditz.de web: www.stahl-groeditz.de
Certificate No. MD00/2880/0006/1 Expiry date: 11/04/2017
Including ESR ingot and the supply of liquid steel to Stahlguss Groditz GmbH.
SILBITZ GUSS GmbH
Hamburg
Steelmaking
Semi-Finished
7
Dr. - Maruschky- Straße 2
D-07613 Silbitz/Thüringen
Tel: +49 (0)3 6693 80-250 Fax: +49 (0)3 6693 80251
email: mailto: jfriede@silbitz-guss.de web: www.silbitz-guss.de
Certificate #: MD00/1382/0002/1 Expiry date: 31/08/2017
Ingot approval covers duplex and superduplex grades.
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
35
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
STAHLWERK BOUS GMBH
Hamburg
Steelmaking
Semi-Finished
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Billets
carbon, carbon-manganese, alloy
carbon, carbon-manganese
carbon, carbon-manganese, alloy
Max Thickness/Diameter (mm)
60
430
P/O Box 1243
D-66359 Bous/Saar
Tel: +49 6834 81286 Fax: +49 6834 81586 Email: mailto:mmuth@stahlwerk-bous.de
Ingots up to 60 tonne and 2300 mm dia.
Con cast billets approved to 430 x 320mm.
Web http://www.stahlwerk-bous.de
Certificate #: MD00/1249/0006/1 Expiry date: 20/08/2016
STAHLWERK THÜRINGEN GMBH
Hamburg
Steelmaking
Sections
E.A.F. / Con Cast
Normal Strength
Higher Strength
As below
A, B
AH32, AH36, DH32, DH36
Steelmaking
Bars
E.A.F. / Ingot
Structural
As below
carbon, carbon-manganese, alloy, austenitic
stainless
50
Hot Rolled Coil
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Normal Strength
Higher Strength
Boiler and Pressure Vessel
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG
A, B, D, E
AH27S, DH27S, AH32, DH32, AH36, DH36
410 FG, 460 FG, 360 FG, 360, 410, 490FG, 510FG
20
20
20
20
20
20
Steelmaking
Semi-Finished
Hot Rolled Coil
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
Normal strength, Higher Strength
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG
255
20
20
20
Steelmaking
Hot Rolled Coil
B.O.S. / Con Cast
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG
20
20
20
Plates
Normal Strength
Higher Strength
A, B, D, E
FH27S, FH32, FH36
AH40, DH40, EH40
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36, 5Ni, 9Ni
UNS S31803
A, B, D, E
AH27S, DH27S, AH32, DH32, AH36, DH36,
EH27S, EH32, EH36
360 FG, 460 FG, 410 FG, 360, 410, 490FG, 510FG
25
25
Kronacher Straße 6
D-07333 Unterwellenborn
Tel +49 3671 455006010 Fax +49 3671 45507710
Email: gerd.hoffmann@stahlwerk-thuringen.de
Web http://www.stahlwerk-thueringen.de
Certificate #: MD00/1424/0008/1 Expiry date: 19/11/2015
Schmidt + Clemens GmbH +Co. KG
Hamburg
Kaiserau 2
D-51789 Lindlar
Tel: +49 (0)22 66 9230 Fax: +49 (0)22 66 928230
Email: mailto:g.bach@schmidt-clemens.de
Web http://www.schmidt-clemens.de
Certificate #: MD00/1319/0008/1 Expiry date: 10/10/2016
THYSSENKRUPP STEEL EUROPE AG
Hamburg
Plates from coils
Works Bochum
Kaiser-Wilhelm-Straße 100
D-47166 Duisburg
Tel: +49 (0)203 52-45582 Fax: +49 (0)203 52-43568
web: www.thyssenkrupp-steel-europe.com
Certificate No. MD00/0899/0008/1 Expiry date: 23/08/2017
THYSSENKRUPP STEEL EUROPE AG
Hamburg
Works Beeckerwerth
Tel: +49 (0)203 52-23456 Fax: +49 (0)203 52-42100
Web: www.thyssenkrupp-steel-europe.com
Certificate # MD00/1823/0008/1 Expiry date: 18/08/2017
THYSSENKRUPP STEEL EUROPE AG
Hamburg
Works Bruckhausen
Tel: +49 (0)203 52-25591 Fax: +49 (0)203 52-25594
web: www.thyssenkrupp-steel-europe.com
Certificate No. MD00/1824/0008/1 Expiry date: 24/08/2017
THYSSENKRUPP STEEL EUROPE AG
Hamburg
Boiler & Pressure Vessel
Ferritic Low Temperature
Plates from coils
Duplex Stainless
Normal Strength
Higher Strength
Boiler and Pressure Vessel
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
36
150
50
60
100
40
100
50
35
20
20
20
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
Works Duisburg-Süd
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Tel: +49 (0)203 52-45582 Fax: +49 (0)203 52-45568
Web: www.thyssenkrupp-stahl.com
Certificate No. MD00/1825/0011/1 Expiry date: 18/08/2017
Specified through thickness properties on all normal and higher strength steel grade plates.
India
AMBICA STEELS LIMITED
Mumbai
Steelmaking
Semi-Finished
Bars
A.O.D./Con Cast
Billets
Austenitic Stainless
Duplex Stainless
As below
austenitic stainless, duplex Stainless
304L, 316L
UNS S31803
250
125
125
51/2, Site IV,
Industrial Area,
Sahibabad-201010,
Ghaziabad,
Uttar Pradesh
Tel: +91 9811 045363 Fax: +91 4189366
web: www.ambicasteels.com
Certificate No: MD00/4531/0001/1 Expiry Date: 01/12/2018
Approval for bars includes Bright Bars.
Approval covers IF/AOD steelmaking and concasting at the above address and also rolling and heat treatment activities at Plot No.-32, Site II, Loni Road
Industrial Area, Mohan Nagar, Ghaziabad-201 007, Uttar Pradesh.
ARCVAC FORGECAST LTD
Chennai
Steelmaking
Semi-Finished
EAF/LRF/VD/Ingot
Ingots (tonnes)
Carbon, Carbon-manganese, Alloy
carbon, carbon-manganese, alloy
Steelmaking
Semi-Finished
Bars
E.A.F. / Con Cast
Billets
Chain Cable Stock
As below
carbon, carbon-manganese
U1, U2, U3
10
NH 2, Durgapur Expressway
P.O: Panchghara
Hooghly.
West Bengal - 712 306
Tel: + 91 33 2600 2176; Fax + 91 33 2659 8002
Email: swapan@smithy.in
Web: www. arcvacsteel.com
Certificate No. MD00/3561/0004/1 Expiry date: 06/02/2018
BHUSHAN POWER & STEEL LIMITED
Chennai
200
90
Vill. Thelkoli, P.O. Lapanga,
Tehsil - Rengoli,
Distt. Sambalpur - 768 232,
Tel: +91 663 253 5000 / 256 2026-32 Fax: +91 663 256 2007 / 256 2011 Email: Orissa@bpsl.net Web: http://www.bpsl.net
Billets as semi-finished products nominal 200mm maximum width x nominal 12000mm maximum length are approved for further processing for rolled products.
Bars for Grades U1 and U2 accepted for end use in the normalised condition; bars for Grade U3 accepted for end use in the quenched and tempered condition.
Certificate Number: MD00/4178/0001/1 Expiry: 10/06/2016
CHANDAN STEEL LIMITED
Plot 31, 32, 33B, 35, 36
GIDC Umbergaon Dist.
Valsad
Gujarat 396171
Mumbai
Steelmaking
A.O.D./Ingot/Con Cast
austenitic stainless steel, as below
200
As below
Normal strength, Higher Strength
A, B
AH27S, AH32, AH36, DH27S, DH32, DH36
360FG, 410FG
A, B
AH27S, DH27S, AH32, DH32, AH36, DH36
260
20
20
20
20
20
Admin Office: Tel: +91 22 66290600, Fax: +91 22 66290633/34 Email to: csl@chandansteel.net
Works: Tel: +91 260 3089999, Fax: +91 260 2562287/2560103 Email to: exports@chandansteel.net
Website: www.chandansteel.net
Certificate No. MD00/4376/0001/1 Expiry date: 08/07/2017
CCM Billets 100 to 200mm square of various sections cast from 4m to 9mm in length
Ingots of maximum weight 2500kg
ESSAR STEEL INDIA LTD.
Mumbai
Steelmaking
Semi-Finished
Hot Rolled Coil
Plates from coils
E.A.F. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Normal Strength
Higher Strength
Hot Strip Mill
Hazira - 394270
District Surat
Gujarat
Tel: +91 261 6683902/6683142
Email mailto: Rajat.Gupta@essar.com Web http://www.essar.com
Slabs as semi finished products nominal maximum width 2040mm x nominal maximum length 4900mm to the above maximum thickness are approved for
further processing for rolled products.
Certificate No. MD00/2091/0009/1 Expiry date: 05/06/2018
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
37
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
ESSAR STEEL INDIA LTD.
Mumbai
Plates
Normal Strength
Boiler & Pressure Vessel
E
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360FG, 410FG
100
E.A.F. / Con Cast
Blooms
Bars
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
225
150
E.A.F./A.O.D./Con Cast
E.A.F./V.O.D./Con Cast
Slabs
Austenitic Stainless
austenitic stainless
austenitic stainless
As below
304L, 316L, 317L, 321, 347
160
53
B.O.S./E.A.F./Con Cast
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As Below
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
360AR, 410AR, 460AR, 360, 410, 460, 490, 360FG,
410FG, 460FG, 490FG
B.O.S. / Con Cast
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
460FG, 490FG, 510FG
360FG, 410FG
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Normal Strength
Higher Strength
As below
Normal strength, Higher Strength
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
A, B, D, E
AH32, DH32, AH36, DH36, EH32, EH36
Higher Strength
Max Thickness/Diameter (mm)
70
100
70
Plate Mill Division
Tel: +91 261 668 3902 or 6739 Fax: +91 261 668 6739
email maneesh.moti@essar.com web www.essar.com
Certificate Number: MD00/3979/0005/1 Expiry: 16/01/2018
All plates are restricted to a maximum width of 4550mm.
ISMT LIMITED (STEEL PLANT)
Mumbai
Steelmaking
Semi-Finished
Morgaon Road
Jejuri 412 303
Purandara, Pune
Maharashtra
Tel: +91-020-414 34100
Fax: +91-020-26630779
Email mailto: ln.hegde@ismt.co.in
Web http://www.ismt.com
Certificate number. MD00/3816/0002/1
Expiry date: 23/08/2016
JINDAL STAINLESS LIMITED
Mumbai
Steelmaking
Semi-Finished
Plates
Post Box No. 6
O.P. Jindal Marg
Hisar Haryana State
India Pin 125 005
Tel: +91 98960 95029
email: hsr.maheshwari@jslhsr.com web: www.jslstainless.com
Certificate No. MD00/3110/0004/1 Expiry date: 21/10/2016
JINDAL STEEL & POWER LIMITED
Mumbai
Steelmaking
Plates
80
80
80
Raigarh
Post Box No.16
Kharsia Road
Raigarh 496001 Chattisgarh
Tel: +91 7762 227001 10 Fax: +91 7762 227021/22 Email to rksaini@jspl.com
Certificate No. MD00/3542/0003/1 Expiry date: 01/08/2017
JINDAL STEEL & POWER LIMITED
Mumbai
Steelmaking
Plates
80
70
70
80
ORISSA
SH - 63, Village - Nisha
Chendipada Road, Jindal Nagar
Angul - 759111
Tel: +91 9777445310
email: dinesh.tripathi@angul.jspl.com web: www.jindalsteelpower.com
Certificate No. MD00/4577/0001/1 Expiry date: 17/05/2019
JSW STEEL Ltd.
Mumbai
Steelmaking
Semi-Finished
Hot Rolled Coil
Plates from coils
220
20
20
20
20
Vijayanagar Works,
Vidyanagar,
Bellary,
Karnataka,
Tel: +91 22 42863005 Fax: +91 22 42863000
email: hemang.oza@jsw.in web: www.jsw.in
Certificate No: MD00/4514/0001/1 Expiry Date: 04/10/2018
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
38
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
KALYANI CARPENTER SPECIAL STEELS PRIVATE
LTD.
Mumbai
Steelmaking
E.A.F./Ingot/Con Cast
As below
Semi-Finished
Ingots (tonnes)
carbon, carbon-manganese, alloy
4
Blooms
carbon, carbon-manganese, alloy
320
Bars
carbon, carbon-manganese, alloy
250
Structural
carbon, carbon-manganese, alloy
150
Bars
Max Thickness/Diameter (mm)
Mundhwa
Pune 411 036
Maharashtra
Tel: +91 20 6621 5000 Fax: +91 20 2682 4483
Email: nitinbhat@kcssl.com Web: http://www.kalyanicarpenter.com
Approved for ingots as semi-finished products to the above maximum weight nominal 540/700mm diameter x 1770mm long 540/700 and blooms to the above
maximum thickness nominal 400mm wide x 10,000mm.
Certificate Number: MD00/0815/0008/1 Expiry: 22/08/2015
MAHINDRA SANYO SPECIAL STEEL PVT. LTD.
Mumbai
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
Normal Strength
Normal Strength
As below
carbon, carbon-manganese, alloy, austenitic
stainless
carbon, carbon-manganese, alloy, austenitic
stainless steel
A
A
50
200
Duplex Stainless
UNS S31803
120
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
As below
Normal strength, Higher Strength
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
460FG, 490FG, 510FG
360AR, 410AR, 360, 410
360FG, 410FG
Blooms/Billets
Sections
Bars
13
260
Khopoli Works
Jagdish Nagar
Khopoli
Dist. Raigad
Maharashtra 410 216
Tel: +91(0)2192 260500 Fax: +91 (0)2192 262496 Mobile: +91 830882 8540
Email mailto: dande.prashantr@mahindra.com
Web www.muscoindia.com
Certificate No. MD00/0971/0009/1 Expiry date: 15/07/2018
PRECISION METALS
Mumbai
Bars
Plot No. 253
Takai-Adoshi Road,
Atkargaon, Khopoli-410203,
Taluka-Khalapur, Dist- Raigad,
Maharashtra,
Tel: +91 21 92 304800 Fax: +91 21 92 304915
email: bbqc@venuswires.com web: www.venuswires.com
Certificate No: MD00/4590/0001/1 Expiry Date: 04/07/2019
Approved for bright round bars to above maximum diameter.
Scope of approval does not include steelamaking or rolling operations.
STEEL AUTHORITY OF INDIA LTD.
Mumbai
Steelmaking
Semi-Finished
Plates
Boiler & Pressure Vessel
250
75
50
50
63
75
Bhilai Steel Plant
Bhilai 490 001
Chhattisgarh
Tel +91 940 7981698
Fax +91 788 2222040 Email:mailto:klbalasubramanian@@sail-bhilaisteel.com
Web: sail-bhalaisteel.com
Certificate No. MD00/1433/0009/1 Expiry date: 27/04/2017
STEEL AUTHORITY OF INDIA LTD.
Chennai
Steelmaking
Plates
B.O.S. / Con Cast
Normal Strength
Boiler & Pressure Vessel
As below
A, B
360, 410, 360FG, 410FG
360AR, 410AR
52
35
40
As below
A
360AR, 410AR
A
50
50
12
Rourkela Steel Plant
Rourkela 769 011
Orissa
Tel: +91 (0) 661 244 7424 Fax +91 (0) 661 251 0183 email: sc.prasad@sailrsp.co.in Web: http://www.sail.co.in
Certificate Number: MD00/1434/0006/1 Expiry: 22/06/2016
TATA STEEL LIMITED
Chennai
Steelmaking
Plates
Hot Rolled Coil
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
B.O.S. / Con Cast
Normal Strength
Boiler & Pressure Vessel
Normal Strength
39
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
43 Chowringhee Road
Kolkata 700 071
LR Office
Product
Category
Grade
Steelmaking
IF/AOD/Ingot/ConCast
austenitic stainless steel
Semi-Finished
Blooms/Billets
austenitic stainless steel
Sections
Austenitic Stainless
304L, 316L, 321
Bars
Semi-finished Products
austenitic stainless
Max Thickness/Diameter (mm)
Tel: +91 (33) 657 664 8310 Fax: +91 (33) 22887255/22881396
Email mailto: rahul.lai@itd.tatasteel.com
Web http://www.tatasteel.com
Certificate No. MD00/1489/0007/1 Expiry date: 14/02/2018
VIRAJ PROFILES LIMITED (SMS, BAR AND
PROFILE DIVISION)
Mumbai
300
40
200
G-2,23,76, MIDC, TARAPUR INDUSTRIAL AREA
& SURVEY No 110, 111, 114/1, CD-116, 119 & 120,
GUT.No-25/1,25/2,26,27,31,33,34.
VILLAGE-MAHAGAON, DIST-PALGHAR
MAHARASHTRA - 401506
Tel: +91 90444 1039 Fax: +91 2525 260159
email mathur@viraj.com web: www.viraj.com
Certificate Number: MD00/2935/0005/1 Expiry date: 07/12/2017
316Ti austenitic stainless steel accepted for approved applications.
Billets and blooms as semi-finished products to the above maximum thickness, nominal 300mm wide x nominal 9000mm long are approved for further
processing for forged products.
Indonesia
PT. GUNAWAN DIANJAYA STEEL Tbk
Jakarta
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
B, D
A
AH27S, AH32, AH36, DH27S, DH32, DH36
360AR, 410AR
25
40
40
25
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Normal Strength
Higher Strength
Boiler & Pressure Vessel
A, B
AH36, AH40, DH36, DH40, EH36, EH40
360AR, 410AR
A, B
AH27S, AH32, AH36, DH27S, DH32, DH36
360AR, 410AR
50
50
40
16
14
16
B.O.S. / Con Cast
Slabs
Normal Strength
As below
Normal strength, Higher Strength
D
A, B
DH32, DH36
AH32, AH36
230
35
50
12
20
As below
Normal strength
A
A
200
25
25
JL. Margomulyo No.29A,
Tambak Sarioso,
Asemrowo,
Surabaya 60184
Tel: +62 31 7490598 Fax: +62 31 7490581/7482109
email: quality@gunawansteel.com web www.gunawansteel.com
Certificate No. MD00/1882/0009/1 Expiry date: 14/12/2018
PT. GUNUNG RAJA PAKSI
Jakarta
Plates
Hot Rolled Coil
JI. Imam Bonjol 4, Warung Bongkok
Desa Sukadanau, Clkarang Barat, Bekasi
West Java, Indonesia
Tel: +62 21 8900111 ext 3518 Fax: +62 21 8900333
Email: mailto:dewi.pl@grdsteel.com
Web: http://www.grdsteel.com
Certificate No. MD00/2749/0004/1 Expiry date: 14/11/2016
PT. KRAKATAU POSCO
Jakarta
Steelmaking
Semi-Finished
Plates
Higher Strength
Jalan Afrika No.2,
Kawasan Industri Krakatau,
Cilegon,
Banten, 42443
Tel: +62 (0)254 369416 Fax: +62(0)254 369799
email: agus.sk@krakatauposco.co.id web: www.krakatauposco.co.id
Certificate No.: MD00/4377/0001/1
PT. KRAKATAU STEEL (PERSERO) TBK.
Expiry Date: 25/08/2017
Jakarta
Steelmaking
Semi-Finished
Hot Rolled Coil
Plates from coils
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
E.A.F. / Con Cast
Slabs
Normal Strength
Normal Strength
40
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Jl. Industri No. 5
PO. Box 14
Cilegon 42435
Tel: +62 (0) 254 317274 Fax: +62 (0) 254 372608
email: handritoi.bharata@krakatausteel.com web: www.krakatausteel.com
Certificate Number: MD00/1183/0009/1 Expiry: 01/02/2018
Plates and coils in the supply condition TM+Acc Fine Grain Al+Nb are restricted to the thickness range 16.0 to 25.0mm.
Slabs as semi-finished products nominal maximum width 2000mm x and nominal maximum length 12000 mm to the above maximum thickness are approved for
further processing for rolled products.
Italy
A.B.S. Acciaierie Bertoli Safau S.p.A.
Venice
Steelmaking
Semi-Finished
Bars
E.A.F./Ingot/Con Cast
Rolled Bars
As Cast Round Section
Rolled Square Bars
Structural
Machinery
Chain Cable Stock
As below
Carbon, Carbon manganese, Alloy
Carbon, Carbon-manganese, Alloy
Carbon, Carbon-manganese, Alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
U1, U2, U3
R4
370
700
420
240
240
78
185
Via Buttrio, 28
33050 Pozzuolo del Friuli (UD)
Tel: +39 (0) 522 997200 Fax: +39 (0) 432 613 249
E-mail: claudia.lorenzi@arss.it Web: not yet avaliable
Address for Orders: Rubiera Special Steel SpA, Via XXV Aprile, 64, 42013, Casalgrande (RE), Italy
Certificate No. MD00/0019/0011/1 Expiry date: 14/06/2017
The approval for mooring chain cable stock grade R4 bars is restricted to the supply of 185mm maximum diameter bars to Vicinay Sestao S.L. and to 166mm
maximum diameter bars to Vicinay Cadenas S.A., Deusto Factory, to the applicable Vicinay purchasing specification MPR4. The approval covers the ingot cast
manufacturing route only.
ACCIAI SPECIALI TERNI S.p.A.
Venice
Steelmaking
Semi-Finished
Hot Rolled Coil
E.A.F./A.O.D./Con Cast
E.A.F./V.O.D./Con Cast
Slabs
Austenitic Stainless
austenitic stainless, As below
austenitic stainless
austenitic stainless
304L, 316L, 321
215
6
Viale B. Brin 218,
I 05100 Terni,
tel: +39 0744 4901 Fax: +39 0744 490904
email: commercialeterni.ast@acciaiterni.it web: www.acciaiterni.com
cert no: MD00/4414/0001/1
expiry date: 05/01/2018
Approval covers concast slabs to 215 x 1565 mm section size.
Approval includes proprietry 470 LI greade, accepted for approved applications only.
Approval includes 316 Ti and 309S grade to above thickness, accepted for approved applications only.
Approval includes above grades as cold rolled coil in solution treated condition to 3mm thickness.
ACCIAIERIA FONDERIA CIVIDALE S.P.A.
Trieste
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below, carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
35
Via delle Industrie No. 40
Zona Industriale
33043 Cividale del Friuli
(Udine)
Tel +39 432 706922 Fax +39 432 706920
email: afcspa@afcspa.com web www.cividalespa.com
Certificate No. MD00/3149/0005/1 Expiry date: 03/04/2017
Steel types carbon, carbon-manganese and alloy cover the supply of ingots for processing into forgings according to the Society's Rules for the Manufacture,
Testing and Certification of Materials, Chapter 5. The final processing mill is responsible for ordering steel which complies with their approved chemical
composition and enables them to achieve the required mechanical properties
ACCIAIERIE VALBRUNA S.P.A.
Venice
Steelmaking
Semi-Finished
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Billets
Bars
Machinery
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
41
As below
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless
austenitic stainless, precipitation hardened
stainless*, martensitic stainless*
duplex stainless
10
220
155
205
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
Viale Della Scienza, 25 z.i.
36100 Vicenza
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Tel: +39 0444 968211 Fax: +39 0444 968182
mail:quality@valbruna.it Web:http://www.acciaierie-valbruna.com
* Accepted for approved applications
Approval for Precipitation Hardened Stainless Machinery Bar is for Grade 17.4 PH, approval for Martensitic Stainless Machinery Bar is for Grade 431 and Grade
1.4418 Quenched and Tempered.
Duplex Stainless Steel bars are not approved for use in welded construction, and weld repair is not permitted.
Approval of Con cast material is for the production of Austenitic Stainless Steels only.
Ingots as semi finished products nominal maximum dimensions 600mm x 530mm x 2060mm to the above maximum weight
Billets as semi finished products nominal maximum width 220mm x nominal maximum length 6500mm to the above maximum thickness
Certificate No. MD00/0041/0007/1 Expiry date: 01/06/2017
ACCIAIERIE VALBRUNA S.P.A.
Venice
Steelmaking
E.A.F./Ingot/Con Cast
A.O.D./Ingot/Con Cast
Machinery
As below
as below
austenitic stainless, duplex stainless,
precipitation hardened stainless*, martensitic
stainless*
E.A.F. / Con Cast
Blooms/Billets
As Cast Round Section
Semi-finished Products
Structural
Machinery
carbon, carbon-manganese, alloy
carbon, carbon manganese, Alloy
Carbon, Carbon-manganese, Alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
280
600
200
180
130
Steelmaking
Semi-Finished
Sections
E.A.F. / Con Cast
Slabs
Normal Strength
Higher Strength
As below
Normal strength, Higher Strength
A, B, D, E
AH32, AH36, DH32, DH36
220
20
20
Fabricated Sections
Normal Strength
Higher Strength
A, B, D
AH32, AH36, DH32, DH36
22
22
Steelmaking
E.A.F. / Ingot
E.A.F/A.O.D/Ingot
Ingots (tonnes)
carbon, carbon-manganese, alloy
As below
austenitic stainless
carbon, carbon-manganese, alloy
30
65
Normal Strength
Higher Strength
A
AH36, DH36, EH36
20
20
Bars
73
Via A Volta 4
39100 Bolzano
39100 Bolzano
* Accepted for approved applications
Tel; +39 (0)471 924111 Fax: +39 (0)471 924355
Email mailto:info@valbruna.it Web: http//www.acciaierie-valbruna.it
Certificate No. MD00/2994/0005/1 Expiry date: 25/06/2018
ACCIAIERIE VENETE S.p.A.
Venice
Steelmaking
Semi-Finished
Bars
Camin Works
Riviera Francia, 9
35020 Camin (Padova)
Tel +39 (0)49 8282 820 Fax +39 (0)49 8282 666
email: commercial.dep@acciaierievenete.com web: www.acciaierievenete.com
Approval does not cover bars with a diameter of less than 65mm.
Certificate No. MD00/0042/0007/1 Expiry date: 25/03/2018
AFV ACCIAIERIE BELTRAME S.p.A
Venice
Viale della Scienza 81/A
36100 Vicenza
Tel: +39 0444 967111 Fax: +39 0444 967282
email: info@beltrame.it web: www.grupobeltrame.com
ARMANDO CIMOLAI CENTRO SERVIZI Srl
Venice
Via Masieres, No.32
33080 San Quirino (PN)
Tel: +39 (0)434 919292 Fax: +39 (0)434 919266
email: accs_sanquirino@comolai.com
Certificate No. MD00/2620/0006/1 Expiry date: 30/11/2017
ASO SIDERURGICA S.p.A. UNIPERSONALE
Milan
Semi-Finished
Via Seriola no. 122
25035 Ospitaletto
Brescia
Tel: +39 (0)30 6841011-(0)30 6841165
Email: Info@aso.it
Fax: +39 (0)30 6841012
Web: http://www.asogroupsteel.com.
Certificate No. MD00/0020/0007/1 Expiry date: 14/04/2017
BAGLIETTO S.r.l.
Genoa
Fabricated Sections
Via Castelgazzo 11
Novi Ligure (AL)
Tel: +39 0143 318000 Fax: +39 0143 319252
web: www.bagliettosas.it
Certificate No. MD00/3910/0002/1
Expiry date: 15.05.2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
42
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
COGNE ACCIAI SPECIALI S.p.a
Milan
Steelmaking
E.A.F. / Con Cast
E.A.F. / Ingot
Ingots (tonnes)
Billets
austenitic stainless, duplex stainless
martensitic stainless*
austenitic stainless, duplex stainless
Martensitic Stainless Steel*
austenitic stainless, duplex stainless
Martensitic Stainless Steel*
Semi-Finished
Bars
Max Thickness/Diameter (mm)
4
160
270
220
Via Paravera,16
11100 AOSTA
Tel No: +39 165 3021 Fax no: +39 165 43779
Email: info@cogne.com
Web site: www.cogne.com
Certificate No.MD00/3809/0002/1 Expiry date 13/07/2016
FOMAS S.p.A.
Milan
ESR
Ingots
carbon, carbon-manganese, alloy, austenitic
stainless, duplex
125
Steelmaking
B.O.S. / Con Cast
As below
Semi-Finished
Slabs
Normal strength, Higher Strength
Plates
Normal Strength
A, B, D, E
80
Higher Strength
80
Normal Strength
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
A
10
Higher Strength
AH27S, AH32, AH36
10
Via Martiri della Liberazione, 17
23875 Osnago (LC)
Tel No +39 3999811
Fax No +39 3958487
email: sonia.proietti@fomas.it web: www.fomas.it
Certificate No MD00/0475/0004/1 Expiry 08/01/2019
ILVA SPA IN AMMINISTRAZIONE
STRAORDINARIA
Venice
Hot Rolled Coil
303
Taranto Works
Via Appia KM 648
74123 Taranto
Tel: +39 02 307 00 775 Fax: +39 02 307 00 285
Email: commerciale.lamiere@rivagroup.com
Web: http://www.rivagroup.com
Specified through thickness properties for grade D, E, AH, DH and EH notation Z35 may be added
Certificate No. MD00/2276/0007/1 Expiry date: 09/10/2018
INDUSTRIE RIUNITE ODELESI I.R.O S.p.A
Milan
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Billets
carbon, carbon-manganese
carbon, carbon-manganese
Steelmaking
E.A.F. / Ingot
carbon, carbon-manganese, alloy, austenitic
stainless
140
Via Brescia 12,
12-25076 - Odolo (BS)
Tel: 0365-826089, Fax No. 0365 - 860564
E-mail: bianchettifabio@iro-spa.it
Website: www.iro-spa.it
Certificate No. MD00/4589/0001/1 Expiry Date: 03/07/2019
LUCCHINI RS S.p.A.
Milan
Via G. Paglia N.45
24065 Lovere
Bergamo
Tel: +39 035 963520 Fax: +39 035 963488 Email: mailto: a.carrara@lucchiniRS.it
Certificate No. MD00/0949/0008/1 Expiry date: 18/03/2018
METINVEST TRAMETAL S.p.A.
Trieste
Web: http://www.lucchiniRS.it
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG
60
60
60
Via Enrico Fermi, 44
33058 San Giorgio di Nogaro (UD)
Tel: +39 010 57 62911 Fax: +39 010 57 62990
email: rre@trametal.it web: www.trametal.it
Certificate No. MD00/2004/0008/1 Expiry date: 01/08/2017
Approved for Z grade plates with specified through thickness properties when tested in accordance with Rules requirements.
NLMK VERONA
Venice
Steelmaking
Semi-Finished
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
E.A.F. / Ingot
Ingots (tonnes)
43
As below
carbon, carbon-manganese, alloy
32
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Via A, Salieri, 22,
37050 Vallese di Oppeano (Verona)
Tel: +39 045 699 7900 Fax: +39 045 699 7901
email: verona@eu.nlmk.com Web: http://www.eu.nlmk.com/verona/
Round and Polygon ingots to nominal maximum dimensions of 1200mm diameter x 4750mm length, oblong ingots to nominal maximum dimensions 970mm x
870mm x 2050mm.
Certificate Number MD00/3985/0003/1 Expiry date: 30/01/2018
NUNKI STEEL SPA
Venice
Steelmaking
EAF/LRF/VD/Ingot
Carbon, Carbon-manganese, Alloy
40
Fabricated Sections
Normal Strength
Higher Strength
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
50
50
Sections
Normal Strength
Higher Strength
A, B, D
AH32, AH36, DH32, DH36
10
10
E.Fermi 33,
33058 San Giorgio Di Nogaro (UD),
Tel: 00 39 (0)431 623943 Fax: 00 39 (0) 431 623965
Certificate No.:MD00/4087/0002/1 Expiry Date: 05/11/2018
OFFICINE NORD EST S.r.l
Venice
Via Ungaresca No.12
33080 San Quirino (Pn)
Tel: +39 (0)434 919091 Fax: +39 (0)434 918646
email: info@officinenordest.it
Certificate No. MD00/2626/0007/1 Expiry date: 06/12/2017
Approved welding process - SAW
Approved weld type - Fillet weld only
OLIFER SRL
Milan
Via G. Marconi 4
25076 Odolo (BS)
Tel +39 365 826088
Fax +39 365 860727
Email: mailto: mg.comelli@mail.olifer.com Web:http://www.olifer.com
Certificate No. MD00/4485/0001/1 Expiry date: 30/03/2018
OLIFER-ACP S.P.A.
Milan
Steelmaking
Semi-Finished
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Blooms/Billets
As below
carbon, carbon-manganese, alloy
carbon, carbon-manganese
Fabricated Sections
Normal Strength
Higher Strength
A
AH32, AH36
DH36
54
120
STEELMAKING
Bergamo Works
Loc. Motta Alta 14
Cividate Al Piano
Bergamo
Tel: +39 363 97193/4 Fax: +39 363 976666
Email: mailto:direzione-cividate@olifer.com
Web http://www.olifer.com
Certificate No. MD00/1807/0008/1 Expiry date: 10/03/2018
PALESCANDOLO SPA
Naples
25
25
30
Via Boscofangone, zone A.S.I., Nola
Tel. no. +39 0817340800; Fax. no.: +39 0817340454 Email: ppalesc@tin.it; web: www.palescandolo.it
Certificate No. MD00/3850/0002/1
Expiry date: 30/10/2016
RUBIERA SPECIAL STEEL S.p.A.
Venice
Steelmaking
Semi-Finished
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Bars
As below
carbon, carbon-manganese, alloy, Normal
Strength, Higher Strength
carbon, carbon-manganese, alloy, Normal
Strength, Highrer Strength
100
180
Via 25 Aprile, 64
42013 Casalgrande (RE)
Tel: +39 0522 997232 Fax: +39 0522 840040
E-mail: inf@arss.it & angelo.vassetta@srss.it
Website: www.arss.it
Address for orders: Rubiera Special Steel S.p.A. , Via Adda, 23, 2305, Nuova Olonio di Dubino, Italy.
Ingots as semi finished products nominal maximum diameter 1935mm x nominal maximum height 5250mm to the above maximum weight in normal strength
and higher strength grades are approved for further processing for rolled products and in carbon, carbon-manganese & alloy grades are approved for further
processing for forgings.
Bars as semi finished products nominal maximum length 9500mm to the above maximum thickness in normal strength and higher strength grades are approved
for further processing for rolled products and in carbon, carbon-manganese & alloy grades are approved for further processing for forgings.
Certificate Number: MD00/0038/0008/1 Expiry: 06/03/2019
SIDERVAL S.P.A.
Milan
Sections
Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
30
Via Chini Battista 60
23018 Talamona (SO)
Tel: +39 342 674152 Fax: +39 342 670400
Email: mailto:raimondo.mariolil@siderval.it
Web: http://www.siderval.it
Certificate No. MD00/2857/0005/1 Expiry date: 15/01/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
44
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Kobe
Steelmaking
E.A.F. / Con Cast
E.A.F. / Ingot
Blooms/Billets
Bars
Normal Strength
Austenitic Stainless
Structural
Machinery
Chain Cable Stock
carbon, carbon-manganese,
carbon, carbon-manganese,
carbon, carbon-manganese,
carbon, carbon-manganese,
A
304L, 316L
carbon, carbon-manganese
alloy, austenitic stainless
carbon, carbon-manganese
U1, U2, U3
Bars
Austenitic Stainless
304L, 316L
Steelmaking
Plates
E.A.F. / Con Cast
Normal Strength
Boiler & Pressure Vessel
As below
A, B
360AR, 410AR
Japan
AICHI STEEL CORPORATION
Semi-Finished
Bars
alloy
austenitic stainless
alloy
alloy
480
190
180
180
190
125
190
120
Chita Plant
1, Wano-Wari
Arao-machi
Tokai-shi
Aichi-ken, 476-8666
Tel: +81 52 603 9353 Fax: +81 52 603 9898
email: hayashida@he.aichi-steel.co.jp web: www.aichi-steel.co.jp
Certificate No. MD00/0076/0009/1 Expiry date: 23/09/2018
AICHI STEEL CORPORATION
Kobe
150
Kariya Plant
3-6, Toyota-cho
Kariya-shi
Aichi-ken
448-0848
Tel +81 566 21 9130 Fax +81 566 23 6925
email: ymatsuoka@he.aichi-steel.co.jp web www. aichi-steel.co.jp
Certificate No. MD00/0078/0007/1 Expiry date: 22/09/2018
CHUBU STEEL PLATE CO., LTD.
Kobe
50
40
5-1, Kousudori
Nakagawa-ku
Nagoya
Tel: +81 52 661 3818 Fax: +81 52 661 2265 Email: mailto:aki-onozato@chubukohan.co.jp Web http://www.chubukokan.co.jp
Certificate No. MD00/0309/0007/1 Expiry date: 19/04/2017
DAIDO STEEL CO., LTD.
Kobe
Steelmaking
Semi-Finished
Bars
E.A.F. / Ingot
Ingots (tonnes)
Blooms
Billets
Structural
As below
carbon, carbon-manganese
carbon, carbon-manganese
carbon, carbon-manganese
carbon, carbon-manganese
Steelmaking
E.A.F. / Ingot
carbon, carbon-manganese, alloy
E.A.F. / Con Cast
Slabs
Normal Strength
Normal Strength
Chain Cable Stock
As below
carbon, carbon-manganese
A
A
U3
U1, U2
7
275
148
270
Chita Plant
39, Motohama-machi
Tokai-shi
Aichi-ken
Tel: +81 562 33 3106 Fax: +81 562 33 6598
email: y-hagama@ac.daido.co.jp web: www.daido.co.jp
Certificate No. MD00/0372/0006/1 Expiry date: 20/03/2017
DAIDO STEEL CO., LTD.
Yokohama
Shibukawa Plant
500, Ishihara
Shibukawa-shi
Gunma 377-0007
Tel: +81 279 25 2009 Fax: +81 279 25 2043 Email: mailto:t-furuse@ac.daido.co.jp
Certificate No. MD00/0375/0008/1 Expiry date: 25/11/2018
GODO STEEL LTD.
Kobe
Steelmaking
Semi-Finished
Sections
Bars
490
15
150
100
150
2946 Nakashima Shikamaku
Himeji-city
Hyogo pref.
Tel. +81 (0)79 234 9332 Fax +81(0)79 234 9538 Web: http://www.godo-steel.co.jp
Certificate No. MD00/0606/0007/1 Expiry date: 05/08/2018
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
45
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
HITACHI METALS, LTD.
Kobe
Steelmaking
Bars
E.A.F. / Ingot
Normal Strength
Structural
As below
A
alloy, austenitic stainless
Max Thickness/Diameter (mm)
150
150
Yasugi Works
2107-2, Yasugi-cho
Yasugi-shi
Shimane-ken
Tel: +81 (0) 854 22 1908 Fax: +81 (0)854 23 0218 Email mailto:hitoshi.yamasaki.rh@hitachi-metals.co.jp Web http://www.hitachi-metals.co.jp
Certificate No. MD00/0678/0007/1 Expiry date: 19/12/2018
JFE BARS & SHAPES CORPORATION
Kobe
Steelmaking
Semi-Finished
Sections
E.A.F. / Con Cast
Blooms
Billets
Normal Strength
Higher Strength
As below
Normal Strength, Higher Strength
Normal Strength, Higher Strength
B, D, E
A
EH32, EH36
AH32, AH36, DH32, DH36
300
150
25
32
25
32
Himeji Works
1280, Hosoe,
Shikama-ku, Himeji-City,
Hyogo-Pref. 672-8064,
Tel +81 (0)792 35 6376 Fax +81 (0)792 35 2048 email: mailto:masanobu-kimura@jfe-bs.co.jp Web: http://www.jfe-bs.co.jp
The scope of approval for semi-finished products includes for; billets nominal maximum width 150mm x nominal maximum length 8600mm; blooms nominal
maximum widths 220mm x nominal maximum length 10.000mm; approved for further processing for rolled products.
Certificate Number: MD00/1535/0007/1 Expiry: 26/08/2015
JFE BARS & SHAPES CORPORATION
Yokohama
Steelmaking
Semi-Finished
Sections
E.A.F. / Con Cast
Billets
Normal Strength
Higher Strength
As below
carbon, carbon-manganese
A
AH32, AH36, DH32, DH36
150
32
32
Kashima Works
7 Minamihama, Kamisu-city
Ibaraki Pref.
314-0111
Tel: +81 (0)299 90 5218 Fax: +81 (0)299 90 5201 Mob +81(0) 9050905201
Email: mailto:yuichiro-nishidate@jjfe-bs.co.jp
Web http://jfe-bs.co.jp
Semi finished products as billets to nominal 150mm width and 12000mm nominal length to the maximum thickness shown above are approved for further
processing for rolled products.
Certificate No. MD00/1920/0006/1 Expiry date: 28/01/2014
JFE STEEL CORPORATION
Kobe
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
B.O.S. / Ingot
Ingots (tonnes)
Slabs
Blooms
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
Austenitic Stainless
Clad
Tapered
Hot Rolled Coil
Sections
Bars
Differential Thickness
Normal Strength
Boiler & Pressure Vessel
Normal Strength
Higher Strength
Structural
Machinery
Chain Cable Stock
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
46
As below
As below
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
A, B, D, E
AH42, FH27S, FH32, FH36
DH42, DH46, DH50, DH55, DH62, DH69, EH42,
EH46, EH50, EH55, EH62, EH69
AH40, DH40, EH40
EH40S**
EH47
EH40S*
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
360, 410
360FG, 410FG, 460FG, 490FG, 510FG
9Ni
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
304L, 316L
E/304L, E/316L
A, B, D, AH27S, AH32, AH36, DH27S, AH40,
DH32, DH36, DH40, EH27S, EH32, EH36, EH40
A, B, D, AH27S, AH32, DH27S, DH32
A, B
360, 410
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
carbon, carbon-manganese
alloy
carbon-manganese
U1, U2
30
310
750
200
50
75
80
85
90
100
150
40
100
134
40
50
50
30
50
40
16
16
32
32
400
165
190
130
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
West Japan Works (Kurashiki)
1 Mizushima
Kawasaki-Dori
Kurashiki
Tel: +81 (0)86 447 2652 Fax: +81 (0)86 447 2735
email: y-kida@jfe-steel.co.jp www.jfe-steel.co.jp/works/west/
Certificate No. MD00/0838/0017/1 Expiry date: 14/10/2018
Ingot cast maximum thickness plate
200 mm.
Continuous cast maximum thickness plate:
Grade A Normalised: up to 200mm. Grades B and D Normalized: up to 155 mm. Other grades and conditions: up to 100mm.
Specified through thickness properties on all plate grades.
Thermo Mechanical
= TMCP
TM + Accelerated Cooling = TMCP
Tapered plates up to 8 mm/m taper ratio.
Differential thickness plates, differential thickness 8mm by TMCP, 5mm by Normalized rolling.
MQS Approved - Approval No. MQS 022
JFE STEEL CORPORATION
Kobe
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Slabs
Blooms/Billets
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
Austenitic Stainless
Clad
Differential Thickness
Hot Rolled Coil
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Sections
Normal Strength
Higher Strength
Ferritic Low Temperature
As below
carbon, carbon-manganese, Normal strength,
Higher Strength
carbon, carbon-manganese, Normal Strength,
Higher Strength
A, B, D, E
FH27S, FH32, FH36, FH40
EH40S*
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40, EH47
360AR, 410AR
460FG, 490FG, 510FG
360FG, 410FG
LTAH27S, LTAH32, LTAH36, LTAH40,
LTDH27S, LTDH32, LTDH36, LTDH40,
LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,
LTFH32, LTFH36
304L, 304LN, 316L, 316LN, 317L, 317LN
A to EH36/304L, A to EH36/316L
A, DH34S, B, D, A,B, AH32, AH36, DH32,
DH36, AH34S
A, B, D, E
AH27S, AH32
460FG, 490FG
360, 410, 360FG, 410FG
E
A, B, D
AH40, DH40, EH40, FH27S, FH32, FH36
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
LTAH27S, LTAH32, LTAH36, LTAH40,
LTDH27S, LTDH32, LTDH36, LTDH40,
LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,
LTFH32, LTFH36
300
250
120
80
85
100
40
55
70
40
55
30
50
12
8
8
12
18
35
18
36
18
West Japan Works (Fukuyama)
1, Kokan-cho
Fukuyama-city
Hiroshima-pref.
721-8510
Tel. (0)84 945 3160 Fax (0)84 945 3101
Email: k-nibu@jfe-steel.co.jp Web http://www.jfe-steel.co.jp
TM + Acc = OLAC process
For differential thickness plates, the maximum thickness differential for a thickness of 50mm is 10mm for normal strength grades and 6mm for higher strength
grades
Approved for the supply of plates with specified through thickness properties (Z25/Z35).
MQS Approved - Approval No. MQS 005
Certificate No. MD00/1055/0015/1 Expiry date: 14/10/2018
JFE STEEL CORPORATION
Yokohama
Steelmaking
Plates
B.O.S. / Con Cast
Normal Strength
Higher Strength
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
47
As below
A, B, D, E
FH27S, FH32, FH36
AH42, DH42, EH42
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40
100
42
83
90
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Yokohama
Plates
Boiler & Pressure Vessel
Max Thickness/Diameter (mm)
Japan
JFE STEEL CORPORATION
Tapered Plates max
Higher strength
360AR, 410AR
360, 410, 460FG, 490FG, 510FG
360FG, 410FG
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
D, E
A, B
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36, AH40, DH40, EH40
AH32, AH36
Steelmaking
Semi-Finished
B.O.S/V.O.D./Con Cast
Slabs
austenitic stainless
austenitic stainless
Steelmaking
B.O.S. / Con Cast
B.O.S. / Ingot
E.A.F. / Con Cast
E.A.F. / Ingot
Normal Strength
Higher Strength
Differential Thickness
Normal Strength
Boiler & Pressure Vessel
As below
As below
As below
As below
A, B, D, E
DH42, DH50, DH55, DH62, DH69, EH42, EH50,
EH55, EH62, EH69, FH40, FH42, FH46, FH50,
FH55, FH62, FH69
AH46, DH46, EH46
AH40, DH40, EH40
FH27S, FH32, FH36
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR, 460AR
360, 410, 460, 490, 460FG, 490FG, 510FG
360FG, 410FG
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
A,B, D,E, HTS up to EH36
A, B, D
360FG, 410FG
B.O.S./Ingot/Con Cast
Ingots (tonnes)
Rolled Blooms
Semi-finished Products
Normal Strength
Machinery
Chain Cable Stock
As below
carbon, carbon-manganese, alloy
Carbon, Carbon-Manganese, Alloy
carbon, carbon-manganese, alloy
A
carbon, carbon-manganese, alloy
U1, U2, U3
Ferritic Low Temperature
Tapered Plates max
Normal Strength
Higher Strength
40
50
100
42
40
50
50
22
East Japan Works (Keihin)
1-1, Ohgishima
Kawasaki-ku
Kawasaki
210-0868
Tel: +81 44 322 1185 Fax: +81 44 322 1510
Email: m-toyonaga@jfe-steel.co.jp
All plate grades with specified through thickness properties.
Materials Quality Scheme Approved - Approval No. MQS 034
Certificate No. D00/1056/0011/1 Expiry date: 28/10/2018
JFE STEEL CORPORATION
Yokohama
275
East Japan Works (Chiba)
1, Kawasaki-cho
Chuo-ku
Chiba 260-0835
Tel: +81 43 262 2287 Fax: +81 43 262 2980
email: mas-oota@jfe-steel.co.jp web: www.jfe-steel.co.uk
Certificate No.: MD00/4065/0002/1
KOBE STEEL, LTD.
Expiry Date: 06/08/2018
Kobe
Plates
Boiler & Pressure Vessel
Ferritic Low Temperature
Hot Rolled Coil
150
50
60
80
90
100
40
90
100
90
50
13
13
Kakogawa Works
1 Kanazawa-cho
Kakogawa-city
Hyogo-pref.
Tel: +81 794 36 1151 Fax: +81 794 36 2079
Email: shiraishi.toshiharu@steel.kobelco.co.jp
All grades with specified through thickness properties.
Certificate No. MD00/0863/0010/1 Expiry date: 14/10/2018
Materials Quality Scheme Approved - Approval No. MQS 009
KOBE STEEL, LTD.
Kobe
Steelmaking
Semi-Finished
Bars
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
48
8
600
250
250
250
160
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Kobe Works
2 Nadahama-Higashimachi
Nada-ku
Kobe
Tel +81 78 882 8057 Fax +81 78 882 8211
email: abe.masahiroi@kobelco.com web: www.kobelco.co.jp
Certificate No. MD00/0864/0008/1 Expiry date: 07/08/2017
The maximum dimensions of bars rolled from continuously cast blooms are limited to 120 mm for alloy steels and 160 mm for all other grades.
KYOEI STEEL LTD.
Nagasaki
Steelmaking
Sections
Bars
E.A.F. / Con Cast
Normal Strength
Normal Strength
As below
A
A
16
53
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese
16
Yamaguchi Division
Oaza Onoda 6289-18
Sanyo-Onoda City
Yamaguchi Prefecture
756-0817
Tel: +81 836 83 6172 Fax: +81 836 83 0839
email ssetoguchi@kyoeisteel.co.jp web www.kyoeisteel.co.jp
Certificate No. MD00/1892/0007/1 Expiry date: 19/03/2019
MITSUBISHI STEEL MFG. CO., LTD.
Yokohama
Hirota Works
405, Aza Rokucho
Hirota, Kawahigashi-machi
Aizuwakamatsu-city
Fukushima Pref. 969-3471
tel: +81 (0) 242 75 3111 Fax: +81 (0) 242 75 2619
email suzuki.toshihiro@mitubishisteel.co.jp web: www.mitsubishisteel.co.jp
Certificate Number: MD00/1802/0003/1 Expiry: 28/02/2018
Ingots nominal 2050mm diameter x nominal 1250mm length to the above maximum weight are approved for further processing forgings.
MITSUBISHI STEEL MURORAN INC.
Yokohama
Semi-Finished
Ingots (tonnes)
Blooms/Billets
Structural
Machinery
As below
As below
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
Bars
Normal Strength
A
38
Plates
Austenitic Stainless
55
Duplex Stainless
Clad
304L, 304LN, 316L, 316LN, 317L, 317LN, 321,
347, 304*, 316*
UNS S31803
A/304L, D/304L, D/316L
E.A.F. / Con Cast
Slabs
Austenitic Stainless
Austenitic Stainless
austenitic stainless, duplex stainless
austenitic stainless, duplex stainless
304L, 316L
304L, 316L
Bars
20
515
270
210
Muroran Works
12, Nakamachi
Muroran shi
Hokkaido
050-0087
Tel: +81 (0)143 41 2831 Fax: +81 (0)143 41 2869
Email: yano.masashiro@mitsubishisteel.co.jp
Web: www.mitsubishisteel.co.jp
Certificate No. MD00/1893/0008/1 Expiry date: 07/04/2019
NIHON STEEL CO., LTD.
Kobe
11, Rinkai-cho
Kishiwada City
Osaka
tel: +81 724 23 5151 Fax: +81 724 39 8357
Email mailto:t.naka@nihon-steel.co.jp
Web xxxxxxx
Certificate No. MD00/2299/0006/1 Expiry date: 10/03/2017
NIPPON STEEL & SUMIKIN
Nagasaki
40
40
STAINLESS STEEL CORPORATION
Yawata Works
2108-1, Oaza Maeda Aza Hato
Yawata Higashi-ku
Kitakyshi City, Fukuoka Pref.
* Grades 304 and 316 may be accepted for approved applications.
Tel; +81 93 672 2290 Fax: +81 93 672 2251
Email: mailto:yamamoto.yoshiteru@nssc.nssmc.com
web: http://nssc.nssmc.com
Certificate No. MD00/1105/0010/1 Expiry date: 22/05/2018
NIPPON STEEL & SUMIKIN
Nagasaki
Steelmaking
Semi-Finished
Plates
Hot Rolled Coil
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
49
235
8
8
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Steelmaking
B.O.S. / Con Cast
As below
Semi-Finished
Slabs
As below
Max Thickness/Diameter (mm)
STAINLESS STEEL CORPORATION
Production Division, Hikari Works
3434 Shimata
Hikari City
Yamaguchi 743-8550
Tel +81 833 71 5184 Fax +81 833 71 5215
Email: morimoto.masaya@ns-sc.co.jp
Web: http://www.ns-sc.co.jp
Certificate No. MD00/3196/0004/1 Expiry date: 23/10/2017
NIPPON STEEL & SUMITOMO METAL
CORPORATION
Yokohama
Plates
carbon, carbon-manganese
300
Blooms/Billets
carbon, carbon-manganese, alloy
165
Normal Strength
A, B, D, E
100
Higher Strength
AH42, DH42, EH42, FH42
50
AH46, AH50, DH46, DH50, EH46, EH50, FH46,
FH50, FH69*, EH69*
AH40, DH40, EH40, FH40
70
Boiler & Pressure Vessel
Ferritic Low Temperature
Sections
Plates from coils
Hot Coiled Strip
80
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36, FH27S, FH32, FH36
360AR, 410AR
100
360FG, 410FG, 460FG, 490FG, 510FG
100
40
LHAH42, LTAH46, LTAH50, LTDH42, LTDH46,
LTDH50, LTEH42, LTEH46, LTEH50, LTFH42,
LTFH46, LTFH50
LTAH40, LTDH40, LTEH40, LTFH40
50
100
Tapered
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
A,B,D,E, HTS up to EH40
Differential Thickness
A,B,D,E, HTS up to EH40
50
Normal Strength
A, B, D
24
Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36
19
Normal Strength
A, B
12
Boiler and Pressure Vessel
360, 410
12
Normal Strength
A, B
25
Boiler & Pressure Vessel
360, 410
25
80
50
Kimitsu Works
1 Kimitsu
Kimitsu-shi
Chiba-ken
299-1141
Materials Quality Scheme approved - MQS001
Semi Finished products include Carbon and Carbon-manganese as Fine Grain Al and Fine Grain Al+Nb slabs to 1500mm wide, to 10,400mm long (maximum
weight 24T) and Carbon, Carbon-manganese and Alloy as Killed, Fine Grain Al and Fine Grain Al+Nb Blooms to 165mm diameter, to 11m long (amaximum
weight 1.85T), all for further processing.
High strength fine grained Ti+Nb steel plates produced in the TM + Acc and TM + Acc + Temper conditions up to 70mm thickness are approved with Mn and
Al contents to be outside that given in Lloyd's Register Materials Rules. Letter 'S' is used after identification number of non-standard composition materials.
Materials Quality Scheme covers Steelmaking and rolled plates only with exception of EH/FH69 grade. Strip, plate cut from coil, sections and EH/FH69 grade
approved under Materials Survey Scheme (direct survey).
* Project specific approval only. Letter ref MAT/1100/GY/10641564 refers.
Tel: +81 (0)439 50 2194 Fax: +81 (0)439 55 8727 Email: mailto:kurogi.n9q.yasuo@jp.nssmc.com
Web: http://www.nssmc.com/works/kimitsu/
Certificate No. MD00/1100/0013/1 Expiry date: 17/06/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
50
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
NIPPON STEEL & SUMITOMO METAL
CORPORATION
Yokohama
Steelmaking
B.O.S./E.A.F./Ingot/Con Cast
As Below
Max Thickness/Diameter (mm)
Semi-Finished
Billets
carbon, carbon-manganese, alloy
190
Bars
Normal Strength
A, B
200
Higher Strength
AH32, AH36, DH32
200
Chain Cable Stock
U1, U2, U3, R3, R3S, R4
136
API-2F
152
Muroran Works
12, Naka-machi
Muroran City
Hokkaido
050-8550
Tel: +81 (0)143 47 2337 Fax: +81 (0)143 47 2783 Email: amata.g47.takafumi@jp.nssmc.com Web: http://www.nssmc.con/works/muroran
The approval for bars intended for chain cable stock are for material rolled from continuous casting billets only.
Bars for mooring grade chain cable stock in grades R3, R3S and R4 are restricted to Hamanaka Chain Mfg. Co. Ltd. Himeji plant only.
Bars in Grade U3 in the above supply condition may be accepted up to 200mm diameter for the further processing for the production of forged chain cable
fittings.
Approval for billets, maximum 190mm x 190mm x 8000mm maximum weight 2.3 Tonnes, as semi finished products are for further processing for forgings.
Certificate Number: MD00/1101/0012/1 Expiry date: 01/07/2017
NIPPON STEEL & SUMITOMO METAL
CORPORATION
Kobe
Steelmaking
B.O.S./Ingot/Con Cast
As below
Plates
Normal Strength
A, B, D, E
Higher Strength
FH27S
40
AH40, DH40
50
DH42, DH46, EH40, EH42, FH32, FH36, FH40,
FH42
EH46, EH46S, FH46, FH46S
70
110
FH69*
120
DH50, DH55, DH62, DH69
200
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
210
360, 410
115
360FG, 410FG, 460FG, 490FG, 510FG
120
Boiler & Pressure Vessel
130
40
Ferritic Low Temperature
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
40
Steelmaking
B.O.S. / Con Cast
As below
Plates
Normal Strength
A, B, D, E
Higher Strength
DH42, EH42, FH42
50
EH40S*
60
EH47-W430, EH47-W140
70
AH40, DH40, EH40, FH27S, FH32, FH36, FH40
80
EH47
90
Nagoya Works
3, 5 Chome
Tokai-machi
Tokai-city
Aichi Pref. 476-8686
Tel +81 52 603 7236 Fax +81 52 603 7229
Email: okushima_6d7.motohiro@nscmc.com
All grades and thicknesses with specified through thickness properties (Z35)
Certificate No. MD00/1102/0012/1 Expiry date: 16/07/2016
NIPPON STEEL & SUMITOMO METAL
CORPORATION
Nagasaki
Boiler & Pressure Vessel
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
51
100
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36, EH40*, EH47S, EH40S**
360AR, 410AR, 460AR
100
40
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Nagasaki
Plates
Boiler & Pressure Vessel
360, 410, 460, 490
Max Thickness/Diameter (mm)
Japan
NIPPON STEEL & SUMITOMO METAL
CORPORATION
90
360FG, 410FG, 460FG, 490FG, 510FG
Ferritic Low Temperature
Hot Rolled Coil
100
Tapered
LTAH27S, LTAH32, LTAH36, LTAH40,
LTDH27S, LTDH32, LTDH36, LTDH40,
LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,
LTFH32, LTFH36, LTFH40
AH40, DH40, EH40
80
50
Differential Thickness
A, B, D, E, A,B,D,E, AH27S, AH32, AH36,
DH27S, DH32, DH36, EH27S, EH32, EH36
A,B,D
50
Normal Strength
A,B, A,B,D,E, AH27S, AH32, AH36, DH27S,
DH32, DH36, EH27S, EH32, EH36
A
Higher Strength
AH27S, AH32, AH36
12
Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG
12
30
35
12
Oita Works
1, Oaza Nishinotsu
Oita-City
Oita-Prefecture
Tel +81 97 553 2122
Fax +81 97 553 2379
Email: saito.bc3.shuntaroh@jp.nssmc.com
Web http://www.nssmc.com/works/oita/index.html/
All plates with specified through thickness properties.
* Plates in LLF27 and LLF33 up to a maximum thickness of 40 mm can be accepted for approved applications.
* Plates in EH40S are for approved applications only and may have a Nickel content up to 1.5% with a carbon equivalent of 0.4%. The Approved thickness
range of EH40S is 30mm to 60mm.
* Plates in the H47 grades to be produced to the agreed chemistry ranges and agreed max CEVs.
** EH40S is approved with demonstrated brittle crack arrest properties.
* EH40 is approved with demonstrated brittle crack arrest properties.
Materials Quality Scheme Approved - Approval No. MQS010
Certificate No. MD00/1103/0017/1 Expiry date: 29/03/2019
NIPPON STEEL & SUMITOMO METAL
CORPORATION
Yokohama
Steelmaking
Plates
B.O.S. / Con Cast
carbon, carbon-manganese, alloy
A.O.D./Con Cast
austenitic stainless
Normal Strength
A, B, D, E
Higher Strength
AH32S
30
FH27S
32
FH32, FH36
43
AH42, AH46, AH50, AH55, AH62, DH42, DH46,
DH50, DH55, DH62
AH36S, AH40S, DH36S, DH40S, EH36S, EH40S
47
AH36, AH40, DH36, DH40, EH27S, EH32, EH36,
EH40
AH27S, AH32, DH27S, DH32
105
Boiler & Pressure Vessel
150
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
52
150
360AR, 410AR, 460AR
40
510FG
55
360, 410, 460, 490
63
360FG, 410FG, 460FG, 490FG
Ferritic Low Temperature
50
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
100
45
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Yokohama
Plates
Ferritic Low Temperature
9Ni
50
Clad
EH36/304L, EH36/316L
38
Differential Thickness
EH27S, EH32, EH36
32
35
Normal Strength
A,B,D, AH27S, AH32, AH36, DH27S, DH32,
DH36
A, B, D, E
Higher Strength
AH40, DH40, EH27S, EH32, EH36
18
DH27S, DH32, DH36
20
AH27S, AH32, AH36
35
Normal Strength
A, B, D
19
Boiler & Pressure Vessel
360FG, 360, 410FG, 410
19
Japan
NIPPON STEEL & SUMITOMO METAL
CORPORATION
Sections
Hot Coiled Strip
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
53
35
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Kashima Works
3 Hikari
Kashima City
Ibaraki Pref.
314-0014
Tel +81 (0)299 84 2575
Fax +81 299 84 2945
E-mail: hasegawa.md3.kazuhiko@jp.nssmc.com
Website: www.sumitomometals.co.jp
All plates with specified through thickness properties.
Materials Quality Scheme Approved - Approval No. MQS 002
9Ni grade supplied in QLT condition: prior to tempering treatment,plates may be subjected to an intermediate heat treatment.
Welding of 9Ni is restricted to a maximum heat input of 3KJ/mm.
EN 10028-4 X8Ni9, X7Ni9 grades which show equivalence to Lloyd's Register 9Ni can be accepted for approved applications.
NSSMC’s NSGP-2 Corrosion Resistant Steel Grades are approved as below:
Plates AH32 RCW, DH32 RCW, AH36 RCW, DH36 RCW in the TM Condition fine grain treated with Al+Ti to a
thickness of 20mm with through thickness properties of Z35
Plates AH32 RCW, DH32 RCW, AH36 RCW, DH36 RCW in the TM+Acc Condition fine grain treated with Al+Ti to a
thickness of 30mm with through thickness properties of Z35
SMI's Fatigue Crack Arrester (FCA) grades by the DAC process with parent plate fatigue crack growth rates guaranteed by the manufacturer and tested in
accordance with ASTM E647 may be accepted for approved applications. Properties are to be as agreed with the Society. This acceptance does not imply
concessions on either design or survey requirements.
SMI's High Welding Heat Input Steel, may be accepted for approved applications, in all higher tensile strength grades up to EH40, in the TM + ACC condition
up to 105 mm thickness, when used in accordance with SMI's guidelines for welding or line heating. This acceptance does not imply concessions on either
design or survey requirements.
SMICORE, may be accepted for approved applications, in all higher tensile strength grades up to EH36, in the TM condition up to 20mm thickness and the TM
+ ACC condition up to 30 mm thickness. The steel is to have a guaranteed CRL of 0.5 or less and to be of approved composition. This acceptance does not
imply concessions on either design or survey requirements.
(Note CRL = Corrosion Ratio by Long term test)
NSSMC’s Steel Grades bearing Sn are approved as below:
Plates AH32, AH36, DH32 and DH36 in the TM condition fine grain treated with Al+Ti to a thickness of 25 mm with through-thickness properties of Z35
Plates AH32, AH36, DH32 and DH36 in the TM +Acc condition fine grain treated with Al+Ti to a thickness of 30 mm with through-thickness properties of Z35
Certificate No. MD00/1454/0023/1 Expiry date: 07/07/2019
NIPPON STEEL & SUMITOMO METAL
CORPORATION
Kobe
Bars
Normal Strength
A
240
Pipe & Tube Unit
Amagasaki Works
1, Nishino-cho
Higashi-Mukojima
Amagasaki, 660-0856
Tel: +81 (0)6 6411 7616 Fax: +81 (0)6 6411 7612 Email: mailto:furubaya-hdy@sumitomometals.co.jp
Certificate No. MD00/1458/0008/1 Expiry date: 13/11/2016
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
54
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
NIPPON STEEL & SUMITOMO METAL
CORPORATION
Kobe
Steelmaking
B.O.S. / Con Cast
carbon, carbon-manganese, alloy
A.O.D./Con Cast
austenitic stainless
Rolled Bars
Carbon, Carbon manganese
Semi-Finished
Max Thickness/Diameter (mm)
400
Wakayama Works (Wakayama & Kainan)
1850 Minato
Wakayama-city
640-8555
Tel: +81 (0) 73451 1133 Fax: +81 734 51 1103
E-Mail: matsushita.6df.satoshi@jp.nssmc.com
Website: www.sumitomometals.co.jp
Approved for Semi-fhinished as rolled Round Billet with the diameter from 83mm to 400mm; As cast Round Billet with the diameter from 191mm to 453mm;
As rolled Blooms 140mm x140mm to 550mm x 550mm; As cast Blooms 410mm x 530mm, 600mm x 670mm; As cast Slabs 700-1950mm x 227mm/250mm.
Certificate No. MD00/1748/0013/1 Expiry date: 24/06/2019
NIPPON STEEL & SUMITOMO METAL
CORPORATION
Kobe
Sections
Normal Strength
A, B, D, E
50
Higher Strength
AH32, AH36, DH32, DH36, EH32, EH36
50
Steelmaking
Semi-Finished
Plates
E.A.F. / Con Cast
Slabs
Austenitic Stainless
Hot Rolled Coil
Fe-Ni alloys
Austenitic Stainless
Fe-Ni alloys
As below
As below, austenitic stainless
321, 347
304L, 316L
Fe-36Ni*
304L, 316L, 321, 347
Fe-36Ni*
200
10
53
8
8
3
Steelmaking
Hot Rolled Coil
E.A.F./V.O.D./Con Cast
Austenitic Stainless
austenitic stainless
304L, 316L, 304*, 316*
200
9
Steelmaking
Hot Rolled Coil
E.A.F. / Con Cast
Austenitic Stainless
As below
304L, 316L, 321, 347
Wakayama Works [Sakai Area]
1, Chikko Yawata-cho Sakai-Ku
Sakai city
Osaka
Tel: +81 722 33 1179 Fax: +81 722 33 1185
Certificate No. MD00/4141/0005/1 Expiry: 08/07/2018
NIPPON YAKIN KOGYO Co., Ltd.
Yokohama
KAWASAKI PLANT
4-2, Kojima-cho
Kawasaki-ku
Kawasaki-shi
Kanagawa - ken 210-8558
Tel: +81 44 271 3045 Fax: +81 44 271 3044
email mailto:kensuke.miura@nyk.co.jp web www.nyk.co.jp
Certificate No. MD00/1109/0008/1 Expiry date: 31/05/2018
* accepted for approved applications
NISSHIN STEEL CO. LTD
Nagasaki
SHUNAN WORKS
4976, Nomuraminami-machi,
Shunan City,
Yamaguchi Pref, 746 8666
Tel: +81-3-3216-6327 Fax: +81-3-3214-6325
Website: www.nisshin.steel.co.jp
Cert No: MD00/4481/0001/1
NISSHIN STEEL CO., LTD.
Expiry Date: 13/05/2018
Kobe
8
Kinuura Works
1, Hama-cho
Hekinan-shi
Aichi- ken
447-8610
Tel: +81 566 48 7218 Fax: +81 566 48 1596
Email: mailto: tomita.a768@nisshin-steel.co.jp
Web: http://www.nisshin-steel.co.jp/en
Certificate No. MD00/2338/0008/1 Expiry date: 21/05/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
55
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
OJI STEEL CO., LTD.
Yokohama
Steelmaking
Semi-Finished
Bars
E.A.F. / Con Cast
Billets
Normal Strength
Higher Strength
As below
carbon, carbon-manganese
A
AH32, AH36
Max Thickness/Diameter (mm)
170
25
25
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Blooms/Billets
Sections
Normal Strength
Higher Strength
carbon, carbon-manganese
AH32, AH36
A
A
AH32, AH36
165
190
15
12
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Blooms/Billets
Sections
Normal Strength
Higher Strength
Steelmaking
E.A.F. / Con Cast
E.A.F. / Ingot
Ingots (tonnes)
Blooms
Gunma Works
120, Nittasorimachi-cho
Ota-city
Gunma Pref.
370-0313
Tel: +81 276 56 2119 Fax: +81 276 56 3136
Email: mailto:t-kudoh@oji-steel.co.jp
Web: www. oji-steel.co.jp
Certificate No. MD00/1141/0007/1 Expiry date: 14/10/2017
OSAKA STEEL CO., LTD.
Kobe
Sakai Works
1 Chikko Yawata-cho
Sakai
Osaka
Tel +81 722 33 3901
Fax +81 722 33 3976
Certificate No. MD00/0821/0010/1 Expiry date: 20/05/2019
OSAKA STEEL CO., LTD.
Kobe
As below
carbon, carbon-manganese, Normal Strength,
Higher Strength
A, B, D
AH32, AH36
165
15
12
Osaka - Okajima Works
9-3 Minami Okajima 1 Chome
Taisho-ku
Osaka 551-0021
Tel: +81 06 6552 1447 Fax: +81 06 6552 3184
Email: ko-kisimoto@osaka-seitetsu.co.jp
Web :www.osaka-seitetu.co.jp
Certificate No. MD00/1157/0007/1 Expiry date: 20/05/2019
SANYO SPECIAL STEEL CO., LTD.,
Kobe
Semi-Finished
Bars
Normal Strength
Machinery
Chain Cable Stock
alloy, austenitic stainless
As below
carbon, carbon-manganese, austenitic stainless
carbon, carbon-manganese, alloy, austenitic
stainless
A
alloy
U1, U2, U3
15
380
220
220
136
3007 Nakashima
Shikama-ku
Himeji-shi
672-8677
Tel: +81 (0)792 35 6029 Fax: +81 (0)792 35 6027
email: taota@himeji.sanyo-steel.co.jp web: www.sanyo-steel.co.jp
Heat treatment sub contracted to Toyo Metal Treating Corporation, Takasago Plant No. 2, Takasago, Hyogo Pref., Japan.
Certificate No. MD00/1307/0012/1 Expiry date: 31/10/2016
SHINKANSAI STEEL CORPORATION
Kobe
Steelmaking
Sections
E.A.F. / Con Cast
Normal Strength
Higher Strength
As below
A, B, D, E
AH32, AH36, DH32, DH36
38
38
Sakai Works
5, Shiohama-cho
Sakai-ku, Sakai
Osaka 590-0981
Tel: +81 (0)72 228 5121 Fax: +81 (0)72 228 7119 Email: mailto:h-ue@shinkansai-steel.co.jp
Certificate No. MD00/0823/0009/1 Expiry date: 14/11/2017
SHINKANSAI STEEL CORPORATION
Kobe
Steelmaking
Sections
Web: http://www.shinkansai-steel.co.jp
E.A.F. / Con Cast
Normal Strength
Higher Strength
Chain Cable Stock
Bars
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
56
As below
A, B, D
AH32, AH36, DH32, DH36
U1, U2, U3
32
32
80
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
Hoshida Works
4-26-1, Hoshida Kita
Katano-shi
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Steelmaking
Plates
E.A.F. / Ingot
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
304L, 316L
AH32/304L, AH32/316L, AH32/316LN,
AH32/317L
AH32/S31803
A/304L, B/304L, D/304L, E/304L, A/316L,
B/316L, D/316L, E/316L
Osaka
Tel: +81 (0)72 891 0624 Fax: +81 (0)72 893 1319
Email: h-ito@shinkansai-steel.co.jp
Web: http://www.shikansai-steel.co.jp
Certificate No. MD00/1244/0008/1 Expiry date: 05/10/2018
THE JAPAN STEEL WORKS, LTD.
Yokohama
Austenitic Stainless
Clad
50
50
40
50
65
19
30
100
Muroran Plant
4, Chatsu-machi
Muroran
Hokkaido
051-8505
Tel +81 (0)143 22 0539 Fax +81 (0)143 22 5736
email: https://www.jsw.co.jp/en/contact/ web: www.jsw.co.jp
Certificate No. MD00/1507/0008/1 Expiry date: 09/11/2018
TOKAI SPECIAL STEEL CO., LTD.
Kobe
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Blooms
Billets
carbon, carbon-manganese
carbon, carbon-manganese
carbon, carbon-manganese
Steelmaking
Plates
Sections
E.A.F. / Con Cast
Normal Strength
Boiler & Pressure Vessel
Normal Strength
As below
A, B, D
360AR, 410AR
A
Steelmaking
Sections
E.A.F. / Con Cast
Normal Strength
370
155
3, 5-Chome
Tokai-Machi
Tokai-shi
Aichi-ken
Tel +81 52 603 7236 Fax +81 52 603 7229
email: komparu.58q.tomoaki@nssmc.co.jp
Certificate No. MD00/1542/0006/1 Expiry date: 02/02/2017
TOKYO STEEL MANUFACTURING CO., LTD.
Nagasaki
32
32
24
Kyushu Plant
3-5-1, Minami-Futajima
Wakamatsu-ku
Kitakyushu City
Fukuoka 808-0109
Tel: +81 93 701 2631 Fax: 81 93 791 2639
Email: mailto: itou_g@tokyosteel.co.jp
Web http://www.tokyosteel.co.jp
Certificate No. MD00/1550/0009/1 Expiry date: 23/06/2017
TOPY INDUSTRIES, LTD.
Kobe
Bars
Normal Strength
Higher Strength
As below
E
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36, FH27S, FH32, FH36
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
Steelmaking
E.A.F. / Ingot
carbon, carbon-manganese, alloy
Higher Strength
Ferritic Low Temperature
20
35
20
20
50
50
Toyohashi Works
1, Akemi-cho
Toyohashi-shi
Aichi-ken
Tel +81 532 25 1111 Fax +81 532 25 7401
Email: mailto: m-takeuchi@topy.co.jp
web: http://www.topy.co.jp
Certificate No. MD00/1555/0008/1 Expiry date: 16/06/2017
TSUNEISHI IRON WORKS Co., Ltd
Nagasaki
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
57
60
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
Wakamatsu Steel Factory
43-1 Koyo-machi
Wakamatsu-ward
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
E.A.F. / Con Cast
Normal Strength
Higher Strength
As below
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
Kitakyushu-city, 808-0002
Tel: +81 (0)93 752 0770 Fax:+86 (0)93 752 0777
Email to: hideo.fukusada@tsuneishi.com Web: http://www.tsuneishi-iw.jp
Certificate No.: MD00/4392/0001/2
YAMATO STEEL CO., LTD.
Expiry Date: 12/10/2017
Kobe
Steelmaking
Sections
25
25
380, Kibi, Ohtsu-ku
Himeji City
Hyogo-pref.
Tel: +81 (0)79 273 0716 Fax: +81 (0)79 272 0914 Email mailto: knakaue@yamatosteel.co.jp
Certificate No. MD00/1687/00010/1 Expiry date: 10/06/2017
Web:http://www.yamatokogyo.co.jp
Korea
BUSAN STEEL CO., LTD.
Busan Port
Plates from coils
Austenitic Stainless Steel
304L, 304LN, 316L, 316LN, 317L, 317LN, 321,
347
Plates
Austenitic Stainless
Duplex Stainless
304L, 304LN, 316L, 316LN
UNS S31803, UNS 32900*, UNS 32205*
8
29, Songjeuong-gil (Songjung-Dong),
Gangseo-Gu
Busan
Tel: +82 51 831 3700, Fax No. +82 51 831 3701
Email: gjj072@nate.com
Website: www.busansteel.co.kr
Certificate No. MD00/4028/0002/1 Expiry date: 23/06/2018
DK CORPORATION
Ulsan
80
50
66, Gohyeon-Gil, 98 Beon-gil,
Cheongha-ri, Buk-gu, Pohang-si,
Kyungsangbuk-do
Tel: +82 (0)54 245 3062 Fax: +82 (0)54 245 3065 Email:mailto:hugging@dkcsteel.com Web:http://www.dkcsteel.com
*accepted for approved applications
The scope of approval is for the heat treatment and final testing of plates only from rolled plates supplied from approved works.
Certificate Number: MD00/2230/0007/1 Expiry: 28/05/2019
DONG IL STEEL CO. LTD
Busan Port
Sections
Normal Strength
Higher Strength
A
AH32, AH36
12
12
Steelmaking
Semi-Finished
Plates
E.A.F. / Con Cast
Blooms/Billets
Normal Strength
carbon-manganese
carbon-manganese
D, E
A, B
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36, FH27S, FH32, FH36
460FG, 490FG, 510FG
360AR, 410AR
360FG, 410FG
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
D
A, B
AH27S, DH32
AH32, DH27S
SASANG WORKS
50, Daedong-ro,
193, Beon-gil, Sasang-gu,
Busan
Tel No. + 82-51-323-1177
Fax No: + 820 - 325 6378
Website: www.dongilsteel.com
Certificate No:
MD00/4517/0001/1
DONGKUK STEEL MILL Co. Ltd.
Expiry Date: 14/10/2015
Ulsan
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
Sections
Normal Strength
Higher Strength
480
50
83
50
35
40
50
50
25
32
25
32
Pohang Works
195, Cheolgangsandan-ro,
Daesong-myeon, Nam-gu,
Pohang-si, Gyeongsangbuk-do
Tel: +82 054 721 3261 Fax: +82 02 317 9055
email: jongho.chun@dongkuk.com web: www.dongkuk.com
Certificate No. MD00/0414/0014/1 Expiry date: 13/05/2019
Billets to 150 x 150mm, Blooms to 200 x 250 & 250 x 300, Beam Blanks to 400 x 480 x 120mm.
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
58
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
DONGKUK STEEL MILL Co. Ltd.
Seoul
Plates
Normal Strength
E
A, B, D
FH32, FH36
AH32, AH36, AH40, DH32, DH36, DH40, EH32,
EH36, EH40
460AR
360AR, 410AR
490FG
460FG, 510FG
360FG, 410FG
LTFH32, LTFH36
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
Max Thickness/Diameter (mm)
83
100
50
83
35
40
50
70
100
50
Dangjin Works
25, Godaegongdan 1-gil,
Song-ak-eup, Dangjin-si,
Chungcheongnam-do
Tel: +82 (0) 41 351 4679 Fax: +82 (0) 41 317 9083
Email: dongjin.kim@dongkuk.com Web: http://www.dongkuksteel.co.kr
Certifcate Number: MD00/3773/0010/1 Expiry: 10/04/2019
Plates in the Normalised supply condition Fine Grain Al+V are only accepted in the thickness range >30mm to 70mm.
Approval includes Z grade plates with specified through thickness properties when tested in accordance with LR Rules requirements.
DONGYANG S.TEC. CO., LTD
Ulsan
Plates from coils
Normal Strength
A
20
Steelmaking
E.A.F. / Ingot
As below
Semi-Finished
Ingots (tonnes)
carbon, carbon-manganese, alloy, austenitic
stainless
Sections
Normal Strength
Ferritic Low Temperature
B, D, E
A
DH32, DH36, EH32, EH36, FH32, FH36
AH27S, AH32, AH36
LTAH32, LTDH32, LTEH32, LTFH32, LTFH36
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Blooms
Billets
Normal Strength
Higher Strength
As below
carbon, carbon-manganese, alloy
carbon, carbon-manganese
carbon, carbon-manganese
A, B
AH27S, AH32, AH36
125
270
200
32
32
As below
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
B, D, E
A
AH27S, AH40, DH27S, DH40, EH27S, EH32,
120
18
37
18
#619-12, Munduk-Ri,
Ocheon-Eup Nam-Gu,
Pohang-city, Kyeongbuk,
Tel: +82 54 292 6181 Fax: +82 54 291 6548
Email: kyb4621@hanmail.net
Website www.dystec.co.kr
Certifcate Number: MD00/3840/0003/1 Expiry date: 26/09/2016
DOOSAN HEAVY INDUSTRIES & CONSTRUCTION
CO., LTD.
Changwon
500
Changwon Plant
22, Doosanvolvo-ro,
Seongsan-gu,
Changwon,
Kyungnam,
Tel +82 55 278 4746 Fax no. +82 55 278 8506
youngsu.bae@doosan.com web www.doosanheavy.com
Certificate No. MD00/0883/0002/1 Expiry date 08/03/2019
FINE BESTEEL CO LTD
Changwon
Higher Strength
18
30
18
30
18
25-1 Ha-Ri, Changnyeong-Up,
Changnyeong-Gun,
Gyeongnam,
Tel: +82 (0)55 259 2076 / 2064 Fax: +82 (0)55 259 2070
Email: sungjh@finebesteel.com
Web www.fine-besteel.com
Certificate No. MD00/3659/0006/1 Expiry date: 09/09/2018
HYUNDAI STEEL COMPANY
Seoul
Steelmaking
Semi-Finished
Sections
Inchon Plant
63, Jungbong-Daero
Dong-Gu
Inchon
Tel: +82 32 760 2753 Fax: +82 32 760 2866 Email: arom@hyundai-steel.com Web: http://www.hyundai-steel.com
Sections flat bars up to 400 mm width.
Certificate No. MD00/0754/0010/1 Expiry date: 02/01/2017
HYUNDAI STEEL COMPANY
Ulsan
Steelmaking
Semi-Finished
Sections
E.A.F. / Con Cast
Blooms/Billets
Bars
Normal Strength
Higher Strength
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
59
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Sections
Higher Strength
EH36, EH40, FH27S, FH32, FH36, FH40
AH32, AH36, DH32, DH36
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36, LTFH40
carbon, carbon-manganese, alloy
R3S, R4
U1, U2, U3, R3
Korea
Ferritic Low Temperature
Bars
Machinery
Chain Cable Stock
Steelmaking
Sections
E.A.F. / Con Cast
Normal Strength
Higher Strength
18
37
18
120
110
150
Pohang Plant No. 1
6363, Donghaean-ro
Nam-Gu, Pohang-si
Gyeongsangbuk-do
Tel: +82 54 271 1479 Fax: +82 54 271 1512
Email: mailto:2007372@hyundai-steel.com
Web: http://www.hyundai-steel.com
Certificate No. MD00/0819/0017/1 Expiry date: 05/06/2019
HYUNDAI STEEL COMPANY
Ulsan
Ferritic Low Temperature
carbon-manganese
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36, FH27S, FH32, FH36
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
16
16
16
Pohang Plant No. 2
36, Cheolgang-ro 314 beon-gil,
Nam-Gu, Pohang-si,
Tel No. +82 54 271 1479 Fax No. +82 54 271 1512
Email mailto:2007372@hyundai-steel.com
Web: www.hyundai-steel.com
Certificate No. MD00/3084/0007/1 Expiry date: 05/06/2019
HYUNDAI STEEL COMPANY
Seoul
Steelmaking
Semi-Finished
Hot Rolled Coil
Plates from coils
B.O.S./E.A.F./Con Cast
Slabs
Normal Strength
Higher Strength
Normal Strength
Higher Strength
As Below
Normal strength, Higher Strength
A, B
AH32, AH36
A, B
AH32, AH36
300
22
22
22
22
HR Coil Plant
1480, Bukbusaneop-ro
Songak-eup
Dangjin-si
Chungncheongnam-do
Tel: +82 41 680 1691 Fax +82 41 680 1699 Email; jwmking@hyundai-steel.com Web: http://www.hyundai-steel.com
Slabs with nominal 2200mm width x nominal 4400mm length
Certificate No. MD00/3446/0004/1 Expiry date: 23/03/2017
HYUNDAI STEEL COMPANY
Seoul
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
60
A, B, D, E
AH42, AH46, AH50, DH42, DH46, DH50, EH42,
EH46, EH50, FH40, FH42, FH46, FH50
FH27S, FH32, FH36, EH40*
EH47
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40,
EH40S**
360AR, 410AR, 460AR
460FG, 490FG
360FG, 410FG
LTDH27S, LTDH32, LTDH36, LTFH27S,
LTFH32, LTFH36
100
50
80
83
100
40
83
100
40
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Dangjin Works
1480, Bukbusaneop-ro
Songak-Eup
Dangjin-Si
Chungcheongnam-do
Tel: +82 41 680 1690 or 1685 Fax +82 41 680 1699
email; jwmking@hyundai-steel.com web: http://www.hyundai-steel.com
Approval for plates in grades AH27S, AH32, AH36, 360AR, 410AR, and 460AR as rolled fine grain Al+V are restricted to the thickness range 20.0mm to
35.0mm.
Approval for plates in grades AH27S, AH32, AH36, AH40, DH27S, DH32, DH36, DH40, EH27S, EH32, EH36, EH40 for the TM+Acc fine grain Al+Nb+Ti
supply condition are restricted to the thickness range >15.0mm to 83.0mm.
Approval for plates in grades LTDH27S, LTDH32, LTDH36, LTFH27S, LTFH32, LTFH36 for the TM+Acc fine grain Al+Nb+Ti supply condition are restricted to
the thickness range >15.0mm to 40.0mm.
Approval for plates in Normalising Rolled condition are restricted to maximum 3200mm width.
Plates with specified through thickness properties may be accepted with the suffix Z35.
EH40* is approved with demonstrated brittle crack arrest properties.
Approved for corrosion resistant steel plates in grades AH27S RCB and AH32 RCB with Z35 through thickness properties to 40 mm maximum thickness in TM
supply condition with Al+Nb+Ti grain refining treatment.
Certificate Number: MD00/3761/0015/1 Expiry: 22/03/2019
HYUNDAI STEEL COMPANY
Mokpo
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy
100
Bars
Machinery
carbon, carbon-manganese, alloy
123
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy
160
Sections
Normal
Higher
Normal
Higher
A
AH32, AH36, DH32, DH36, EH32, EH36
A
AH32
46, Yulchonsandan 5-ro
Haeryong-myeon
Suncheon City, Jeollanam-do
Zip code: 540856
Tel: +82 61 760 7100 Fax: +82 61 725 7733
email: kimlh@spp.co.kr web: www.sppycenergy.co.kr
Certificate Number: MD00/3866/0004/1 Expiry date: 13/12/2016
JINYANG SPECIALTY STEEL Co., Ltd.
149-9, Damtteul-gil,
Yeongcheon-si,
Gyeongsangbuk-do,
Ulsan
Tel: +82 (0)54 335 3500 Fax: +82 (0)54 335 0355
Email: jysteel@jysteel.co.kr
Web: http:// www.jysteel.co.kr/main
Cert No MD00/3897/0002/1 Expiry date: 22/03/2017
KISCO
Changwon
12, Gongdan-ro
103 beon-gil, Seongsan-gu
Changwon
Gyeongnam
Tel +82 55 260 0746 Fax +82 55 282 4123
Email: ojyworld@kisco.co.kr
Web page http://www.kisco.co.kr
Certificate No. MD00/0884/0005/1 Expiry date: 11/01/2018
KOREA STEEL SHAPES CO., LTD
Busan Port
Bars
Strength
Strength
Strength
Strength
15
15
65
30
Noksan Works
84, Noksansandan 407-Ro,
Gangseo-Gu
Busan,
Tel: +82 51 310 8912 Fax: +82 51 831 3951
email nawoo1@ekosco.com web www.ekosco.com
Certificate No. MD00/3096/0008/1 Expiry date: 21/01/2017
KOREA STEEL SHAPES CO., LTD
Changwon
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Billets
As below
carbon, carbon-manganese, Normal Strength,
Higher Strength
220
Chilseo Works
98, Gongdandong-gil, Chilseo-Myeon,
Haman-Gun,
Gyeongnam,
Tel: +82 55 589 1159 Fax: +82 55 589 1116
email: stmjslee@ekosco.com web: www.ekosco.com
Certificate No. MD00/3097/0002/1 Expiry date: 10/10/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
61
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
KWANG JIN IND CO. LTD.
Busan Port
Bars
Machinery
austenitic stainless
alloy
carbon, carbon-manganese
Max Thickness/Diameter (mm)
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
As below
Normal strength, Higher Strength
A, B, D, E
AH40, DH40, EH40, EH47
FH36, FH40
AH27S, AH32, AH36, AH62, AH69, DH27S,
DH32, DH36, DH62, DH69, EH27S, EH32, EH36,
EH62, EH69, FH27S, FH32
360AR, 410AR, 460FG, 490FG, 510FG
360FG, 410FG
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
360AR, 410AR
85
93
100
160, Hasinjungang-ro,
Saha-gu,
Busan,604-030
Tel No: +82 51 220 9264 Fax No. +82 51 204 9172
Email: mgkang@kjsteel.co.kr
Web Address www.kjsteel.co.kr
Cert No MD00/3758/0003/1 Expiry date 14.03.2019
POSCO Gwangyang Works
Changwon
Boiler & Pressure Vessel
Ferritic Low Temperature
Hot Rolled Coil
Normal Strength
Higher Strength
Boiler & Pressure Vessel
300
100
80
90
100
35
80
40
22
12
12
700 Kumho-dong
Kwangyang-si
Cheonnam 545-711
Tel: +82 61 790 2170 Fax: +82 61 790 2909
Email: ssyang@posco.com Web: http://www.posco.com
Approved for semi-finished products, slabs, nominal 1750mm wide x 6000mm long.
Hot rolled coils in normal strength grades in the supply condition thermomechanical fine grain aluminium are restricted to the thickness ranges >12 to 22mm.
Certificate Number: MD00/3086/0013/1 Expiry: 14/07/2017
POSCO Pohang Works
Ulsan
Steelmaking
Semi-Finished
B.O.S./E.A.F./Con Cast
Slabs
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
Hot Rolled Coil
Austenitic Stainless
Duplex Stainless
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Austenitic Stainless
As Below
carbon, carbon-manganese, alloy, Normal
strength, Higher Strength
A, B, D, E
FH27S, FH32, FH36
AH40, DH40, EH40, EH47
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36, EH40S*
360AR, 410AR
460FG, 490FG, 510FG
360FG, 410FG
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
304L, 304LN, 316L, 316LN
UNS S31803, UNS 32900*, UNS 32205*
E
A, B, D
EH27S, EH32, EH36
AH27S, AH32, AH36, DH27S, DH32, DH36
460FG, 490FG, 510FG
360FG, 410FG
304L, 316L
400
100
83
90
100
40
90
100
50
80
50
12
22
16
22
12
22
8
(Goedong-dong), 6261, Donghaean-ro,
Nam-gu,
Pohang si,
Gyeongsangbuk-do,
Tel: +82 2 3457 3838 Fax: +82 2 3457 6000
email: ayoung89@posco.com web: www.posco.com
Certificate No. MD00/1206/0020/1 Expiry date: 29/04/2019
* EH40S grade is approved with demonstrated crack arrest properties.
Applicable plate grades may be accepted with through thickness properties when manufactured and tested in accordance with the relevant Rules.
Slabs as semi-finished products nominal maximum width 2200mm x nominal maximum length 5000mm to the above maximum thickness are approved for
further processing for rolled and forged products
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
62
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
S & STEEL CO., LTD.
Busan Port
Plates from coils
Normal Strength
Higher Strength
A
AH36
AH27S, AH32
Max Thickness/Diameter (mm)
Steelmaking
Semi-Finished
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Blooms
Billets
Bars
Machinery
Chain Cable Stock
As below
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese
alloy
carbon, carbon-manganese, alloy
R5
R4S, R4S
R4
U1, U2, U3, R3, R3S
18
10
15
1620 Dadae-dong, Saha-gu
Busan
Tel: +82 51 262 7525 Fax: +82 51 924 7902
Email: taxibill@sdstl.co.uk
Web: http://www.sdstl.co.kr
Certificate No. MD00/3523/0006/1 Expiry date: 23/09/2017
SeAH BESTEEL CORPORATION
Mokpo
Bars
155
510
180
350
300
140
146
155
165
Gunsan Plant
1-6, Soryong-Dong
Gunsan City
Jeonlabuk-Do
Tel: +82 63 460 8078 Fax: +82 63 460 8099
email: jiwon.yoo@seah.co.kr web: www.seah.co.kr
Certificate No. MD00/1749/0014/1 Expiry date: 04/04/2018
Approval for Chain Cable Stock Grades R3, R3S, R4, R4S and R5 is restricted to supply to DAI HAN ANCHOR CHAIN MFG CO. LTD and Grades R3, R3S
and R4 to Pu Sung Metal Co., Ltd.
Semi Finished Products - Ingots, Carbon & Carbon-manganese nominal sizes 2100 / 2350mm diameter x 2800mm long, and Alloy nominal sizes 2350 / 2600mm
diameter x 3050mm long, to the above maximum weight approved for further processing for forgings.
Semi Finished Products - Blooms to nominal 390mm width x 5400mm length, to above maximum thickness approved for further processing for Forgings and
Rolled Products.
Semi Finished Products - Billets to nominal 180 width x 11500mm length, to above maximum thickness approved for further processing for Rolled Products.
Alloy grade bars as semi-finished products nominal maximum length 12,000mm to the above maximum diameter are approved for further processing for forged
products.
SeAH CHANGWON INTEGRATED SPECIAL STEEL
Changwon
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
Machinery
As below
duplex stainless
carbon, carbon-manganese, alloy, austenitic
stainless
carbon, carbon-manganese, alloy, duplex
stainless
austenitic stainless
carbon, carbon-manganese, alloy
Bars
Structural
B.O.S. / Con Cast
Normal Strength
Normal Strength
As below
A
A
7
32
304L, 316L
UNS S32750
UNS S31803
13
6
8
17
150
150
170
150
CORPORATION
147,Jeokhyeon-Ro
Seongsan-Gu
Changwon,
Gyeongnam
Tel: +82 (0)55 269 6200 Fax: +82 (0)55 269 6907 Email: junkon@poscoss.com
http://www.poscoss.com
Certificate No. MD00/1294/013/1 Expiry date: 08/08/2017
YK STEEL CORP.
Busan Port
Steelmaking
Sections
Bars
760 Eulsukdo-daero,
Saha-Gu
604-817
Busan
Tel. +82 (0)51 260 2186 Fax +82 (0)51 265 2399 Email: hdkim@yksteel.co.kr Web: http://www.yksteel.co.kr
Certificate No. MD00/0650/0008/1 Expiry date: 25/05/2017
YOUNG GWANG STAINLESS CO., LTD.
Busan Port
Plates from coils
Austenitic Stainless Steel
Duplex Stainless
16, Noksansandan 262-ro
Gangseo-gu
Busan
Tel: +82.51.832.1911 Fax: +82.51.832.1909 Email to: kbj@ygs.co.kr Web: http://www.ygs.c.kr
Certificate No. MD00/4460/0001/1 Expiry date: 31/03/2018
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
63
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
YOUNG GWANG STAINLESS CO., LTD.
Busan Port
Plates from coils
Austenitic Stainless Steel
Duplex Stainless
304L, 316L
UNS S32750
UNS S31803
Max Thickness/Diameter (mm)
13
6
8
406, Noksansaneopjung-ro
Tel: +82.51.832.1911 Fax: +82.51.832.1909 Email to: kbj@ygs.co.kr Web: http://www.ygs.c.kr
Certificate No. MD00/4460/0001/1 Expiry date: 31/03/2018
Luxembourg
ARCELORMITTAL BELVAL ET DIFFERDANGE
Lyon
Steelmaking
Semi-Finished
Sections
E.A.F. / Con Cast
Blooms
Normal Strength
Higher Strength
As below
Normal Strength, Higher Strength
A, B
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
100
26
26
Steelmaking
Semi-Finished
Plates
Sections
E.A.F. / Con Cast
Blooms
Normal Strength
Higher Strength
As below
Higher Strength
A, B
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
135
40
40
BELVAL MILL
TMB Rolling Plant
66 rue de Luxembourg
L4009 Esch sur Alzette
Tel: +352 58 2885 Fax: +352 5835 81
Email: mailto:roberto.klecker@arcelor.com
Web:www.arcelor.com
Certificate #: MD00/0030/0008/1 Expiry date: 04/11/2018
ARCELORMITTAL BELVAL ET DIFFERDANGE
Lyon
Differdange Mill
L 4009 Esch sur Alzette
Tel: +352 58 2028 85 Fax: +352 5835 81
Email: roberto.klecker@arcelormittal.com
Web http://www.arcelormittal.com
Beam Blanks as semi-finished products (referred to as blooms above) nominal 500mm overall width x nominal 1150mm overall length, to the above overall
maximum thickness
Certificate Number: MD00/0032/0008/1 Expiry: 10/03/2019
ARCELORMITTAL RODANGE ET SCHIFFLANGE
Lyon
Sections
Normal Strength
Higher Strength
A, B
AH32, AH36, DH32, DH36
30
30
Fabricated Sections
Normal Strength
Higher Strength
A
AH36, DH36, EH36
35
40
Steelmaking
Plates
E.A.F. / Con Cast
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
360AR, 410AR, 460AR
360, 410, 460, 490, 460FG, 490FG, 510FG
360FG, 410FG
Rodange Mill
2, Rue de L'industrie
L-4801 Rodange
Tel: +352 58 20 28 84 Fax: +352 58 20 35 81
email: :stephane.arnault@areclormittal.com web www.arcelor.com
Certificate No. MD00/2266/0007/1 Expiry date: 16/01/2019
Macedonia
FAKOM A.D.
Beograd
St. Aleksandar Makedonski No.5
POB 439
1000 SKOPJE
Tel No.: +389 317 4023, Fax: +389 317 3564
email: mailto:info@fakom.com.mk
Web http://www.fakom.com.mk
Certificate No. MD00/2856/0008/1 Expiry date: 26/11/2018
MAKSTIL A.D.- SKOPJE
Beograd
100
50
40
50
100
XVI Makedonska brigada 18
P.O. Box 599
1000-Skopje
Tel: +389 2 328 7130
email: igor.bogeski@makstil.com.mk web www.makstil.com
Specified through thickness properties for plates up to 50 mm thickness
Certificate No. MD00/2216/0008/1 Expiry date: 21/05/2019
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
64
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Kuala Lumpur
Plates
Normal Strength
A
E.A.F. / Con Cast
carbon, carbon-manganese
Slabs
carbon, carbon-manganese
Malaysia
JI KANG DIMENSI Sdn. Bhd.
Lot 69-71, Kawasan Perindustrian Gebeng
26100 Kuantan
Pahang Darul Makmur
30
Tel: +609 583 9881 Fax: +609 583 4551
Email: mailto: limf555@163.com
Web: www.jikangdimensi.com
Certificate No. MD00/3022/0005/1 Expiry date: 27/06/2018
Mexico
ARCELORMITTAL LAZARO CARDENAS, S.A. de
C.V.
Metepec/Veracr Steelmaking
uz
Semi-Finished
250
Av Francisco J. Mujica N° 1-B
60950- Lázaro Cárdenas
Michoacan
Steel types carbon and carbon-manganese cover the supply of blooms for processing into normal strength, high strength and ferritic steels for low temperature
service according to the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The final processing mill is responsible for
ordering steel which complies with their approved chemical composition and enables them to achieve the required mechanical properties
Tel: +52 753 533 1917 Fax: +52 753 533 1187
Email: berenice.serrano@arcelormittal.com
Web http://www.arcelormittal..com
Certificate No. MD00/0783/0007/1 Expiry date: 08/01/2017
Montenegro
TOSELIK NIKŠI d.o.o.
Beograd
Steelmaking
EAF/LRF/VD/Ingot
Carbon, Carbon-manganese, Alloy
7
Vuka Karadzica bb,
81400 Niksic
Tel: +382 40 202 222
email: drago.zizic@toscelikniksik.me
Certificate No: MD00/4508/0001/1 Expiry Date: 03/09/2018
Norway
CELSA ARMERINGSSTÅL AS
Oslo
Steelmaking
E.A.F. / Con Cast
carbon, carbon-manganese
Semi-Finished
Billets
A, carbon, carbon-manganese
Normal Strength
Boiler & Pressure Vessel
Normal Strength
A, B, D, E
360AR, 410AR, 360, 410, 360FG, 410FG
A, B, D, E
160
Mo Industripark
PO Box 500
N-8601 Mo i Rana
Tel: +47 7513 6500 Fax: +47 7513 6845
Email: asbjorn.myrvoll@celsanordic.com Web http://www.celsanordic.com
Certificate No. MD00/2103/0006/1 Expiry date: 06/09/2017
Poland
''HUTA POKÓJ'' S.A.
Katowice
Plates
Sections
25
25
25
ul. Niedurnego 79
41-709 Ruda Slaska
Tel +48 32 772 4110 or +48 602 593 445 Fax +48 32 772 4856 Email: dkj@hutapokoj.eu Web: http://www.hutapokoj.eu
Certificate Number: MD00/0723/0008/1 Expiry: 10/12/2015
ALCHEMIA S.A.
Katowice
Steelmaking
E.A.F. / Ingot
Semi-Finished
Ingots (tonnes)
carbon, carbon-manganese, alloy, austenitic
stainless
carbon, carbon-manganese, alloy, austenitic
stainless
14
ODDZIAL STALOWNIA BATORY W CHORZOWIE
ul.Dyrekcyjna 6
41-506 Chorzów
Tel: +48 32 77 22 237 Fax:+48 32 77 22 060
email: :sekretariat.hbt@alchmiasa.pl
web: www.alchemiasa.pl
Certificate No. MD00/0711/0012/1 Expiry date: 06/10/2016
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
65
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
ARCELORMITTAL POLAND S.A.
Katowice
Steelmaking
Semi-Finished
Hot Rolled Coil
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Normal Strength
Higher Strength
Boiler and Pressure Vessel
As below
carbon, carbon-manganese
A, B, D
AH27S, AH32
A, B, D
AH27S, AH32
410 FG, 360 FG, 460 FG
Plates from coils
Max Thickness/Diameter (mm)
220
15
16
15
16
16
ODDZIAL W KRAKOWIE
ul. Ujastek 1
30-969 Kraków
Tel: +48 12 290 1817 Fax: +48 12 290 5591
email: andrzej.zajac@arcelormittal.com web: www.arcelormittal.com/poland
Slabs as semi finished products are approved for further processing for rolled products to the maximum thickness shown above and nominal 1580mm width
and 11000mm length.
Coils and plates are approved to maximum 2100mm width.
Certificate #: MD00/0707/0011/1 Expiry date: 26/01/2017
ARCELORMITTAL POLAND S.A.
Katowice
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Slabs
Blooms/Billets
carbon, carbon-manganese, alloy
carbon, carbon-manganese
carbon, carbon-manganese, Alloy
300
280
Steelmaking
Semi-Finished
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Blooms/Billets
Structural
Machinery
As below
carbon, carbon-manganese,
carbon, carbon-manganese,
carbon, carbon-manganese,
carbon, carbon-manganese,
alloy
alloy
alloy
alloy
25
220
65
65
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy
130
Steelmaking
Semi-Finished
Sections
E.A.F. / Con Cast
Blooms/Billets
Normal Strength
Higher Strength
As below
carbon, carbon manganese
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
160
25
25
Oddzial w Dabrowie Gorniczej
Al. J. Pilsudskiego 92
41-308 Dabrowa Gornicza
Tel: +48 32 776 87 14 Fax: +48 32 776 84 86
Email wojciech.michalczyk@arcelormittal.com
Web: http://www.arcelormitta.com/poland/
Certificate No. MD00/0717/0011/1 Expiry date: 05/02/2018
ARCELORMITTAL WARSZAWA Sp. z.o.o.
Katowice
Bars
ul. Kasprowicza 132
01-949 Warszawa
Tel: +48 22 835 8081 Fax: +48 22 835 8638
Email: mailto:beata.pietrzyk@arcelormittal.com
Web: http://www.arcelormittal-warszawa.com
Certificate No. MD00/0720/0008/1 Expiry date: 01/08/2018
CELSA "HUTA OSTROWIEC" Sp. z o.o.
Katowice
ZAKLAD WYROBOW KUTYCH
ul. Samsonowicza 2
27-400 Ostrowiec Swietokrzyski
Tel: +48 (0)41 2492390 Fax: +48 (0)41 2493779
EMail:mdunaj@celsaho.com
Web page http://www.celsaho.com
Certificate No. MD00/2006/0007/1 Expiry date: 25/10/2016
Ingots size maximum 130 MT 2.33 m diameter
CMC POLAND Sp. z.o.o.
Katowice
ul. Pilsudskiego 82
42-400 Zawiercie
Tel: +48 32 672 5353 Fax: +48 32 672 5134 Mobile: +48 695 105211 Email: anna.slomka@cmc.com Web: www.cmcpoland.com
Certificate No. MD00/3594/0005/1 Expiry date: 05/05/2018
Approval for sections covers wide flats to 200mm width and flat bars to 150mm width.
.
FERROSTAL LABEDY Sp. z o.o.
Katowice
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Billets
As below
carbon, carbon-manganese, alloy
160
Semi-Finished
Rolled Billets
Rolled Round Bars
Normal Strength
Higher Strength
Structural
Machinery
Carbon, Carbon-Manganese, Alloy
Carbon, Carbon-manganese, Alloy
A, B
AH27S, AH32, AH36, DH27S, DH32, DH36
carbon, carbon-manganese
carbon, carbon-manganese, alloy
300
250
20
20
250
250
ul. Zawadzkiego 47
44-109 Gliwice
Tel: +48 32 234 7600 Fax: +48 32 234 7650 Mob +48 508032685
EMail mailto:biuro@ferrostal.com.pl
Web page http://www.ferrostal.com.pl
Certificate No. MD00/2307/0006/1 Expiry date: 30/03/2017
HUTA BANKOWA Sp. z o.o.
Katowice
Sections
Bars
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
66
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Katowice
Bars
Chain Cable Stock
U1, U2
160
Plates
Normal Strength
Higher Strength
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
A/304L
100
100
Poland
HUTA BANKOWA Sp. z o.o.
ul. Sobieskiego 24
41-300 Dabrowa Górnicza
Tel +48 32 295 7477
Email: a.krawczyk@hutabankowa.pl;w.paterek@hutabankowa.pl
Web http://www.hutabankowa.com.pl
Certificate No. MD00/0716/0009/1 Expiry date: 04/03/2019
HW PIETRZAK HOLDING Sp. z o.o.
Katowice
Boiler & Pressure Vessel
Clad
40
100
50
Oddzial Walcownia Blach Batory w Chorzowie
ul. Lesna 42
41-506 Chorzów
Tel: +48 604936263 or +48 32 7722525
email: beata.brzoza-kwiatek@p-h.pl
web: www.pietrzak-holding.pl
All plates with specified through thickness properties
Certificate No. MD00/2766/0007/1 Expiry date: 17/10/2016
ISD HUTA CZESTOCHOWA Sp. z o.o.
Katowice
Steelmaking
Semi-Finished
Plates
E.A.F. / Con Cast
Slabs
Blooms
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
carbon, carbon-manganese
carbon, carbon-manganese
E
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR, 460AR, 460FG, 490FG, 510FG
360FG, 410FG
250
280
50
75
50
50
75
ul. Kucelinska 22
42-207 Czestochowa
Above plate grades may also be supplied with Z25/Z35 through thickness property requirements.
Tel: +48 34 323 8147 Fax: +48 34 323 0034
Email: marketing@isd-hcz.com.pl
Web: http://www.isd- hcz.com.pl
Certificate No. MD00/0713/0013/1 Expiry date: 05/04/2018
WALCOWNIE BRUZDOWE "BATORY" Sp. z.o.o.
Katowice
Bars
Structural
Machinery
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
Steelmaking
Plates
B.O.S./Ingot/Con Cast
Normal Strength
Higher Strength
As below
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
150
150
ul. Zelazna 22
41-500 Chorzów
Tel: +48 32 241 77 38 Fax: +48 32 241 77 55
email sowinska.lilianna@wbb.net.pl web: www.wbb.net.pl
Certificate No. MD00/3545/0003/1 Expiry date: 30/11/2017
Romania
ARCELORMITTAL GALATI S.A.
Galatz
Boiler & Pressure Vessel
100
100
40
100
Sos Smardan Nr.1
800698 Galati
Tel: +40 236 802100 Fax: +40 236 802101 Email: mailto:mariana.subtirica@arcelormittal.com Web page http://www.arcelormittal.com
Approval includes for plates with specified through thickness properties, designation Z35, in all grades up to 60 mm thickness in the normalized condition.
Certificate No. MD00/0333/0008/1 Expiry date: 02/12/2016
COS TARGOVISTE S.A.
Galatz
Steelmaking
Semi-Finished
Bars
E.A.F. / Con Cast
Blooms/Billets
Chain Cable Stock
As below
carbon, carbon manganese, Alloy
U1, U2, U3
150
95
Targoviste
Sos. Gaiesti, 9-11
Jud Dambovita, 130087
Tel: +40 758 837 264 Fax: +40 245 213 322
email: dumitru.dumitru@cos-tgv.ro Web: www.cos-tgv.ro
Certificate No. MD00/2293/0006/1 Expiry date: 13/02/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
67
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
DOOSAN IMGB S.A
Galatz
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
Max Thickness/Diameter (mm)
250
250
Bars
Structural
Machinery
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
250
150
Sections
Bars
Normal Strength
Higher Strength
Normal Strength
A
AH27S, AH32, AH36, DH32, DH36
A
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Billets
carbon, carbon-manganese, alloy
alloy
carbon, carbon-manganese
Sections
Normal Strength
Higher Strength
A, B, D
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
B.O.S. / Con Cast
Slabs
carbon, carbon-manganese
Normal strength, Higher Strength
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Blooms
Bars
Chain Cable Stock
carbon, carbon-manganese
carbon, carbon-manganese, Normal Strength,
Higher Strength
U1, U2, U3
Berceni Road Nr. 104
Sector 4
041919 Bucharest
Tel: +40 21 301 2849 Fax: +40 21 301 2502
Email: mihai.ciorneanu@doosan.com
Web: www.doosanimgb.com
Certificate No. MD00/1259/0002/1 Expiry date: 09/09/2017
S.C. DONALAM S.R.L
Galatz
Str. Prelungirea Bucuresti, nr 162,
910125 Calarasi
Tel: +40 242 307 500 Fax: +40 242 306 913
email: sales@donalam.ro web: www.grupobeltrame.com
Certificate No: MD00/4439/0001/1 Expiry Date: 05/03/2018
S.C. LAMINORUL S.A. - BRAILA
Galatz
50
12
50
Sos. Industria Sarmei nr. 2
810461 Braila
Tel +40 239 669 388
Fax +40 374 092 038
Email: secretariat@laminorul.ro
Website: www.laminorul.ro
Certificate No. MD00/1916/0009/1 Expiry date: 29/03/2018
TMK-RESITA S.A.
Galatz
177
280
Traian Lalescu No. 36
Caras-Severin
Tel: +40 (0)255 217211 Fax: +40 (0)255 211883 Email: office.resita.tmk-artrom.ro
Web http://www.tmk-artrom.ro
Certificate No. MD00/3804/0003/1 Expiry date: 07/07/2019
Russia
"RM - steel" Ltd.
St. Petersburg
14
14
11, Sedova street
192019, St Petersburg
Tel: +7 812 318 0015 Fax: +7 812 568 0015
Email: mailto:info@rm-steel.com
Web http//www.rm-steel.com
Certificate No. MD00/1910/0009/1 Expiry date: 15/01/2017
CHELYABINSK METALLURGICAL PLANT PAO
St. Petersburg
20
454047- Chelyabinsk
2nd Paveletskaya ul, 14
Tel; +7 351 725 57 27 Fax: +7 351 725 51 76
email sale-chmk@mechel.ru web: www.mechel.ru
Ingots supllied as semi finished products are for further processing for forgings.
Certificate No. MD00/3262/0007/1 Expiry date: 10/08/2018
JOINT STOCK COMPANY
St. Petersburg
Steelmaking
Semi-Finished
300
"EVRAZ NIZHNY TAGIL METALLURGICAL PLANT"
1, Metallurgov Str.,
Nizhny Tagil,
Sverdlovsk Region, 622025
Tel:+007 3435 490611 Fax:+007 3435 496169 Email:mailto:alexander.ashihin@ur.evraz.com
Web http://www.ntmk.ru
Certificate No. MD00/2660/0007/1 Expiry date: 04/04/2018
JOINT STOCK COMPANY
St. Petersburg
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
68
300
80
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
"OSKOL ELECTROMETALLURGICAL PLANT"
pr. Alekseya Ugarova 218/2
309515, Belgorod
Stary Oskol
Tel +07 4725 375364 Fax +07 4725 373755 vformin@oemk.ru Web http://www.oemk.ru
Blooms as semi finished products; normal strength and higher strength; nominal 360mm maximum width x nominal 12,000mm maximum length.
Blooms as semi finished products; carbon and carbon-manganese; nominal 360mm maximum width x nominal 12,000mm maximum length.
Certificate Number: MD00/3065/0006/1 Expiry: 24/02/2019
JSC KIROVSKIY ZAVOD
St. Petersburg
Steelmaking
Bars
E.A.F/A.O.D/Ingot
Semi-finished Products
As below
carbon, carbon-manganese
120
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Slabs
As below
carbon, carbon-manganese
250
Petrostal Steel Works
47 Stachek Prospect
198097 St. Petersburg
Tel: +7 812 702 02 23 Fax: +7 812 702 04 66
email: paa@petrostal.spb.ru web: http://www.petrostal.spb.ru
Certificate No. MD00/1751/0007/1 Expiry: 29/01/2018
OJSC "Magnitogorsk Iron & Steel Works"
St. Petersburg
Steel Making and Central Laboratory
93, Kirova Street
455000 Magnitogorsk
Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: seller@mmk.ru Web http://www.mmk.ru
Approval covers for slabs as detailed above to nominal width 2520mm and nominal length 7000mm.
Certificate No. MD00/3103/0004/1 Expiry date: 26/08/2016
OJSC "Magnitogorsk Iron & Steel Works"
St. Petersburg
Hot Rolled Coil
Normal Strength
Boiler & Pressure Vessel
A
360AR, 410AR
10
10
A
360AR, 410AR
25
25
A
360AR, 410AR
10
10
A
360AR, 410AR
50
40
AH32, AH36, DH32, DH36
50
Rolling Mill 2000
Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: seller@mmk.ru Web http://www.mmk.ru
Certificate No. MD00/3834/0002/1 Expiry date: 26/08/2016
OJSC "Magnitogorsk Iron & Steel Works"
St. Petersburg
Plates
Normal Strength
Boiler & Pressure Vessel
Rolling Mill 2350
Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: seller@mmk.ru Web http://www.mmk.ru
Certificate No. MD00/3835/0002/1 Expiry date: 26/08/2016
OJSC "Magnitogorsk Iron & Steel Works"
St. Petersburg
Hot Rolled Coil
Normal Strength
Boiler & Pressure Vessel
Rolling Mill 2500
Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: seller@mmk.ru Web http://www.mmk.ru
Certificate No. MD00/3836/0002/1 Expiry date: 26/08/2016
OJSC "Magnitogorsk Iron & Steel Works"
St. Petersburg
Plates
Normal Strength
Boiler & Pressure Vessel
Rolling Mill 4500
Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: seller@mmk.ru Web http://www.mmk.ru
The approved minimum thickness is 30.0mm
Certificate No. MD00/3837/0002/1 Expiry date: 26/08/2016
OJSC "Magnitogorsk Iron & Steel Works"
Rolling Mill 5000
455000, Magnitogorsk
St. Petersburg
Plates
Higher Strength
Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: seller@mmk.ru Web http://www.mmk.ru
Certificate No. MD00/4348/0001/1 Expiry date: 25/08/2017
OJSK Novolipetsk Iron & Steel Corporation
St. Petersburg
Steelmaking
Semi-Finished
Hot Rolled Coil
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
Normal strength, Higher Strength
A, B, D
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH36, EH40
460FG, 490FG
360, 410, 360FG, 410FG
355
16
12
10
16
398040, Russia
Pl. Metallurgov 2, NLMK
Lipetsk
Tel: +7 4742 444688 Fax: +7 4742 441111
Email:mailto:info@nlmk.ru
Web:http://www.nlmk.ru
Telex: 412630NLMK RU
Certificate No. MD00/1124/0006/1 Expiry date: 06/11/2016
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
69
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
PAO SEVERSTAL
St. Petersburg
Plates
Normal Strength
Higher Strength
A, B, D, E
EH27S, EH32
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH40
360, 410
360FG, 410FG, 460FG, 490FG, 510FG
40
32
40
A
A, B, D, E
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG
15
12
12
D, E
A, B
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40
50
70
70
Boiler & Pressure Vessel
Max Thickness/Diameter (mm)
32
40
Rolling Mill 2800
30 Mira Street
162699 Cherepovets
Vologda Region
Tel: +7 8202 531146 Fax: +7 8202 53 2424 EMail: mailto:sales@stal.ru Web http://www.severstal.ru
Plates in the As Rolled, Normalized, Quenched and Tempered conditions with specified through thickness properties.
Plates in the Normalizing rolled condition to 2200mm maximum width.
Certificate #: MD00/0298/0011/1 Expiry date : 12/06/2019
PAO SEVERSTAL
St. Petersburg
Plates
Hot Rolled Coil
Normal Strength
Normal Strength
Higher Strength
Boiler & Pressure Vessel
12
Rolling Mill 2000
30 Mira Str
Tel: +7 8202 53 11 46 Fax: +7 8202 53 24 24
EMail: sales@stal.ru Web http://www.severstal.ru
Certificate No. MD00/2801/0008/1 Expiry date: 12/06/2019
PAO SEVERSTAL
St. Petersburg
Plates
Normal Strength
Higher Strength
Rolling Mill 5000
1, Lenina Prospect
"IZHORSKIE ZAVODY"
196651 Kolpino
St Petersburg
Tel: +7 8202 53 11 46 Fax: +7 8202 53 24 24 EMail: mailto:sales@stal.ru Web http://severstal.ru
Plates with specified through thickness properties
Certificate #: MD00/2802/0007/1 Expiry date: 12/06/2019
PAO SEVERSTAL
St. Petersburg
Steelmaking
Semi-Finished
B.O.S. / Con Cast
E.A.F. / Con Cast
Slabs
As below
As below
carbon, carbon-manganese
E.A.F/A.O.D/Ingot
E.A.F./Ingot/Con Cast
Normal Strength
As below
As below
B, D
A
AH32, AH36
360FG, 410FG, 460FG, 490FG, 510FG
315
B.O.S and E.A.F Workshops
30, Mira Street
162699 Cherepovets
Vologda Region
Tel: +7 8202 53 11 46 Fax: +7 8202 53 24 24
Email: sales@stal.ru Web http://severstal.ru
Certificate #: MD00/3821/0003/1 Expiry date: 12/06/2019
URAL STEEL Open Joint-Stock Company
St. Petersburg
Steelmaking
Plates
Higher Strength
Boiler & Pressure Vessel
40
50
40
40
1, Zavodskaya Street
Novotroitisk
Orenburg Region
462353
Tel: +7 3537 66 20 66 Fax: +7 3537 66 25 27 Email: mailto:d.bochkov@uralsteel.com
Certificate No. MD00/2337/0008/1 Expiry date: 31/03/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
Web: http://www.uralsteel.com
70
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Beograd
Steelmaking
Semi-Finished
Hot Rolled Coil
Plates from coils
B.O.S. / Con Cast
Slabs
Normal Strength
Normal Strength
As below
As below
A, B, D
A, B, D
200
15
15
Steelmaking
B.O.S. / Con Cast
Semi-Finished
Plates
Ingots (tonnes)
Normal Strength
Boiler & Pressure Vessel
Normal Strength
Boiler & Pressure Vessel
A, B, D, E, AH32, AH36, DH32, DH36, EH32,
EH36
carbon, carbon-manganese
A, B
360AR, 410AR
A, B, D
360, 410, 360FG, 410FG
220
12
12
12
12
Serbia
ZELEZARA SMEDEREVO D.O.O.
Radinac
11300 Smederevo
Tel: +381 26 224 459 email: ODjodjevic@zelsd.rs
Certificate No. MD00/0360/0007/1 Expiry date: 15/03/2019
Slovak Republic
U.S. Steel Kosice, s.r.o.
Prague
Hot Rolled Coil
Vstupny areal U.S. Steel
044 54 Kosice
Tel: +421 55 673 4731 Fax: +421 55 675 4731 Email: mailto: jdarsova@sk.uss.com Web: http:www.usske.sk
Certificate No. MD00/1649/0007/1 Expiry date: 17/06/2017
Semi-finished products in carbon and carbon-manganese steels in all normal strength grades and higher tensile strength grades up to EH36 with maximum
dimensions 1540mm wide to 12000mm long and thickness as stated.
ZELEZIARNE PODBREZOVA A.S.
Prague
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Blooms/Billets
As below
carbon, carbon manganese
Steelmaking
E.A.F. / Con Cast
B.O.S/V.O.D./Con Cast
Slabs
Normal Strength
Higher Strength
carbon, carbon-manganese
austenitic stainless
carbon, carbon-manganese, austenitic stainless
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR, 360, 410, 360FG, 410FG, 460FG,
490FG, 510FG
304L, 316L, 317L, 321, 347
280
Kolkáreñ 35
976 81 Podbrezova
Tel: +421 48 645 4040 Fax: +421 48 645 4041
email: turis@zelpo.sk web: www.zelpo.sk
Certificate No. MD00/1464/0004/1 Expiry date: 04/12/2016
Slovenia
ACRONI, d.o.o.
Zagreb
Semi-Finished
Plates
Boiler & Pressure Vessel
Austenitic Stainless
250
40
40
40
70
Member of Slovenian Steel Group
Cesta Borisa Kidrica 44
SI - 4270 Jesenice
Tel: +385 4 584 1040 Fax: +385 4 584 1068 Email: mailto:askube@acroni.si
Certificate No. MD00/1391/0008/1 Expiry date: 25/10/2016
METAL RAVNE d.o.o.
Zagreb
Web: http://www.acroni.si
Steelmaking
Sections
Bars
E.A.F. / Ingot
Normal Strength
Normal Strength
carbon, carbon-manganese, austenitic stainless
A, B
A, B
20
120
Koroška cesta 14
2390 Ravne na Koroškem
Tel: +386 2 870 7200 Fax: +386 2 870 7219
Email: stanko.triglav@metalravne.com Web: http://www.metalravne.com
Certificate No. MD00/2889/0005/1 Expiry date: 31/05/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
71
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Johannesburg
Steelmaking
Semi-Finished
Plates
B.O.S./E.A.F./Con Cast
Slabs
Normal Strength
As Below
As below
B, D, E
A
AH32, AH36, DH32, DH36, EH32, EH36, FH32,
FH36
360FG, 410FG, 460FG, 490FG, 510FG
360AR, 410AR
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,
LTEH36, LTFH32, LTFH36
South Africa
ARCELORMITTAL SOUTH AFRICA LTD.
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
240
30
50
30
30
40
30
Vanderbijlpark Steel
Delfos Boulevard
Vanderbijlpark, 1911
PO Box 2, Vanderbijlpark 1900
Tel +27 (0)16 889 2657 Fax +27 (0)16 889 5019
Email: mailto:allen.pass@arcelormittal.com
Web:http://www.arcelormittal.com
Certificate No. MD00/1404/0009/1 Expiry date: 07/05/2017
Spain
ACERINOX EUROPA S.A.U.
Cadiz
Steelmaking
Plates
Coil
E.A.F. / Con Cast
Austenitic Stainless
Austenitic Stainless
As below
304L, 316L, 321, 347
304L, 316L, 321, 347
Steelmaking
Bars
E.A.F. / Con Cast
Austenitic Stainless
austenitic stainless
304L, 316L, 321
Steelmaking
Semi-Finished
E.A.F/A.O.D/Ingot
Blooms
As below
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless, Ferritic Stainless
Steel*, Martensitic Stainless Steel*
carbon, carbon-manganese, alloy, austenitic
stainless, duplex Stainless, Ferritic Stainless
Steel*, Martensitic Stainless Steel*
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless, Ferritic Stainless
Steel*, Martensitic Stainless Steel*
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless, ferritic stainless*,
martensitic stainless*
50
20
Palmones
11379 Los Barrios
Cadiz
Tel: +34 956 629474 Fax: +34 956 629311
email: auxiliadora.heredia@acerinox.com web: www.acerinox.com
Certificate No. MD00/0057/0008/1 Expiry date: 15/12/2016
ACEROS INOXIDABLES OLARRA S.A.
Bilbao
100
Larrabarri, 1
48150 Larrondo-Loiu
Vizcaya
Tel: +34 617 464 872 Fax: +34 944 531 392
email: marian.tejedo@olarra.com web: www.olarra.com
Certificate No. MD00/1753/0007/1 Expiry date: 07/09/2018
ACERÍA DE ALAVA, S.A.
Bilbao
Billets
Bars
Bars
Structural
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Slabs
470
470
470
360
(ACERALAVA)
Poligono Industrial De Saratxo
01470 Amurrio
Alava
Tel: +34 94 671 93 00 Fax: +34 94 672 50 62
email: carrieta@tubacex.es
* accepted for approved applications.
Approval also includes ingots in above grades up to 5 tonne.
Certificate No. MD00/0054/0007/1 Expiry date: 19/01/2019
ARCELOR MITTAL ESPAÑA
Gijon
carbon, carbon-manganese
carbon, carbon-manganese
280
Factoria de Avilés
Apartado 90
33402 Avilés
Asturias
Tel: +34 985 187299
Email: mailto:juan-manuel.vigil@arcelormittal.comWeb page http://www.arcelormittal.com
Certificate #: MD00/0460/0007/1 Expiry date: 29/08/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
72
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
ARCELOR MITTAL ESPAÑA
Bilbao
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
A, B, D, E
FH27S, FH32, FH36, FH40
AH40, DH40, EH40
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG
Max Thickness/Diameter (mm)
E.A.F. / Con Cast
Billets
Normal Strength
Higher Strength
Normal Strength
Higher Strength
As below
Normal Strength, Higher Strength
A
AH27S, AH32, AH36, DH27S, DH32, DH36
A
AH27S, AH32, AH36, DH27S, DH32, DH36
130
15
15
25
25
E.A.F. / Con Cast
Billets
Normal Strength
Normal Strength
As below
Normal Strength
A
A
180
50
35
80
25
50
80
80
Factoria de Gijón
Apartado 570
33200 Gijón
Tel: +34 985 187299 Fax +34 985 187 519
Email: juan-manuel.vigil@arcelormittal.com
Web page http://www.arcelormittal.com
Certificate No. MD00/1804/0013/1 Expiry date: 23/09/2017
Plates with specified through thickness properties notation Z35 may be added
ARCELORMITTAL ZARAGOZA S.A.
Bilbao
Steelmaking
Semi-Finished
Sections
Bars
Avda. José Lopez Soriano No.100
Parque Tecnológico de Reciclado "Lopez Soriano"
Ctra. Torrecilla de Valmadrid Km 1.95
B° La Cartuja Baja 50720 Zaragoza
Tel No: +34 976 466171 Fax No +34 976 517648
Email: meruane.lakehal@mb.arcelor.com
Web www.arcelormittal.com
Certificate No: MD00/4183/0004/1
Expiry date 18/06/2019
COMPAÑÍA ESPAÑOLA DE LAMINACIÓN, S.L.
Barcelona
Steelmaking
Semi-Finished
Sections
Bars
C/ Ferralla, 12
Poligono Industrial 'San Vicente' s/n
08755 Castellbisbal
Barcelona
Tel: +34 618 695 319 / +34 939 730 400 Fax: +34 93 817 6676
Email: s.cabrenzo@gcelsa.com Web:http://www.celsa.com
Billets with nominal 180mm maximum width x nominal 12000mm length to the above maximum thickness
Certificate Numberr: MD00/0343/0009/1 Expiry: 20/03/2019
GERDAU ACEROS ESPECIALES EUROPA S.L.
(GERDAU)
Bilbao
Steelmaking
E.A.F. / Con Cast
As below
Semi-Finished
Blooms
As below
350
Bars
Machinery
carbon, carbon-manganese, alloy
100
Chain Cable Stock
R3, R3S, R4, API-2F, R5
78
U2, U3
100
Planta Basauri
Bo. Ugarte, S/N
P.O. Box 76
48970 Basauri (Vizcaya)
Tel +34 944 871 726 Fax +34 944 871826
Email: mailto:jorge.bas@gerdau.es
Web: www.gerdau.es
The approval for bars for chain cable stock grades; R3; R3S; R4; R4S; R5 are restricted to supply to Vicinay Cadenas SA to the applicable purchasing
specification; MPR3; MPR3S; MPR4; MPR4S ;MPR5.
The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval was
granted.
Certificate Number: MD00/0051/0010/1 Expiry: 21/01/2018
GERDAU ACEROS ESPECIALES EUROPA S.L.
(GERDAU)
Bilbao
Steelmaking
E.A.F. / Ingot
As below
Bars
Normal Strength
A
220
Machinery
carbon, carbon-manganese, alloy
230
Chain Cable Stock
R3, R3S, R4, API-2F, R4S
185
R5
230
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
73
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
Planta Reinosa
Paseo Alejandro Calonje, 1
39200 Reinosa (Cantabria)
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Tel: +34 942 775 004 Fax: +34 942 775 283
email: javier.cantero@gerdau.es web www.sidenor.com
Certificate Number: MD00/0546/0014/1 Expiry: 19/06/2017
The approval for bars for chain cable stock grades; R3; R3S; R4; R4S; R5 are restricted to supply to Vicinay Cadenas SA to the applicable purchasing
specification; MPR3; MPR3S; MPR4; MPR4S; MPR5.
The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval was
granted.
The scope of approval for bars in grade R4 includes bars to 130mm diameter produced with con cast steel manufactured at Gerdau Aceros Especials Europa SL
Planta Basauri.
The scope of approval for bars in grade R5 includes bars to 175mm diameter produced with con cast steel manufactured at Gerdau Aceros Especials Europa SL
Planta Basauri.
GERDAU ACEROS ESPECIALES EUROPA S.L.
(GERDAU)
Bilbao
Bars
Machinery
carbon, carbon-manganese, alloy
200
Chain Cable Stock
R4
117
R3, R3S
123
R5
150
U1, U2, U3
152
Planta Azcoitia
Ctra. de Zumárraga, s/n
20720 Azcoitia
Guipúzcoa
Tel: +34 943 025206 Fax: +34 943 025299 Mob:+34 647 371 029
Email: mailto:juan.aizpuru@gerdau.es
Web:http//:www:gerdau.es
The approval for bars for chain cable stock grades; R3; R3S; R4 are restricted to supply to Vicinay Cadenas SA to the applicable purchasing specification; MPR3;
MPR3S; MPR4.
The approval for bars for chain cable stock grade R5 is restricted to supply to Vicinay Cadenas S.A. to purchasing specification MPR5, this approval is with bars
to 150mm rolled from steel made at Gerdau Aceros Especiales Europa S.L. Planta Basauri and for bars to 78 mm diameter which has been manufactured from
ingots supplied by Gerdau Aceros Especiales S.L. Planta Reinosa and rolled by Gerdau Aceros Especiales S.L. Planta Azcoitia.
The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval was
granted.
Certificate Number: MD00/0620/0012/1 Expiry: 27/03/2017
LAMINADOS LOSAL, S.A.
Bilbao
Sections
Normal Strength
Higher Strength
B
A
DH32, DH36, EH32, EH36, FH32, FH36
AH32, AH36
11
50
11
38
Bekoibarra, 9
P.O. Box 17
48300 - Gernika
Tel: +34 946251400 Fax: +34 946254976 Mob: +34 68 6942188
email: agonzalez@losal.es / basterrechea@losal.es
web: www.losal.es
Certificate No. MD00/0993/0009/1 Expiry date: 18/01/2017
RUGUI MELT S.L.U.
Bilbao
Steelmaking
Semi-Finished
IF/LF/V.O.D./Con Cast
Billets
As Below
carbon, carbon-manganese
165
Sections
Normal Strength
Higher Strength
A
AH32, AH36, DH32, DH36
30
30
Poligono Industrial Emiliano Revilla
Avenida de España, n° 21
42110 Olvega (Soria)
Tel no: +34 943 85 7311
fax no: +34 943 85 7312
Email: iurbieta'rugui.com
Web: www.rugui.com
certificate No: MD00/4352/0001/1 Expiry date 25/06/2017
RUGUI OLVEGA S.L.U
Bilbao
Poligono Industrial Emiliano Revilla,
Avenida de España No. 1,
42110 Olvega (Soria),
Tel: +34 943 8573 11 Fax: +34 943 85 73 12
email: sales@rugui.com www.rugui.com
Certificate No. MD00/4435/0001/1 Expiry Date: 25.02.2018
Approval is for wide flats (flat bars) up to a maximum width of 300mm.
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
74
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
RUGUI S.L.
Bilbao
Sections
Normal Strength
Higher Strength
A
AH32, AH36, DH32, DH36
Max Thickness/Diameter (mm)
Semi-Finished
E.A.F. / Con Cast
E.A.F. / Ingot
Ingots (tonnes)
Blooms
Billets
Bars
Bars
Structural
Machinery
austenitic
austenitic
austenitic
austenitic
austenitic
austenitic
austenitic
austenitic
austenitic
25
40
Poligono Industrial Basarte
20720 Azcoitia ( Guipuzcoa)
Apdo. de Correos no. 8 Azpeitia ( Guipuzcoa)
Tel: +34 943 857311 Fax: +34 943 857312
Email: mailto:rugui@rugui.com
Web http://www.rugui.com
The approved sections are in the form of flat bars up to a maximum width of 200mm.
Certificate No. MD00/1915/0007/1 Expiry date: 05/02/2017
Sweden
AB SANDVIK MATERIALS TECHNOLOGY
Gothenburg
Steelmaking
stainless,
stainless,
stainless,
stainless,
stainless,
stainless,
stainless,
stainless,
stainless,
duplex
duplex
duplex
duplex
duplex
duplex
duplex
duplex
duplex
stainless
stainless
stainless
stainless
Stainless
stainless
stainless
stainless
stainless
6
265
150
195
185
185
185
SE-811 81 Sandviken
Tel: +46 (0) 26 263311
email: erik.k.janssons@sandvik.com web: www.smt.sandvik.com
Certificate No. MD00/2173/0007/1 Expiry date: 29/10/2018
Semi Finished products austenitic and duplex stainless steel con-cast Blooms to 365mm wide, to 7500mm long; Con-cast Billets to 150mm wide, to 6200mm long;
As rolled billets to 195mm wide, to 6000mm long; semi-finished as rolled bars to 185mm diameter, 6900mm long for further processing for Rolled, Forged
Products
OUTOKUMPU STAINLESS AB
Gothenburg
Steelmaking
Plates from coils
E.A.F. / Con Cast
Austenitic Stainless Steel
Duplex Stainless
Coil
Austenitic Stainless
Duplex Stainless
Coil
Austenitic Stainless
As below
304L, 304LN, 316L, 321, 347
UNS S31803, UNS S32205*, UNS S32101*, UNS
S32304*
304L, 316L, 321, 347, 304LN
UNS S31803, UNS S32205, UNS S32101*, UNS
S32304*
13
8
13
8
Business Area Coil EMEA
Avesta Works
Box 74
SE-774 22 Avesta
Tel: +46 (0)226 810 00
E-mail: johan.nordstrom@outokumpu.com
Web: http://www.outokumpu.com
*accepted for approved applications
Certificate No. MD00/0131/0010/1 Expiry date: 06/12/2017
OUTOKUMPU STAINLESS AB
Gothenburg
Duplex Stainless
1.4439
304L, 316L, 317L, 321
UNS S32205, 1.4462, 1.4362*
2
5
2
Special Coil Nyby
SE-64480 Torshälla
Tel +46 (0)1634 9000 Fax +46 (0)1634 9014 Email: mailto:claes.gefvenberg@outokumpu
Certificate No. MD00/0132/0006/1 Expiry date: 29/01/2016
OUTOKUMPU STAINLESS AB
Gothenburg
Plates
Austenitic Stainless
Duplex Stainless
304L, 304LN, 316L, 316LN, 321
UNS S32304*
UNS S31803(MOD)*
50
10
50
Business Unit Special Plate,
Quarto Plate Europe,
S-693 81 Degerfors,
Tel: 46 586 471 04 Mob: +46 70 564 4810
email: karin.ozols@outokumpu.com web: www.outokumpu.com
* accepted for approved applications
** Grade UNS 32304 may be accepted as equivalent to 316L as shown in LR Rules when properties meet the Rule requirements.
* Avesta 2205, UNS 32205 and EN 10088-1 grade 1.4462 may be accepted as equivalent to UNS 31803 as shown in LR Rules when properties meet the Rule
requirements.
Certificate Number MD00/1754/0007/1 Expiry date: 13/11/2017
OUTOKUMPU STAINLESS AB
Degerfors Stainless
SE-693 81 Degerfors
Gothenburg
Bars
Duplex Stainless
UNS S31803, UNS S32205*
200
Tel: +46 (0)586 47000/47 232 Fax: +46 (0)586 47008
Email: jorgen.johansson@outokumpu.com
Web http://www.outokumpu.com
EN 10088-1 grade 1.4462 accepted for approved applications only.
Certificate number MD00/3144/0006/1 Expiry date: 07/06/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
75
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
OVAKO BAR AB.
Gothenburg
Sections
Normal Strength
Higher Strength
Bars
Normal Strength
Higher Strength
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
Max Thickness/Diameter (mm)
50
50
45
45
Boxholm Works
Box 5
59010 Boxholm
Tel: +46 (0)240 668062 Fax: +46(0)240 668168 Mobile: +46 (0)70 3769320 Email mailto: thomas.carlsont@ovako.com
Certificate No. MD00/0560/0009/1 Expiry date: 26/09/2017
OVAKO BAR AB.
Gothenburg
Steelmaking
Sections
Bars
Web http://www.ovako.com
E.A.F. / Con Cast
Normal Strength
Higher Strength
Normal Strength
Higher Strength
Machinery
As below
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
A, B, D, E
AH32, AH36, DH32, DH36, EH32, EH36
carbon, carbon-manganese
E.A.F. / Ingot
Billets
Bars
Structural
Machinery
Chain Cable Stock
As below
carbon, carbon-manganese,
carbon, carbon-manganese,
carbon, carbon-manganese,
carbon, carbon-manganese,
U1, U2, U3, R3, R3S, R4
50
50
93
93
93
Smedjebacken Works
S-777 80 Smedjebacken
Tel. +46 240 668000 Fax +46 (0)240 668168
email thomas.carlsson@ovako.com web www.ovako.com
Certificate #: MD00/0561/0007/1 Expiry date: 09/06/2019
OVAKO SWEDEN AB, BU BAR Hofors-Hällefors
Gothenburg
Steelmaking
Semi-Finished
Bars
alloy
alloy
alloy
alloy
400
450
190
170
165
Se-813 82 HOFORS
Tel: +46 (0) 298 25000 Fax: +46 0290 591606
Email: christian.andersson@ovako.com
Web: www.ovako.com
Certificate No. MD00/1167/0010/1 Expiry date: 26/11/2017
Bars >75mm of grades R3, R3S and R4 supplied for mooring chain cable to Ramnas Bruk AB, Ramnas and Ljusne works. Ovako Grade 316R up to 160mm
diameter approved for R3 mooring chain.
SCANA STEEL BJÖRNEBORG AB
Gothenburg
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy
75
Kristinehamnsvägen 2
S-68071 Björneborg
Tel: +46 550 251 30 Fax: +46 550 269 5884
email: fredrik.gunnberg@cana.no web: www.scana.no
Ingots as semi-finished products to the above maximum weight; nominal; 2070/2230mm diameter x 2600mm; are approved for further processing for forgings.
Certificate Number: MD00/2769/0003/1 Expiry: 03/08/2018
SSAB EMEA AB
Gothenburg
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
As below
As below
A, B, D, E
FH27S
AH27S, AH32, AH36, AH40, AH42, DH27S,
DH32, DH36, DH40, EH27S, EH36
DH42, EH32, EH40, EH42, FH32, FH36, FH40,
FH42
AH46, AH50, AH55, AH62, AH69, DH46, DH50,
DH55, DH62, DH69, EH46, EH50, EH55, EH62,
EH69, FH46, FH50, FH55, FH62, FH69
460FG, 490FG, 510FG
360FG, 410FG
LTAH27S, LTAH32, LTAH36, LTAH40,
LTDH27S, LTDH32, LTDH36, LTDH40,
LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,
LTFH32, LTFH36, LTFH40
286
75
40
60
70
80
60
75
40
OXELÖSUND
S-61380 Oxelösund
Tel: +46 155 25 58 10 Mobile: +46 703 472 363 Fax: +46 155 25 41 23 Email: mailto:per.hofslagare@ssab.com
Web:http://www.ssab.com
All plates with specified through thickness properties.
Semi-finished products in carbon and carbon-manganese steel with fine grain (element combinations as stated), slabs to 1680 mm wide, to 11000mm long of
maximum weight 30T for further processing to rolled products
Materials Quality Scheme Approved - Approval No. MQS 049
Certificate No. MD00/1282/0011/1 Expiry date: 24/04/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
76
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
SSAB EMEA AB
Gothenburg
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Slabs
As below
Normal strength, Higher Strength
Max Thickness/Diameter (mm)
220
LULEÅ
97188 Luleå
Tel: +46 920 920 00 Email to: ssab.lulea@ssab.com We http://www.ssab.com
Slabs as semi finished products nominal 800-1700mm width x nominal 11000mm length to the above maximum thickness are approved for further processing for
rolled products.
Certificate No.: MD00/4194/0001/1 Expiry date: 02/07/2016
Taiwan, Republic of China
CHINA STEEL CORPORATION
Kaohsiung
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
Normal strength, Higher Strength
A, B, D, E
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40, EH47
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
270
50
75
40
50
No.1 Chung Kang Road
Hsiao Kang
Kaohsiung
Tel: +886 7 802 1111 ext 2208 Fax: +886 7 805 1292
Email: 54338@mail.csc.com.tw
Web page: www.csc.com.tw
All grades are approved with specified with through thickness properties.
Certificate No. MD00/0304/00012/1 Expiry date: 03/07/2017
DRAGON STEEL CORPORATION
Kaohsiung
Steelmaking
Sections
E.A.F. / Con Cast
Higher Strength
As below
AH32, AH36, DH32, DH36
26
100, Longchang Road,
Longjing Dist.,
Taichung City
Tel: +886 4 2630 6088 Ext. 8705 Fax: +886 4 2630 6041 Email:020288@dragonsteel.com.tw
Web www.dragonsteel.com.tw
Billets / Blooms as semi-finished products to the above maximum thickness x nominal 750mm maximum width x nominal 12000mm maximum length
Sections produced are H beam sections to the above maximum thickness x 900mm x 300mm overall dimensions x nominal 19000mm maximum length.
Certificate Number: MD00/3768/0005/1 Expiry: 01/04/2019
T. S. STEEL COMPANY LTD.
Kaohsiung
Sections
Bars
Normal Strength
Higher Strength
Normal Strength
A
AH32, AH36
A
15
12
25
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Blooms/Billets
As below
carbon, carbon manganese, Normal Strength,
Higher Strength
No.6 Kon-Sixth Road
Tsuang-Hine Industrial Zone
Hsen-Kang Road
Chang-Hua Hsien
Tel: +886 4 798 0060 Fax: +886 4 799 1522
email: fang123@tssteel.com.tw
Certificate No. MD00/2313/0007/1 Expiry date: 09/04/2017
TUNG HO STEEL ENTERPRISE CORP.
Taipei
430
Miao Li Works
No.22, Pingding Erhu Village,
Sihu Township,
Miaoli County 36842,
Tel: +88 637 923333 ext197 Fax: +88 637 922994 Email mailto:h32dkj@tunghosteel.com Web http://www.tunghosteel.com
Certifcate Number: MD00/3719/0004/1 Expiry date: 15/12/2018
TUNG HO STEEL ENTERPRISE CORP.
Taipei
Sections
Normal Strength
Higher Strength
A
AH27S, AH32, AH36
18
18
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Slabs
Billets
austenitic stainless, duplex stainless
austenitic stainless, duplex stainless
austenitic stainless, duplex stainless
Kaohsiung Works
No. 8, Jiaxing Street,
Xiaogang Dist.
Kaohsiung City, 81257
Tel: +88 6 7802 3131 Fax: +88 6 801 0696
Email: k23@tunghosteel.com Web http://www.tunghosteel.com
Certificate Number: MD00/3720/0004/1 Expiry: 14/12/2018
WALSIN LIHWA CORP.
Kaohsiung
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
77
200
240
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Yenshui Plant
No. 3-10, Shi Jou Liau
Chin Shuei Li
Yenshui District
Tainan City 73743
Tel +886 (0)6 6520911 ext. 5802 Fax +886 (0)6 6520933 Email mailto:eddy_huang@walsin.com Web http://www.walsin.com
Certificate No. MD00/3063/0005/1 Expiry date: 14/03/2019
Semi Finished Products Austentic & Duplex Stainless slabs to 1300mm wide, to 12000mm long; square billets to 155mm wide, 12000mm long; round billets with
maximum diameter 240mm , to 12000mm long
Thailand
LPN PLATE MILL PUBLIC COMPANY LIMITED
199/9 Moo 4 Suksawad Road
Bangkok
Plates
Normal Strength
A
50
Plates
Normal Strength
A
40
Hot Rolled Coil
Normal Strength
B, D
Pakklong Bangplakod
Prasamutjedee
Samutprakarn 10290
Tel: +66 2815 6400-9 Fax: +66 2815 6415
Email: mailto:labtest@lpngroup.co.th
Web: www.lpnpm.co.th
Certificate No. MD00/2578/0007/1 Expiry date: 01/09/2017
SAHAVIRIYA PLATE MILL PUBLIC COMPANY
LIMITED
Chachoengsao
160 Moo 14 Sukhumvit Road
Bangpakong
Chachoengsao 24130
Bangkok
Tel: +66 38883 2056 60 Fax: +66 3853 1635
Email: chainarong.t@spm-plate.com
Web: www.spm-plate.com
Certificate No. MD00/3952/0002/1 Expiry date: 01/09/2017
SAHAVIRIYA STEEL INDUSTRIES PUBLIC
COMPANY LIMITED
Bangkok
8
A
19
Boiler & Pressure Vessel
360AR, 410AR
19
Steelmaking
E.A.F. / Ingot
As below
Semi-Finished
Ingots (tonnes)
carbon, carbon-manganese, alloy
11
Slabs
carbon, carbon-manganese, alloy
320
Blooms
carbon, carbon-manganese, alloy
400
Billets
carbon, carbon-manganese, alloy
185
Prachuab Kirikhan
9M.7 Tumbol Mearumphueng
Amphur Bang Saphan
Prachuab Kirikhan 77140
Tel: (+66) 32 691403 Fax: (+66) 32 691408
Email mailto: NavaC@ssi-steel.com
Web http://www.ssi-steel.com
Certificate No. MD00/3764/0003/1 Expiry date: 22/09/2018
The Netherlands
NEDSTAAL B.V.
Haren
(Groningen)
Rapenburg 1
NL 2952 AP
Alblasserdam
Tel: +33 (0) 78 692 3700 Fax: +31 (0) 78 692 3712 Email mailto:h.zuilen@nedstaal.nl & c.gortz@nedstaal.nl Web: http://www.nedstaal.nl
The above semi finished products to the indicated maximum weight/ thickness are approved for further reprocessing for forgings; ingots nominal maximum
dimensions 940mm x 780mm x 2300mm long; slabs nominal 620mm wide x nominal 3300mm long; billets nominal 185mm wide x 9200mm long; blooms
nominal 220mm wide x 13100mm long.
Certificate Number: MD00/3010/0005/1 Expiry: 10/09/2018
TATA STEEL IJMUIDEN B.V
Haren
(Groningen)
Steelmaking
B.O.S. / Con Cast
As below
Semi-Finished
Slabs
carbon, carbon-manganese
Plates
Normal Strength
A, B
20
Hot Rolled Coil
Normal Strength
A, B
20
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
78
225
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
IJmuiden Works
Postbus 10000
1970 CA IJmuiden
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Fabricated Sections
Normal Strength
Higher Strength
A
AH32, AH36
Steelmaking
Semi-Finished
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Bars
Blooms/Billets
Structural
Machinery
As below
carbon-manganese, alloy
carbon
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
Tel +31 2514 92110 Fax +31 2514 70414
Email: jelle.van-der-wal@tatasteel.com
web: www.tatasteel.nl
Certificate No. MD00/0698/0009/1 Expiry date: 28/09/2018
Tunisia
PALESCANDOLO CNT sarl
Genoa
25
25
Parc D' Activite' Economique De Bizerte
7000 Bizerte
Tel: + 21 77 241 7292 Fax: +21 77 241 7552 Email: apalescnt@yahoo.fr
Certificate Number: MD00/4018/0002/1 Expiry: 25/04/2018
Turkey
ASIL CELIK SANAYI VE TICARET A.S.
Istanbul
1
2
600
300
240
Gemic Koyu Mevki 16800
Orhangazi, Bursa
Tel: +90 224 280 62 60 Fax: +90 224 280 62 00
email bulent.ozmel@asilcelik.com.tr web www.asilcelik.com.tr
Certificate No. MD00/1921/0007/1 Expiry date: 03/05/2019
Machinery bars approved to 220mm diameter from ingot route, and to 240mm diamter from concast route.
EREGLI DEMIR VE CELIK FABRIKALARI T.A.S.
Istanbul
Steelmaking
Plates
B.O.S. / Con Cast
Normal Strength
Higher Strength
Hot Rolled Coil
Boiler & Pressure Vessel
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36, FH27S, FH32, FH36
360FG, 410FG, 460FG, 490FG, 510FG
A, B, D, E
AH32, AH36, DH32, DH36, EH27S, EH32, EH36,
FH27S, FH32, FH36
360FG, 410FG, 460FG, 490FG, 510FG
60
60
60
15
15
15
KDZ. Eregli
67330
Zonguldak
Tel: +90 (0)372 329 3838 Fax: +90 (0)372 323 2598
email: kaygoren@erdemir.com.tr web: www.erdemir.com.tr
Certificate No. MD00/1951/0010/1 Expiry date: 05/05/2017
ÖZKAN DEMIR ÇELIK SANAYI A.S.
Istanbul
Steelmaking
Semi-Finished
Sections
E.A.F. / Con Cast
Blooms/Billets
Normal Strength
Higher Strength
As below
carbon, carbon manganese
D, E
A, B
AH40, DH40
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
260
12
25
19
28
Bozköy Köyü
13. Cadde N:4 35800
Aliaga-Izmir
Tel +90 232 625 1515 Fax +90 232 625 1054
Email: info@ozkansteel.com
Web: http://www.ozkansteel.com
Certificate No. MD00/2984/0005/1 Expiry date: 26/03/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
79
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Mykolaiv
Steelmaking
Semi-Finished
Plates
B.O.S./Ingot/Con Cast
Slabs
Normal Strength
As below
Normal strength, Higher Strength
D, E
B
A
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
360, 410
A
A
Ukraine
PJSC "ALCHEVSK IRON & STEEL WORKS"
Higher Strength
Boiler & Pressure Vessel
Sections
Bars
Normal Strength
Normal Strength
Steelmaking
Semi-Finished
Plates
B.O.S. / Con Cast
Slabs
Normal Strength
300
45
50
72
50
22
50
72
8
100
20A, Vylesova Str.,
Severodonetsk,
Lugansk Region,
93400
Tel: +38 06442 73382
email: abrosimov@amk.lg.ua
Certificae No: MD00/4588/0001/1 Expiry Date: 26/01/2018
PJSC "AZOVSTAL IRON & STEEL WORKS"
Mykolaiv
Higher Strength
Boiler & Pressure Vessel
As below
Normal strength, Higher Strength
D, E
A, B
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG
270
50
100
50
50
1, Leporsky St.
Mariupol 87500
Tel: +38 0629 46 86 03 Fax: +380 629 468 441
email goloborodko-kv@azovstal.com.ua web www.azovstal.metinvestholding.com
Certificate No. MD00/0779/0009/1 Expiry date: 14/02/2018
Including plates with specified through thickness properties. Z35 may be applied to all grades and thicknesses
PJSC "ENERGOMASHSPETSSTAL"
Mykolaiv
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
As below
carbon, carbon-manganese, alloy
Steelmaking
B.O.S. / Con Cast
As below
Plates
Normal Strength
A, B, D, E
50
Higher Strength
DH40, EH40
25
50
Boiler & Pressure Vessel
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR, 460AR
360FG, 410FG
50
250
84306 Kramatorsk
Donetsk Region
Tel: +38 (06264) 6-94-93 Fax: +38 (06264) 6-94-93
Email: nosenkonina@emss.dn.ua
Certificate No. MD00/3575/0002/1 Expiry date: 15/03/2018
PJSC "ILYICH IRON AND STEEL WORKS OF
MARIUPOL"
Mykolaiv
25
1 Levchenko Street
Mariupol 87504
All grades and thicknesses with specified through thickness properties. Notation Z25 or Z35 may be added.
Tel: +38 (0)0 629 56 43 98
email: sergey.paramonov@ilyichsteel.com web: www.ilyichsteel.metinvestholding.com
Certificate No. MD00/0775/0006/1 Expiry date: 02/07/2016
PJSC ELEKTROMETALLURGICAL WORKS
DNIPROSPETSSTAL
Mykolaiv
Steelmaking
E.A.F. / Ingot
As below
Bars
Austenitic Stainless
304L, 316L, 321
270
Machinery
carbon, carbon-manganese, alloy
300
Chain Cable Stock
U1, U2, U3
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
80
85
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Sections
Normal Strength
Higher Strength
Bars
Normal Strength
Higher Strength
A
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
A
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
named after A.N. Kuzmin
81 Yuzhnoye Shosse
Zaporozhye, 69008
Tel: +38 612 223 627 Fax No: +38 612 131 780
Email : OUKN@dss.com.ua
Web http://www.dss.com.ua
Including forged bars and tube blanks ( billets) in all qualities.
Certificate No. MD00/2225/0007/1 Expiry date: 03/07/2016
United Kingdom
ACENTA HOT ROLLED
Birmingham
50
32
50
50
Peartree Lane
Woodside, Dudley
West Midlands DY2 0QS
Tel: +44 (0) 1384 471 200 Email: mailto:ppowell@acentasteel.com Web: http://www.acentasteel.com
Certificate Number: MD00/2618/0008/1 Expiry: 19/02/2019
CAPARO MERCHANT BAR PLC.
Liverpool
Sections
Normal
Higher
Normal
Higher
Bars
Strength
Strength
Strength
Strength
A, B, D, E
AH32, AH36, DH32, DH36
A, B, D, E
AH32, AH36, DH32, DH36
12
12
50
50
High Strength
AH32, AH36, DH32
DH36
EH46-TM
18
30
20
E.A.F. / Con Cast
Blooms/Billets
Normal Strength
As below
Normal Strength
A
Caparo House
P.O. Box 15
Scunthorpe
DN16 1XL
Tel +44 (0)1724 403094 Fax +44 (0)1724 403044
email: mike.hill@cmbplc.co.uk web: www.cmbplc.co.uk
The approved sections include flat bar and angled bar
Certificate No. MD00/1599/0010/1 Expiry date: 25/11/2018
CELLBEAM LTD.
Liverpool
Fabricated Sections
Higher Strength
Thorp Arch Trading Estate
Wetherby
West Yorkshire LS23 7DB
Tel: +44 (0)1737 840600
Email: edward.skarret@cellbeam.co.uk
Web: www.cellbeam.co.uk
Certificate No. MD00/3534/0005/1 Expiry date: 10/11/2017
CELSA MANUFACTURING (UK) LTD.
Southampton
Steelmaking
Semi-Finished
Sections
140
25
Sections Mill
Tremorfa Works
Seawall Road,
Tremorfa,
Cardiff. CF24 5TH
Tel: +44 (0) 2920 351899
Fax: +44 (0) 2920 351868
E-mail: gary.jones@celsauk.com
Website: www.celsauk.com
Certificate No. MD00/3552/0004/1 Expiry date: 15/12/2017
Concast blooms/billets covers billets to 140mm x140mm and concast 'mini slabs' to 280 x 120mm.
LONGS STEEL (UK) LIMITED
Glasgow
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
81
E
A, B, D
FH40
FH32, FH36
AH42, AH46
AH40, DH40, DH42, DH46, EH40, EH42, EH46
AH32, AH36, DH32, DH36, EH32, EH36
460FG, 490FG, 510FG
360FG, 410FG
LTFH40
LTAH32, LTAH36, LTAH40, LTDH32, LTDH36,
LTDH40, LTEH32, LTEH36, LTEH40, LTFH32,
LTFH36
50
100
25
30
36
65
75
75
100
25
30
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
Dalzell
Motherwell ML1 1PU
LR Office
Product
Category
Tel: +44 (0)1698 266100 Fax: +44 (0) 1698 266100 Ext. 394 Email to: simon.bradley@tatasteel.com
All plates with specified through thickness properties.
Materials Quality Scheme Approved - Approval No. MQS030
Certificate No. MD00/0235/0011/1 Expiry date: 18/05/2017
LONGS STEEL (UK) LIMITED
Liverpool
Steelmaking
Semi-Finished
Plates
Grade
Max Thickness/Diameter (mm)
Web: http:\\www.tatasteel.com
B.O.S./Ingot/Con Cast
Slabs
Blooms/Billets
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Ferritic Low Temperature
As below
carbon, carbon-manganese
carbon, carbon-manganese
E
B, D
A
FH40, FH42, FH46
AH40, AH42, AH46, DH40, DH42, DH46, EH40,
EH42, EH46
FH32, FH36
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
360AR, 410AR
360FG, 410FG, 460FG, 490FG, 510FG
360, 410
LTAH27S, LTAH32, LTAH36, LTAH40,
LTDH27S, LTDH32, LTDH36, LTDH40,
LTEH27S, LTEH32, LTEH36, LTEH40
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
305
355
50
60
80
25
30
50
70
40
70
80
30
Sections
Normal Strength
Higher Strength
50
50
Sections
Normal Strength
Higher Strength
A, B, D, E
AH27S, AH32, AH36, DH27S, DH32, DH36
77
77
Sections
Normal Strength
Higher Strength
A, B, D, E
AH40, DH40
AH32, AH36, DH32, DH36, EH32, EH36
20
15
20
Scunthorpe
P.O. Box 1
Scunthorpe DN16 1BP
Tel: +44 1724 404040 Email:maito: shipbuilding@tatasteel.com
Web:http://www.tatasteel.com
All plates with through thickness properties.
Materials Quality Scheme Approved - Approval No. MQS029
Certificate #: MD00/0240/0015/1 Expiry date: 22/07/2017
LONGS STEEL (UK) LIMITED
Birmingham
Teesside
Redcar
Teesside
TS10 5RD
Tel: +44 (0)1642 406583 Fax: +44 (0)1642 406904
Email: simon.bradley@tatasteel.com
Materials Quality Scheme Approved - Approval No. MQS031
Certificate #: MD00/0242/0013/1 Expiry date: 01/06/2017
LONGS STEEL (UK) LIMITED
Birmingham
Skinningrove
P.O. Box 1
Saltburn by the Sea
TS13 4ET
Tel: +44 (0)1287 640212 Fax: +44 (0)1287 643467 Email: mailto:simon.bradley@tatasteel.com
Materials Quality Scheme Approved - Approval No. MQS032
Certificate #: MD00/0243/0010/1 Expiry date: 18/08/2017
OUTOKUMPU STAINLESS LTD.
Liverpool
Steelmaking
Semi-Finished
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
E.A.F/A.O.D/L.A.F/ConCast
Ingots (tonnes)
Slabs
Blooms
Billets
82
stainless
stainless
stainless
stainless
stainless
steel
steel
steel
steel
steel
19
300
300
200
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
LONG PRODUCTS, SMACC
P.O. Box 161
Europa Link
Sheffield, S9 1TZ
The approval for steelmaking and ingots, slabs, blooms and billets in stainless steel covers the supply of austenitic, duplex, ferritic, martensitic and precipitation
hardening grades, in accordance with the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3 or appropriate international or
national standards. The final processing mill is responsible for ordering steel which complies with their surface and internal quality standards and approved
chemical composition to enables them to achieve the required physical and mechanical properties.
Mass of slab and bloom up to 30.0T.and billet up to 20T
Tel: +44 (0)114 2616292 Fax: +44 0114 2616163
Email: mailto:richard.firman@outokumpu.com
Web: http://www.outokumpu.com
Certificate No. MD00/1883/0008/1 Expiry date: 01/01/2017
SAHAVIRIYA STEEL INDUSTRIES UK
Liverpool
Steelmaking
Semi-Finished
B.O.S. / Con Cast
Slabs
As below
carbon, carbon-manganese
Steelmaking
E.A.F. / Ingot
carbon, carbon-manganese, alloy, austenitic
stainless
Sections
Normal Strength
Higher Strength
Fabricated Sections
Structural Sections
A
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
carbon, carbon-manganese
305
Steel House
Redcar
TS10 5QW
Tel: +44 01642 408053
Email: david.reevell@ssi-steel.co.uk
Web: http://www.ssi-steel.co.uk
Certificate No. MD00/4057/0002/1 Expiry date: 21/07/2018
SHEFFIELD FORGEMASTERS INTERNATIONAL
LTD.
P.O. Box 286
Brightside Lane
Sheffield S9 2RW
Birmingham
Tel: +44 (0)114 2449071 Fax: +44 (0)114 2422103
Email:mailto:sales@sfm.com
Web:http://www.sheffieldforgemasters.com
Certificate No. MD00/0524/0008/1 Expiry date: 30/06/2017
TATA STEEL UK LIMITED
Birmingham
20
20
20
Hartlepool Works
20 Inch H.F.I. Pipe Mill
Brenda Road
Hartlepool
Teeside TS25 2EG
Tel: +44 (0)1429 527249 Mob: +44 (0)7743 842969 Email: mailto:david.evans@tatsteel.com Web:http://www.tatasteeleurope.com
Certificate #: MD00/0236/0008/1 Expiry date: 09/09/2017
TATA STEEL UK LIMITED
Birmingham
Steelmaking
Semi-Finished
Bars
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Semi-finished Products
Machinery
Chain Cable Stock
carbon, carbon-manganese, alloy
As below
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
U1, U2, U3, R3, R3S, R4
13
381
300
165
B.O.S. / Con Cast
Slabs
As below
carbon, carbon-manganese
238
Rotherham & Stocksbridge Sites
Stocksbridge
Sheffield
South Yorkshire S36 2JA
Tel: +44 (0)114 283 2000
email adam.tilley@tatasteel.com
web: www.tatasteelspeciality.com
Certificate No. MD00/1593/0007/1 Expiry date: 03/07/2017
TATA STEEL UK LIMITED
Birmingham
Steelmaking
Semi-Finished
Port Talbot Works
Port Talbot
SA13 2NG
Tel: +44 (0) 1639 872168 Fax: +44 (0) 1698 266100 Ext. 394 Web page http:\\www.tatasteeleurope.com
Approval covers concast slabs to nominal size 1850mm wide x 10,000mm long to the maximum thickness for further processing to rolled products.
Certificate No.: MD00/3909/0002/1 Expiry Date: 28.04.2017
TATA STEEL UK LIMITED
Birmingham
Fabricated Sections
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
Structural Sections
83
carbon, carbon-manganese
16
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
B.O.S. / Con Cast
Normal Strength
As below
D
A, B
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
Corby Works
P.O.Box 101, Weldon Road
Corby
Northamptonshire
NN17 5UA
Tel: +44 (0)1536 404704 Fax: +44 (0)1536 404212
Email: stewart.jeffrey@tatasteel.com Web: http://www.tatasteel.com
Includes fabricated hollow sections
Certificate No. MD00/0234/0002/1 Expiry date: 25/02/2018
United States of America
ARCELORMITTAL BURNS HARBOR
Chicago
Steelmaking
Plates
Higher Strength
35
50
75
250 West Highway 12
Burns Harbor
IN 46304-9745
Tel: +1 219 787 2854 Fax: +1 219 787 2139
email robert.spangler@arcelormittal.com web: www.arcelormittal.com
Certificate Number: MD00/2331/0007/1 Expiry: 16/12/2018
ELLWOOD QUALITY STEEL COMPANY
Philadelphia
Steelmaking
Semi-Finished
E.A.F. / Ingot
Ingots (tonnes)
carbon, carbon-manganese, alloy
carbon, carbon-manganese, alloy
77
Plates
Normal Strength
Higher Strength
Boiler & Pressure Vessel
Normal Strength
Higher Strength
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36
360AR, 410AR, 360FG, 410FG
A, B, D
AH27S, DH27S, AH32, DH32, AH36, DH36
50
30
50
19
19
Normal Strength
51
102
102
Boiler & Pressure Vessel
E
A, B, D
AH27S, AH32, AH36, DH27S, DH32, DH36,
DH40
360FG, 410FG, 460FG, 490FG, 510FG
Normal Strength
Higher Strength
Boiler & Pressure Vessel
A, B
AH32, AH36, DH32, DH36
360FG, 410FG, 460FG, 490FG, 510FG
E.A.F. / Con Cast
Rolled Round Bars
As Cast Round Section
Rolled Square Bars
As below
Carbon, Carbon-manganese, Alloy
Carbon, Carbon-manganese, Alloy
Carbon, Carbon-manganese, Alloy
700 Moravia Street
New Castle
Pennsylvania 16101
Tel: +1 724 658 6849 Fax: +1 724 658 6802
Email mailto:slubinski@elwd.com
Web: www.egi.org
Certificate No. MD00/2652/0006/1 Expiry date: 14/02/2018
EVRAZ OREGON STEEL MILLS
Seattle
Plates from coils
14400 N. Rivergate Blvd.
Portland
OR 97203
Tel: +1 503 978 6130 Fax: +1 503 978 4975
Email: mailto:Christine.wrinkle@evrazincna.com Web http://www.evrazincna.com
Including normal strength grades with specified through thickness properties (Z35)
MATERIALS QUALITY SCHEME APPROVED - MQS 047
Certificate No. MD00/1152/0007/1 Expiry date: 31/05/2018
JSW STEEL (USA) INC.
Houston
Plates
Higher Strength
102
5200 East McKinney Road
Baytown
Texas 77523
Tel: +1 281 382 5121
email mailto: rajesh.khosla@jswsteel.us
web: www.jswsteel.us
Certificate No. MD00/3505/0003/1 Expiry date: 25/08/2017
NUCOR STEEL - HERTFORD COUNTY
Norfolk,VA
Plates
51
51
51
1505 River Road
Cofield
North Carolina
27922
Tel: +1 252 356 3712
Email: sales@nucorhertford.com Web http://www.nucorhertford.com
Certificate No. MD00/4593/0001/1 Expiry date: 06/07/2019
NUCOR STEEL MEMPHIS, INC
New Orleans
Steelmaking
Semi-Finished
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
84
203
511
254
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
3601 Paul R. Lowry Road
Memphis
TN 38109
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Steelmaking
Hot Rolled Coil
E.A.F. / Con Cast
Normal Strength
Boiler & Pressure Vessel
Normal Strength
Higher Strength
As below
A
360FG, 410FG
A
AH27S, DH27S, AH32, DH32, AH36, DH36
Tel: +1 901 786 5416 Fax: +1 901 788 5300
Email: Gail.Farrow@nucor.com Web http://www.nucor.com
Certificate No. MD00/4059/0001/1 Expiry date: 22/07/2015
NUCOR STEEL TUSCALOOSA INC.
New Orleans
Plates from coils
20
20
20
13
1700 Holt Road N.E.
Tuscaloosa
AL 35404-1000
Tel: +1 205 562 1200 Fax: +1 205 556 1482 Email to: jon.miller@nucor.com
Web http://www.nucor.com
Materials Quality Scheme approved - MQS048
Certificate No. MD00/3323/0005/1 Expiry date: 04/08/2018
REPUBLIC STEEL
Chicago
Steelmaking
Semi-Finished
E.A.F./Ingot/Con Cast
Ingots (tonnes)
Blooms
Billets
As below
carbon, carbon-manganese, alloy
carbon, carbon-manganese
carbon, carbon-manganese
14
330
178
HOT ROLLED BAR DIVISION
CANTON WORKS
2633 Eighth Street N.E.
Canton
Ohio 44704-2311
Tel: +1 330 438 5543 Fax: +1 330 438 5552 Email to: DWalvoord@RepublicSteel.com Web: http://www.republicsteel.com
Ingots as semi finished products, nominal 740mm diameter x 4800mm, are approved for further processing for forgings to the maximum un-cropped weight
shown above.
Certificate #: MD00/2236/0006/1 Expiry date: 14/05/2016
SSAB ALABAMA, INC.
New Orleans
Steelmaking
Plates
E.A.F. / Con Cast
Normal Strength
Higher Strength
Boiler & Pressure Vessel
As below
D
A, B
AH27S, AH32, AH36, DH32, DH36
360FG, 410FG, 460FG, 490FG, 510FG
35
50
38
38
12400 Highway 43 North
Axis
Alabama 36050
Tel: + 01 256-546-2669 Fax: +01 256-546-2670 email mailto:lbridges@ipsco.com Web http://www.ipsco.com
Materials Quality Scheme Approved - MQS 042
Certificate No. MD00/3108/0007/1 Expiry date: 30/03/2017
STEEL DYNAMICS INC
Cleveland
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Rolled Bars
carbon, carbon-manganese, alloy
Carbon, Carbon manganese, Alloy
Steelmaking
Sections
E.A.F. / Con Cast
Normal Strength
Higher Strength
As below
A, B, D
AH32, AH36
Steelmaking
Semi-Finished
E.A.F./Ingot/Con Cast
Bars
As below
carbon, carbon-manganese, alloy
178
ENGINEERED BAR PRODUCTS DIVISION
8000 North County Road 225 East,
Pittsboro,
IN, 46167
Tel: +1 317 892 7179 Fax: +1 317 892 7005
E-mail: Thad.edwards@steeldynamics.com
Certificate No: MD00/4134/0002/1 Expiry Date: 23/03/2019
Concast blooms approved to 262 x 358 mm section.
STEEL OF WEST VIRGINIA, INC.
Philadelphia
12
12
17th Street and 2nd Avenue,
Huntington,
WV 25703
Tel: 800-828-6849 Fax: +1 304-697-5842 Mob: +1 304-638-7981
email: jsimmons@swvainc.com web: swvainc.com
Cert No: MD00/4547/0001/1 Expiry Date: 31/01/2019
Approved for bulb flats.
TIMKEN STEEL CORPORATION
Chicago
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
85
330
As at 06 September 2016
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
Name and Address
LR Office
Product
Category
Grade
Max Thickness/Diameter (mm)
Steelmaking
Semi-Finished
E.A.F. / Con Cast
Bars
As below
carbon, carbon-manganese, alloy
Faircrest Steel Plant
1835 Dueber Avenue S.W.
Canton
OH 44706-0932
Tel: +1 330 471 3263 Fax: +1 330 471 4077
Email: robert.w.hoff@timken.com Werb: http://www.timken.com
Certificate No. MD00/1510/0006/1 Expiry date: 10/01/2017
TIMKEN STEEL CORPORATION
Chicago
330
Harrison Steel Plant
1835 Dueber Avenue S.W.
Canton
OH 44706-0932
Tel: +1 330 471 3263 Fax: +1 330 471 4077
Email: robert.w.hoff@timken.com Werb: http://www.timken.com
Certificate No. MD00/4284/0003/1 Expiry date: 10/01/2017
Page
© Lloyd’s Register Group Limited 2016. All rights reserved.
86
As at 06 September 2016
Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective
officers, employees or agents are, individually and collectively, referred to in this
clause as ‘Lloyd's Register’. Lloyd's Register assumes no responsibility and shall
not be liable to any person for any loss, damage or expense caused by reliance on
the information or advice in this document or howsoever provided, unless that
person has signed a contract with the relevant Lloyd's Register entity for the
provision of this information or advice and in that case any responsibility or liability
is exclusively on the terms and conditions set out in that contract.
© Lloyd’s Register Group Limited 2016. All rights reserved.
© Lloyd’s Register Group Limited 2016. All rights reserved.
Related documents
One, no one, and one hundred thousand
One, no one, and one hundred thousand
Download