Catalog
Number
Notes
FEATURES & SPECIFICATIONS
Type
INTENDED USE — Architectural deep-cast luminaire provides general illumination for rough service (vandalresistant) applications. Ideal for interior or exterior applications where safety and security are a concern. Designed to complement building architecture and to endure extreme environmental conditions and physical
abuse. Certain airborne contaminants can diminish integrity of acrylic. Click here for Acrylic Environmental Compatibility table for suitable uses.
CONSTRUCTION — Bezel one-piece, marine-grade die-cast aluminum, low copper alloy (<1% copper),
.125" (1/8") thick. Encloses lens and secures to housing with stainless steel Torx® T-10 set screws (see Options).
Housing: One-piece, marine-grade die-cast aluminum, low copper alloy (<1% copper), with post-painted
polyester powder coat finish. Four-hole mounting detail for use directly over outlet box, or conduit entry
through three 1/2" threaded openings on side or 3/4" threaded opening on rear surface.
Gasket: Polycarbonate: Perimeter lens gasket is one-piece silicone "O" ring. Glass: Perimeter lens gasket is
closed-cell silicone. Pad mounting is closed-cell neoprene that seals housing to mounting surface. Gaskets
help cushion impact shock.
Finish: Standard finish is textured polyester powder coat in white, black or bronze. Optional architectural
colors are available (see Options).
OPTICS — Lens-polycarbonate: Translucent white, injection-molded, UV-stabilized lens is .125" (1/8") thick.
Smooth exterior allows for easy cleaning, and interior pattern diffuses light for even surface illumination.
Lens-glass: Tempered borosilicate lens, .250" (1/4") thick, has smooth exterior for easy cleaning and textured interior.
Reflector: Internal reflector is semi-specular aluminum, with high-reactance white powder coat perimeter for
maximum light output. Lamp positioning assures uniform brightness and illumination.
ELECTRICAL — Ballast: Class P, electronic, high power factor, multi-volt with starting temperature of
-5°F (-20°C).
Socket: High-temperature thermoplastic lamp with retention clip.
Lamp: 35K lamp(s) included unless specified L/LP.
INSTALLATION — Unit may be ceiling- or wall-mounted..
LISTINGS — UL Listed to U.S. and Canadian safety standards (see Options). UL listed for 25°C ambient temperatures and wet locations. IP65 rated.
WARRANTY — 1-year limited warranty. Complete warranty terms located at
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Actual performance may differ as a result of end-user environment and application.
All dimensions are shown in inches (centimeters) unless otherwise specified.
Note: Specifications subject to change without notice.
ORDERING INFORMATION
Rough Service Fixture
VGR2C
COMPACT FLUORESCENT
Round Eyelid
Deep Housing
Wall Mounted
6-7/8
(17.5)
13-3/4
(34.9)
Example: VGR2C 2/26TRT MVOLT DWHG TRS LPI
For shortest lead times, configure products using standard options (shown in bold).
VGR2C
Series
VGR2C
Wattage
13DTT
2/13DTT
18DTT
2/18DTT
26DTT
2/26DTT
26TRT
2/26TRT
32TRT
2/32TRT
42TRT
2/42TRT
Lens
One 13W double twin-tube lamp
Two 13W double twin-tube
lamps
One 18W double twin-tube lamp
Two 18W double twin-tube
lamps
One 26W double twin-tube lamp
Two 26W double twin-tube
lamps
One 26W triple-tube lamp
Two 26W triple-tube lamps
One 32W triple-tube lamp
Two 32W triple-tube lamps
One 42W triple-tube lamp
Two 42W triple-tube lamps
(blank) Polycarbonate
GL
Borosilicate
glass
Voltage
120
277
347
MVOLT1
Accessories: Order as separate catalog number.
RK1 T10DRV
RK1 T20BIT
RK1 T20DRV
VGRDS XXX
INDUSTRIAL
Torx TX10 screwdriver, for use with Gateway set screws.
Hex-base driver bit, Torx TX20, for tamper-resistant screws with center reject pin.
Torx TX20 screwdriver for use with tamper-resistant screws with center reject pin.
Decorative shroud16
Paint finishes2
Standard textured
finishes
DWHG White
DBLB Black
DDBT Dark bronze
DNAT Natural
aluminum
DSST Sandstone
Optional textured
finishes
DBNH Bronze
DSPD Dark gray
DSPE Green
DSPF Rust
DSPG Dark red
DSPH Light red
DSPJ Light gray
Options
Lamp15
Shipped installed in fixture
ADEZ Advance Mark X electronic dimming ballast3
ECOS EcoSystem electronic dimming ballast4
DS
Dual switching
EC
Emergency circuit (Incandecsent - 25W
max., DC bayonet base)5
ELDW Emergency lighting6,7,8,9
GLR
Internal fast-blowing fusing9
GMF Internal slow-blowing fusing9
NL
Night-light (Incandescent - 6W max., 626
DC base)5,10,11
PE
Photoelectric cell12
TRS
Tamper-resistant screws13
VGRDS Decorative shroud14
CSA
Listed and labeled to comply with Canadian
safety standards
Notes
1 Multi-volt electronic ballast (for DTT and TRT lamps) capable of
operating on any line voltage between 120 and 277 volt.
2See www.lithonia.com/archcolors for additional color options.
3 Available with 26DTT and all single TRT lamps.
4 Available with 18DTT, 26DTT and all TRT lamps.
5 Maximum wattage lamp provided.
6 42TRT maximum voltage.
7 Not available with CSA certification.
8 Minimum operating temperature is 32°F (0°C).
9
10
11
12
13
14
15
16
LPI
Lamp(s)
included
(standard)
L/LP Less
lamp(s)
Must specify voltage; 120 or 277 volts only.
Option available for single lamp units only.
120V only.
Must specify voltage. Not available MVOLT.
T-20 screws with center reject pin.
Color will be the same as the bezel.
Lamp(s) included unless L/LP is specified.
Must specify color (Example: VGRDS DWHG).
VGR2CF
VGR2C Rough Service Wall-Mounted Fixture, Compact Fluorescent
VGR2C 2/32TRT 120 (WALL),
CF32DT/E/IN/835 lamp, 1.4 s/mh, 2400 rated lumens, test no. LTL7712
Distribution data
180° 165° 150° 135°
Angle
120°
105°
95°
90°
85°
75°
200
400
600
60°
0° 15° 30°
45°
Spacing criterion: 1.4
Spacing to mounting height: 1.4
0°
5°
15°
25°
35°
45°
55°
65°
75°
85°
90°
95°
105°
115°
125°
135°
145°
155°
165°
175°
180°
cp.
Output data
Lumens
Zone
0
7
23
46
73
103
129
149
160
159
0
148
127
101
73
46
23
8
1
0
0
0°- 30°
0°- 40°
0°- 60°
0°- 90°
90°- 180°
0°- 180°
72
72
82
99
117
133
144
151
151
146
142
136
120
102
81
59
37
18
5
0
0
Lumens
%lamp
76 1.6
150
3.1
382
8.0
850 17.7
529 11.0
1379 *28.7
A
B
C
D
* Fixture efficiency
VGR2C 2/32TRTWALL
VGR2C 2/32 TRT WALL MOUNT (in feet)
HORIZONTAL PLANE ISOCANDLE LINE
(8 FT. SHOWN)
7
A
2.6
B1.3
C.65
D.32
8
2.0
1.0
.50
.25
910
1.61.3
.80 .65
.40 .32
.20 .16
Tested to current IES and NEMA standards under stabilized laboratory conditions.
Various operating factors can cause differences between laboratory data and actual
field measurements. Dimensions and specifications on this sheet are based on the
most current available data and are subject to change without notice.
INDUSTRIAL:
One Lithonia Way Conyers, GA 30012
Phone: 800-315-4963 Fax: 770-981-8191
VGR2CF
www.lithonia.com
© 2000-2012 Acuity Brands Lighting, Inc.
All rights reserved. Rev. 02/16/12