Wiper motor | W12
Mounting Instructions
Before installation please read these instructions.
»» 2 Speed, self-parking
»» Heavy Duty motor, 12Nm
»» Wipershaft in stainless steel
»» Various sweep angle: 45 - 110°
»» CE approved; EMC protected
»» Spray proof IP65
»» Insulated ground for metal, plastic and wooden boats.
»» Powers up to 610 mm x 560 mm /24˝ x 22˝ arm/blade
combinations.
info@rocamarine.com | rocamarine.com
Mounting instructions - Wiper motor | W12
Keep battery main switch turned off during operation inside of the wiper motor
1.
Remove cover with enclosed torx key.
2.
Locate the mounting position .Drill mounting holes (template provided on the box).
Mount motor to the surface. See picture 1.
3.
The motor is pre-set to 45° sweep and right parking position. To set the arm in correct position do as following:
a. Find the centerline of the desired sweep area.
b. Attach the wiper arm 22.5° from the centerline (use the attached template below). See picture 2 and 3.
4.
Loosen the two screws on the angle plate with the enclosed torx key. See picture 5. Move the arm to desired end position of
sweep area. See picture 4. Tighten the two screws firmly.
5.
To set the self-parking feature to park in the left position use the enclosed torx key and turn the parking selector clockwise See
picture 5.
6.
Connect wires as shown in picture 6.
If using Roca switch 466099/466208 use 6a. For all other switches use 6b.
Use a 5Amp fuse for 12V and 3Amp for 24V.
7.
Make sure the gasket is in right position and replace the cover on the motor with the screws taken out.
Note:
If the arm sweeps too far out on both sides, the sweep angle needs to be reduced, repeat
point 5 above. If the arm goes too far on one side only then you did not start with the arm in
center of the sweep. Remove the arm and place it at the correct position.
1
Alternative fastening
5 / 0.2"
16 - 17
0.67"
C - C 145
5.71"
22.5°
2
m
r ar
e
Wip
Centerline for sweep area
Instruction sheet
3c
rea
22.5°
pa
22
nte
rlin
ef
or
sw
ee
.5°
Ce
3b
22.5°
Centerline for sweep area
Centerline for sweep area
3a
Instruction sheet
Instruction sheet
5
4
End
position
Parking selector
Loosen
torx screws
Angle plate
Fuse
5A/12V
3A/24V
Fuse
S
P
+
5A/12V
3A/24V
Switch circuit
Rocker switch - 466099
Actuator - 466026
F
Battery
G
Right park pos
CCW
6a
+
Battery
F S
P = Parking
S = Slow
F = Fast
G = Ground
P
G
6b
13,8
0.54"
5
0.2"
Ø 13,8 / 0.54"
100
3.9"
L1
C-C 145
5.71"
170
6.69"
VARIATIONS:
L2
2.32"
Limited warranty
HR
E E YE A
3
RS
»» Roca warrants the wiper motors to be free from defective
material and workmanship for a period of 3 years from the
date of purchase.
»» This warranty does not apply to failure or damage caused
ARstrike or damby improper installation, misuse, lightning
RENTY
age from a power surge.
W
Max length:
Voltage input:
L1L212V
24V
16 / 0.63” 38 / 1.5”
533011
533012
41 / 1.61” 64 / 2.5”
533021
533022
66 / 2.6”
90 / 3.5”
533031
533032
59
T
17
0.67"
Std.splines z=72
27
1.06"
M16x1
»» If failure occurs during this period, return it to your dealer
for repair or replacement.
OPTIONAL:
Wiper arm, Wiper blade, Control box, Spray system
Adjustable windshield arms
Coated stainless steel with UV-protection.
Wiper blade
Wiper blade Black powder coated – Natural rubber.
280 mm / 11”
430 mm / 17”
305 mm / 12”
455 mm / 18”
330 mm / 13”
480 mm / 19”
355 mm / 14”
508 mm / 20”
380 mm / 15”
533 mm / 21”
405 mm / 16”
560 mm / 22”
3 Way toggle switch
with or without
LED backlight.
Wiper arm adjustable. Hook-type connection.
310–440 mm / 12”–17”
480–610 mm / 19”–24”
Roca wiper control
for synchronized, two speed and intermittent drive of up to 3 motors.
Wiper arm adjustable TIP 40° R/L. Hook-type connection.
340–470 mm / 13.5”–18.5”
480–610 mm / 19”–24”
Pantograph arm adjustable. Hook-type connection.
340–470 mm / 13.5”–18.5”
480–610 mm / 19”–24”
Washer systems
For more info: www.rocamarine.com
533145_Inst_5330xx | 2010-09-20 RE/LW/MB