TVS Diode Arrays (SPA®® Diodes)
General Purpose ESD Protection - SP1020 Series
SP1020 Series 20pF 30kV Bidirectional Discrete TVS
RoHS
Pb GREEN
Description
The SP1020 includes back-to-back Zener diodes fabricated
in a proprietary silicon avalanche technology to provide
protection for electronic equipment that may experience
destructive electrostatic discharges (ESD). These robust
diodes can safely absorb repetitive ESD strikes above the
maximum level specified in the IEC61000-4-2 international
standard (Level 4, ±8kV contact discharge) without
performance degradation. The back-to-back configuration
provides symmetrical ESD protection for data lines when
AC signals are present.
Pinout
Features
0201 Flipchip
1
2
Note: Drawing not to scale
Functional Block Diagram
1
• ESD, IEC61000-4-2,
±30kV contact, ±30kV air
• Low capacitance of 20pF
(@ VR=0V)
• EFT, IEC61000-4-4, 40A
(5/50ns)
• Low leakage current of
0.1μA at 5V
• Lightning, IEC61000-4-5,
5A (tP=8/20μs)
• Industries smallest ESD
footprint available (01005)
Applications
2
• Mobile Phones
• Wearable Technology
• Smart Phones
• Camcorders
• Portable Navigation
Devices
• Portable Medical
• Tablets
• Digital Cameras
• Point of Sale Terminals
Life Support Note:
Not Intended for Use in Life Support or Life Saving Applications
The products shown herein are not designed for use in life sustaining or life saving
applications unless otherwise expressly indicated.
©2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 02/17/15
SP1020 Series
1
557
TVS Diode Arrays (SPA®® Diodes)
General Purpose ESD Protection - SP1020 Series
Absolute Maximum Ratings
Symbol
Parameter
Value
5.0
Units
IPP
Peak Current (tp=8/20μs)
TOP
Operating Temperature
-40 to 125
°C
A
TSTOR
Storage Temperature
-55 to 150
°C
1
Notes:
1. CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Thermal Information
Parameter
Storage Temperature Range
Rating
Units
-55 to 150
°C
Maximum Junction Temperature
150
°C
Maximum Lead Temperature (Soldering 20-40s)
260
°C
Electrical Characteristics (TOP=25ºC)
Parameter
Symbol
Reverse Standoff Voltage
VRWM
Leakage Current
ILEAK
Clamp Voltage1
Test Conditions
RDYN
ESD Withstand Voltage1
VESD
Diode Capacitance
Max
Units
6.0
V
10
nA
0.5
μA
VR=5V with 1 pin at GND
0.1
IPP=1A, tp=8/20µs, Fwd
9.3
V
IPP=2A, tp=8/20µs, Fwd
10.0
V
TLP, tP=100ns, I/O to GND
0.32
Ω
IEC61000-4-2 (Contact Discharge)
±30
kV
IEC61000-4-2 (Air Discharge)
±30
kV
CD
1
Typ
VR=3.3V with 1 pin at GND1
VC
Dynamic Resistance2
Min
Reverse Bias=0V
20
pF
Note:
1 Parameter is guaranteed by design and/or device characterization.
2 Transmission Line Pulse (TLP) with 100ns width and 200ps rise time.
Pulse Waveform
Capacitance vs. Reverse Bias
25
110%
100%
20
90%
70%
Capacitance (pF)
Percent of IPP
80%
60%
50%
40%
30%
20%
15
10
5
10%
0%
0
0.0
5.0
10.0
15.0
20.0
25.0
30.0
0
Time (μs)
©2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 02/16/15
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
Bias Voltage (V)
SP1020 Series
2
558
TVS Diode Arrays (SPA®® Diodes)
General Purpose ESD Protection - SP1020 Series
Clamping Voltage vs IPP
Transmission Line Pulsing (TLP) Plot
20
14.0
18
TLP Current (A)
Clamp Voltage (VC)
12.0
10.0
8.0
6.0
16
14
12
10
8
6
4.0
4
2.0
2
0.0
0
1.0
2.0
3.0
4.0
0
5.0
5
10
15
20
TLP Voltage (V)
Peak Pulse Current -I PP (A)
Soldering Parameters
Pre Heat
Pb – Free assembly
- Temperature Min (Ts(min))
150°C
- Temperature Max (Ts(max))
200°C
- Time (min to max) (ts)
60 – 180 secs
Average ramp up rate (Liquidus) Temp (TL)
to peak
3°C/second max
TS(max) to TL - Ramp-up Rate
3°C/second max
Reflow
- Temperature (TL) (Liquidus)
217°C
- Temperature (tL)
60 – 150 seconds
260
Time within 5°C of actual peak
Temperature (tp)
20 – 40 seconds
Ramp-down Rate
6°C/second max
Time 25°C to peak Temperature (TP)
8 minutes Max.
Do not exceed
260°C
Critical Zone
TL to TP
Ramp-up
TL
TS(max)
tL
Ramp-do
Ramp-down
Preheat
TS(min)
tS
25
Peak Temperature (TP)
+0/-5
tP
TP
Temperature
Reflow Condition
time to peak temperature
Time
°C
Part Marking System
Part Numbering System
SP 1020 – 01 W T G
TVS Diode Arrays
(SPA® Diodes)
G= Green
T= Tape & Reel
Series
Number of
Channels
Package
W: 01005 Flipchip
Ordering Information
©2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 02/16/15
Part Number
Package
Marking
Min. Order Qty.
SP1020-01WTG
01005 Flipchip
• •
15000
SP1020 Series
3
559
TVS Diode Arrays (SPA®® Diodes)
General Purpose ESD Protection - SP1020 Series
Package Dimensions — 01005 Flipchip
BOTTOM VIEW
0.24
0.34
0.55
0.21
TOP VIEW
0.19
0.20
0.16
Stencil opening
Recommended Solder Pad Footprint
and Stencil opening
0.24
01005
Flipchip
Symbol
0.21
*Sizes in mm
Min
Typ
Max
Min
Typ
Max
0.181
0.209
0.0060
0.0071
0.0082
0.008
0.011
0.0143
0.0003
0.0004
0.19
0.0006
0.170
0.1950.20
0.0057
0.0067
0.0077
0.205
0.230
0.255
0.415
0.440
0.465
A2
0.145
D
E
0.34
A1
Thickness of Stencil opening is 0.08mm
Inches
0.153
0.55
A
Millimeters
Stencil opening
0.00810.16
0.0091
0.0163
Solder Pad
0.0173
0.0100
0.0183
Solder Pad
Embossed Carrier Tape & Reel Specification — 01005 Flipchip
Recommended Solder Pad Footprint
and Stencil opening
Thickness of Stencil opening is 0.08mm
*Sizes in mm
©2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 02/16/15
4
560
Symbol
Millimeters
A0
0.30+/-0.03
B0
0.51+/-0.03
K0
0.20 + 0.03
F
3.50 +/- 0.05
P1
2.00+/-0.10
W
8.00+/-0.10
SP1020 Series