D ATA S H E E T
Facility Site Alarm
C r o ss C o n n ect C a b i n et
Features
Overview
ƒƒ Steel cabinet with gray powder coated finish
Typical site alarm list
ƒƒ TVSS fail
ƒƒ Commercial power fail
ƒƒ ATS on commercial power
ƒƒ ATS on generator power
ƒƒ Generator not in automatic start mode
ƒƒ DC plant major alarm
ƒƒ DC plant minor alarm
ƒƒ Hinged access door with captive threaded fasteners
ƒƒ Conduit knock-out top and bottom for convienient cable routing conductor access
ƒƒ Integrated cabinet ground studs for two-hole lug landing for cabinet ground
ƒƒ Internal backing plate with Telecom 66 block IDC connectors for termination of incoming
site alarm Category 3 conductors from site device relay dry contact status alarms
ƒƒ Cross connect section allows customer alarm selections to be actively monitored by site
monitoring modem devices
ƒƒ DC plant battery off-line or thermal runaway alarm
ƒƒ Integrated Category 5 100MBS 8 port switch for Ethernet aggregation from site devices
with Ethernet webserver and SNMP alarm monitoring
ƒƒ UPS summary alarm
ƒƒ Integral 120VAC, 15A electrical convenience outlet for switch power
ƒƒ UPS low battery warning
ƒƒ Front door mounted monitor panel for summary alarm monitoring
ƒƒ Distribution fuse fail/breaker trip alarm
ƒƒ UPS in static bypass mode
ƒƒ Main service circuit breaker trip alarm/shunt trip
ƒƒ Generator low fuel
ƒƒ Generator summary alarm
ƒƒ Fire suppression system alert
ƒƒ Fire suppression system discharge
ƒƒ Fire suppression system trouble/abort
ƒƒ Intrusion alarm
ƒƒ Technician on-site (TOS switch)
ūū Includes 24 inputs to provide relay isolation and summary alarm contact selection
ūū Any facility alarm condition can be programmed to drive summary alarm contacts
and indicator to alert local staff to alarm conditions
gENERAL Specifications
Part #
dESCRIPTION
016-989-10
ƒƒ Dimensions: 26.5” high x 18.5” wide x 9.5” deep
ƒƒ Front door swings from left to right
ƒƒ Conduit access panels on top and bottom of cabinet
ƒƒ Site high temperature alarm
ƒƒ Site low temperature alarm
ƒƒ HVAC summary fail alarm (all units common alarm)
ƒƒ Ground fault detection alarm (MGB sensor)
About Comm/net Systems
Comm/net Systems, Inc. (CSI) is the leader in high power density
communications power systems. Comm/net offers comprehensive
power and communications site systems integration and deployment
services via a national footprint of regional branch offices. Additional
information can be found at www.commnetsystems.com.
Corporate Headquarters
Comm/net Systems, Inc.
4237 – 24th Avenue West
Seattle, WA 98199
24/7 Sales & Service
To purchase Comm/net Systems solutions, contact your
Comm/net Systems representative at: (800) 274-0544
or e-mail: sales@commnetsystems.com
Tel: 206.282.8670
Fax: 206.282.8684
Order Information
Shipping box is packaged for UPS or FedEx shipment
and includes an instruction manual and accessories.
www.commnetsystems.com
© 2010 Comm/net Systems, Inc. All rights reserved. Comm/net Systems, and the Comm/net Systems logo are registered trademarks of Comm/net Systems, Inc. in the United States and other countries. All other
trademarks, service marks, registered marks, or registered service marks are the property of their respective owners. Comm/net Systems assumes no responsibility for any inaccuracies in this document. Comm/net
Systems reserves the right to change, modify, transfer, or otherwise revise this publication without notice. document number 048-690-00, Revision 1, Published August 2010