Installation Instructions
Models CC-5 / CC-2
System Cardcage CC-5 (500-633037 / S24235-B123-A1)
System Cardcage CC-2 (500-633440 / S24235-B122-A1)
INTRODUCTION
The SIEMENS Model CC-5 Cardcage (see Figure 1) has five card slot
s and fits in two
positions on the Mounting Plate. The SIEMENS Model CC-2 Cardcage (see Figure
2) has two card slot s and fits in one position on the Mounting Plate. The CC-5 and
CC-2 are used for mounting all system circuit card assemblies. They each have two
removable terminal block connectors at the top and one removable terminal block
connector at the bottom of each card slot. All field-wiring connections are made
directly to the top of the cardcage while internal power is connected to the bottom
of the cardcage. The two removable terminal block connectors at the top of each slot
are arranged in two rows. The lower row is labeled 1 through 8 and the upper row is
labeled 9 through 16. These removable terminal block connectors are used for
connecting power limited external equipment. The removable terminal block connector located at the bottom of each slot is labeled 17 through 24 and is used for
connecting internal power.
UPPER ROW
(9-16)
UPPER ROW
(9-16)
LOWER ROW
(1-8)
LOWER ROW
(1-8)
Note:
Boards shown without card guides installed.
Figure 1
CC-5 Card Cage
OPERATION
P/N 315-033035-3
A24205-A334-B815
Figure 2
CC-2 Card Cage
The CC-5 and CC-2 provide a central point for mounting circuit card assemblies. If a
card requires power, it is applied through the removable terminal block at the bottom
of the cardcage. All external devices for the card are connected to the card through
the two removable terminal blocks at the top of the cardcage. The circuit card assemblies are connected to the HNET and CAN bus through the connectors on the
cardcage.
Siemens Building Technologies
Fire Safety
PRE-INSTALLATION
The CC-5 and CC-2 are shipped with the card guides removed. The card guides are
keyed to assist in installation. They can be installed either before or after the cardcage
is installed in the enclosure. For ease of installation, the card guides have been
designed to be installed after the field wiring has been completed.
Card Guide Installation
(Figure 3)
The upper and lower card guides are keyed differently and are not interchangeable.
Ensure that the card guide keys fit easily into the holes in the motherboard to
prevent damage.
1.
The upper card guide has a label on each slot that can be used to identify
the module installed in the slot. If desired, complete the label before
inserting the upper card guide.
2.
Insert the upper card guide and secure with the captive screws.
3.
Insert the lower card guide and secure with the captive screws.
UPPER CARD GUIDE
LABELS
GUIDE
PIN
LOWER CARD GUIDE
CAPTIVE SCREWS
GUIDE PIN HOLE
CAPTIVE SCREW RETAINERS
Figure 3
Card Guide Installation (CC-5 Shown)
INSTALLATION
Disconnect BATTERY and AC prior to working on equipment.
The CC-5 and CC-2 mount on the Mounting Plate. The Mounting Plate may be
located either “IN” or “OUT” of the enclosure to perform this inst allation procedure.
If the Mounting Plate is located “IN” the enclosure you will have to gain access to it
Siemens Building Technologies
Fire Safety
2
P/N 315-033035-3
A24205-A334-B815
by opening the enclosure Inner and Outer doors. If the Mounting Plate is located
outside of the enclosure, place it in front of you so that the word “T OP” is at the top
and away from you.
Each Mounting Plate can hold a maximum of two CC-5 cardcages. There are three
possible locations for mounting the CC-5 on the Mounting Plate.
1.
Flush left on the Mounting Plate in positions 1-2.
2.
In the center of the Mounting Plate in positions 2-3.
3.
Flush right on the Mounting Plate in positions 3-4.
The CC-2 is most effectively used to add two more card slots in a row that already
has one CC-5 and another 1-position module (i.e., PSC-12). It is best inst
alled in a
position adjacent to the CC-5.
In all of the possible mounting locations, the top and bottom of the CC-5 and CC-2
will be flush with the top and bottom of the Mounting Plate.
When only one CC-5 cardcage is to be installed, it is normally installed on the left
side of the Mounting Plate. There is a top and bottom to the Mounting Plate. The top
is where the word “T OP” is stamped on the Mounting Plate. When the cardcage is
mounted correctly on the Mounting Plate it will be flush on the top, bottom, and lef t
with the Mounting Plate and the two screw holes in the center of the cardcage
motherboard will be over threaded post s.
Siemens Building Technologies
Fire Safety
1.
Install four 10-32 scr ews (M5) in the threaded post s at the top lef t of
Position 1, top right of Position 2, bottom lef t of Position 1, and the bottom
right of Position 2 on the Mounting Plate. Screw each of the 10-32 screws
(M5) into the threaded post s 5-6 turns. (Refer to Figure 3.)
2.
Place the cardcage over the four screws on the Mounting Plate and slide it
down or towards you to rest on the four screws. (Refer to Figure 4.) When
the cardcage is in the correct position it will be flush with the top, bottom,
and left side of the Mounting Plate.
3.
Install the two 10-32 screws (M5) in the center of the cardcage
motherboard near the left and right edge.
4.
Tighten the six screws.
3
P/N 315-033035-3
A24205-A334-B815
Figure 4
Location Of The CC-5 and CC-2 On The Mounting Plate
Figure 5
Mounting The CC-5 and CC-2 On Mounting Plate
Siemens Building Technologies
Fire Safety
4
P/N 315-033035-3
A24205-A334-B815
WIRING
To Connect External Wiring
To The Card Slots:
At the top and bottom of the CC-5 and CC-2 and adjacent to each card slot are
removable terminal blocks. The removable terminal blocks are color-coded to each
slot and have a white cover over the top. The wiring to the two terminal block
connectors at the top of the CC-5 and CC-2 is power limited. The wiring to the
terminal block connector at the bottom of the CC-5 and CC-2 is non-power limited.
(Figure 6)
1.
On the removable terminal block, open the white cover .
2.
Insert the wire to be connected in the desired opening in the side of the
removable terminal block.
3.
Tighten the appropriate locking screw.
WHITE COVER
LOCKING SCREWS
1
2
3
4
5
6
7
8
REMOVABLE
TERMINAL
BLOCK
OPENING IN
SIDE FOR WIRE
CONNECTION
Figure 6
Removable Terminal Block On The CC-5 and CC-2
To Connect The
Data Bus:
The Data bus connectors on the cardcage motherboard are P1 and P2. (Refer to
Figure 7.) They are 60 pin, keyed, male connectors with connector extractors.
1.
Open the connector ejectors out of the vertical position and away from the
connector body.
2.
Insert the female cable connector into the male connector (P1 or P2) on the
cardcage motherboard. Gently press the cable connector into the
motherboard connector. As the cable connector is pressed in, the
connector ejectors will begin to move to the vertical position. When the
cable connector is fully seated the connector ejectors will be vertical.
Use the 60 pin bus cable - long, P/N 500-633997 / C24235-A1-K9 when the PSC-12C/
PSX-12C is located on a different Mounting Plate
Siemens Building Technologies
Fire Safety
5
P/N 315-033035-3
A24205-A334-B815
To Connect The CAN Bus:
The CAN bus (P3) is a six pin connector located just above P1 on the cardcage
motherboard. (Refer to Figure 7.) It is used to supply CAN communications and
power to the Switch Control Modules (SCM-8S), LED, Fan Control Modules
(FCM-6S), Live Voice Microphone Module (LVM) and Firefighters Master Telephone
(FMT). The connector is keyed and requires no special instructions for cable
connection. Use cable CCL, P/N 500-634214 / C24235-A1-K6 to connect from CAN
bus (P3) on CC-5 and CC-2 to the desired module. CAN power must be supplied to
E11 (CC-5) or E5 (CC-2) Refer to Figure 8 for wiring det ails.
E5
E4
(GR
EEN
E)
(BLU
)
J5
)
W
LLO
(YE
E3
E2
(OR
AN
GE
J4
)
P2
J3
)
E1
CONNECTOR EJECTORS
IN VERTICAL POSITION
J10
J2
(RED
-5
P4
P3
J9
CC
J1
J8
J7
P1
17
J6
17
60
17
17
17
18
19
20
21
22
23
24
18
19
20
21
22
23
24
18
19
20
21
22
23
24
18
19
20
21
22
23
24
18
19
20
21
22
23
24
T5
SLO
T4
SLO
T3
SLO
T2
SLO
T1
SLO
Figure 7
Location Of Connectors (CC-5 Shown)
Figure 8
Connecting Power For CAN Bus
Siemens Building Technologies
Fire Safety
6
P/N 315-033035-3
A24205-A334-B815
SPECIFICATIONS
Physical Specifications: CC-5 10.58”W x 14.25” H (26.87cm x 36.20cm)
CC-2 4.78”W x 14.25”H (12.14cm x 36.20cm)
Electrical Ratings:
Data
CC-2. The
given
The PSC-12C supplies the power to the two 60-pin
bus connectors (P1 and P2) in the CC-5 and
total rating on P1 and P2 for all CC-5s in any
enclosure is as follows:
24 VDC, 2 Amps max
6.2 VDC, 2 Amps max
See PSC-12C Installation Instructions, P/N 315-033060 / A24205-A334-B819 and the
PSX-12C Installation Instructions, P/N 315-034050 / A24205-A334-B818, for
complete power supply loading calculations.
Siemens Building Technologies
Fire Safety
7
P/N 315-033035-3
A24205-A334-B815
For CE applications in Cerberus E100 systems refer to
Installation Instruction A24205-A334-B844 (English) orA24205-A334-A844 (German).
Siemens Building Technologies, Inc. Siemens Building Technologies, Ltd. Siemens AG
8 Fernwood Road
2 Kenview Boulevard
I BT DE FS SYS
Florham Park, New Jersey 07932
Brampton, Ontario L6T 5E4 CN
D-81379 München
P/N 315-033035-3
A24205-A334-B815