PRODUCT OVERVIEW IP710-DLZ 0 - 10 Volt Dimming Control Interface 1 3 9 3 S o u t h S a n ta F e D r , D e n v e r , C O 8 0 2 2 3 • 1 - 8 8 8 - 8 8 7 - 2 9 8 0 • i n f o @ e v o - l i t e . c o m • w w w . e v o - l i t e . c o m 1 PRODUCT SPECIFICATIONS IllumaTech Preset Slide & Rotary Controls IPL06-10 RTD01-10 APPLICATIONS To simplify inventory, IllumaTech® Slide and Rotary Controls are designed for both single pole (one location) and 3-way (two location) applications. IllumaTech Preset Slide Controls feature a smooth, captured slide bar for fine adjustment of lighting levels and an easy to use push button that provides preset ON/OFF switching. Color change kits simplify inventory by diminishing the need for stocking separate devices in every color. Additionally, the IPL06 features a future-proof dimming platform that is compatible with incandescent and dimmable LED and CFL lamps. IllumaTech slide controls include LED, CFL, magnetic low voltage, electronic low voltage and fluorescent lighting dimmers, as well as full range and quiet fan speed controls. IllumaTech Rotary Controls combine the ease of a traditional rotary knob with the contemporary look of Decora®. They are perfect for specifiers, lighting designers and engineers who require reliable performance and a modern rotary look. Rotary controls include push on/push off dimmers in illuminated and non-illuminated versions, as well as quiet fan speed controls and a combination dimmer/ fan speed control. FEATURES AND BENEFITS n LED Illuminates when load is off (select models) n Provide single pole (one location) or 3-way (two location) lighting control when used with a 3-way switch n Attractive styling coordinates perfectly with Leviton’s complete line of Decora wiring devices n Compatible with Decora Plus™ screwless and Decora standard designer wallplates n Built-in radio/TV interference filter n Fit easily into a standard wallbox and are suitable for multi-gang installations n IllumaTech controls come packaged with six product options in each box for superior versatility; 3 changeable color faces and single pole or 3-way control RPI06-1L IllumaTech Preset Slide Controls n Fluid slide movement allows fine adjustment of light level with minimal effort n Captive wraparound slide bar remains securely attached n Compatible with dimmable LED and CFL lamps n Easy to use push button switch with green LED locator n Push button switch acts as an air gap switch completely disconnecting power from unit for bulb changing n Slide controls travel approximately 20mm n Power failure recovery ensures retention of last setting before power interruption n Quiet 1.5 amp fan speed controls are ideal for libraries, home offices, bedrooms and any area where ceiling fan noise could become distracting. Full range 5 amp fan speed controls are also available IllumaTech LED/CFL/Incandescent Dimmer n IPL06 designed specifically for dimmable LED and CFL lamps as well as incandescent n Features a built-in starting technology for CFL lamps n Wider dimming range on LED and CFL lamps than conventional incandescent dimmers n Optional programming feature allows for users to modify the dimming range to optimize low light level performance when required IllumaTech 0-10V LED/Fluorescent Dimmer n IP710-DL designed specifically for Mark-7® 0-10V fluorescent ballast n IP710-LF designed for use with LED fixtures using 0-10V power supplies n Dual voltage 120V/277V; 28 mAmps maximum sink current n No power pack required for switching IllumaTech® Preset Slide and Rotary Controls ® IllumaTech Rotary Controls n Rotary knob with contemporary styling n Quiet 1.5 amp fan speed controls are perfect for libraries, home offices, bedrooms and any area where ceiling fan noise could become distracting n Dual fan speed control and dimmer is ideal for ceiling fans with built-in light fixtures SPECIFICATIONS n Operating 0˚C – 55˚C n Non-operating 10˚C – 85˚C n Relative humidity, non-condensing 20% to 90% Leviton Mfg. Co., Inc. 201 North Service Road, Melville, NY 11747 Tech Line: 1-800-824-3005 Fax: 1-800-832-9538 www.leviton.com © 2014 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice. 1 3 9 3 S o u t h S a n ta F e D r , D e n v e r , C O 8 0 2 2 3 • 1 - 8 8 8 - 8 8 7 - 2 9 8 0 • i n f o @ e v o - l i t e . c o m • w w w . e v o - l i t e . c o m 2 (1 ( ( DIMENSIONAL DRAWINGS IllumaTech Preset Slide Controls Color Change Kit for IllumaTech Slide Controls (Preset Kit Shown) 1.73 AGENCY STANDARDS AND COMPLIANCE (44.04) (33.12) (19.05) Warning: When retrofitting Mark 10® Powerline dimming ballasts into fixtures that originally had Instant Start ballasts, the sockets MUST be replaced with Rapid Start sockets to allow proper dimmer operation and prevent property damage, injury or death. Refer to the instructions provided with the ballast and the Leviton dimmer. 4.15 (105.4) IPL06: LED and CFL lamps marked or rated as dimmable can be used with this dimmer. For a complete list of approved LED and CFL lamps visit www.leviton.com/universal 3.28 (83.3) 4.12 (104.64) 4.12 (104.64) 3.28 (83.34) 1.73 (44.04) Use Leviton Power Extenders to extend the load capacity of box mounted dimmers. Leviton Power Extenders are available for incandescent, magnetic low voltage, electronic low voltage, Mark 10® Powerline fluorescent dimming ballasts or equivalents and 0-10 VDC dimmable fluorescent ballasts such as Mark 7® 0-10V, OSRAM Sylvania Quicktronic® Helios™ or equivalent ballasts. 4.15 (105.4) 4.12 (104.64) 3.28 (83.34) INSTALLATION CONSIDERATIONS Note: Sharing a neutral wire may cause flickering. Connect all devices to the same phase or run a separate neutral to each phase. Consult Leviton Techline if problems persist. 2.23 (56.64) MED Lamp Selector/ Programming Switch n UL Listed (File #E-31373) n CSA Certified (File #LR-3413) 2.68 (68.1) HI 3.28 (83.3) 0.75 0.75 (19.05) 2.23 (56.64) MED 2.68 (68.1) 1.30 1.30 (33.12) 4.12 (104.64) HI OF F X MA Strap X MA IllumaTech Rotary Controls 1.73 (44.04) 3.28 (83.34) 2.67 (67.81) 0.75 (19.05) 1.73 (44.04) OF F IllumaTech Dual Controls 1.30 (33.12) 0.75 (19.05) ON/OFF LED 3.28 (83.34) 2.12 (53.8) 0.38 (9.7) 1.30 (33.12) 2.67 (67.81) 3.28 (83.3) 2.68 (68.1) Snaps Push in 2 Locations Slider LO 1.41 (35.8) LO IllumaTech® Preset Slide and Rotary Controls 4.15 (105.4) Frame 1.41 (35.8) (53.8) – CFL0.38 mode for dimmable CFLs. This2.12 feature (9.7) provides a higher starting voltage that is required for many Compact Fluorescent Lamps. – LED/Incandescent mode provides optimized dimming for LED lamps and for incandescent operation. – Switch also enables the programming mode allowing users to change the dimmer low light settings for applications where the user experiences unstable light or flicker. 1.41 (35.8) Leviton Mfg. Co., Inc. 2.12 (53.8) 0.38 (9.7) 201 North Service Road, Melville, NY 11747 Tech Line: 1-800-824-3005 Fax: 1-800-832-9538 www.leviton.com © 2014 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice. 1 3 9 3 S o u t h S a n ta F e D r , D e n v e r , C O 8 0 2 2 3 • 1 - 8 8 8 - 8 8 7 - 2 9 8 0 • i n f o @ e v o - l i t e . c o m • w w w . e v o - l i t e . c o m 3 Maximum Load for Multi-Gang Applications CAT. NO. SINGLE 2-GANG 3-GANG OR MORE IPI06-1L 600W 500W 400W IPI10-1L 1000W 800W 700W IPL06-10 600W Incandescent 150W LED/CFL 500W Incandescent 150W LED/CFL 400W Incandescent 150W LED/CFL IPE04-1L 400VA (320W) 350VA (280W) 250VA (200W) IPM06-1L 600VA (450W) 500VA (375W) 400VA (300W) IPM10-1L 1000VA (800W) 800VA (640W) 700VA (560W) IP710-DL 1200VA/1500VA 1200VA/1500VA 1200VA/1500VA IP710-LF 1200VA/1500VA 1200VA/1500VA 1200VA/1500VA IPX06-10 600VA 500VA 400VA IPX10-10 1000VA 800VA 700VA IPX06-70 600VA 600VA 600VA IPX12-70 1200VA 1200VA 1200VA IPF01-1L 1.5A 1.5A 1.5A IPF05-1L 5A 4.1A 3.3A RP106-IL 600W 500W 400W RPI06-10 600W 500W 400W RTF01-10 1.5A 1.5A 1.5A RTD01-10 300W/1.5A 300W/1.5A 300W/1.5A IllumaTech® Preset Slide and Rotary Controls In multi-gang applications derating may be required in accordance with the following charts. For controls with side sections fin removal may be required (consult instruction sheets for further details). WARRANTY INFORMATION n Limited Five-Year Warranty WIRING DIAGRAMS DIAGRAM 1 DIAGRAM 2 Single Pole Wiring 3-Way Wiring Dimmer Hot (Black) Line 120VAC, 60Hz Black 3-Way Switch Dimmer Red Hot (Black) Black Red Red Insulating Label Common Terminal (Black Screw) Black Red Green Ground Line 120VAC, 60Hz White Neutral (White) Green Ground Green Ground White Neutral (White) Leviton Mfg. Co., Inc. 201 North Service Road, Melville, NY 11747 Tech Line: 1-800-824-3005 Fax: 1-800-832-9538 www.leviton.com © 2014 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice. 1 3 9 3 S o u t h S a n ta F e D r , D e n v e r , C O 8 0 2 2 3 • 1 - 8 8 8 - 8 8 7 - 2 9 8 0 • i n f o @ e v o - l i t e . c o m • w w w . e v o - l i t e . c o m 4 ORDERING INFORMATION IllumaTech® Preset Slide and Rotary Controls All IllumaTech Preset and Rotary Dimmers provide single pole (one location) or 3-way (two location) control when used with a 3-way switch. DESCRIPTION CAT. NO. RATING COLOR Incandescent Dimmer with LED locator Incandescent Dimmer with LED locator IPI06-1L* 600W-120VAC Z IPI10-1L 1000W-120VAC Z LED/CFL/Incandescent Dimmer, no LED IPL06-10 600W Incandescent 150W LED & CFL 120VAC Z Magnetic Low Voltage Dimmer with LED locator IPM06-1L 600VA (450W)-120VAC Z Magnetic Low Voltage Dimmer with LED locator IPM10-1L 1000VA (800W)-120VAC Z Electronic Low Voltage Dimmer with LED locator; neutral required IPE04-1L* 400VA (320W)-120VAC Z Fluorescent Dimmer for Mark 10® Powerline Ballast, no LED locator IPX06-10 600VA-120VAC Z Fluorescent Dimmer for Mark 10® Powerline Ballast, no LED locator IPX10-10* 1000VA-120VAC Z Fluorescent Dimmer for Mark 10® Powerline Ballast, no LED locator IPX06-70 600VA-277VAC Z Fluorescent Dimmer for Mark 10® Powerline Ballast, no LED locator IPX12-70 1200VA-277VAC Z Fluorescent Dimmer for Mark 7® 0-10V Ballast with LED locator IP710-DL* 1200VA @120VAC 1500VA @ 277VAC Z LED Dimmer for 0-10V power supplies, no LED locator IP710-LFZ* 1200VA @120VAC 1500VA @ 277VAC Z IPF01-1L 1.5A-120VAC Z Quiet Fan Speed Control with LED locator (For multi-gang installation, see derating chart) Fully Variable Fan Speed Control with LED locator IPF05-1L 5A-120VAC Z Rotary Incandescent Dimmer with LED locator RPI06-1L 600W-120VAC Z Rotary Incandescent Dimmer, no LED locator RPI06-10 600W-120VAC Z Quiet Fan Speed Control, single pole only, no LED locator RTF01-10 1.5A-120VAC Z Rotary Dual Quiet Fan Speed Control and Dimmer, single pole only, no LED locator RTD01-10 1.5A Fan Control/ 300W Dimmer Z * NAFTA Compliant models available. For more information visit www.leviton.com/nafta Color Change Kits for IllumaTech Slide Controls DESCRIPTION CAT. NO. COLOR* Color Change Kit IPKIT-00 W, I, T, G, E, R, B Color Change Kit for IPL06; no LED IPKIT-LN W, I, T, G, E, R, B Color Change Kit for Fan Speed Control IPQFK-00 W, I, T, G, E, R, B IllumaTech controls come packaged with three colors. Products with suffix (-Z) include White, Ivory and Light Almond. Color Change Kits for IllumaTech Preset Slide Controls available in the following colors: White (-W), Ivory (-I), Light Almond (-T), Gray (-G), Black (-E), Red (-R) and Brown (-B). Mark 10® Powerline and Mark 7® 0-10V are registered trademarks of Advance Transformer Co. Decora and IllumaTech are registered trademarks and Decora Plus is a trademark of Leviton Manufacturing Co., Inc. Leviton Manufacturing Co., Inc. 201 North Service Road, Melville, NY 11747-3138 Telephone: 1-800-323-8920 • Fax: 1-800-832-9538 • Tech Line: (8:30AM-7:00PM E.T. Monday-Friday): 1-800-824-3005 Leviton Manufacturing of Canada, Ltd. 165 Hymus Boulevard, Pointe Claire, Quebec H9R 1E9 • Telephone: 1-800-469-7890 • Fax: 1-800-563-1853 Leviton S. de R.L. de C.V. Lago Tana 43, Mexico DF, Mexico CP 11290 • Tel. (+52) 55-5082-1040 • Fax. (+52) 5386-1797 • www.leviton.com.mx Visit our website at www.leviton.com © 2014 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice. G-8146E/L13-dp 1 3 9 3 S o u t h S a n ta F e D r , D e n v e r , C O 8 0 2 2 3 • 1 - 8 8 8 - 8 8 7 - 2 9 8 0 • i n f o @ e v o - l i t e . c o m • w w w . e v o - l i t e . c o m 5 DI-000-IP710-02C WARNINGS AND CAUTIONS: 1200VA 1500VA Single 1200VA 1500VA Two Gang 1200VA 1500VA More than 2 Devices √ OFF ON OFF OFF OFF ON ON ON ON ON ON OFF OFF ON ON OFF ON ON ON OFF Single Pole (One location) or 3-Way (Multi-location) Fluorescent Slide Dimmer Ground Neutral This wire is used in 3-way installations only. For single pole installations, do not remove this insulating label. Red Violet Gray Green Black Insert wires straight then twist clockwise Step 3a Single-Pole Wiring Application: Red Black White Primary Side To Lamps Yellow Red Connect wires per WIRING DIAGRAM as follows: Screw wire nuts on clockwise making sure no bare conductors show below the wire connectors. Secure each connector with electrical tape. Dimmer Red Gray Violet Wiring Diagram 1 Red Black Insulating Label Green Ground 0-10 VDC Blue Ballast • Green dimmer Ground lead to Green or bare copper wire in wall box. • Black dimmer lead to Line Hot wall box wire. • Red dimmer lead without insulating label to Load wall box wire. • Remaining Red dimmer lead should have Red insulation label affixed. NOTE: If insulating label is not affixed to Red lead, use a small wire nut or electrical tape to cap off. • Violet dimmer lead to (+) Violet connection on ballast. • Gray dimmer lead to (-) Gray connection on ballast. • Proceed to Step 4. Hot (Black) Dimmer Green Ground Red Blue Black Red To circuit #2 ODP Neutral Ground Insert wires straight then twist clockwise Step 3b 3-Way Wiring Application: Violet Gray Black Green Red Red Electrical Tape Connect wires per WIRING DIAGRAM as follows: Screw wire nuts on clockwise making sure no bare conductors show below the wire connectors. Secure each connector with electrical tape. NOTE: Dimmer can be installed on either the Load or Line side. Red Black Black White Primary Side Common Terminal (Black Screw) Green Ground 3-Way Switch Wiring Diagram 3 Dimmer Violet Gray Red Green Ground Red Red Dimmer Green Ground Black Red To Lamps ODP wall box: Step 4 Testing your Dimmer prior to mounting in • Restore power at circuit breaker or fuse. • Carefully holding Dimmer as shown, move slider control lever to highest position. Lights should turn ON to brightest level. If lights do not turn ON, depress push-button switch once. Lights should turn ON to brightest level. If lights still do not turn ON, refer to the TROUBLESHOOTING section. Installation may now be completed by carefully positioning all wires to provide room in wall box for dimmer. Mount dimmer into box with mounting screws supplied. Attach wallplate. TURN OFF POWER AT CIRCUIT BREAKER OR FUSE. Step 5 Dimmer Mounting: Blue Red Yellow To Additional Ballast To Lamps To Additional Ballast Power: Restore power at circuit breaker or Step 6 Restore fuse. Installation is complete. Black White 0-10 VDC Ballast Primary Side Violet Gray Cap off Black wire with Wire Connector Red Blue Black White Red 120V/277V White Red Black Red Wiring Diagram 4 Two Location Control with ODP Power Pack Application Green Ground 3-Way Switch Common Terminal (Black Screw) Neutral (White) Line 120/277VAC, 60Hz Hot (Black) 0-10 VDC Blue Ballast Yellow • Green dimmer Ground lead to Green or bare copper wire in wall box. • Black dimmer lead to tagged (common) wall box wire identified. • Remove Red insulating label from Red lead. • Any Red dimmer lead to Line Hot wall box wire. • Remaining Red dimmer lead to the Load Hot wall box wire. • Violet dimmer lead to (+) Violet connection on ballast. • Gray dimmer lead to (-) Gray connection on ballast. Hot (Black) Line 120/277VAC, 60Hz Neutral (White) To Additional Ballast To Lamps Red Black 0-10 VDC Blue Ballast Yellow White Primary Side Violet Gray Red Cap off Black wire with Wire Connector Red Blue Black Red 120V/277V To Lamps Black White Red Black 0-10 VDC Blue Ballast Yellow White Primary Side To Additional Ballast Violet Gray Red Cap off Black wire ODP 120V/277V with Wire Connector Hot (Black) Red Red Black White Red Wiring Diagram 2 Single Location Control with ODP Power Pack Application Neutral (White) Line 120/277VAC, 60Hz Insulating Label Hot (Black) Red Line 120/277VAC 60Hz Neutral (White) Electrical Tape • Use only one (1) dimmer in a 3- or 4-way circuit. The switch(es) will turn the light on at the brightness level selected at the dimmer. • Lighting fixture and dimmer must be grounded. • Disconnect power at circuit breaker or fuse when servicing fixture. • Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL. WARNINGS AND CAUTIONS: INSTALLATION INSTRUCTIONS Cat. No. IP710-DL (Lighted) 1200VA-120VAC, 60Hz 1500VA-277VAC, 60Hz For use with Advance Transformer Mark 7™ 0-10V, OSRAM Sylvania Quicktronic Helios or equivalent dimmable ballasts. when Steps are completed. Step 2 Preparing wires: • For 3-Way Application, go to Step 3B. Strip 5/8" (1.6 cm) Strip Gage 5/8" (1.6 cm) • For Single-Pole Application, go to Step 3A. • Remove 5/8" (1.6 cm) of insulation from each wire in the wall box (shown). • Make sure that the ends of the wires from the wall box are straight (cut if necessary). • Pull off pre-cut insulation from Dimmer leads. NOTE: Ensure that low-voltage wiring (for Gray and Violet connection of dimmer) is installed at wall box that will house the IP710 Dimmer. OFF OFF OFF OFF POWER at circuit breaker or fuse and test that power is off before wiring! Step 1 WARNING: To avoid fire, shock, or death; TURN OFF NOTE: Use check boxes INSTALLING YOUR DIMMER ODP SWITCH RATINGS: 20 Amps for 120 and 277 VAC Ballast For applications using Leviton's ODP (Wiring Diagrams 2 & 4 and Tables 3 & 4), ODP switch ratings are as follows (refer to ODP Instruction Sheet for additional information): NOTE: For additional switching capacity (up to 50 ballast), use dimmers in conjuction with a Leviton ODP 120/277V Power Pack. For direct load application configurations (Wiring Diagrams 1 and 3), refer to Table 1 and Table 2 for ballast information. 0-10VDC ballasts are rated in Volt-Amps (VA). The maximum number of ballast per dimmer is based on the load VA rating (see Maximum Load per Dimmer table) or 50 ballast maximum, which ever is less. The maximum bulb wattage is determined by the efficiency of the ballast. The tables on the next page show the maximum number of ballasts that can be connected to a single dimmer for different 0-10VDC ballasts. MAXIMUM BULB WATTAGE: • To be installed and/or used in accordance with appropriate electrical codes and regulations. • If you are unsure about any part of these instructions, consult a qualified electrician. • To avoid overheating and possible damage to this device and other equipment, use only with the appropriate Advance Transformer 120/277V Mark 7™ 0-10V or OSRAM Sylvania Quicktronic Helios electronic ballasts for controlling the specific fluorescent lamps. Electrical Tape Pencil Ruler Tools needed to install your Dimmer: Slotted/Philips Screwdriver Pliers Cutters Changing the color of your Dimmer: Your Dimmer includes two color options. The Dimmer ships with the White frame attached. To change color of frame, proceed as follows: Push in side at tab Line up tabs and to release press in side to attach Move the slider up or down one full cycle to automatically engage the slider control mechanism. Installing Dimmer by itself or with other devices: If installing Dimmer in a single device application, proceed with the INSTALLING YOUR DIMMER section. If installing Dimmer in a multi-device application, proceed as follows: MULTI-DEVICE APPLICATION: Do not remove outer side sections Remove all inner side sections NOTE: You only need to remove side sections if installing with other dimmers or if it does not fit in wall box – not when installing with mechanical switches. Bend back and forth to remove side section When installing more than one dimmer in the same location, the side sections of the mounting strap must be removed. Use pliers to carefully bend side sections back and forth until they break off. No derating is required in this mult-device installation as referenced in the following chart. 120 277 Volts MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE IP710-DL IP710-DL Cat. No. 6 1 3 9 3 S o u t h S a n ta F e D r , D e n v e r , C O 8 0 2 2 3 • 1 - 8 8 8 - 8 8 7 - 2 9 8 0 • i n f o @ e v o - l i t e . c o m • w w w . e v o - l i t e . c o m OPERATION NOTE: The indicator light will illuminate when the Load is OFF to facilitate access in the dark. BRIGHTEN & DIM: Move slider control lever - Lights will BRIGHTEN or DIM. Depress push-button switch to OFF position - Lights will turn OFF. ON/OFF: Depress push-button switch to ON position - Lights will turn ON. NOTE: If using the dimmer in a 3-way application, the lights will turn ON at brightness set on dimmer's slide control lever. The lights can be controlled from either the dimmer or the switch location. TROUBLESHOOTING • Lights Flickering - Lamp has a bad connection. - Wires not secured firmly with wire connectors. • Light does not turn ON and ON/OFF LED does not turn ON - Circuit breaker or fuse has tripped. - Lamp is burned out. - Lamp Neutral connection is not wired. NOTE: If further information is needed in identifying the HOT wire in a 3-Way application, go to Leviton's website at www.leviton.com. w/ w/ w/ w/ 1 1 1 1 to 3 #14, #16 or #18 or 2 #16 or #18 to 4 #16 or #18 to 3 #16 or #18 For non-standard wiring applications, refer to Wire Nut and Connector Size Chart #12 #12 #14 #14 WIRE CONNECTOR / # OF COND. COMBINATION CHART 1212- Advance Mark 7™ Part No. F25T8 F25T8 F25T8 F32T8 F32T8 F32T8 FT40W/2G11 Lamp 277 277 277 277 277 277 277 277 277 277 277 40 N/A 40 N/A 20 N/A 20 N/A 30 N/A 30 N/A 15 N/A 15 N/A 23 N/A 23 N/A 12 N/A 12 N/A 40 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 49 N/A 49 N/A 25 N/A 25 N/A 38 N/A 38 N/A 20 N/A 20 N/A 30 N/A 30 N/A 15 N/A 15 N/A 21 50 31 30 19 15 45 24 22 15 12 Table 1 Cat. No. IP710, 120/277V, For use with Advance Transformer 120/277V Mark 7™ Electronic Ballasts RZT-I32 RZT-2S32 RZT-3S32 RZT-132 RZT-2S32 RZT-3S32 RZT-1TTS40 F17T8 F25T8 F25T8 F25T8 F25T8 F25T8 F32T8 F32T8 F32T8 F32T8 F32T8 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 Max. # Ballasts/Dimmer for Multi-gang 1500VA@ Voltage 1200VA@ 120V 277V N/A 47 N/A 23 N/A 15 N/A 35 N/A 18 N/A 12 N/A 31 VZT-4S32 VZT-132 VDC-2S32-TP VZT-2S32 VZT-3S32 VZT-4S32 VZT-132 VDC-2S32-TP VZT-2S32 VZT-3S32 VZT-4S32 CFM26W/GX24Q CFM26W/GX24Q CFM26W/GX24Q CFM26W/GX24Q CFM26W/GX24Q CFM26W/GX24Q CFM26W/GX24Q CFM26W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFQ26W/G24Q 120 120 120 120 120 120 120 IZT-1T42-M2-BS@120 IZT-1T42-M2-BS@277 IZT-1T42-M2-LD@120 IZT-1T42-M2-LD@277 IZT-2Q26-M2-BS@120 IZT-2Q26-M2-BS@277 IZT-2Q26-M2-LD@120 IZT-2Q26-M2-LD@277 IZT-1T42-M2-BS@120 IZT-1T42-M2-BS@277 IZT-1T42-M2-LD@120 IZT-1T42-M2-LD@277 IZT-2T42-M3-BS@120 IZT-2T42-M3-BS@277 IZT-2T42-M3-LD@120 IZT-2T42-M3-LD@277 IZT-1T42-M2-BS@120 IZT-1T42-M2-BS@277 IZT-1T42-M2-LD@120 IZT-1T42-M2-LD@277 IZT-2T42-M3-BS@120 IZT-2T42-M3-BS@277 IZT-2T42-M3-LD@120 IZT-2T42-M3-LD@277 IZT-1T42-M2-BS@120 QTP1x32T8/120 Dim5-B QTP1x32T8/120 Dim5-B QTP1x32T8/120 Dim5-B QTP1x32T8/120 Dim5-B QTP1x32T8/120 Dim5-B QTP1x32T8/120 Dim5-B QTP1x32T8/120 Dim5-B QTP2x32T8/120 Dim5-B QTP2x32T8/120 Dim5-B QTP2x32T8/120 Dim5-B QTP3x32T8/120 Dim5-Q QTP3x32T8/120 Dim5-Q QTP3x32T8/120 Dim5-Q QTP4x32T8/120 Dim10-B QTP4x32T8/120 Dim10-B QTP4x32T8/120 Dim10-B OSRAM Sylvania Quicktronic Helios Part No. F17T8 FBO16T8 F25T8 FBO24T8 F32T8 FBO32T8/U/6 FBO31T8/U F32T8 FBO32T8/U/6 FBO31T8/U F32T8 FBO32T8/U/6 FBO31T8/U F32T8 FBO32T8/U/6 FBO31T8/U F17T8 FBO16T8 F25T8 FBO24T8 F32T8 FBO32T8/U/6 FBO31T8/U F32T8 FBO32T8/U/6 FBO31T8/U F32T8 FBO32T8/U/6 FBO31T8/U F32T8 FBO32T8/U/6 FBO31T8/U Lamp 120 120 120 120 120 120 277 277 277 277 277 277 277 277 277 277 277 277 277 277 277 277 N/A N/A N/A N/A N/A N/A 18 9 19 10 19 10 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 23 12 24 12 24 12 N/A N/A N/A N/A N/A N/A 50 50 50 50 45 45 45 21 21 22 15 15 16 9 9 10 VZT-4S32 VZT-132 VDC-2S32-TP VZT-2S32 VZT-3S32 VZT-4S32 VZT-132 VDC-2S32-TP VZT-2S32 VZT-3S32 VZT-4S32 RZT-I32 RZT-2S32 RZT-3S32 RZT-132 RZT-2S32 RZT-3S32 RZT-1TTS40 Advance Mark 7™ Part No. CFM26W/GX24Q CFM26W/GX24Q CFM26W/GX24Q CFM26W/GX24Q CFM26W/GX24Q CFM26W/GX24Q CFM26W/GX24Q CFM26W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM32W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFM42W/GX24Q CFQ26W/G24Q F17T8 F25T8 F25T8 F25T8 F25T8 F25T8 F32T8 F32T8 F32T8 F32T8 F32T8 F25T8 F25T8 F25T8 F32T8 F32T8 F32T8 FT40W/2G11 Lamp 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 120-277 277 277 277 277 277 277 277 277 277 277 277 50 N/A 50 N/A 40 N/A 40 N/A 50 N/A 50 N/A 20 N/A 20 N/A 46 N/A 46 N/A 24 N/A 24 N/A 50 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 50 N/A 50 N/A 50 N/A 50 N/A 50 N/A 50 N/A 50 N/A 50 N/A 50 N/A 50 N/A 45 N/A 45 N/A 50 50 50 50 50 45 50 50 50 45 26 120 120 120 120 120 120 120 IZT-1T42-M2-BS@120 IZT-1T42-M2-BS@277 IZT-1T42-M2-LD@120 IZT-1T42-M2-LD@277 IZT-2Q26-M2-BS@120 IZT-2Q26-M2-BS@277 IZT-2Q26-M2-LD@120 IZT-2Q26-M2-LD@277 IZT-1T42-M2-BS@120 IZT-1T42-M2-BS@277 IZT-1T42-M2-LD@120 IZT-1T42-M2-LD@277 IZT-2T42-M3-BS@120 IZT-2T42-M3-BS@277 IZT-2T42-M3-LD@120 IZT-2T42-M3-LD@277 IZT-1T42-M2-BS@120 IZT-1T42-M2-BS@277 IZT-1T42-M2-LD@120 IZT-1T42-M2-LD@277 IZT-2T42-M3-BS@120 IZT-2T42-M3-BS@277 IZT-2T42-M3-LD@120 IZT-2T42-M3-LD@277 IZT-1T42-M2-BS@120 Max. # Ballasts/Dimmer for Multi-gang 1500VA@ Voltage 1200VA@ 120V 277V N/A 50 N/A 41 N/A 28 N/A 50 N/A 36 N/A 24 N/A 50 Table 3 Cat. No. IP710, 120/277V, For use with Advance Transformer 120/277V Mark 7™ Electronic Ballasts and ODP Power Pack MAXIMUM NUMBER OF BALLASTS THAT CAN BE CONNECTED TO A SINGLE DIMMER Table 2 Cat. No. IP710, 120/277V, For use with 120/277V OSRAM Sylvania Quicktronic Helios Electronic Ballasts QTP1x32T8/277 Dim5-B QTP1x32T8/277 Dim5-B QTP1x32T8/277 Dim5-B QTP1x32T8/277 Dim5-B QTP1x32T8/277 Dim5-B QTP1x32T8/277 Dim5-B QTP1x32T8/277 Dim5-B QTP2x32T8/277 Dim5-B QTP2x32T8/277 Dim5-B QTP2x32T8/277 Dim5-B QTP3x32T8/277 Dim5-Q QTP3x32T8/277 Dim5-Q QTP3x32T8/277 Dim5-Q QTP4x32T8/277Dim10-B QTP4x32T8/277 Dim10-B QTP4x32T8/277 Dim10-B FP54T5HO FP54T5HO FT55DL FT55DL FPC55 FPC55 277 277 277 277 277 277 Max. # Ballasts/Dimmer for Multi-gang 1500VA@ Voltage 1200VA@ 120V 277V N/A 50 N/A 50 N/A 43 N/A 45 N/A 37 N/A 37 N/A 38 N/A 17 N/A 17 N/A 18 N/A 12 N/A 12 N/A 13 N/A 9 N/A 9 N/A 9 QT1x54/120PHO-Dim QT2x54/120PHO-Dim QT1x54/120PHO-Dim QT2x54/120PHO-Dim QT1x54/120PHO-Dim QT2x54/120PHO-Dim FP54T5HO FP54T5HO FT55DL FT55DL FPC55 FPC55 120 120 120 120 120 120 120 120 120 120 120 120 120 120 120 120 QT1x54/277PHO-Dim QT2x54/277PHO-Dim QT1x54/277PHO-Dim QT2x54/277PHO-Dim QT1x54/277PHO-Dim QT2x54/277PHO-Dim QTP1x32T8/120 Dim5-B QTP1x32T8/120 Dim5-B QTP1x32T8/120 Dim5-B QTP1x32T8/120 Dim5-B QTP1x32T8/120 Dim5-B QTP1x32T8/120 Dim5-B QTP1x32T8/120 Dim5-B QTP2x32T8/120 Dim5-B QTP2x32T8/120 Dim5-B QTP2x32T8/120 Dim5-B QTP3x32T8/120 Dim5-Q QTP3x32T8/120 Dim5-Q QTP3x32T8/120 Dim5-Q QTP4x32T8/120 Dim10-B QTP4x32T8/120 Dim10-B QTP4x32T8/120 Dim10-B OSRAM Sylvania Quicktronic Helios Part No. F17T8 FBO16T8 F25T8 FBO24T8 F32T8 FBO32T8/U/6 FBO31T8/U F32T8 FBO32T8/U/6 FBO31T8/U F32T8 FBO32T8/U/6 FBO31T8/U F32T8 FBO32T8/U/6 FBO31T8/U F17T8 FBO16T8 F25T8 FBO24T8 F32T8 FBO32T8/U/6 FBO31T8/U F32T8 FBO32TA8/U/6 FBO31T8/U F32T8 FBO32T8/U/6 FBO31T8/U F32T8 FBO32T8/U/6 FBO31T8/U Lamp 120 120 120 120 120 120 277 277 277 277 277 277 277 277 277 277 277 277 277 277 277 277 N/A N/A N/A N/A N/A N/A 36 18 38 20 38 20 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 50 12 50 12 50 12 N/A N/A N/A N/A N/A N/A 50 50 50 50 50 50 50 21 21 22 15 15 16 9 9 10 Table 4 Cat. No. IP710, 120/277V, For use with 120/277V OSRAM Sylvania Quicktronic Helios Electronic Ballasts and ODP Power Pack QTP1x32T8/277 Dim5-B QTP1x32T8/277 Dim5-B QTP1x32T8/277 Dim5-B QTP1x32T8/277 Dim5-B QTP1x32T8/277 Dim5-B QTP1x32T8/277 Dim5-B QTP1x32T8/277 Dim5-B QTP2x32T8/277 Dim5-B QTP2x32T8/277 Dim5-B QTP2x32T8/277 Dim5-B QTP3x32T8/277 Dim5-Q QTP3x32T8/277 Dim5-Q QTP3x32T8/277 Dim5-Q QTP4x32T8/277Dim10-B QTP4x32T8/277 Dim10-B QTP4x32T8/277 Dim10-B FP54T5HO FP54T5HO FT55DL FT55DL FPC55 FPC55 277 277 277 277 277 277 Max. # Ballasts/Dimmer for Multi-gang 1500VA@ Voltage 1200VA@ 120V 277V N/A 50 N/A 50 N/A 50 N/A 50 N/A 50 N/A 50 N/A 50 N/A 34 N/A 34 N/A 36 N/A 24 N/A 24 N/A 26 N/A 18 N/A 18 N/A 18 QT1x54/120PHO-Dim QT2x54/120PHO-Dim QT1x54/120PHO-Dim QT2x54/120PHO-Dim QT1x54/120PHO-Dim QT2x54/120PHO-Dim FP54T5HO FP54T5HO FT55DL FT55DL FPC55 FPC55 120 120 120 120 120 120 120 120 120 120 120 120 120 120 120 120 QT1x54/277PHO-Dim QT2x54/277PHO-Dim QT1x54/277PHO-Dim QT2x54/277PHO-Dim QT1x54/277PHO-Dim QT2x54/277PHO-Dim DI-000-IP710-02C LIMITED 5 YEAR WARRANTY AND EXCLUSIONS Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Levitonʼs only obligation is to correct such defects by repair or replacement, at its option, if within such five year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise. 7 1 3 9 3 S o u t h S a n ta F e D r , D e n v e r , C O 8 0 2 2 3 • 1 - 8 8 8 - 8 8 7 - 2 9 8 0 • i n f o @ e v o - l i t e . c o m • w w w . e v o - l i t e . c o m