Users Manual

advertisement
Users Manual
Operating and Installation Instructions
Buffalo River Black Dimaond
Model:ECSL-0601A
Electronic Combination Controller
b.
c.
d.
e.
Note:
a.
b.
If no user code exists, push button “1”, One
Beep sounds, which prompts to enter user
code.
Enter a new six (6) digits code one time. One
Beep sounds, which indicates the entry is valid.
Re-enter the new six (6) digits code. One Beep
sounds, which indicates the codes entered in
steps c and d are the same and the adding user
process is successful.
If Two Beeps sound, the process fails. Repeat
steps a to d.
Verify the new code at least 3 times before
closing the door to make sure the code is
correct.
Operations between adjacent steps need be
finished in 10 seconds. Otherwise, the system
sets back to standby status.
7. Disable User Code
a. Enter the manager code and Hold Down Last
Digit of Code until One Beep and then Double
Beeps sound.
b. Push button “2”, Double Beeps sound, the
process of disabling user code is successful.
Note:
a. Operations between adjacent steps need be
finished in 10 seconds. Otherwise, the system
sets back to standby status.
10
8. Enable User Code
a. Enter the manager code and Hold Down Last
Digit of Code until One Beep and then Double
Beeps sound.
b. If the user code exists, push button “1”,
Double Beeps sound, the process of enabling
user code is successful.
Note:
a. Verify the code at least 3 times before closing
the door to make sure the code is correct .
b. Operations between adjacent steps need be
finished in 10 seconds. Otherwise, the system
sets back to standby status.
9. Delete User Code
a. Enter the manager code and Hold Down Last
Digit of Code until One Beep and then Double
Beeps sound.
b. Push button “3”, Double Beeps sound, the
process of deleting user code is successful.
Note:
a. Verify the manager code at least 3 times
before closing the door to make sure the code
is correct.
b. Operations between adjacent steps need be
finished in 10 seconds. Otherwise, the system
sets back to standby status.
11
Specifications:
Power Supply:
DC 9V
Power Supply Range:
DC 4.5V-12V
Standby Current :
<15μA
Active Current:
<20mA
Battery Low Voltage:
5.2±0.2V
Working Temperature:
-25℃~ +60℃
Working Humidity:
<95%
Storage Temperature:
-45℃~ +85℃
Password Length:
6 Digits
Mechanical System Life Span: >100,000 Cycles
Model: ECSL-0601A
User’s Manual Version V1.1120080418(E)
12
ATTENTIONS:
●
For indoor use only.
Battery Low Voltage: 5.2 ± 0.2V. The display
will alert low battery when battery voltage
reaches 5.2±0.2V. PLEASE REPLACE THE
BATTERY IMMEDIATELY.
Battery Replacement Instructions
●
1) In the back of Entry Pad you will see one 9 V
alkaline battery. Take the battery out of the
battery compartment. Gently pull on the battery
until it drops out.
2) Gently remove the connector by unsnapping it
from the two terminals on the top of the
battery.
Never Pull on the Battery Leads
3) Connect a new 9V Alkaline battery to the
battery clip.
4) Put the battery and the leads completely back
into the battery compartment.
●
Mounting and wiring refer to the instruction
in this manual
3
FEATURES:
1. Three Codes Capacity
a. Master code:
Manufacturer default 1-2-3-4-5-6
b. Manager code:
No record by default
c. User code:
No record by default
2. Master Code Function
a. Unlock
b. Change master code
c. Add or delete manager code
d. Enable or disable manager code
3. Function of Code for manager code
a. Unlock
b. Change manager code
c. Add or delete user code
d. Enable or disable user code
4. Function of Code for User Code
a. Unlock
b. Change user code
5. Wrong Entry Penalty
Entry of four (4) consecutive invalid codes results in
4
a 5-minute delay period.
i. The unit beeps at 5 second intervals.
ii. During delay period, removing batteries, the
entry pad stops counting time; reinstalling
batteries, the entry pad continues to count down
until 5 minutes delay period finishes.
6. Standby Status
The entry pad will turn into a standby status with a
long beep sound if there is no operation in 10
seconds after the system is activated.
7. Automatic Re-lock
The entry pad will re-lock in 4 seconds after a valid
entry is made and the door is open.
8. Low Battery Alert
a. Entry pad repeated beeping during an unlocking
indicates that the battery is low and needs
immediate replacement.
b. Manufacturer recommends the use of 9-Volt
premier alkaline batteries and an annual
maintenance replacement of the batteries.
5
USER OPERATING INSTRUCTIONS
1. ALWAYS PERFORM OPERATIONS
WITH THE ENTRY PAD UNLOCK.
2. Before closing the door, make sure all the
changes are correct.
3. Do not set the user code to six “0”.
1. Change Master Code, Manager Code or User
Code
a. Enter “0” six times. One Beep sounds, which
indicates the entry is valid and the system is
awaiting the code changing.
b. Enter the existing six (6) digits code one time.
One Beep sounds, which indicates the entry is
valid.
c. Enter a new six (6) digits code one time. One
Beep sounds, which indicates the entry is valid.
d. Re-enter the new six (6) digits code. One Beep
sounds, which indicates the codes entered in
steps c and d are the same and the code
changing process is successful.
e. If Two Beeps sound, the changing process
fails. The existing code is still valid. Repeat
steps a to d.
6
Note:
a.
Verify the new code at least 3 times before
closing the door to make sure the code is
correct.
b. The process for changing the manager code or
user code is the same.
c. Operations between adjacent steps need be
finished in 10 seconds. Otherwise, the system
sets back to standby status.
2. Add Manager Code
a. Enter the master code and Hold Down Last
Digit of Code until One Beep and then Double
Beeps sound.
b. If no manager code exists, push button “1”,
One Beeps sound, which prompts to enter
manager code.
c. Enter a new six (6) digits code one time. One
Beep sounds, which indicates the entry is valid.
d. Re-enter the new six (6) digits code. One Beep
sounds, which indicates the codes entered in
steps c and d are the same and the process is
successful.
e. If Two Beeps sound, the process fails. Repeat
steps a to d.
7
Note:
a.
b.
Verify the new code at least 3 times before
closing the door to make sure the code is
correct.
Operations between adjacent steps need be
finished in 10 seconds. Otherwise, the system
sets back to standby status.
3. Disable Manager Code
a. Enter the master code and Hold Down Last
Digit of Code until One Beep and then Double
Beeps sound.
b. Push button “2”, Double Beeps sound, the
process of disabling manager code is
successful.
Note:
a. Verify the master code at least 3 times before
closing the door to make sure the code is
correct.
b. Operations between adjacent steps need be
finished in 10 seconds. Otherwise, the system
sets back to standby status.
4. Enable Manager Code
a. Enter the master code and Hold Down Last
Digit of Code until One Beep and then Double
Beeps sound.
b. If the manager code exists, push button “1”,
8
Note:
a.
b.
Double Beeps sound, the process of enabling
manager code is successful.
Verify the manager code at least 3 times before
closing the door to make sure the code is
correct.
Operations between adjacent steps need be
finished in 10 seconds. Otherwise, the system
sets back to standby status.
5. Delete Manager Code
a. Enter the master code and Hold Down Last
Digit of Code until One Beep and then Double
Beeps sound.
b. Push button “3”, Double Beeps sound, the
process of deleting manager code is successful.
Note:.
a. Verify the master code at least 3 times before
closing the door to make sure the code is
correct.
b. Operations between adjacent steps need be
finished in 10 seconds. Otherwise, the system
sets back to standby status.
6. Add User Code
a. Enter the manager code and Hold Down Last
Digit of Code until One beep and then Double
Beeps sound.
9
Download