Bulletin 193-ERID
Remote Indication Display
For the E1 Plus Electronic Overload Relay
Advantages
Overview
• Remotely resets Bulletin 193/592
E1 Plus electronic overload relay
• Mounts and wires into standard
22 mm push button cutout
• View status of Bulletin 193/592 E1
Plus electronic overload relay from
front of electrical enclosure
- Overload trip
- Overload warning
- Side-mount module trip
- E1 Plus status
• Rated NEMA Type 4X and IP 66
The Allen-Bradley® Bulletin 193-ERID E1 Plus remote indication display
from Rockwell Automation is an intelligent reset button for the Bulletin
193/592 E1 Plus electronic overload relay. Remote indication displays
increase your motor maintenance productivity because maintenance
personnel can view the status and reset an E1 Plus from a closed electrical
enclosure. This minimizes the need for uncomfortable and cumbersome
personal protective equipment.
The remote indication display is physically mounted like a standard 22
mm push button. An adapter is available for 30 mm push button applications. In addition, only two wires are needed to supply module power,
establish communications, and provide a reset signal.
193-ERID (Back)
Increase your motor
maintenance productivity
with remote indication
displays.
193-ERID (Front)
6 / 2011
www.klinkmann.com
Product Selection
Description
Rated Insulation
Voltage (Ui)
Degree of Protection
Cat. No.
E1 Plus Remote Indicator Display
300V
IP 65/66
Type 4/4X/12/13
193-ERID
The remote indication display can be used with the following
Bulletin 193/592 E1 Plus protection side-mount
modules (Series B or later).
Description
Cat. No.
Jam Module
193-EJM
Ground Fault Current Module
193-EGF
Ground Fault Current & Jam Module
193-EGJ
PTC Thermistor Module
193-EPT
Remote Reset Module
193-ERR
Accessories
Description
Type
Pkg. Quantity
Cat. No.
30.5 mm to 22.5 mm Hole Size Adapter
This adapter allows a 22.5 mm push
button operator to be in stalled in a panel
with existing 30.5 mm mounting holes.
Note: Comes with anti-rotation washer.
Metal
1
800F-AHA1
Mounting Ring Wrench
The mounting ring wrench is used to
tighten plastic or metal mounting rings
quickly and securely.
N/A
1
800F-AW2
Replacement Mounting Ring
Plastic
1
Replacement Terminal Block Plug
N/A
1
Replacement LED Fault Code Label
N/A
1
193-NCRID
Allen-Bradley and Rockwell Software are trademarks of Rockwell Automation Inc.
Publication 193-PP025A-EN-P – May 2009
Copyright ©2009 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.
Rockwell_Power_193-ERID-E1-Plus_en_0611.pdf
Helsinki
St. Petersburg
Moscow
tel. +358 9 540 4940
automation@klinkmann.fi
tel. +7 812 327 3752
klinkmann@klinkmann.spb.ru
tel. +7 495 641 1616
moscow@klinkmann.spb.ru
Yekaterinburg
Samara
Кiev
tel. +7 343 376 5393
yekaterinburg@klinkmann.spb.ru
tel. +7 846 273 95 85
samara@klinkmann.spb.ru
tel. +38 044 495 33 40
klinkmann@klinkmann.kiev.ua
Riga
Vilnius
Tallinn
Мinsk
tel. +371 6738 1617
klinkmann@klinkmann.lv
tel. +370 5 215 1646
post@klinkmann.lt
tel. +372 668 4500
klinkmann.est@klinkmann.ee
tel. +375 17 200 0876
minsk@klinkmann.com
www.klinkmann.com