BOX INSTALLATION FL-540P INSTALLATION INSTRUCTIONS

advertisement
FSR
GANG DIVIDER ASSEMBLY
DIVIDER HOLDER MUST BE ORIENTED AS SHOWN WHEN ATTACHING
TO DIVIDERS, IN ORDER TO PROPERLY ASSEMBLE BOX INTERIOR.
4" BOX DIVIDER
DIVIDER
5"-6" BOX DIVIDER
7"-12" BOX DIVIDER
DIVIDER
FL-540P INSTALLATION INSTRUCTIONS
244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - Fax: 973.785.4207
BOX INSTALLATION
LOCATE AND POSITION BOX IN ACCORDANCE WITH FLOOR PLANS. HOLE TO BE
CUT IN FLOOR - 12-1/4" x 10-1/4". DROP FLOOR BOX THRU HOLE AND SECURE
WITH #8 HARDWARE (BY INSTALLER) - LIP ON BOX CAN ACCOMODATE #8 COUNTERSUNK SCREWS. REMOVE AND RETAIN TEMPORARY COVER AND SCREWS. ROUTE
CONDUITS TO BOX AS REQUIRED. PLACE THIS INSTALLATION GUIDE BACK INTO
BOX, ALONG WITH ALL SUPPLIED ITEMS, AND REINSTALL TEMPORARY COVER.
DIVIDER
#8 FLAT HEAD
HARDWARE
(BY INSTALLER)
DIVIDER HOLDER
(2) #8-32 x .25 LG
PAN HEAD
SCREW
(2) #8-32 x .25 LG
PAN HEAD
SCREW
(2) #8-32 x .25 LG
PAN HEAD
SCREW
DIVIDER HOLDER
DIVIDER HOLDER
GANG PLATE ASSEMBLY
* DIVIDER ASSEMBLY FOR 5" & 7" BOXES
POSITION DIVIDER ASSEMBLY IN BOX BEFORE INSTALLING
GANG PLATE ASSEMBLY. SECURE DIVIDER ASSEMBLY TO
GANG PLATE ASSEMBLY WITH SCREWS AS NOTED.
GANG
MOUNTING
PLATE
(4) #8-32 x .375 LG
SELF TAPPING
PAN HEAD
SCREW
(2) #8-32 x .25 LG
FLAT HEAD
SCREW
12-1/4" x 10-1/4" HOLE IN FLOOR
(8) #6-32 FLAT HEAD SCREW
TEMPORARY
COVER
DIVIDER ASSEMBLY
INSTALLING ELECTRONIC COMPONENTS
GANG
MOUNTING
BRACKET
INSTALLED
ELECTRONIC
COMPONENT
PULL WIRES AND CABLES TO BOX AS NECCESSARY (REMOVAL OF
GANG MOUNTING BRACKETS MAY BE REQUIRED). TERMINATE
WIRES AND CABLES TO ELECTRONIC COMPONENTS, AND INSTALL
ELECTRONIC COMPONENTS ONTO GANG MOUNTING BRACKETS.
REINSTALL TEMPORARY COVER IF FINISHED COVER IS TO BE
INSTALLED AT A LATER DATE.
FLOOR NOT SHOWN FOR CLARITY
OF CONDUIT INSTALLATION
43201
LIT1333
TYPICAL INSTALLATION
GANG MOUNTING BRACKET CONFIGURATION
PER CUSTOMER SPECIFICATIONS, CONFIGURE GANG MOUNTING BRACKETS AS SHOWN BELOW AND
REASSEMBLE INTO BOX (DECORA WALL PLATES SHOWN AS REFERENCE AND NOT INCLUDED).
CARPET OVER CONCRETE (COVER WITH EDGING)
EDGING
CARPET
DIVIDER
HOLDER
COVER PLATE
TEMPORARY COVER
FINISH COVER
FLOOR BOX
FLOOR BOX
(2) DIVIDER
HOLDER
FLOORING
MATERIAL
FLOORING
MATERIAL
GANG
MOUNTING
BRACKET
GANG
MOUNTING
BRACKET
VINYL FLOORING OVER CONCRETE (COVER WITHOUT EDGING)
OPTIONAL DIVIDER
1-GANG/2-GANG CONFIGURATION
GANG MOUNTING BRACKET
FLOOR BOX
FLOORING
MATERIAL
1-GANG/3-GANG CONFIGURATION
FINISH COVER
VINYL FLOORING
TEMPORARY COVER
OPTIONAL DIVIDER
GANG MOUNTING BRACKET
DIVIDER
HOLDER
DIVIDER
HOLDER
FLOOR BOX
FLOORING
MATERIAL
CENTER DIVIDER CONFIGURATION (NOT APPLICABLE ON 4" BOX)
SET ASIDE TEMPORARY COVER AND SCREWS FOR POSSIBLE RE-INSTALLATION.
REMOVE AND RETAIN GANG MOUNTING BRACKETS AND SCREWS TO CONFIGURE
CENTER DIVIDERS.
OPTIONAL DIVIDER
OPTIONAL
DIVIDER
2-GANG/2-GANG CONFIGURATION
3-GANG/1-GANG CONFIGURATION
REMOVABLE LARGE CENTER DIVIDER
GANG MOUNTING BRACKET
REMOVABLE SMALL
CENTER DIVIDER
(2) DIVIDER HOLDER
(NO DIVIDERS USED)
REMOVABLE SMALL
CENTER DIVIDER
POSSIBLE GANG DIVIDER LOCATION
REMOVABLE LARGE CENTER DIVIDER
4-GANG CONFIGURATION
BOTH GANG MOUNTING BRACKETS ARE IDENTICAL, AS IS THEIR CONFIGURATION CAPABILITY
Download