Wireless Push Button RFv2
Convenient – call customers
from wherever you are working.
Flexible – keep it with you on
its key chain or fix it in place
with the included hook-and-loop
fastener.
Easy – with a wireless Indicator
pack, just plug in power and
start calling customers.
 Good range, operation at  Clearly marked buttons,  Reliable performance,
30m (100 ft) or more
providing all indicator
even with EM or RF site
from indicator.
control functions (+1,
disturbance, using an
+10 and -1).
isolated indicator receiver
design.
 LED confirmation of
 No ‘cross talk’ between
 CE and FCC certified
button press and quick
separate systems,
system (FCC Rules and
response from Indicator.
uses unique push
Regulations Part 15,
button digital ID codes.
Subpart C)
Available products:
Wireless Push Button set RFv2
Indicator RF pack
(V2 & V3 Indicator wireless upgrade)
(Available as 2 or 3 digit, red or green display)
Indicator RF bracket (deeper
bracket for additional space
behind Indicator for Receiver)
Plug-in RFv2
Receiver for Indicator
Wireless Push Button (ID
code pre-recorded, no
set-up). Includes hook
and loop fastener set for
optional fixed mounting.
2008-02 Wireless Push Button RFv2.doc
Indicator RF (receiver
installed on Indicator)
Plug-in power supply with
5m (16 ½ feet) output cable
Wireless RFv2 Push Buttons, 2
each, with hook and loop sets
Also, applicable system
START & PLUS packs
Wireless Push Button RFv2
Wireless Push Button RFv2
32mm
(1.3 in)
51mm
(2 in)
Indicator Receiver RFv2
Frequency: 433.92 MHz (+/- max. 542kHz)
RF power output = max 10mW (10 dBm)
Channels: 2
Memory: 15 push button
ID codes per channel
Operating Voltage: 11-24
VDC or 11-24VAC
Operating Current: 8 mA @
12VDC(standby), 30 mA per
83mm channel @ 12 VDC(active)
(3.3 in) Relay rating: 10A @ 24VDC
or 120VAC per channel
Battery: Alkaline MN21 12V
Battery life: Approx. 11,000
push button presses (1 sec)
Button life: Approx. 100,000
button presses
Weight:
60gr (2 oz)
68mm
(2.7 in)
Weight: 150gr (5 oz)
Recording Push Button codes into Indicator Receiver
NOTE: Power must be ON to Indicator.
Recording Push Button(+):
1. Press & hold Mode Switch #1 for about 3 seconds. Release the
switch when the green LED at the top of the Receiver starts blinking.
2. Press the (+) button on the RF Push Button. The green LED will
turn off to show that the code is recorded.
Recording Push Button (-):
1. Press & hold Mode Switch #2 for about 3 seconds. Release the
switch when the red LED on the Receiver starts blinking.
2. Press the (-) button on the RF Push Button. The red LED will turn
off to show that the code is recorded.
Mode
Switch
#2
Mode
Switch
#1
NOTE: A maximum of 15 codes can be recorded per channel. To
clear all codes, press & hold Mode Switch #1 for about 3 seconds.
When the Receiver’s green LED starts blinking, release Mode
Switch #1, then press & hold it again for 3 seconds. Repeat the
procedure with Mode Switch #2.
Application: V2 / V3 RF systems (Indicators can be 2 or 3-digit)
MASTER
Indicator with
RF Receiver
V2 Adr = 21
V3 Adr = 51
TOM-Net data cable
connection from
MASTER to Slave
Indicator and between
multiple Slave Indicators
Max. of 15 RF
Push Buttons
per system
2008-02 Wireless Push Button RFv2.doc
Slave Indicators (non-RF)
V2 Adr = 20
V3 Adr = 50