" 86 " LOCKOUT RELAY

advertisement
" 86 " LOCKOUT RELAY
A typical Lockout Relay would have two positions "TRIP - RESET". Under normal
condition, the handle would be turned to "RESET" position and would remain mechanically
latched at this position. The Lockout Relay contact LR which is in series with the Lockout
Relay coil would be closed at the 'RESET" position only. The fault contact FC makes only
when there is a fault in the circuit.
When the Lockout Relay coil LR is energise, it would released the mechanical latch
holding the handle at 'RESET" position and the handle would spring return to 'TRIP"
position. So long as FC remains at close contact condition ( due tothe presence of a fault
in the circuit ) the handle will not latched at "RESET" position but would always spring
return to "TRIP "
L
N
FC
LR
D2
D1
LR
APPLICATION
Fig. 1
L
N
FC
The Lockout Relay is a high speed Automatic Trip/Manual Reset auxiliary relay permitting simultaneous operations of up to 48 contacts from 10A to 80A for AC and 10A to 63A
for DC.
Lockout Relays are normally connected to the fault sensing contacts of the circuit
breakers. If a fault should occur, the Lockout Relays ensure that all the critical circuits are
isolated and would remain isolated so long as the fault is not cleared. It's positive trip
action ensures that all the contacts would perform as to requirements and it multi-contact
arrangement eliminates the need for several control relays contacts.
LR
D2
D1
LR
Fig. 2
L
N
FC
LR
D1
D2
LR
Fig. 3
PRINCIPLE OF OPERATION
a.
TRIP
•
•
•
RESET
No Fault Condition - Fig. 1
Handle at "TRIP" position
LR contact open circuit because handle is at "TRIP" position.
FC contact open circuit because there is no fault condition
b.
No Fault Condition - Fig. 2
• Handle turn to "RESET " position
• LR contact close circuit because handle at "TRIP" position.
• FC contact open circuit because there is no fault condition.
c. Fault Condition - Fig. 3
• FC contact close circuit to energise Lockout Relay coil LR via the Lockout Relay
contact LR.
KRAUS & NAIMER BLUE LINE
46
RC/02/2004
" 86 " LOCKOUT RELAY
• When coil LR is energise, the mechanical latch holding the handle is release, and
the handle spring returns to "TRIP" position. Contact LR opens to isolate the coil from
the power supply to prevent overheating of the coil.
b. Lockout Relay without manual release. Testing of the switching system can be
carried out by energising the coil.
TYPES OF LOCKOUT RELAY
48
Two types of Lockout Relays are available:
a. Lockout Relay with Manual Release to allow testing of the of the switching system.
TRIP
RESET
48
TRIP
RESET
48
50
Switch Type
50
64
4 max.
Ratings
Ith2 current
Switch Type
Ratings
Ith2 current (A)
Number of Contacts
- 60 deg. switching
- 90 deg. switching
CA10M CA20M CA25M
CHR10M CHR16M
20
25
32
A11M
A14M
(A)
25
A11L
A14L
C26L
20
25
32
20
25
40
24
24
24
24
24
24
43
38
48
48
21
18
C26M
Number of Contacts
- 60 deg. switching
- 90 deg. switching
20
CA10L
CA20L
CA25L
CHR10L CHR16L
40
Fig. 4b - Contact Ratings
24
24
24
24
24
24
43
38
48
48
21
18
Fig. 4a - Contact Ratings
KRAUS & NAIMER BLUE LINE
47
RC/02/2004
" 86 " LOCKOUT RELAY
CONSTRUCTION DETAILS
WARNING
The parts of the Lockout Relays are:
The Electro-magnetic System
The coils of the electro-magnetic system is totally
encapsulated with a series built in contact LR. This contact will make at "RESET" or "ON"
position and opens at 'TRIP" or "OFF" position. The same coil of rated voltage can be used
for 50/60hz or DC. Coils are available for voltage of 24V-500V/50hz, 24V-660V/60hz and
24V-220V/DC. The specifications of the coils in ohms are:
24-28V
48V
100V
110V/125V
220/240V
Voltage
Resistance
2.72
7.53
31
43.2
171.5
Pull-in voltage
• Normal coil
70%
70%
70%
70%
70%
• Special coil
50%
50%
70%
50%
50%
To obtain maximum tripping speed, the Lockout Relay coils are rated for intermittent
duty only. Continous energisation of the coil and may result in overheating of the coil.
1.
2.
The Switching Contacts System
The contacts used are all double break fast switching silver alloy contacts and are
housed in high grade thermoplastic insulating materials. For corrosive environment like
petro-chemicals plants, gold contacts are available. Switching speed is 10 milli-seconds.
Type A11/A14 have four contact per stage of contact chamber and types C26/C32/C42
have 2 contacts per stage of contact chamber.
OPTIONAL EXTRAS
a. Trip Indicator M120
The Trip Indicator is a mechanical coloured indicator to show the "TRIP /"RESET"
that the handle has been turned to. Hence , when the handle is turn and remain latch at
"RESET" position, the trip indicator shows Green on the window of the escutcheon plate.
If a fault condition arises, the handle will turn to "TRIP" position and the indicator will
show Red on the window. The coding for the trip indicator as follows:
• Square escutcheon plate
S1 M120/A21A
M999/US0019
In selecting the coil voltage of the Lockout Relay, it is important to verify if additional coils
e.g. protective relay coils etc.would be connected in series with the Lockout Relay coil. I n
order to ensure that the Lockout Relay can trip should a fault occurs, it is
important :
• To adjust the setting of the protective relay T61 coil so that the Lockout Relay can trip
when the coil is energise- refer Fig. 5b.
• If the protective relay T61 coil is not adjustable, it is important that the coil voltage of the
Lockout Relay is properly selected to match with the series coil T61 so the Lockout Relay
coil can trip when energise. In such a case, the rated coil voltage of the Lockout relay should
be lower than the DC bus voltage. It is important to ensure that the voltage V1 across the
Lockout Relay coil 86 should not be lower than the Pull-in voltage as
specified
above.
• The current flowing in the circuit is sufficient to energise and trip the Lockout Relay coil.
DC Trip Bus
•
DC Trip Bus
(+)
(+)
TS1
Protective
Relay
Coil
D1
ENGRAVINGS
V2
Various types of engravings are available. The common types are:
Engraving
Ordering code
"OFF-ON"
S1 F721/A1B/A-P1
"TRIP-CLOSE"
S1 F224/A1B/A-P1
"TRIP-RESET"
S1 F*SG0076
D1
V1
Lockout
Relay
Rectangular escutcheon plate
S1 M120/B21A
M999/US0019
86
Lockout
Relay
D2
(-)
Fig.5a Lockout Relay
withiout series relay coil
KRAUS & NAIMER BLUE LINE
86
V1
D2
(-)
Fig.5b Lockout Relay with
with series relay coil
48
RC/02/2004
" 86 " LOCKOUT RELAY
Typical Requirement
Ordering Code of Standard Switch
1. Lockout Relay with manual reset
2. Contact rating 40A
3. Contact requirement 4NO + 4 NC
4. Coil voltage 110VDC
5. Engraving "TRIP-CLOSE"
6. Trip Indicator required.
C26
M
A723
/
D 110
Contact Rating
Type
HOW TO ORDER
• M - With manual reset
• L - Without manual reset
When ordering the Lockout Relay, the following datas are to be provided:
1. Type of Lockout Relay required
• Without Manual Release ( Type C26Letc.)
• With Manual release (Type C26M etc )
Manual Release type have a pushbutton which manually trips the Lockout Relay for
circuit testing of the contacts. The location of the pushbutton on the front of the unit
makes it unnecessary for the operator to go inside a live panel in order to mechanically
trip the device from behind the switch.
Contact Configuration
Frequency
• A - 50hz
• B - 60hz
• D - DC
Coil Voltage
• 024
• 038
• 048
• 060
• 110
• 220
• 380
2. Contact Ratings required - refer Fig. 4
3. Contact Configuration required
Specify contact arrangements as follows;
• Number of contacts making at "TRIP" position and if required the terminal number.
• Number of contacts making at "RESET" position and if required, the terminal
number.
4. Coil voltage required.
- 24v to 28v
- 32v to 40v
- 42v to 50v
- 60v
- 110v to 125v
- 220v to 240v
- 380v to 440v
The ordering code to be as follows:
Item
Code
Description
5. Engraving on plate
For example, "TRIP-RESET"
6. Optional Extras
- Trip Indictor
KRAUS & NAIMER BLUE LINE
49
RC/02/2004
"86" Lockout Relay - Without Manual Release
Plate
Engraving
Contacts
Optional Extras
2a + 2b
• Trip indicator M120
• Lockout Relay V340
64
TRIP
RESET
64
4a + 4b
• Trip indicator M120
• Lockout Relay V340
6a + 6b
• Trip indicator M120
• Lockout Relay V340
8a + 8b
• Trip indicator M120
• Lockout Relay V340
10a + 10b
• Trip indicator M120
• Lockout Relay V340
12a + 12b
• Trip indicator M120
• Lockout Relay V340
64
TRIP
2a + 2b
• Trip indicator M120
• Lockout Relay V340
RESET
Electrical
Diagram
TRIP
RESET
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
Coil
Voltage
Switch
Reference
SIS
Code
Handle
(Black)
Switch
Dimension
Depth( mm ) (Refer Pg. 2)
20A
25A
40A
24VDC
24VDC
24VDC
CHR10L A721/D024 E
CHR16L A721/D024 E
C26L A721/D024 E
SIS0001
SIS0001
SIS0001
66
66
64
S1/PE
S1/PE
S1/PE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10L A723/D024 E
CHR16L A723/D024 E
C26L A723/D024 E
SIS0001
SIS0001
SIS0001
94
94
90
S1/PE
S1/PE
S1/PE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10L SGZ873/D024 E
CHR16L SGZ873/D024 E
C26L SGZ873/D024 E
SIS0001
SIS0001
SIS0001
122
122
112
S1/PE
S1/PE
S1/PE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10L SGZ874/D024 E
CHR16L SGZ874/D024 E
C26L RCZ174/D024 E
SIS0001
SIS0001
SIS0001
150
150
140
S1/PE
S1/PE
S1/PE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10L SGZ875/D024 E
CHR16L SGZ875/D024 E
C26L SGZ875/D024 E
SIS0001
SIS0001
SIS0001
178
178
166
S1/PE
S1/PE
S1/PE
20A
25A
24VDC
24VDC
CHR10L SGZ876/D024 E
CHR16L SGZ876/D024 E
SIS0001
SIS0001
205
205
S1/PE
S1/PE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10L A721/D110 E
CHR10L A721/D110 E
C26L A721/D110 E
SIS0001
SIS0001
SIS0001
66
66
64
S1/PE
S1/PE
S1/PE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10L A723/D110 E
CHR16L A723/D110 E
C26L A723/D110 E
SIS0001
SIS0001
SIS0001
94
94
90
S1/PE
S1/PE
S1/PE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10L SGZ873/D110 E
CHR16L SGZ873/D110 E
C26L SGZ873/D110 E
SIS0001
SIS0001
SIS0001
122
122
112
S1/PE
S1/PE
S1/PE
64
Rating
Ith2
4a + 4b
• Trip indicator M120
• Lockout Relay V340
6a + 6b
• Trip indicator M120
• Lockout Relay V340
KRAUS & NAIMER BLUE LINE
Coil
D1
D2
50
RC/02/2004
"86" Lockout Relay - Without Manual Release
Plate
Engraving
Contacts
Optional Extras
8a + 8b
• Trip indicator M120
• Lockout Relay V340
64
TRIP
RESET
64
10a + 10b
• Trip indicator M120
• Lockout Relay V340
12a + 12b
• Trip indicator M120
• Lockout Relay V340
2a + 2b
• Trip indicator M120
• Lockout Relay V340
64
TRIP
RESET
64
4a + 4b
• Trip indicator M120
• Lockout Relay V340
6a + 6b
• Trip indicator M120
• Lockout Relay V340
8a + 8b
• Trip indicator M120
• Lockout Relay V340
Electrical
Diagram
TRIP
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
Coil
10a + 10b
• Trip indicator M120
• Lockout Relay V340
D1
12a + 12b
• Trip indicator M120
• Lockout Relay V340
KRAUS & NAIMER BLUE LINE
RESET
Rating
Ith2
Coil
Voltage
Switch
Reference
SIS
Code
Handle
(Black)
Switch
Dimension
Depth( mm ) (Refer Pg. 2)
20A
25A
40A
110VDC
110VDC
110VDC
CHR10L SGZ874/D110 E
CHR16L SGZ874/D110 E
C26L SGZ874/D110 E
SIS0001
SIS0001
SIS0001
150
150
140
S1/PE
S1/PE
S1/PE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10L SGZ875/D110 E
CHR16L SGZ875/D110 E
C26L SGZ875/D110 E
SIS0001
SIS0001
SIS0001
178
178
166
S1/PE
S1/PE
S1/PE
16A
25A
110VDC
110VDC
CHR10L SGZ876/D110 E
CHR16L SGZ876/D110 E
SIS0001
SIS0001
205
205
S1/PE
S1/PE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10L A721/D125E
CHR16L A721/D125E
C26L A721/D125E
SIS0001
SIS0001
SIS0001
66
66
64
S1/PE
S1/PE
S1/PE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10L A723/D125E
CHR16L A723/D125E
C26L A723/D125E
SIS0001
SIS0001
SIS0001
94
94
90
S1/PE
S1/PE
S1/PE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10L SGZ873/D125 E
CHR16L SGZ873/D125 E
C26L SGZ873/D125 E
SIS0001
SIS0001
SIS0001
122
122
112
S1/PE
S1/PE
S1/PE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10L SGZ874/D125 E
CHR16L SGZ874/D125 E
C26L SGZ874/D125 E
SIS0001
SIS0001
SIS0001
150
150
140
S1/PE
S1/PE
S1/PE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10L SGZ875/D125 E
CHR16L SGZ875/D125 E
C26L SGZ875/D125 E
SIS0001
SIS0001
SIS0001
178
178
166
S1/PE
S1/PE
S1/PE
20A
25A
125VDC
125VDC
CHR10L SGZ876/D125 E
CHR16L SGZ876/D125 E
SIS0001
SIS0001
205
205
S1/PE
S1/PE
D2
51
RC/02/2004
"86" Lockout Relay - Without Manual Release
Plate
Engraving
Contacts
Optional Extras
2a + 2b
• Trip indicator M120
• Lockout Relay V340
64
TRIP
CLOSE
64
4a + 4b
• Trip indicator M120
• Lockout Relay V340
6a + 6b
• Trip indicator M120
• Lockout Relay V340
8a + 8b
• Trip indicator M120
• Lockout Relay V340
10a + 10b
• Trip indicator M120
• Lockout Relay V340
12a + 12b
• Trip indicator M120
• Lockout Relay V340
64
TRIP
2a + 2b
• Trip indicator M120
• Lockout Relay V340
CLOSE
Electrical
Diagram
TRIP
CLOSE
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
Coil
Voltage
Switch
Reference
SIS
Code
Handle
(Black)
Switch
Dimension
Depth( mm ) (Refer Pg. 2)
20A
25A
40A
24VDC
24VDC
24VDC
CHR10L A721/D024E
CHR16L A721//D024E
C26L A721/SD024E
SIS0002
SIS0002
SIS0002
66
66
64
S1/PE
S1/PE
S1/PE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10L A723/D024E
CHR16L A723/D024E
C26L A723/D024E
SIS0002
SIS0002
SIS0002
94
94
90
S1/PE
S1/PE
S1/PE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10L SGZ873/D024 E
CHR16L SGZ873/D024 E
C26L SGZ873/D024 E
SIS0002
SIS0002
SIS0002
122
122
112
S1/PE
S1/PE
S1/PE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10L SGZ874/D024 E
CHR16L SGZ874/D024 E
C26L SGZ874/D024 E
SIS0002
SIS0002
SIS0002
150
150
141
S1/PE
S1/PE
S1/PE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10L SGZ875/D024 E
CHR16L SGZ875/D024 E
C26L SGZ875/D024 E
SIS0002
SIS0002
SIS0002
178
178
166
S1/PE
S1/PE
S1/PE
20A
25A
24VDC
24VDC
CHR10L SGZ876/D024 E
CHR16L SGZ876/D024 E
SIS0002
SIS0002
205
205
S1/PE
S1/PE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10L A721/D110E
CHR16L A721/D110E
C26L A721/D110E
SIS0002
SIS0002
SIS0002
66
66
64
S1/PE
S1/PE
S1/PE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10L A723/D110E
CHR16L A723/D110E
C26L A723/D110E
SIS0002
SIS0002
SIS0002
94
94
90
S1/PE
S1/PE
S1/PE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10L SGZ873/D110 E
CHR16L SGZ873/D110 E
C26L SGZ873/D110 E
SIS0002
SIS0002
SIS0002
122
122
112
S1/PE
S1/PE
S1/PE
64
Rating
Ith2
4a + 4b
• Trip indicator M120
• Lockout Relay V340
6a + 6b
• Trip indicator M120
• Lockout Relay V340
KRAUS & NAIMER BLUE LINE
Coil
D1
D2
52
RC/02/2004
"86" Lockout Relay - Without Manual Release
Plate
Engraving
Contacts
Optional Extras
8a + 8b
• Trip indicator M120
• Lockout Relay V340
64
TRIP
CLOSE
64
10a + 10b
• Trip indicator M120
• Lockout Relay V340
12a + 12b
• Trip indicator M120
• Lockout Relay V340
2a + 2b
• Trip indicator M120
• Lockout Relay V340
64
TRIP
CLOSE
64
4a + 4b
• Trip indicator M120
• Lockout Relay V340
6a + 6b
• Trip indicator M120
• Lockout Relay V340
8a + 8b
• Trip indicator M120
• Lockout Relay V340
Electrical
Diagram
TRIP
CLOSE
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
Rating
Ith2
Coil
Voltage
Switch
Reference
SIS
Code
Handle
(Black)
Switch
Depth( mm )
Dimension
20A
25A
40A
110VDC
110VDC
110VDC
CHR10L SGZ874/D110 E
CHR16L SGZ874/D110 E
C26L SGZ874/D110 E
SIS0002
SIS0002
SIS0002
150
150
140
S1/PE
S1/PE
S1/PE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10L SGZ875/D110 E
CHR16L SGZ875/D110 E
C26L SGZ875/D110 E
SIS0002
SIS0002
SIS0002
178
178
166
S1/PE
S1/PE
S1/PE
16A
25A
110VDC
110VDC
CHR10L SGZ876/D110 E
CHR16L SGZ876/D110 E
SIS0002
SIS0002
205
205
S1/PE
S1/PE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10L A721/D125 E
CHR16L A721/D125 E
C26L A721/D125 E
SIS0002
SIS0002
SIS0002
66
66
64
S1/PE
S1/PE
S1/PE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10L A723/D125 E
CHR16L A723/D125 E
C26L A723/D125 E
SIS0002
SIS0002
SIS0002
94
94
90
S1/PE
S1/PE
S1/PE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10L SGZ873/D125 E
CHR16L SGZ873/D125 E
C26L SGZ873/D125 E
SIS0002
SIS0002
SIS0002
122
122
112
S1/PE
S1/PE
S1/PE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10L SGZ874/D125 E
CHR16L SGZ874/D125 E
C26L SGZ874/D125 E
SIS0002
SIS0002
SIS0002
150
150
140
S1/PE
S1/PE
S1/PE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10L SGZ875/D125 E
CHR16L SGZ875/D125 E
C26L SGZ875/D125 E
SIS0002
SIS0002
SIS0002
178
178
166
S1/PE
S1/PE
S1/PE
20A
25A
125VDC
125VDC
CHR10L SGZ876/D125 E
CHR16L SGZ876/D125 E
SIS0002
SIS0002
205
205
S1/PE
S1/PE
(Refer Pg. 2)
Coil
10a + 10b
• Trip indicator M120
• Lockout Relay V340
D1
12a + 12b
• Trip indicator M120
• Lockout Relay V340
KRAUS & NAIMER BLUE LINE
D2
53
RC/02/2004
"86" Lockout Relay - With Manual Release
Plate
Engraving
64
TRIP
RESET
Contacts
Optional Extras
2a + 2b
• Trip indicator M120
• Lockout Relay V340
4a + 4b
• Trip indicator M120
• Lockout Relay V340
6a + 6b
• Trip indicator M120
• Lockout Relay V340
8a + 8b
• Trip indicator M120
• Lockout Relay V340
10a + 10b
• Trip indicator M120
• Lockout Relay V340
12a + 12b
• Trip indicator M120
• Lockout Relay V340
64
TRIP
RESET
2a + 2b
• Trip indicator M120
• Lockout Relay V340
Electrical
Diagram
TRIP
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
4a + 4b
• Trip indicator M120
• Lockout Relay V340
6a + 6b
• Trip indicator M120
• Lockout Relay V340
KRAUS & NAIMER BLUE LINE
RESET
Coil
D1
D2
Rating
Ith2
Coil
Voltage
Switch
Reference
SIS
Code
20A
25A
40A
24VDC
24VDC
24VDC
CHR10M A721/D024 E
CHR16M A721/D024 E
C26M A721/D024 E
SIS0001
SIS0001
SIS0001
66
66
64
S1/QE
S1/QE
S1a
20A
25A
40A
24VDC
24VDC
24VDC
CHR10M A723/D024 E
CHR16M A723/D024 E
C26M A723/D024 E
SIS0001
SIS0001
SIS0001
94
94
90
S1/QE
S1/QE
S1/QE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10M SGZ873/D024 E
CHR16M SGZ873/D024 E
C26M SGZ873/D024 E
SIS0001
SIS0001
SIS0001
122
122
112
S1/QE
S1/QE
S1/QE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10M SGZ874/D024 E
CHR16M SGZ874/D024 E
C26M SGZ874/D024 E
SIS0001
SIS0001
SIS0001
150
150
140
S1/QE
S1/QE
S1/QE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10M SGZ875/D024 E
CHR16M SGZ875/D024 E
C26M SGZ875/D024 E
SIS0001
SIS0001
SIS0001
178
178
166
S1/QE
S1/QE
S1/QE
20A
25A
24VDC
24VDC
CHR10M SGZ876/D024 E
CHR16M SGZ876/D024 E
SIS0001
SIS0001
205
205
S1/QE
S1/QE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10M A721/D110 E
CHR16M A721/D110 E
C26M A721/D110 E
SIS0001
SIS0001
SIS0001
66
66
64
S1/QE
S1/QE
S1/QE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10M A723/D110 E
CHR16M A723/D110 E
C26M A723/D110 E
SIS0001
SIS0001
SIS0001
94
94
90
S1/QE
S1/QE
S1/QE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10M SGZ873/D110 E
CHR16M SGZ873/D110 E
C26M SGZ873/D110 E
SIS0001
SIS0001
SIS0001
122
122
112
S1/QE
S1/QE
S1/QE
54
Handle
(Black)
Switch
Depth( mm)
Dimension
(Refer Pg. 2)
RC/02/2004
"86" Lockout Relay - With Manual Release
Plate
Engraving
64
TRIP
RESET
Contacts
Optional Extras
8a + 8b
• Trip indicator M120
• Lockout Relay V340
10a + 10b
• Trip indicator M120
• Lockout Relay V340
12a + 12b
• Trip indicator M120
• Lockout Relay V340
64
TRIP
RESET
2a + 2b
• Trip indicator M120
• Lockout Relay V340
4a + 4b
• Trip indicator M120
• Lockout Relay V340
6a + 6b
• Trip indicator M120
• Lockout Relay V340
8a + 8b
• Trip indicator M120
• Lockout Relay V340
Electrical
Diagram
TRIP
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
10a + 10b
• Trip indicator M120
• Lockout Relay V340
12a + 12b
• Trip indicator M120
• Lockout Relay V340
KRAUS & NAIMER BLUE LINE
RESET
Coil
D1
D2
Rating
Ith2
Coil
Voltage
Switch
Reference
SIS
Code
20A
25A
40A
110VDC
110VDC
110VDC
CHR10M SGZ874/D110 E
CHR16M SGZ874/D110 E
C26M SGZ874/D110 E
SIS0001
SIS0001
SIS0001
150
150
140
S1/QE
S1/QE
S1/QE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10M SGZ875/D110 E
CHR16M SGZ875/D110 E
C26M SGZ875/D110 E
SIS0001
SIS0001
SIS0001
178
178
166
S1/QE
S1/QE
S1/QE
20A
25A
110VDC
110VDC
CHR10M SGZ876/D110 E
CHR16M SGZ876/D110 E
SIS0001
SIS0001
205
205
S1/QE
S1/QE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10M A721/D125 E
CHR16M A721/D125 E
C26M A721/D125 E
SIS0001
SIS0001
SIS0001
66
66
64
S1/QE
S1/QE
S1/QE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10M A723/D125 E
CHR16M A723/D125 E
C26M A723/D125 E
SIS0001
SIS0001
SIS0001
94
94
90
S1/QE
S1/QE
S1/QE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10M SGZ873/D125 E
CHR16M SGZ873/D125 E
C26M SGZ873/D125 E
SIS0001
SIS0001
SIS0001
122
122
112
S1/QE
S1/QE
S1/QE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10M SGZ874/D125 E
CHR16M SGZ874/D125 E
C26M SGZ874/D125 E
SIS0001
SIS0001
SIS0001
150
150
140
S1/QE
S1/QE
S1/QE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10M SGZ875/D125 E
CHR16M SGZ875/D125 E
C26M SGZ875/D125 E
SIS0001
SIS0001
SIS0001
178
178
166
S1/QE
S1/QE
S1/QE
20A
25A
125VDC
125VDC
CHR10M SGZ876/D125 E
CHR16M SGZ876/D125 E
SIS0001
SIS0001
205
205
S1/QE
S1/QE
55
Handle
(Black)
Switch
Dimension
Depth (mm) (Refer Pg. 2)
RC/02/2004
"86" Lockout Relay - With Manual Release
Plate
Engraving
64
TRIP
CLOSE
Contacts
Optional Extras
2a + 2b
• Trip indicator M120
• Lockout Relay V340
4a + 4b
• Trip indicator M120
• Lockout Relay V340
6a + 6b
• Trip indicator M120
• Lockout Relay V340
8a + 8b
• Trip indicator M120
• Lockout Relay V340
10a + 10b
• Trip indicator M120
• Lockout Relay V340
12a + 12b
• Trip indicator M120
• Lockout Relay V340
64
TRIP
CLOSE
2a + 2b
• Trip indicator M120
• Lockout Relay V340
Electrical
Diagram
TRIP
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
4a + 4b
• Trip indicator M120
• Lockout Relay V340
6a + 6b
• Trip indicator M120
• Lockout Relay V340
KRAUS & NAIMER BLUE LINE
CLOSE
Coil
D1
D2
Rating
Ith2
Coil
Voltage
Switch
Reference
SIS
Code
20A
25A
40A
24VDC
24VDC
24VDC
CHR10M A721/D024 E
CHR16M A721/D024 E
C26M A721/D024 E
SIS0002
SIS0002
SIS0002
66
66
64
S1/QE
S1/QE
S1/QE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10M A723/D024 E
CHR16M A723/D024 E
C26M A723/D024 E
SIS0002
SIS0002
SIS0002
94
94
90
S1/QE
S1/QE
S1/QE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10M SGZ873/D024 E
CHR16M SGZ873/D024 E
C26M SGZ874/D024 E
SIS0002
SIS0002
SIS0002
122
122
112
S1/QE
S1/QE
S1/QE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10M SGZ874/D024 E
CHR16M SGZ874/D024 E
C26M SGZ874/D024 E
SIS0002
SIS0002
SIS0002
150
150
140
S1/QE
S1/QE
S1/QE
20A
25A
40A
24VDC
24VDC
24VDC
CHR10M SGZ875/D024 E
CHR16M SGZ875/D024 E
C26M SGZ875/D024 E
SIS0002
SIS0002
SIS0002
178
178
166
S1/QE
S1/QE
S1/QE
20A
25A
24VDC
24VDC
CHR10M SGZ876/D024 E
CHR16M SGZ876/D024 E
SIS0002
SIS0002
205
205
S1/QE
S1/QE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10M A721/D110 E
CHR16M A721/D110 E
C26M A721/D110 E
SIS0002
SIS0002
SIS0002
66
66
65
S1/QE
S1/QE
S1/QE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10M A723/D110 E
CHR16M A723/D110 E
C26M A723/D110 E
SIS0002
SIS0002
SIS0002
94
94
90
S1/QE
S1/QE
S1/QE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10M SGZ873/D110 E
CHR16M SGZ873/D110 E
C26M SGZ873/D110 E
SIS0002
SIS0002
SIS0002
122
122
112
S1/QE
S1/QE
S1/QE
56
Handle
(Black)
Switch
Depth( mm )
Dimension
(Refer Pg. 2)
RC/02/2004
"86" Lockout Relay - With Manual Release
Plate
Engraving
64
TRIP
CLOSE
Contacts
Optional Extras
8a + 8b
• Trip indicator M120
• Lockout Relay V340
10a + 10b
• Trip indicator M120
• Lockout Relay V340
12a + 12b
• Trip indicator M120
• Lockout Relay V340
64
TRIP
CLOSE
2a + 2b
• Trip indicator M120
• Lockout Relay V340
4a + 4b
• Trip indicator M120
• Lockout Relay V340
6a + 6b
• Trip indicator M120
• Lockout Relay V340
8a + 8b
• Trip indicator M120
• Lockout Relay V340
Electrical
Diagram
TRIP
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
Coil
10a + 10b
• Trip indicator M120
• Lockout Relay V340
D1
12a + 12b
• Trip indicator M120
• Lockout Relay V340
KRAUS & NAIMER BLUE LINE
CLOSE
Rating
Ith2
Coil
Voltage
Switch
Reference
SIS
Code
Handle
(Black)
Switch
Depth( mm )
Dimension
20A
25A
40A
110VDC
110VDC
110VDC
CHR10M SGZ874/D110 E
CHR16M SGZ874/D110 E
C26M SGZ874/D110 E
SIS0002
SIS0002
SIS0002
150
150
140
S1/QE
S1/QE
S1/QE
20A
25A
40A
110VDC
110VDC
110VDC
CHR10M SGZ875/D110 E
CHR16M SGZ875/D110 E
C26M SGZ875/D110 E
SIS0002
SIS0002
SIS0002
178
178
166
S1/QE
S1/QE
S1/QE
20A
25A
110VDC
110VDC
CHR10M SGZ876/D110 E
CHR16M SGZ876/D110 E
SIS0002
SIS0002
205
205
S1/QE
S1/QE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10M A721/D125 E
CHR16M A721/D125 E
C26M A721/D125 E
SIS0002
SIS0002
SIS0002
66
66
64
S1/QE
S1/QE
S1/QE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10M A723/D125 E
CHR16M A723/D125 E
C26M A723/D125 E
SIS0002
SIS0002
SIS0002
94
94
90
S1/QE
S1/QE
S1/QE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10M SGZ873/D125 E
CHR16M SGZ873/D125 E
C26M SGZ873/D125 E
SIS0002
SIS0002
SIS0002
122
122
112
S1/QE
S1/QE
S1/QE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10M SGZ874/D125 E
CHR16M SGZ874/D125 E
C26M SGZ874/D125 E
SIS0002
SIS0002
SIS0002
150
150
140
S1/QE
S1/QE
S1/QE
20A
25A
40A
125VDC
125VDC
125VDC
CHR10M SGZ875/D125 E
CHR16M SGZ875/D125 E
C26M SGZ875/D125 E
SIS0002
SIS0002
SIS0002
178
178
166
S1/QE
S1/QE
S1/QE
20A
25A
125VDC
125VDC
CHR10M SGZ876/D125 E
CHR16M SGZ876/D125 E
SIS0002
SIS0002
205
205
S1/QE
S1/QE
(Refer Pg. 2)
D2
57
RC/02/2004
"AS" Ammeter Switch
Plate
Engraving
Type of
Metering Switch
Electrical
Diagram
R
AMMETER
OFF
79
OFF
Ammeter Switch
• 4 positions
• 2 CT
• Monitor phase current
64
T
T
R
R
Switch
Reference
20A
25A
40A
6A
CHR10
CHR16
C26
CAD11
20A
25A
40A
6A
CHR10 A048/SGZ878*EG
CHR16 A048/SGZ878*EG
C26
A048/SGZ878E
CAD11 A048/SGZ878*EG
20A
25A
40A
6A
CHR10
CHR16
C26
CAD11
20A
25A
40A
6A
CHR10
CHR16
C26
CAD11
20A
25A
40A
6A
CHR10
CHR16
C26
CAD11
SIS
Code
Handle
(Black)
Dimension
(Refer Pg. 2)
T
1
3
6
8
5
7
OFF
Ammeter Switch
• 4 positions
• 3 CT
• Monitor phase current
S
S
2
4
S
T
R
Rating
Ith2
R
S
A
-
S1/PR
S1/PR
S1/PR
S1/PR
-
S1/PR
S1/PR
S1/PR
S1/PR
SGZ879EG
SGZ879EG
SGZ879E
SGZ879EG
SIS0001
SIS0001
SIS0001
SIS0001
S1/PR
S1/PR
S1/PR
S1/PR
SGZ880EG
SGZ880EG
SGZ880E
SGZ880EG
SIS0001
SIS0001
SIS0001
SIS0001
S1/PR
S1/PR
S1/PR
S1/PR
SIS0001
SIS0001
SIS0001
SIS0001
S1/PR
S1/PR
S1/PR
S1/PR
A021/SGZ877*EG
A021/SGZ877*EG
A021/SGZ877E
A021/SGZ877*EG
T
2
4
1
3
6
8
10
12
5
7
9
A
11
64
Ammeter Switch
• 4 positions
• 3 CT
• Monitor phase current
AMMETER
79
R
S
OFF
S
OFF
T
AMMETER
R
S
OFF
T
Ammeter Switch
• 5 positions
• 3 CT
• Monitor phase &
neutral current
1
2
3
2
4
6
8
10
12
T
64
79
R
R
S
1
3
5
7
9
11
OFF
T
R
S
T
A
N
2
4
6
8
10
12
1
3
5
7
9
11
A
N
OFF
Ammeter Switch
• 5 positions
A
+
KRAUS & NAIMER BLUE LINE
R
S
T
N
2
4
6
8
10
12
1
3
5
7
9
11
R
14
16
13
15
N
58
S
T
SGZ881EG
SGZ881EG
SGZ881E
SGZ881EG
RC/02/2004
"AS" Ammeter Switch
Plate
Engraving
Type of
Metering Switch
Electrical
Diagram
R
S
T
OFF
Ammeter Switch
• 4 positions
• 2 CT
• 3 phase 3 wire
R
S
Rating
Ith2
Switch
Reference
SIS
Code
20A
25A
CHR10 SGZ891EG
CHR16 SGZ891EG
SIS0001
SIS0001
S1/PE
S1/PE
20A
25A
CHR10
CHR16
SGZ892EG
SGZ892EG
SIS0001
SIS0001
S1/PE
S1/PE
20A
25A
CHR10
CHR16
SGZ893EG
SGZ893EG
SIS0001
SIS0001
S1/PE
S1/PE
20A
25A
CHR10
CHR16
SGZ894EG
SGZ894EG
SIS0001
SIS0001
S1/PE
S1/PE
T
1
2
3
5
7
4
6
8
A
Handle
(Black)
Dimension
(Refer Pg. 2)
64
AMMETER
S
79
R
T
Ammeter Switch
• 4 positions
• 2 CT with transducer
• 3 phase 3 wire
OFF
OFF
R
S
R
S
T
S
A
1
3
2
4
5
7
9
11
13
15
17
6
8
10
12
14
16
18
OFF
T
Ammeter Switch
• 4 positions
• 3 CT
• 3 phase 3 wire
64
R
T
R
S
T
R
T
1
3
5
7
9
2
4
6
8
10
11
12
A
AMMETER
79
OFF
T
R
R
S
T
OFF
S
Ammeter Switch
• 4 positions
• 3 CT with transducer
• 3 phase 3 wire
KRAUS & NAIMER BLUE LINE
R
S
T
A
1
3
2
4
5
7
6
8
9
11
13
15
17
10
12
14
16
18
59
T
S R
RC/02/2004
"AS" Ammeter Switch
Plate
Engraving
Type of
Metering Switch
64
Electrical
Diagram
R
S
OFF
T
AMMETER
S
R
79
T
OFF
OFF
64
AMMETER
S
79
R
T
Ammeter Switch
• 4 positions
• 3 CT
• 3 phase 3 wire
Ammeter Switch
• 4 positions
• 3 CT
• 3 phase 4 wire
OFF
KRAUS & NAIMER BLUE LINE
R
S
T
R
S
T
2
3
4
5
6
7
8
9
10
11
12
OFF
R
S
Switch
Reference
SIS
Code
Handle
(Black)
Dimension
20A
25A
CHR10 SGZ895EG
CHR16 SGZ895EG
SIS0001
SIS0001
S1/PE
S1/PE
20A
25A
CHR10
CHR16
SIS0001
SIS0001
S1/PE
S1/PE
(Refer Pg. 2)
OFF
1
N
Rating
Ith2
A
T
1
2
3
4
5
6
7
8
9
10
11
12
60
SGZ896EG
SGZ896EG
A
RC/02/2004
" VS " Voltmeter Switch
Plate
Engraving
Type of
Metering Switch
Electrical
Diagram
Voltmeter Switch
• 4 positions
• Phase to phase voltage
64
VOLTMETER
OFF
OFF
RS ST
TR
1
2
3
4
T
5
6
S
7
8
R
79
TR
Rating
Ith2
Switch
Reference
SIS
Code
Handle
(Black)
20A
25A
40A
CHR10 SGZ882EG
CHR16 SGZ882EG
C26
SGZ882E
SIS0001
SIS0001
SIS0001
S1/PR
S1/PR
S1/PR
20A
25A
40A
CHR10 SGZ884EG
CHR16 SGZ884EG
C26
SGZ884E
SIS0001
SIS0001
SIS0001
S1/PR
S1/PR
S1/PR
20A
25A
6A
40A
CHR10
CHR16
CAD11
C26
SIS0001
SIS0001
SIS0001
SIS0001
S1/PR
S1/PR
S1/PR
S1/PR
Dimension
(Refer Pg. 2)
V
RS
ST
64
VOLTMETER
OFF
RS
RN
79
ST
Voltmeter Switch
• 7 positions
• Phase to phase and
phase to neutral voltage
TR
V
64
VOLTMETER
OFF
RN
79
ST
SN
TR
2
3
4
5
6
7
8
9
10
R
11
12
N
S
TN
RS
1
T
SN
TR
ST RSOFF RN SN TN
Voltmeter Switch
• 8 positions
• Phase to phase and
phase to neutral voltage
through transducers
TN
OFF
OFF
OFF
TR
SN
TN
RN
RS
-+
1
2
TR
-+
3
4
5
6
SN
-+
7
8
9
10
11
12
13
14
15
16
17
18
-+
19
20
RN
-+
21
22
23
24
ST
-+
TN
KRAUS & NAIMER BLUE LINE
ST
RS
61
SGZ885EG
SGZ885EG
SGZ885EG
SGZ885E
V
RC/02/2004
" VS " Voltmeter Switch
Plate
Engraving
Type of
Metering Switch
Electrical
Diagram
R ST
Voltmeter Switch
• 4 positions
• Phase to phase voltage
via 2 PT
• 3 phase 3 wire system
OFF
RS
ST
TR
1
3
2
5
7
6
V
Rating
Ith2
Switch
Reference
SIS
Code
Handle
(Black)
20A
25A
CHR10 SGZ886EG
CHR16 SGZ886EG
SIS0001
SIS0001
S1/PE
S1/PE
20A
25A
CHR10 SGZ887EG
CHR16 SGZ887EG
SIS0001
SIS0001
S1/PE
S1/PE
20A
25A
CHR10 SGZ888EG
CHR16 SGZ888EG
SIS0001
SIS0001
S1/PE
S1/PE
20A
25A
CHR10 SGZ889EG
CHR16 SGZ889EG
SIS0001
SIS0001
S1/PE
S1/PE
20A
25A
CHR10 A007/SGZ890*EG
CHR16 A007/SGZ890*EG
Dimension
(Refer Pg. 2)
4
8
64
VOLTMETER
ST
79
RS
TR
OFF
Voltmeter Switch
• 4 positions
• Phase to phase voltage
via 3 PT
• 3 phase 3 wire system
Voltmeter Switch
• 4 positions
• Phase to neutral voltage
via 3 PT
• 3 phase 4 wire system
R S T
OFF
RS
ST
TR
1
3
2
4
5
7
6
V
8
R S T N
OFF RN
SN
TN
1
2
3
4
5
6
7
8
V
64
VOLTMETER
ST
79
RS
TR
OFF
OFF
R S T
Voltmeter Switch
• 5 positions
• Phase tophase voltage
via 3 PT
• 3 phase 3 wire system
OFF RS
ST
TR OFF
1
2
4
3
5
V
6
7
8
64
VOLTMETER
OFF
RN
79
RS
ST
SN
TR
Voltmeter Switch
• 7 positions
• Phase tophase and
Phase to neutral voltage
• 3 phase 4 wire system
TN
KRAUS & NAIMER BLUE LINE
R
S
T
N
TR
ST
RS
OFF RN
SN
TN
2
4
6
8
10
12
1
3
5
7
9
11
62
-
S1/PE
S1/PE
V
RC/02/2004
" VS + AS " Voltmeter /Ammeter Switch
Plate
Engraving
Type of
Metering Switch
Electrical
Diagram
R
S
PT
T
T-R
64
OFF
S
S-T
Switch
Reference
SIS
Code
20A
25A
CHR10 SGZ890EG
CHR16 SGZ890EG
SIS0001
SIS0001
Handle
(Black)
Dimension
(Refer Pg. 2)
T
64
R
R-S
Rating
Ith2
Voltmeter/Ammeter
• 4 positions
• Phase to phase voltage
via 3 PT
• 3 CT
• 3 phase 3 wire system
OFF
R
RS
S
ST
T
TR
1
3
2
5
6
7
8
9
11
10
13
14
15
16
17
18
19
20
4
12
V
S1/PE
S1/PE
A
CT
KRAUS & NAIMER BLUE LINE
63
RC/02/2004
DISCREPANCY SWITCH
mimic panel and the actual field condition exists.
c. To TRIP the circuit breaker ( to close the tripping circuit of the breaker ) at position
"A", it is necessary to Push-in and Turn the handle to position "AB". The handle will spring
return back to position "A " when release. The double action of Push-in and Turn is a
safety precaution to prevent
accidental operation of the Discrepancy Switch. Auxiliary contacts which operates when
the handle is Push-in can be incorporated for additional safety circuits.
d. To "CLOSE" the circuit breaker ( to activate the closing circuit of the breaker) at
position "E", it is necessary to Push-in and Turn the handle to position "EB". The handle
will spring return back to position "E" when release. The double action of Push-in and
Turn is a safety precaution to prevent accidental operation of the Discrepancy Switch.
Auxiliary contacts which operates when the handle is Push-in can be incorporated for
additional safety circuits ( for Size S0 and S1 switch only )
A
AB
APPLICATION
The Discrepancy Switch allows operation of the circuit breakers remotely from the
control room. An illuminated handle on the discrepancy switch mounted on the mimic panel
would shows the discrepancy between what is shown on the mimic diagram and the real
condition of the circuit breaker. In the normal condition, none of the panel lights would light
up.
Circuit breakers are controlled by a negative lighting system. Hence when the lamp is
lighted " ON", means there is a discrepancy between what is indicated in the control room
and the actual field condition of the circuit breaker.
From the above requirement, a large number of push-buttons, selector switches and
pilot lamps would normally be required to fulfil the control functions. A discrepancy switch
with multi-function can combine all these requirements in a single cam switch.
E
EB
Fig. 1 - Principle of operation
PRINCIPLE OF OPERATION - Fig. 1
A typical Discrepancy Switch would have four positions AB, A, E and EB. Position
A and B are stay-put positions.
To turn from position A to AB, it is necessary to Push-in at position A and then turn to
position AB. Handle will spring-return back to position A when release. Similarly for
positions E and EB. Mechanical interlocks will prevent turning of the handle from A to B
when handle is Push-in.
The switch would operated at two levels:
a. The handle can be Turn from A to B to give a semaphore indication in the mimic panel.
b. The handle will light up whenever any discrepancies between the condition on the
KRAUS & NAIMER BLUE LINE
64
RC/02/2004
DISCREPANCY SWITCH
2.
TYPES OF DISCREPANCY SWITCH
Kraus & Naimer discrepancy switch are available in the following sizes:
a.
Size S00 - for switch rating up to 10A. These switches are commonly used in
mimic and mosaic panels. Low voltage switches of gold contact ( Type CA4-1 ) are
available for electronics and thermocouple circuits.
AB
A
b.
Size S0 - for switch rating from 16A to 32A/AC21. These switches are commonly
used in mimic and mosaic panels. Low voltage switches of silver H- Bridge contact ( type
CAD12 ) or gold H-Bridge contact ( type CAD11) are available for electronics and
thermocouple circuits.
l
ve
Le
n
-i
sh
Pu
c.
Size S1 - for switch rating of 20A to 63A AC21. These switches are especially
suitable for switching highly inductive loads e.g. circuit breaker coils etc.
el
ev
L
al
rm
No
EB
E
Fig. 2 - Handle movement
1.
FEATURES OF DISCREPANCY SWITCH
a.
Ratings available:
• Size S00 - 10A
• Size S0 - 16A to 32A AC21
• Size S1 - 20A to 63A AC21.
b. The lighting system is placed directly behind a translucent handle and consist of lamps
connected in series/parallel network as follows:
• Size S00 consist of a single lamp
• Size S0 consist of 4 lamps with rating of 1.2W each.
• Size S1 consist of 6 lamps with rating of 1.2W each.
The advantage of having more than one lamp is that should one lamp fails, the other
lamps connected in the parallel network still operates but with reduced illumination in case
a discrepancy condition occurs.
c. Auxiliary push-button contacts can be operated which operates when the handle is
Push-in ( S0 AND S1 only )
d. Residual or slip-clutch contact can be incorporated on request ( S0 and S1 only ).
KRAUS & NAIMER BLUE LINE
65
RC/02/2004
DISCREPANCY SWITCH FOR MOSIAC Mounting - Size S00
3.
DISCREPANCY SWITCH for Mosaic Panel Mounting - Size S00
Mosiac Grid
Lock nut
Lamp
25
Adaptor
Lamp
holder
Lamp
terminals
25
Fig. 4c- Rear mounting
Fig. 4d- Front mounting by lock nut/adaptor on mosaic grid
Fig. 4a - M24/M25 Mounting
a.
General information.
Mosiac
tile
Type M 24 and M25 mountings are designed for used on mosaic panel with
• 24 x 24mm tiles - Type M24
• 25 x 25mm tiles - Type M25
The switch is slot in between the grids of the mosaic panel and mounted on the
grids and clamp on to the grids by means of the hexagonal nut from the front. Access to
the lamp is by removing the illuminated handle.
12 ø
Fig. 4e- Tile mounting hole
Mosiac aluminium grid
Cast alumnium casing
mounted on grid
b.
Switch
Fig. 4f - Handle mounted on tile.
Switch Ratings
The switch contacts operate when the handle is turn. The switches are suitable for
both AC and DC switching . Type CA4-1 with gold contacts are specially suitable for :
• Low voltage switching of electronics and thermocouple circuits due to it's low
contact resistance.
• Corrosive environment where the gold contact prevent oxidation of the contact
surface which can increases contact resistance.
In selecting the switch model for DC switching, the selection of appropriate switch
depends on:
• The DC supply voltage
• The DC load current
• The type of load - resistive/inductive
In selecting the switch model for low voltage switching, the Dry Circuit Rating
should not be exceeded. The Dry Circuit Rating refers to the relationship between the
supply voltage and load current. If the value exceeds, arcing may occur which would
remove the layer of gold on the contact.
Handle
L2
L1
Lamp
Translucent
handle
Mosiac
tile
Lamp terminals
Fig. 4b- Constructional details of M24 and M25 mounting
KRAUS & NAIMER BLUE LINE
66
RC/02/2004
DISCREPANCY SWITCH for MOSIAC Mounting - Size S00
AC Switching Capacity
c.
Switch Type
CG4
Nominal Voltage
V
500
Nominal Current
• AC21
• AC23/415V
A
kW
10
2.2
Lighting System for mounting Type M24 and M25
A single lamp is mounted directly below the translucent handle. The lamp used may be
either filament lamp ( Type T5.5K ) or LED which is available in red, yellow and green
colour. Maximum voltage possible is 60V for filament and 24V for LED.
i. Filament Lamp
Supply Voltage
Lamp Rating
Lamp Reference
0.75 W
0.75 W
0.75 W
0.75 W
0.75 W
0.75 W
999 T5.5K/6V
999 T5.5K/12V
999 T5.5K/24V
999 T5.5K/36V
999 T5.5K/48V
999 T5.5K/60V
Fig. 6d- AC Switching Capacity
6V
12V
24V
36V
48V
60V
DC Switching Capacity DC1 T = 1 mS Resistive Load
Number .of Series Contact
1
2
3
4
CG4
24V
48V
60V
10A
6A
2.5A
48V
95V
120V
95V
140V
180V
120V
190V
240V
ii. LED Lamp
Fig. 6e - DC Switching Capacity - resistive load
DC Switching Capacity T = 50 mS Inductive Load
Number of Series Contact
1
2
3
4
24V
48V
60V
48V
95V
120V
95V
140V
180V
Supply Voltage
Yellow LED
Red LED
Green LED
24V
LE-6-T5.5Y
LE-6-T5.5R
LE-6-T5.5G
CG4
120V
190V
240V
6A
3A
1A
Fig. 6f - DC Switching Capacity - inductive load
Dry Circuit Rating CG4-1
AC1
1V
6V
12V
24V
48V
60V
120V
1A
0.6A
0.45A
0.3A
0.22A
0.2A
0.15A
Fig. 6g - Dry Circuit Rating
Maximum Number of Contacts Possible
Switch Type
CG4
Maximum Contacts
8
KRAUS & NAIMER BLUE LINE
Maximum Stages
4
67
RC/02/2004
DISCREPANCY SWITCH for MOSIAC Mounting - SIZE S0
4. DISCREPANCY SWITCH for Mosaic Mounting - Size S0
75
50
75
50
Fig. 7 Mounting on 50x50mm mosaic tile
a.
General Information
The Type M50 mounting is design for mounting Size S0 discrepancy switch on mosaic
tiles with the following dimensions:
• 50 x 50mm
• 75 x 75mm
The switch is screwed on the to the aluminium grid of the mosaic panel from the rear as
well as well as held by two screws from the front via the mosaic tile and clamp ring ( Refer
Fig. 9). The translucent handle is screwed on to the aluminium shaft which operates the
auxiliary contacts when the handle is Push-in and the switch contacts when the handle is
turned. Removal of the handle from the shaft allows access to the lamps from the front of
the panel.
Fig. 8 - Mounting on 75x75 mosaic tile
Mosiac aluminium grid
Mosiac tile
Fig. 9 - Type M50 mounting method
Translucent
Handle
Lamp
Holder
Clamping
Disk
Switch Contacts Turn to Operate
Clamp
Disk
Translucent
Handle
30.5 ø
Escutcheon
Plate
Switch
Shaft
Lamps
Push to Operate
Interlock & Auxillary
Contacts
Clamp Disk screwed
to mosiac tile
Residual Contact
( Optional )
Fig. 10a - Mounting hole
on mosaic tile
Fig 6 - Type M50 Mounting
KRAUS & NAIMER BLUE LINE
68
Fig. 10b - Switch front
by two screws
Mosiac
Tile
Fig10c - Final mounting
on mosaic tile.
RC/02/2004
DISCREPANCY SWITCH for MOSIAC Mounting - Size S0
Lamp
holder
voltage, the lamps can be connected in series/parallel circuit. ( Fig. 7 ) The advantage of
this arrangement is that should any of the lamps fails, other lamps in the parallel circuit will
still lights up to indicate discrepancy reducing the danger of not knowing that there is a
discrepancy fault due to lamp failures.
In addition, high bright LED lamps type LE6.5B are available in T6.8K. Ratings
available for LED/T6.8K are 12VDC/35mA and 24VDC/15mA and available in Red, Yellow
and Green Colour.
Lamps
Switch
shaft
c.
Fig. 11b- M50 Front mounting
6 - 6.5 mm ø
Fig. 11a - M50 Front Mounting
Lamps for S0 Discrepancy Switch
42-44mm
Fig. 13a - Filament lamp type T6.8K
i.
Fig 12a - Type M50 - lamp holder
b.
Fig. 12b - Type M50 rear mounting
Lighting System
60V/1.2W
Supply
Voltage
Lamp
Rating
Lamp
Reference
6V
12V
24V
36V
42V
60V
1.2W
1.2W
1.4W
1.4W
1.4W
1.5W
999
999
999
999
999
999
60V/1.2W
T6.8K/6
T6.8K/12
T6.8K/24
T6.8K/36
T6.8K/42
T6.8K/60
Fig. 13b - Types of filament lamp
ii.
110VDC
Fig. 7- Size S0 Lighting System
The Size S0 lighting system consist of a lamp holder with four socket outlets to
accommodate 4 telephone bulbs type T6.8K Voltages available for the lamps are 6V, 12V,
24V, 30V, 36V, 42V, 48V and 60V of rating 1.2 watts per lamp. Depending on the control
KRAUS & NAIMER BLUE LINE
Filament Lamp
LED Lamp
Voltage
Yellow LED
Red LED
Green LED
12V
24V
LE-6.5B-2Y
LE-6.5B-4Y
LE-6.5B-2R
LE-6.5B-4R
LE-6.5B-2G
LE-6.5B-4G
Fig. 13c - Types of LED
69
RC/02/2004
DISCREPANCY SWITCH for MOSIAC Mounting - SIZE S0
e.
D.
Coding of Lamp holders Q100
Switch Ratings
Kraus & Naimer switches are design for both AC and DC switching. For DC switching,
the selection of suitable switch type depends on:
• The DC Voltage
• The DC Load Current
• The type of Load - resistive or inductive. For rating on DC switching capacity,
please refer to the information on "DC Switching Capacity" for C, CA and A switches
respectively.
It is possible to add residual contacts to give a self-holding effect by adding the
optional extra M200
S0 Q100 / RKD004
e.
Push To Turn Interlocks and Auxiliary Contacts
The auxiliary contacts are rated at 10A and operates when the handle is Push-in. Up to a
maximum of 8 auxiliary contacts are available.
AC Switching Capacity
S0 V130 /
Number of
NO NC
0
0
1
0
0
1
1
1
2
0
0
2
2
2
3
1
1
3
4
0
0
4
3
3
4
2
6
0
4
4
6
2
8
0
F 11 / 6 A - EL
Switch Size
S0
S0
Auxillary Contacts
Contacts
without contacts
1 contact
1 contact
2 contact
2 contact
2 contact
4 contact
4 contact
4 contact
4 contact
4 contact
6 contact
6 contact
6 contact
8 contact
8 contact
8 contact
Type
CHR10
CHR16
Rating/Ith2
20A
25A
Fig. 14 - Auxiliary contacts combination
KRAUS & NAIMER BLUE LINE
70
RC/02/2004
DISCREPANCY SWITCH for PANEL Mounting - SIZE S0
5. DISCREPANCY SWITCH FOR PANEL MOUNTING - SIZE S0
•
•
Low voltage switches of silver contact ( Type CAD12 ) or gold contact ( Type
CAD11) for electronics and thermocouple circuits.
For power switching of highly inductive loads e.g. circuit breaker coils .
Dø
The types of mounting available are:
Fig. 15a - Type FT1 Panel Mounting for switch Size S0
D = 37.5mm ø
Fig. 16a - FT1 Mounting
i.
Type FT1Mounting ( Fig. 15a and Fig 16a. )
The front escutcheon is a black ring . A black escutcheon plate can be provided
on request.
A
Fig. 15b - Type FT2 Panel Mounting for switch Size S0
Translucent
handle
Lamp
Lamp
Terminal
Auxillary
Contacts
Switch
Contacts
A
Dismantling Tool SOE Q110 09
( To remove Q110 switch body from handle)
Fig 16b - FT2 Mounting
Fig. 15c - Type FT1/FT2 Mounting for Size S0 switch constructional details
ii. Type FT2 Mounting ( Fig. 15b and Fig. 16b )
A square escutcheon plate 48 x 48 mm is provided which allows engravings.
a. Size S0 Discrepancy switches for mounting on panels and mimic are available for
switch of ratings up to 32A and are suitable for:
KRAUS & NAIMER BLUE LINE
71
RC/02/2004
DISCREPANCY SWITCH for PANEL Mounting - SIZE S0
iii. Type FH3 Mounting ( Fig. 16b )
Similar to Type FT2 except the escutcheon plate size is 64 x 64mm.
h.
Kraus & Naimer switches are design for both AC and DC switching. For DC
switching, the selection of suitable switch type depends on:
• The DC Voltage
• The DC Load Current
• The type of Load - resistive or inductive. For rating on DC switching capacity,
please refer to the information on "DC Switching Capacity" for C, CA and A
switches respectively.
It is possible to add residual contacts to give a self-holding effect by
adding the slip clutch optional extra M200
b. Handle
The translucent handle is screwed on to the aluminium shaft which operates the auxiliary
contacts when the handle is Push-in and the switch contacts when the handle is turned.
Removal of the handle from the shaft allows access to the lamps from the front of the panel
c.
Mounting System
The switch is mounted on to the panel by means of a single hole mounting 30mm Ø with
locking nut.( Fig. 15c )
d.
Switch Ratings
i.
AC Switching Capacity
Switch Size
S0
S0
S0
S0
S0
Lighting System
The Size S0 lighting system consist of a lamp holder with a socket outlets to accommodate one lamp of Type BA9 base Voltages available for the lamps are 6V, 12V, 24V,30V
and 130V
In addition, high bright LED lamps type are available . Ratings available for LED are
6V, 12V, 24V, 110V and 220VDC.
Type
CA10
CA20
CA25
CHR10
CHR16
Rating/Ith2
20A
25A
32A
20A
25A
e.
Auxiliary Contacts
The auxiliary contacts are rated at 10A and operates when the handle is Push-in. Up to a
maximum of 2 auxiliary contacts are available. The type of contacts available are:
• Standard silver contacts
• Gold contacts for corrosive environments
• Gold H-Bridge contacts for low voltage application
f.
Dismantling Tool SOE Q110 09
To separate the switch body ( consisting of the switch stage, auxillary contacts and the
lighting system) from the handle/mounting system, a dismantling tool is available. This tool is
especially suitable :
• When mounting the switch body to the mounting system.
• When removing the switch body from the mounting system for the purpose of
removing/changing the lamp from the lamp holder.
g. LampRemover 999 LZ8
This tool allow easy removal of the lamp from the lamp holder
KRAUS & NAIMER BLUE LINE
72
RC/02/2004
DISCREPANCY SWITCH for PANEL Mounting - SIZE S0/S1
b. Handle
The translucent handle is screwed on to the aluminium shaft which operates the
auxiliary contacts when the handle is Push-in and the switch contacts when the handle is
turned. Removal of the handle from the shaft allows access to the lamps from the front of
the panel
\
6. DISCREPANCY SWITCH FOR PANEL MOUNTING - SIZE S0/S1
c.
Clamping System
Fig. 17a - Type EL Panel Mounting for switch Size S0
Fig. 18 - Handle and clamping system
The switch is mounted on to the panel by means of a clamping system which consist
of the clamping disk, pressing ring and the lamp-holder. Mounting and tightening of the
switch to the panel is by means of the four screws fitted on the lamp holder ( Fig. 18) .
d.
Lighting System
60V/1.2W
Clamping
Disk
Front
Plate
Push to
Operate
Interlock &
Auxillary
Contacts
Switch
Contacts Turn to
Operate
Residual
Contact
( Optional )
6 - 6.5 mm ø
Translucent
Handle
Lamp
Holder
Fig. 17b - Type EL Mounting for Size S0 switch constructional details
a. Size S0 Discrepancy switches with large Size S1 handles for mounting on panels and
mimic are available for switch of ratings up to 32A and suitable for
• Low voltage switches of silver contact ( Type CAD12 ) or gold contact ( Type CAD11) for
electronics and thermocouple circuits.
• For power switching of highly inductive loads e.g. circuit breaker coils etc.
KRAUS & NAIMER BLUE LINE
60V/1.2W
42-44mm
110VDC
Fig. 19a - Filament lamp type T6.8K
Fig. 19b- Size S0 Lighting System
The Size S1 lighting system consist of a lamp holder with four socket outlets to
accommodate 4 telephone bulbs type T6.8K ( Fig 19a ) Voltages available for the lamps
73
RC/02/2004
DISCREPANCY SWITCH for PANEL Mounting - SIZE S0/S1
are 6V, 12V, 24V, 30V, 36V, 42V, 48V and 60V of rating 1.2 watts per lamp. Depending on
the control voltage, the lamps can be connected in series/parallel circuit. ( Fig. 19b ) The
advantage of this arrangement is that should any of the lamps fails, other lamps in the
parallel circuit will still lights up to indicate discrepancy reducing the danger of not knowing
that there is a discrepancy fault due to lamp failures.
In addition, high bright LED lamps type LE6.5B are available in T6.8K. Ratings
available for LED/T6.8K are 12VDC/35mA and 24VDC/15mA and available in Red, Yellow
and Green Colour.
e.
• The DC Load Current
• The type of Load - resistive or inductive. For rating on DC switching capacity, please
refer to the information on "DC Switching Capacity" for C, CA and A switches respectively.
It is possible to add residual contacts to give a self-holding effect by adding the
optional extra M200
i.
AC Switching Capacity
Switch Size
S0
S0
S0
S0
Coding of Lamp holders Q100
S0 Q100 / RKD001
Type
CA10
CA20
CHR10
CHR16
Rating/Ith2
20A
25A
20A
25A
Maximum Number of Stages
5
4
4
4
f.
Push to Turn Interlock and Auxiliary Contacts
The auxiliary contacts are rated at 10A and operates when the handle is Push-in. Up to a
maximum of 8 auxiliary contacts are available.
S0 V130 /
Number of
NO NC
0
0
1
0
0
1
1
1
2
0
0
2
2
2
3
1
1
3
4
0
0
4
3
3
4
2
6
0
4
4
6
2
8
0
e.
F 11 / 6 A - EL
Auxillary Contacts
Contacts
without contacts
1 contact
1 contact
2 contact
2 contact
2 contact
4 contact
4 contact
4 contact
4 contact
4 contact
6 contact
6 contact
6 contact
8 contact
8 contact
8 contact
Switch Ratings
Kraus & Naimer switches are design for both AC and DC switching. For DC switching,
the selection of suitable switch type depends on:
• The DC Voltage
KRAUS & NAIMER BLUE LINE
74
RC/02/2004
DISCREPANCY SWITCH for PANEL Mounting - SIZE S1
c.
Clamping System
Dø
7. DISCREPANCY SWITCH FOR PANEL MOUNTING - SIZE S1
D = 50mm ø
Fig. 21 - Handle and clamping system
Fig. 20a - Type EL Panel Mounting for switch Size
The switch is mounted on to the panel by means of a clamping system which consist of
the clamping disk, pressing ring and the lamp-holder. Mounting and tightening of the switch to
the panel is by means of the four screws fitted on the lamp holder ( Fig. 17) .
d.
Lighting System
6 - 6.5 mm ø
42V/1.2W
1
Translucent
Handle
Clamping
Disk
Front
Plate
Lamp
Holder
Push to Operate Interlock
& Auxillary Contacts
Switch Contacts Turn to Operate
42V/1.2W
42V/1.2W
42-44mm
110VDC
Residual Contact
( Optional )
Fig. 22a - Filament lamp type T6.8K
Fig. 22b- Size S1 Lighting System
Fig. 20b - Type EL Mounting for Size S1 switch constructional details
The Size S1 lighting system consist of a lamp holder with six socket outlets to
accommodate 6 telephone bulbs type T6.8K( Fig. 22a ) Voltages available for the lamps are
6V, 12V, 24V, 30V, 36V, 42V, 48V and 60V of rating 1.2 watts per lamp. Depending on the
control voltage, the lamps can be connected in series/parallel circuit. ( Fig. 22b ) The advantage of this arrangement is that should any of the lamps fails, other lamps in the parallel
circuit will still lights up to indicate discrepancy reducing the danger of not knowing that there
is a discrepancy fault due to lamp failures.
In addition, high bright LED lamps type LE6.5B are available in T6.8K. Ratings
available for LED/T6.8K are 12VDC/35mA and 24VDC/15mA and available in Red, Yellow
a. Size S1 Discrepancy switches for mounting on panels and mimic are available for switch
of ratings up to 80A and suitable for power switching of highly inductive loads e.g. circuit
breaker coils etc.
b. Handle
The translucent handle is screwed on to the aluminium shaft which operates the auxiliary
contacts when the handle is Push-in and the switch contacts when the handle is turned.
Removal of the handle from the shaft allows access to the lamps from the front of the panel
KRAUS & NAIMER BLUE LINE
75
RC/02/2004
DISCREPANCY SWITCH for PANEL Mounting - SIZE S1
and Green Colour.
e.
Coding of Lamp holders Q100
extra M200
AC Switching Capacity
i.
Switch Size
S1
S1
S1
S1
S1 Q100 / A 2 B
Color of front ring
2 ...
3 ...
Black ( with black aluminium
escutcheon plate
Black ring only
S1
S1
S1
S1
f.
Push to Turn Interlock and Auxiliary Contacts
The auxiliary contacts are rated at 10A and operates when the handle is Push-in. Up to a
maximum of 8 auxiliary contacts are available.
S1 V130 /
Number of
NO NC
0
0
1
0
0
1
1
1
2
0
0
2
2
2
3
1
1
3
4
0
0
4
3
3
4
2
6
0
4
4
6
2
8
0
e.
Type
CA10B
CA20B
CA25B
CHR10B
Rating/Ith2
20A
25A
32A
20A
CHR16B
C26
C32
C42
25A
40A
63A
80A
F 11 / 6 A - EL
Auxillary Contacts
Contacts
without contacts
1 contact
1 contact
2 contact
2 contact
2 contact
4 contact
4 contact
4 contact
4 contact
4 contact
6 contact
6 contact
6 contact
8 contact
8 contact
8 contact
Switch Ratings
Kraus & Naimer switches are design for both AC and DC switching. For DC switching,
the selection of suitable switch type depends on:
• The DC Voltage
• The DC Load Current
• The type of Load - resistive or inductive. For rating on DC switching capacity, please
refer to the information on "DC Switching Capacity" for C, CA and A switches respectively.
It is possible to add residual contacts to give a self-holding effect by adding the optional
KRAUS & NAIMER BLUE LINE
76
RC/02/2004
DISCREPANCY SWITCH for PANEL Mounting
8.
ORDERING PROCEDURE
P
R
ALARM
O
CLOSE condition. The lamp will cut off only when the handle is turn to the TRIP
position . This removes the discrepancy between the mimic diagram and the true
position of the breaker.
Pushing-in and Turning the discrepancy switch handle at the TRIP position will
activates the tripping circuit of the breaker
Push-in and Turning the handle at the 'CLOSE" position will activates the
closing circuit of the breaker.
The switching configuration required is as shown in Fig. 22. Contact rating
required is 25A. Auxiliary contact required is 1 NO + 1 NC . Voltage of the lighting
system is 110V
EB
E
A
1
AB
2
3
4
5
6
7
8
13
14
15
16
Closed contact
Continous contact
Residual contact
N
Fig. 21 - Typical Discrepancy Switch Circuit
Fig. 22 - Required contact configuration
a. Typical Specifications
9.
When the handle of a discrepancy switch is turn 90 degrees, the mimic diagram of
the control panel will immediately indicate any circuit interruptions. The handle of the
discrepancy switch will be illuminated to indicate a discrepancy between the condition
as indicated in the mimic panel and the actual condition of the circuit breaker. For
example, if the circuit breaker and the discrepancy switch handle is in the is in the
"CLOSED" position, the handle will not be illuminated because there is no discrepancy
between what is shown in the mimic panel and the actual condition of the circuit
breaker.
If the circuit breaker TRIP due to a fault condition, the handle of the discrepancy
switch will be illuminated because a discrepancy arise i.e. the handle is still in the
When ordering a Discrepancy Switch, the following are to be provided:
a.
Switch Type selected according to the control voltage, load current and the type of
load. In this case CHR16 would be suitable
b.
The Switching Configuration required ( refer Fig. 22 ). The switch can be given a
special switch reference :
KRAUS & NAIMER BLUE LINE
HOW TO ORDER - Size S0
•
CHR16 SGxxx1
c.
The number of Auxiliary contacts required. In this case 1 NO + 1 NC auxiliary
contact are required. As no engravings are required on the escutcheon plate, FT1
77
RC/02/2004
DISCREPANCY SWITCH for PANEL Mounting
mounting type of lamp holder would be suitable.Hence the coding for the Control & Indicator
Device with TURNING/PUSHING facility Iis as follows:
•
S0
Q110/F11A1
d. The Ordering Code as follows:
Reference
Description
CHR16 SGxxx1
Switch
S0 Q110/F11A1
Control & Indicator device with single hole FT! mounting
Operation by TURNING/PUSHING
999 BA9/130V
130V Filament Lamp
10.
HOW TO ORDER - Size S0/S1
When ordering a Discrepancy Switch, the following are to be provided:
Switch Type selected according to the control voltage, load current and the type of
a.
load. In this case CHR16 would be suitable
b.
The Switching Configuration required ( refer Fig. 22 ). The switch can be given a
special switch reference :
•
11.
When ordering a Discrepancy Switch, the following are to be provided:
a. Switch Type selected according to the control voltage, load current and the type of
load
In this case CHR16B would be suitable
b. The Switching Configuration required. The switch can be given a special switch
reference :
•
•
S0 V130/F11/6A-EL
CHR16B SGxxx3
c.
The number of Auxiliary contacts required. In this case 1 NO + 1 NC auxiliary
contact are required. Hence the coding for the Push to Turn Interlock Device which
housed the auxiliary contacts is:
• S1 V130/F11/6A-EL
d. EL mounting type of lamp holder would be suitable. Hence the coding for the lamp
holder is:
•
CHR16 SGxxx2
c.
The number of Auxiliary contacts required. In this case 1 NO + 1NC auxiliary contact
are required. Hence the coding for the Push to Turn Interlock Device which housed the
auxiliary contacts is:
HOW TO ORDER - Size S1
S1 Q100/A2/B
e. The Ordering Code as follows:
Description
Reference
CHR16 SGxxx3
Switch
S0 V130/F11/6A-EL
Push to Turn Interlock Device & 1 N0 + 1 NC aux.
contact
6 x 999 T6.8K/60
Filament Lamps
S1 Q100/A2/B
Lamp holder
d. EL mounting type of lamp holder would be suitable. Hence the coding for the lamp holder
is:
•
S0 Q100/RKD001
e. The Ordering Code as follows:
Description
Reference
CHR16 SGxxx2
Switch
S0 V130/F11/6A-EL
Push to Turn Interlock Device & 1 N0+ 1NC aux. contact
4 x 999 T6.8K/60
Filament Lamps
S0 Q100/RKD001
Lamp holder
KRAUS & NAIMER BLUE LINE
78
RC/02/2004
DISCREPANCY SWITCH for PANEL Mounting - Other Versions
Discrepancy Switch with Key Lock Device
• Fitted with separate drive key lock device Type V760 which willallow operation of the
discrepancy switch only by authorised personnels.
• Key lock device available with differnt types of locks
• Available in Size S0 and S1.
Switch
Lamp holder
Key Lock Device
Discrepancy Switch with key lock Size S0
KRAUS & NAIMER BLUE LINE
Discrepancy Switch with key lock Size S1
79
RC/02/2004
Discrepancy Switch - Size S0 Panel Mount
Mounting
Type
Electrical
Drawing
A
Auxillary
contacts
Rating
Ith2
Switch
Reference
SIS
Code
Switch
Depth
Handle
Size
Mounting
Hole
20A
CHR10 SGC081*EL
SIS0001
120
S0
30.5 ø
25A
CHR16 SGC081*EL
SIS0001
120
S0
30.5 ø
B
1
2
3
4
5
6
7
8
Size S0 handle without plate
38
Size S0 handle with plate
KRAUS & NAIMER BLUE LINE
80
RC/02/2004
Discrepancy Switch - Size S1 Panel Mount
Mounting
Type
Electrical
Drawing
50 Ø
OPEN
Size S1 handle without plate
52
52
2
3
4
5
6
7
8
20A
CHR10 RK8201*EL
25A
Switch
Depth
Handle
Size
Mounting
Hole
SIS0001
S1
46 ø
CHR16 RK8201*EL
SIS0001
S1
46 ø
40A
C26
RK8201*EL
SIS0001
S1
46 Ø
20A
CHR10 RK8202*EL
SIS0001
S1
46 ø
25A
CHR16 RK8202*EL
SIS0001
S1
46 ø
CLOSE
2
3
4
5
6
7
8
9
10
11
12
40A
C26
RK8202*EL
SIS0001
S1
46 Ø
1
2
20A
CHR10 RK8203*EL
SIS0001
S1
46 Ø
3
4
5
6
25A
CHR16 RK8203*EL
SIS0001
S1
46 Ø
7
8
9
10
11
12
40A
C26
RK8203*EL
SIS0001
S1
46 Ø
20A
CHR10 RK8204*EL
SIS0001
S1
46 Ø
25A
CHR16 RK8204*EL
SIS0001
S0
46 Ø
40A
C26
RK8204*EL
SIS0001
S1
46 Ø
20A
CHR10 RK8205*EL
SIS0001
S1
46 Ø
25A
CHR16 RK8205*EL
SIS0001
S1
46 Ø
40A
C26
SIS0001
S1
46 Ø
OPEN
CLOSE
CLOSE
1
2
3
4
5
6
7
8
9
10
11
12
OPEN
KRAUS & NAIMER BLUE LINE
SIS
Code
1
OPEN
Size S1 handle with plate
Switch
Reference
CLOSE
1
OPEN
Rating
Ith2
CLOSE
1
2
3
4
5
6
7
8
9
10
11
12
81
RK8205*EL
RC/02/2004
Discrepancy Switch - - For mounting on Mosiac panels 25x25mm, 50 x 50mm or 75 x 75mm
Mounting
Type
Electrical
Drawing
16 ø
OPEN
S00 size for mosiac tile
• 25 x 25 mm
2
3
4
5
6
7
8
2
3
4
5
6
7
8
9
10
11
12
35 ø
2
3
4
5
6
7
8
9
10
11
12
KRAUS & NAIMER BLUE LINE
Handle
Size
Mounting
Hole
CG4
RK8501E
CHR10 RK8501*EL
CHR16 RK8501*EL
SIS0001
SIS0001
SIS0001
S00
S0
S0
16 ø
30 ø
30 Ø
10A
20A
25A
CG4 RK8502E
CHR10 RK8502*EL
CHR16 RK8202*EL
SIS0001
SIS0001
SIS0001
S00
S0
S0
16 ø
30 ø
30 Ø
10A
20A
25A
CG4
RK8503E
CHR10 RK8503*EL
CHR16 RK8503*EL
SIS0001
SIS0001
SIS0001
S00
S0
S0
16 ø
30 ø
30 Ø
10A
20A
25A
CG4
RK8504E
CHR10 RK8504*EL
CHR16 RK8504*EL
SIS0001
SIS0001
SIS0001
S00
S0
S0
16 ø
30 ø
30 Ø
10A
20A
25A
CG4
RK8505E
CHR10 RK8505*EL
CHR16 RK8505*EL
SIS0001
SIS0001
SIS0001
S00
S0
S0
16 ø
30 ø
30 Ø
CLOSE
1
2
3
4
5
6
7
8
9
10
11
12
OPEN
10A
20A
25A
Switch
Depth
CLOSE
1
OPEN
S0 Size for mosiac tile
• 50 x 50 mm
• 75 x 75mm
SIS
Code
CLOSE
1
OPEN
Switch
Reference
CLOSE
1
OPEN
Rating
Ith2
CLOSE
1
2
3
4
5
6
7
8
9
10
11
12
82
RC/02/2004
KEY SWITCH
3. FEATURES OF KEY LOCK DEVICE V750/V750D
The device replace the normal switch handle by a key. Features of the V750/V750D key
lock device are:
a. It has several locking programs which allows the key to be removed up to a maximum of
12 positions.
b. It has several different types of locks/keys. In critical installations, key personals must be
present before operating the electrical circuits. This can be done by issuing different keys
to operate different key switches to the key personals. Hence all the key personals must be
present to switch on all the key switches fitted with different locks before the installation can
finally be switched on. Master key lock systems are available.
c. It is available with single hole mounting of
• 22/25/30 mm ø for S0 switch (20-32A AC21)
• 40 mm ø for S1 switch ( 32-63A/AC21)
4. FEATURES
Kraus & Naimer is able to offer a wide range of key operated switches where:
a. Standard switches are used but the key locks can be programmed for safety/security
applications.
b. Non-standard switches are required with standard programs.
c. Non-standard switches are required with special programs.
1. APPLICATION
Key operated switches are extensively used in situations :
• To prevent inadvertent operation of the electrical circuits.
• To provide security against unauthorised operations of the electrical circuits.
• To ensure that the key operational personals are in attendance before the critical
electrical circuits can be operated.
In ordering key switches, the following information are required:
• Switch Rating
• Types of Mounting
• Types of Key Locks
• Types of Locking Programs
2. TYPES OF KEY LOCKS
a. Switch Rating Fig. 4a
To prevent inadvertent operations, the handle of the critical switch can :
a. Be replaced by a key which can be removed at selected positions using the Kraus &
Naimer key lock device type V750/V750D. To prevent unauthorised duplication of keys or
have master key lock system, high security KABA key locks can be used.
b. Be locked the handle in selected positions by means of a separate key lock device
using the Kraus & Naimer safety key lock device type V760.
c. Be replaced with a removable "handle" type key using the Kraus & Naimer key handle
device type V900 in which the standard Kraus & Naimer handle can be fitted to the key
device. Master key lock systems are available.
KRAUS & NAIMER BLUE LINE
83
Rating Ith2
SwitchType
20A
25A
20A
25A
40A
63A
80A
CHR10
CHR16
CHR10B
CHR16B
C26
C32
C42
Switch Size
S0
S0
S1
S1
S1
S1
S1
RC/02/2004
KEY SWITCH V750
b. Types of Mounting
Various types of mountings are available depending on the requirement:
i. Single hole mountings ( Fig 2 )
Switch of Size S0 can have a basic mounting hole of
•
22.5mm ( for mounting type FT1/FT2/FH3) . Adaptors can be supplied for 25mm
and 30.5mm mounting holes.
•
40mm diameter ( for mounting EL2 )
Switch
Type
CHR10/CHR16
Escutcheon
Plate Size
48 x 48
Mounting
Type
FT2
Mounting Hole
Dimension
22.5 ø
25.0 ø
30.5 ø
Required
Adaptor
S0E T160 11
S0E T160 01
CHR10/CHR16
64 x 64
FH3
22.5 ø
25.0 ø
30.5 ø
S0E T160 11
S0E T160 01
C26/C32/C42
64 x 64
EL2 1)
40 ø
-
1) Use high security KABA key lock
ii. Four screws mounting
The key switch is mounted to the panel by four screws
FT2 Mounting
FH3 Mounting
25 Ø Adaptor
FT1 Mounting
30.5 Ø Adaptor
c.
Escutcheon
Plate Size
-
Mounting
Type
FT1
Mounting Hole
Dimension
22.5 ø
25.0 ø
30.5 ø
CHR10/CHR16
-
EL 1)
25.0 ø
Escutcheon
Plate Size
Mounting
Type
CHR10/CHR16
48 x 48
E
CHR10/CHR16
64 x 64
EG
Types of Locking Program
The Locking Program refers to the position at which the key can be removed from the
lock. a mark on the circle shown in the figure below indicates the position/s at which the key
can be removed from the locking device. For example in Program C, the key can be
removed at 6 and 12 o'clock positions whereas in Program G, the key can be removed at 3,
6, 9 and 12 o'clock positions.
Fig. 4b - Single hole mounting for key switch
Switch
Type
CHR10/CHR16
Switch
Type
Required
Adaptor
S0E T160 11
S0E T160 01
A
E
C
G
H
B
F
D
R
J
K
L
Fig. 4c - Type of Locking Program
KRAUS & NAIMER BLUE LINE
84
RC/02/2004
KEY SWITCH V750
d.
Types of Key Locks
The types of locks refer to the type of keys and lock drives available.
i.
Key Locks for Normal Application
STREBOR Key lock devices are suitable for use with Kraus & Naimer switches for
normal applications. It has 10 different key lock drives available. This feature is
especially useful in installation where certain personnal are authorised to operate important
circuits only. Having different types of locs ensures that only authorised personals are
allowed to operate the crtical circuits.
Fig. 4f - FT1 Mounting
Switch Type
CHR10/CHR16
Mounting Type
FT1/FT2/FH3
Types of Key Lock Available
SF101*/SF105/SF121/SF137
SF191/SF200/SF201/SF203
SF204/SF205
Fig. 4g- FT2 Mounting
Fig. 4h- FH3 Mounting
ii. Key Locks for High Security and Master Key Lock System
KABA Key lock devices are suitable for use with Kraus & Naimer switches for high
security and master key lock system.
Fig. 4d - STREBOR Key lock device
* Unless specified, key lock SF101 will be provided as standard.
S0
V750D
/
3
H
/
1
1
Key Locking Program
• Key removable at
A
C
B
D
E
G
H
K
F
J
L
Type of Mounting
• 1 ..... *FT1 (round front ring)
• 2 ..... *FT2 (square 48x48mm plate)
• 7 ..... *FH3 (square 64x64mm plate)
Switch
Type
CHR10/CHR16
Mounting
Type
E/EG
Types of
Key Lock
KABA 8
( Short cylinder )
Number of
Key Locks
1036
Locking
Program
A, B, C, D, E, F, G
CHR10/CHR16
E/EG
KABA 8
( Long cylinder )
1036
G, H, J, K, L
CHR10/CHR16
E/EG
KABA 20
( Short cylinder )
20,000
A, B, C, D, E, F, G
CHR10/CHR16
E/EG
KABA 20
( Long cylinder )
20,000
G, H, J, K, L
CHR10/CHR16
EL
KABA 8
( Short cylinder )
1036
A, B, C, D, E, F, G
CHR10/CHR16
EL
KABA 8
( Long cylinder )
1036
G, H, J, K, L
CHR10B/CHR16B
EL2
KABA 8
( Centric drive )
1036
A
CHR10B/CHR16B
EL2
KABA 20
( Centric drive )
20,000
A
Fig. 4e - Coding of STREBOR Key Lock Device
KRAUS & NAIMER BLUE LINE
85
RC/02/2004
22
22
32
KEY SWITCH V750
34
25
24
KABA8/ KABA 20
Centric Drive
KABA8/ KABA 20
Short Cyclinder
KABA8/ KABA 20
Long Cyclinder
Fig. 4j KABA Key Lock Device
Fig. 4i- Coding of KABA High Security Key Lock Device for E and EG Mounting
S0 V750D / A 1 A / 1 1
S0 V750D / 1 A 1
Escutcheon plate
Type of Lock
A ... Square
B ... Rectangular
1
2
3
4
Type of Lock
1
2
3
4
...
...
...
...
KABA 8 ( program A - G)
KABA 8 ( program G - L )
KABA 20 ( program A - G )
KABA 20 ( program G - L )
...
...
...
...
KABA 8 ( program A - G)
KABA 8 ( program G - L )
KABA 20 ( program A - G )
KABA 20 ( program G - L )
Locking Program
A
E
C
B
F
D
G
H
K
L
Locking Program
A
E
C
B
F
D
G
H
K
J
L
Mounting
1
J
Mounting
Fig. 4j- Coding of KABA High Security Key Lock Device for E L Mounting
Blank ... E
1
... EG
KRAUS & NAIMER BLUE LINE
... *EL ( 25mm Ø )
86
RC/02/2004
KEY SWITCH V750
Function
S1 V750 / A 1
/
A 1 1
Number
of
poles
39 Ø Round
Mounting plate
Type FT1
48x48 Square
Mounting plate
Type FT2
Switch
Length
(mm)
1
2
3
4
CHR10 A200 *FT1
CHR10 A201 *FT1
CHR10 A202 *FT1
CHR10 A203 *FT1
CHR10 A200-620*FT2
CHR10 A201-620*FT2
CHR10 A202-620*FT2
CHR10 A203-620*FT2
52
52
62
62
1
2
3
4
CHR10 A290 *FT1
CHR10 A291 *FT1
CHR10 A292 *FT1
CHR10 A293 *FT1
CHR10 A290-620*FT2
CHR10 A291-620*FT2
CHR10 A292-620*FT2
CHR10 A293-620*FT2
52
52
62
62
1
2
3
4
CHR10 A210 *FT1
CHR10 A211 *FT1
CHR10 A212 *FT1
CHR10 A213 *FT1
CHR10 A210-620*FT2
CHR10 A211-620*FT2
CHR10 A212-620*FT2
CHR10 A213-620*FT2
52
62
71
81
1
2
3
4
CHR10 A210 *FT1
CHR10 A211 *FT1
CHR10 A212 *FT1
CHR10 A213 *FT1
CHR10 A210-623*FT2
CHR10 A211-623*FT2
CHR10 A212-623*FT2
CHR10 A213-623*FT2
52
62
71
81
Locking Program
- key remove at
OFF
A
ON
Type of Lock
1 ... KABA 8
6 ... KABA 20
Type of Mounting
A ... EL1 ( without escutcheon plate )
B... EL2 ( escutcheon plate 64 x 64mm )
OFF
ON
Type of Version
Blank ... for same switch size
1
... for next smaller switxh size
OFF
Fig. 4k - Coding of KABA High Security Key Lock Device for E L Mounting
1
2
5. ORDERING PROCEDURE
OFF
MAN
a. Normal Key Lock Device
i. Standard Switch
•
•
•
•
20A/AC21 rating
Single hole mounting 22/25/30 mm ø
Escutcheon plate size 48 x 48 mm
Strebor key lock SF101 with key removable at 12 o'clock position only.
AUTO
ORDERING PROCEDURE
ii.
Non-standard Switch
Typical Specification
A synchronising mode selector switch is to be key operated to prevent unauthorised
operation. It shall consist of three positions "MANUAL - NORMAL MANUAL - MANUAL
OVERRIDE" which shall be 90 degrees apart. The key shall be removable at every switching
position. Contact rating shall be 20A/AC21 at 690VAC. The required configuration is as
shown in Fig. 5a
KRAUS & NAIMER BLUE LINE
87
RC/02/2004
KEY SWITCH V750
MANUAL
NORMAL
MANUAL
OVERRIDE
S0 V750D / 3 G / 2 1
Key Locking Program
1
2
- key removable at
3
4
A
C
5
6
B
D
7
8
G
H
K
F
J
L
Type of Mounting
1
2
Fig. 5a - Required contact configuration
v.
How To Order
.....*FT1
.....*FT2
Contact configuration required - refers to Fig. 5a
MANUAL
When ordering a non-standard key switch, the following data are to be provided:
Switch Type
Switch Type to be selected according to the rating and application ( AC21, AC23,
DC etc.) In this case, 20A/AC21 is required and hence switch CHR10 is suitable refer to
Fig. 4a
ii. Type of Mounting
Since engravings are required, mounting FT2 of escutcheon plate 48 x 48 mm can be
used - refer to Fig. 4b
i.
iii. Type of Locking Program.
In this case, the key have to be remove at every switching position for which program G
would be suitable- refer Fig. 4c
NORMAL
MANUAL
OVERRIDE
1
2
3
4
5
6
7
8
.
With the above information, a switch drawing can be prepared as according to requirement. A special switch drawing number CHR10 SG9997 can be allocated by the Kraus &
Naimer's representative - refer Fig. 5b
H
J
E
L
iv. Type of Key Lock required depends on:
• Normal Type/High security lock.
In this case a normal type of lock e.g. STREBOR can be used - refer Fig. 4d. Unless
specified, Stebor lock SF101 will be provided. The required coding for the Key Lock
device will be as follows:
KRAUS & NAIMER BLUE LINE
88
RC/02/2004
KEY SWITCH V750
•
The ordering code of the Group Master Key Lock Systemshall be as follows:
NORMAL
MANUAL
315
270 o
Item
i
ii
iii
45
270
90
225
135
180
MANUAL
A.
MANUAL OVERRIDE
0
B.
NORMAL
300 o
330 o
0o
MANUAL OVERRIDE
30 o
60 o
90 o
1
2
3
4
5
6
7
8
Fig. 5b - Non-standard switch with key lock device
6.
Typical Specification
The master key lock system shall have a rating of 20A/AC21 and 3 pole ON-OFF
switch and should be group as follows:
• Group A shall consist of 15 different locks.
• Group B shall consist of 10 different locks
•
Group C shall consist of 10 different locks
•
•
•
Group D shall consist of 5 different locks.
Key to be remove at "NORMAL" position only
None of the key locks in the groups can be inter-changed and key should be able to
89
Master Key Lock
Description
Switch
Escutcheon plate
Lock device
Code
CHR10 A202-620E
S0 V750D/A1A/11
SOD V757 GT3
LA3043/PP
Qty
1
1
1
Ordering code of Slave Key Lock - Group A
Item
i
ii
iii
Description
Switch
Escutcheon plate
Lock device
xx
................
Lock device
Code
CHR10 A202-620E
S0 V750D/A1A/11
SOD V757 GT
LA3043/01
......................
SOD V757 GT
LA3043/15
C.
Ordering code of Slave Key Lock - Group B
Item
i
ii
iii
Description
Switch
Escutcheon plate
Lock device
xx
.................
Lock device
Code
CHR10 A202-620E
S0 V750D/A1A/11
SOD V757 GT
LA3043/16
......................
SOD V757 GT
LA3043/25
D.
Ordering code of Slave Key Lock - Group C
Item
i
ii
iii.
Description
Switch
Escutcheon plate
Lock device
xx
.................
Lock device
GROUP MASTER KEY LOCK SYSTEM
KRAUS & NAIMER BLUE LINE
remove at the OFF position ( 12 o'clock position ).
A master key lock should be provided to operate all the locks in the group.
c)
Slave Key Lock - Group D
Item
i
ii
iii.
Description
Switch
Escutcheon plate
Lock device
xx
.................
Lock device
Qty
15
15
1
1
Qty
10
10
1
1
Code
CHR10 A202-620E
S0 V750D/A1A/11
SOD V757 GT
LA3043/26
......................
SOD V757 GT
LA3043/35
Qty
10
10
1
Code
CHR10 A202-620E
S0 V750D/A1A/11
SOD V757 GT
LA3043/36
......................
SOD V757 GT
LA3043.
Qty
5
5
1
1
1
RC/02/2004
KEY SWITCH V750
7. SPECIAL KEY LOCK SYSTEM
Three key switches 20A/ 4P ON-OFF are to be used to control the operating coils of 3
circuit breakers as follows:
• The key K1 for key switch S1 can also be used to operate key switch SZ.
• The key K2 for key switch S2 can also be used to operate key switch SZ.
• However, the key K1 CANNOT be used to operate key switch S2. Similarly, K2 CANNOT
be used to operate key switch S1.
• Key to be remove at "OFF" position only
Key Lock Device
S0 V750D/A1A1
OFF
SZ
ON
K1
K2
Grand Master Key
SOD V750 GT3
LA3043/PP
CBZ
GROUP A
15 different
keys
OFF
GROUP C
10 different
keys
GROUP D
5 different
keys
OFF
S2
S1
GROUP B
10 different
keys
ON
ON
CB1
CB2
K1
K2
Key lock device
1. S0D V757 GT
LA3043/01
2. S0D V757 GT
LA3043/02
.
15. S0D V757 GT
LA3043/15
Fig. 6 - Special key lock system
Key lock device
1. S0D V757 GT
LA3043/16
2. S0D V757 GT
LA3043/17
.
10. S0D V757 GT
LA3043/25
Key lock device
1. S0D V757 GT
LA3043/26
2. S0D V757 GT
LA3043/01
.
10. S0D V757 GT
LA3043/35
Key lock device
1. S0D V757 GT
LA3043/36
2. S0D V757 GT
LA3043/37
.
5. S0D V757 GT
LA3043/40
Fig. 7 - Master key lock system
KRAUS & NAIMER BLUE LINE
90
RC/02/2004
KEY SWITCH V750
9. GROUP MASTER KEY LOCK SYSTEM WITH DUST COVER
( Key remove at several positions)
A. Ordering code of Key Swtch S1
Item
i.
ii.
Description
Switch
Key Lock device
Reference
CHR10 A293-622 *E
S0 V750D/A20
S0D V751 ZZ
S0D V750 34
% SPERRE LA3251/1
The examples provided in items (1) to (4) allows key to be remove only at one position i.e.
at 12 o'clock position. Where key need to be removed at more than one positions, the ordering
code shall be:
A. Ordering Code of GROUP Master Key Swtch KGM - key remove at several positions
(1o'clock, 2 o'clock .... to 12 o'clock )
B. Ordering code of Key Swtch S2
Item
i.
ii.
Description
Switch
Key Lock device
Reference
CHR10 A293-622 *E
S0 V750D/A20
S0D V751 ZZ
S0D V750 34
% SPERRE LA3251/2
Description
Switch
Key Lock Device
Description
Switch
Key Lock device
iii.
Dust Cover
Reference
CHR10 A211-620 *E
S0 V750D/AZ0/1
S0D V756 GZST
%NUMBER LA 3291/KGM
S0D V750 34
S0D V750 ST
B Ordering Code of MASTER Key Swtch KMA/KMB - key remove at several positions
( 1o'clock, 2 o'clock .... to 12 o'clock )
C. Ordering code of Key Swtch SZ
Item
i.
II.
Item
i.
ii.
Reference
CHR10 A293-622 *E
S0 V750D/A20
S0D V751 ZZ
S0D V750 34
% SPHERE LA3251/Z
Item
i.
ii.
Description
Switch
Key Lock device
8. KEY LOCK WITH DUST PROTECTION COVER
iii.
Dust Cover
Dust protection covers are available on KABA key lock device to prevent entry of dust
and moisture into the metal key lock cylinder which may caused jamming. The key to be
remove only at "OFF" position only.
C Ordering Code of Key Swtch KA1, KA2, KA3, KB1, KB2, KB3 - key remove at several
positions ( 1o'clock, 2 o'clock .... to 12 o'clock )
A. Ordering code of Key Switch with Dust Cover
i.e of Key Swtch with dust cover
Item
i.
ii.
Description
Switch
Key Lock device
iii.
Dust Cover
KRAUS & NAIMER BLUE LINE
Reference
CHR10 A293-622 *E
S0 V750D/AZ0/1
S0D V751 ZZST
%LA .....................
SOD V750 ST
91
Item
i.
ii.
Description
Switch
Key Lock device
iii.
Dust Cover
Reference
CHR10 A211-620 *E
S0 V750D/AZ0/1
S0D V756 GZST
%NUMBER LA 3291/KMA
%NUMBER LA 3291/KMB
S0D V750 34
S0D V750 ST
Reference
CHR10 A211-620 *E
S0 V750D/AZ0/1
S0D V756 GZST
%NUMBER LA 3291/KA1
%NUMBER LA 3291/KA2
%NUMBER LA 3291/KA3
%NUMBER LA 3291/KB1
%NUMBER LA 3291/KB2
%NUMBER LA 3291/KB3
S0D V750 34
S0D V750 ST
RC/02/2004
Group Master Key
Switch KGM
Master Key Switch
KMA
Master Key
Switch KMB
Key Switch
KA1
Key Switch
KA2
Key Switch
KA3
Key Switch
KB1
KRAUS & NAIMER BLUE LINE
Key Switch
KB2
Key Switch
KB3
92
RC/02/2004
KEY SWITCH V760
10.
V760/V765 SAFETY KEY LOCK DEVICE with separate drive
The Safety Key Lock device type V760 allows the switching operation
to be done by the switch handle. With the V760, it is possible to lock the
handle at selected positions by means of a separate key lock device.
The V760 is available from size S0 to S3 and can be use with tandem
drive M300 and door interlock M280D.
S1 V760 /
Plate Frame
A ... Square
B ... Rectangular
The following information are required when ordering either a standard switch/special switch which is to be fitted with a separate key lock
device.
Key Program
1 ... Key removable at
Lock/Unlock positions
2 ... Key removable at
Lock position only
a. Switch Ratings
b. Type of Escutcheon Plate
• Square
• Rectangular
Type of Lock
V765 key lock device
c. Key Program required.
The key program refers to the position/s at which the key is to be removed from the lock
which can occur when:
• Key is to be removed at both LOCKED and UNLOCKED positions. LOCKED position
refers to the position where it is not possible to turn the handle of the switch because it is
locked at that particular position by the separate key lock device.
• Key is to be removed only at the LOCKED position.
B
C
D
E
G
H
...
...
...
...
...
...
Zeiss
BKS
KABA 8
Strebor
KABA 20
Ronis
Locking Program
1 ... 1 position (0) to be locked
all other positions not to be locked
2 ... All positions to be locked
3 ... 1 position not to be locked
all other positions to be locked
9 ... Special locking program - specify
d.
Type of Lock
Various types of locks are available namely ZEISS, BKS, STREBOR and RONIS for
general application and KABA 8 locks for high security/master key lock system.
When using STREBOR locks for S0 and S1 switches, type SF101 key lock will be
provided unless specified.
Angular displacement
20
30
45
60
90
e.
Locking Programs
Various standard locking programs are available. For non-standard programs, the
following information are required:
• The number of positions to be locked
• The position/s to be locked.
KRAUS & NAIMER BLUE LINE
B 1 E 2 / 90 1
...
...
...
...
...
20 deg. switching angle
30 deg. switching angle
45 deg. switching angle
60 deg. switching angle
90 deg. switching angle
Fig. 10a - Ordering Code
93
RC/02/2004
KEY SWITCH V760
11.
ORDERING PROCEDURE
Coding of required Safety Key Lock
The required coding is:
a. Typical Specifications
A manual override selector switch is to be fitted with a separate key lock device for
security reasons. The selector switch shall have three switching positions "MANUAL-NORMAL-MANUAL OVERRIDE ". The switching angle shall be 90 degrees. The contact rating
shall be 25A/AC21 660VAC.
The separate key lock device should be able to lock the selector switch at all positions.
The key should be able to be remove at both LOCKED and UNLOCKED situation.
The selector switch handle and escutcheon plate shall be big enough for easy operation
by the operator.
The contact configuration required is as follows:
MANUAL
NORMAL
S1 V760 /
B 1 E 2 / 90 1
Plate Frame
A ... Square
B ... Rectangular
Key Program
1 ... Key removable at
Lock/Unlock positions
2 ... Key removable at
Lock position only
MANUAL
OVERRIDE
1
2
3
4
5
6
7
8
Type of Lock
B
C
D
E
G
H
...
...
...
...
...
...
Zeiss
BKS
KABA 8
Strebor
KABA 20
Ronis
Locking Program
1 ... 1 position (0) to be locked
all other positions not to be locked
2 ... All positions to be locked
3 ... 1 position not to be locked
all other positions to be locked
9 ... Special locking program - specify
Fig. 11a - Required contact configuration
b. How To Order
When ordering a switch to be fitted with a separate key lock device V760, the following
informations are require:
i.
Switch Type
Switch type is selected according to the ratings and application ( AC21, AC23 etc.) In this
case 25A AC21 is required and hence switch CHR16B can be used.
ii
Contact configuration - refer Fig. 11.
iii.
Key Program.
In this case, the key is to be remove at both LOCKED and UNLOCKED positions.
iv.
Type of Lock.
Unless specified, STREBOR SF101 lock device will be provided.
KRAUS & NAIMER BLUE LINE
Angular displacement
20
30
45
60
90
94
...
...
...
...
...
20 deg. switching angle
30 deg. switching angle
45 deg. switching angle
60 deg. switching angle
90 deg. switching angle
RC/02/2004
KEY SWITCH V760
NORMAL
MANUAL
270 o
45
270
90
225
135
180
MANUAL
MANUAL OVERRIDE
0
315
NORMAL
300 o
330 o
0o
MANUAL OVERRIDE
30 o
60 o
90 o
1
2
3
4
5
6
7
8
Fig. 11b - Special switch diagram
With the information provided , a switch drawing can be prepared as according to requirement. A special switch drawing number CHR16B SG9996 can be allocated by the Kraus &
Naimer's representative - refer Fig. 11b
KRAUS & NAIMER BLUE LINE
95
RC/02/2004
KEY SWITCH V900
12.
V900 - KEYED HANDLE DEVICE
Program
Number
For Key
Profile
Angular
Movement
Key Removable
Locations
014
A, C, D, E, F, H, K, M, N, P
45
015
L, R, B
30/45/60/90
016
A, C, D, E, F, H, K, M, N, P
30/45/60/90
The V900 basically resembles the features of a
cylinder lock. Therefore, it provides a number of features
which are usually found on cylinder locks such as:
• Variety of locking arrangement
• Removal of the key in predetermined positions.
• Master key lock system.
It can be operated by a flat key ( V902 ) or a key
equipped with a Kraus & Naimer Size S1 handle which
gives it the feature of a "removable handle " control
switch.
The following information are required
when orderinga standard switch/special switch which is to
be fitted with a V900.
c
a.
The locking profile refers to the type of key lock selected which would make it suitable for
master group key lock system, group key lock system or individual key lock.
Switch Ratings
Switch Type
CHR10B
CHR16B
C26
C32
C42
b.
B
Rating AC21
20A
25A
32A
40A
63A
Voltage
690V AC
690V AC
690V AC
690V AC
690V AC
P
L
R
The Locking Profile
N
M
K
H
F
E
D
C
A
F
E
D
C
A
G
Locking Program
The locking program refers
•
The key removable positions.
•
The type of key profile suitable
Program
For Key
Number
Profile
Angular
Movement
Key Removable
Locations
P
011
A, C, D, E, F, H, K, M, N, P
30/45/60/90
012
A, C, D, E, F, H, K, M, N, P
30/60/90
013
A, C, D, E, F, H, K, M, N, P
30/60/90
KRAUS & NAIMER BLUE LINE
d.
N
M
K
H
The type of keyed handle device required.
•
Flat key
•
Key equipped with a standard Kraus & Naimer Size S1 handle. Unless specified,
type S1 G001 handle will be provided as standard.
96
RC/02/2004
KEY SWITCH V900
13.
SPECIAL LOCK - KEY Combination
14.
Keyed handle device V900 with locking program 015 provides a special arrangement as
follows:
• When use with key V901/B ( or V902/B) , the key can be turn in both clockwise and
anti-clockwise direction.
• When use with key V901/L ( or V902/L), the key can be turn in the anti-clowise direction
• When use with key V901/R ( or V902/R), the key can be turn in the anti-clowise direction
If pratical requirements exceed the number of standard locking profiles , cipher identification instead of lettering allows expansion of available number of ( non-interchangeable )
locking profiles:
•
Series 1 - Key numerals 01-16 with master key G0 ( identical with G )
•
Series 2 - Key numerals 21 - 36, master key G2
•
Series 4 - Key numerals 41 - 56 , master key G4
a. Ordering Code Key Lock V900
ORDERING CODE KEY V901/902
a.
S1 V900 /
C
.....
.....
.....
.....
.....
.....
Special Profile
A
Locking Program
A
C
D
K
L
S
SPECIAL PROFILES FOR KEYED HANDLE DEVICE
S1B
Program 015
Program 011
Program 016
Program 014
Program 013
Program 012
V901
/
Z
G4
Type of Keyed
Handle Device
V901 ... Flat key
V902 ... Key with switch handle
Locking Profile
A, B, C, D, E, F, H,
K, L, M, N, P, R
Special Locking Number
01 .....
Locking profile 01
16 .....
G0 .....
Locking profile 16
Master key for locking profile 01 - 16
21 .....
Locking profile 01
36 .....
G2 .....
Locking profile 16
Master key for locking profile 21 - 36
Type of Keyed
Handle Device
41 .....
Locking profile 41
V901 ... Flat key
V902 ... Key with switch handle
56 .....
G4 .....
Locking profile 56
Master key for locking profile 41 - 56
b. Ordering Code key V901/902 - Standard Profile
S1 V901
/
A
Locking Profile
A, B, C, D, E, F, H,
K, L, M, N,P, R
KRAUS & NAIMER BLUE LINE
97
RC/02/2004
Download