Prices as of April 27, 2016. Check Web site for most current prices.
Single-Level Terminal Blocks
Feed-through terminal blocks provide
the means to connect two wires together,
and are available in sizes suitable for up
to 8AWG wire.
• Screw connection terminal
• 35mm DIN-rail mountable
• LVD 2006/95/EC
12
G
AW
10
G
AW
Terminal Blocks
8
G
AW
Power
Distribution
Blocks
Wiring
Accessories
DN-T12-A
Series: EURO 2.5
DN-T8
Series: EURO 6
DN-T10-A
Series: EURO 4
Ordering Information
Part Number
Dimensions
mm [inches]
DN-T12-A
DN-T10-A
Gray
Blue
Brown
Black
Available Green
Colors
Orange
Red
Yellow
White
Stripping Length
Tightening Torque
Density
UL Approval*
CSA Approval
VDE Approval
Operating
Temperature
SCCR Rating
CE Conformity
Agency File #
DN-T12-A
DN-T12B-A
DN-T12BR-A
DN-T12BLK-A
DN-T12GRN-A
DN-T12ORG-A
DN-T12RED-A
DN-T12YEL-A
DN-T12W-A
Pcs/ Price Part Number Pcs/ Price Part Number
Pkg
Pkg
100 $37.50 DN-T10-A
100 $43.50 DN-T8
100 $42.00 DN-T10B-A
100 $47.50 DN-T8B
100 $42.00 DN-T10BR-A
100 $47.50
–
100 $42.00 DN-T10BLK-A 100 $47.50 DN-T8BLK
100 $42.00 DN-T10GRN-A 100 $47.50 DN-T8GRN
100 $42.00 DN-T10ORG-A 100 $47.50 DN-T8ORG
100 $42.00 DN-T10RED-A 100 $47.50 DN-T8RED
100 $42.00 DN-T10YEL-A
100 $47.50 DN-T8YEL
100 $42.00 DN-T10W-A
100 $47.50 DN-T8W
Pcs/ Price
Pkg
50
50
–
50
50
50
50
50
50
$34.50
$38.00
–
$38.00
$38.00
$38.00
$38.00
$38.00
$38.00
Technical Specifications
10mm [0.39 in]
10mm [0.39 in]
12mm [0.47 in]
0.5 N·m [4 lb·in]
0.8 N·m [7 lb·in]
1.2 N·m [10.6 lb·in]
200/m [60 pcs/ft]
166/m [50 pcs/ft]
142/m [43 pcs/ft]
600V
20A 24-12 AWG
600V
30A 24-10 AWG
600V
50A 22-8 AWG
600V
24A 24-12 AWG
600V
30A 24-10 AWG
600V
50A 22-8 AWG
800V
24A
2.5 mm²
800V
32A
4mm²
800V
41A
6mm²
Ambient air temp: -20°C to 105°C [-4°F to 221°F]
Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
10kA per Table SB4.1, 2009, UL 508A, maximum short circuit current rating for unmarked components
CE (EN 60947-1 / EN 60947-7-1)
UL E179129
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
End Covers
Separators
2-pole
Jumpers
DN-T8
3-pole
Company
Information
DN-EC1210
DN-EC1210MN
DN-S1210
DN-S1210MN
DN-2J2Y
DN-2J2YMN
DN-3J2Y
DN-3J2YMN
DN-24J2Y
Accessories
100
25
100
25
100
25
100
25
5
$26.00
$8.00
$30.50
$9.25
$26.00
$7.50
$36.50
$10.25
$16.00
DN-EC1210
DN-EC1210MN
DN-S1210
DN-S1210MN
DN-2J4Y
DN-2J4YMN
DN-3J4Y
DN-3J4YMN
DN-24J4Y
100
25
100
25
100
25
100
25
5
$26.00
$8.00
$30.50
$9.25
$27.50
$8.00
$43.50
$12.00
$17.00
DN-EC86
DN-EC86MN
DN-S86
DN-S86MN
100
25
100
25
$28.00
$8.00
$36.50
$7.75
–
Sensor Cables
and Connectors
M12 Junction
Blocks
Panel Interface
Connectors
Wiring Duct
Cable Ties
Wire
Bulk
Multi-conductor
Cables
Wire
Management
Products
Power Supplies
DC Converters
Circuit Protection
Tools
Test
Equipment
Enclosures
*Copper Wire Only
**Jumper Cutting Tools DN-JxCUT cut the applicable multi-pole jumpers and MAINTAIN THE JUMPER INSULATION
Note: For more information on accessories, see the DINnectors Accessories section of this chapter.
Book 3 (14.3)
Terminal Blocks
Multi-wire
Connectors
Transformers
and Filters
5
$24.00
24-pole
DN-24J8
Jumper Cutting DN-J2CUT
1
$46.50 DN-J4CUT
1
$46.50
–
Tool**
100 $36.50 DN-C10
100 $36.50 DN-C86
100 $36.50
DN-C12
Top Cover
25
$7.75 DN-C10MN
25
$7.75 DN-C86MN
25
$7.75
DN-C12MN
10 $24.50 DN-TPR
10 $24.50
Test Plug/Red DN-TPR
–
10 $24.50 DN-TPB
10 $24.50
Test Plug/Black DN-TPB
10 $28.00 DN-R35S1
10 $28.00 DN-R35S1
10 $28.00
7.5 mm DN-R35S1
2
$9.00 DN-R35S1-2
2
$9.00 DN-R35S1-2
2
$9.00
high DN-R35S1-2
35mm
10 $49.50 DN-R35HS1
10 $49.50 DN-R35HS1
10 $49.50
DIN Rail 15mm DN-R35HS1
high DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00 DN-R35HS1-2 2 $12.00
50 $39.50 DN-EB35
50 $39.50 DN-EB35
50 $39.50
DN-EB35
20 $18.00 DN-EB35MN
20 $18.00 DN-EB35MN
20 $18.00
DN-EB35MN
50 $28.50 DN-EB35-A
50 $28.50 DN-EB35-A
50 $28.50
DN-EB35-A
End Brackets
DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50 DN-EB35-A-10 10 $7.50
50 $25.50 DN-QEB35
50 $25.50 DN-QEB35
50 $25.50
DN-QEB35
DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50 DN-QEB35-10 10 $7.50
Angled
50 $49.50 DN-ASB1
50 $49.50 DN-ASB1
50 $49.50
Support Bracket DN-ASB1
or
500/ various DN-L or
500/ various DN-L or
500/ various
Marking Tags DN-LA
100
100
100
DN-LT series
DN-LT series
DN-LT series
w w w. a u t o m a t i o n d i r e c t . c o m / t e r m i n a l - b l o c k s
ZIPLink
Connection
System
eTB-45
Enclosure
Climate Control
Safety: Electrical
Components
Safety: Protective
Wear
Terms and
Conditions
Prices as of April 27, 2016. Check Web site for most current prices.
Single-Level Terminal Blocks
3/0
G
AW
1/0
G
AW
4
G
AW
6
G
AW
• Screw connection
terminal
• 35mm DIN-rail
mountable
• LVD 2006/95/EC
DN-T4 Series:
EURO 16-25/35
DN-T6 Series:
EURO 10/35
DN-T3/0 Series:
EURO 70/35
DN-T1/0 Series:
EURO 35-50/35
Ordering Information
Part
Number
Gray DN-T6
Blue DN-T6B
Available
Colors
Stripping Length
Tightening Torque
Density
UL Approval*
CSA Approval
VDE Approval
Operating Temperature
SCCR Rating
CE Conformity
Agency File #
Pcs/ Price Part
Pkg
Number
50 $46.00 DN-T4
50 $50.00 DN-T4B
Pcs/ Price Part
Pkg
Number
50 $39.00 DN-T1/0
50 $41.50 DN-T1/0B
Pcs/
Pkg
25
25
Price Part
Number
$56.00 DN-T3/0
$58.00
Pcs/ Price
Pkg
10
–
–
$81.00
–
Technical Specifications
12mm [0.47 in]
14mm [0.55 in]
17mm [0.67 in]
26mm [1.02 in]
2.0 N·m [18.0 lb·in]
3.0 N·m [26.5 lb·in]
5.0 N·m [44 lb·in]
10 N·m [89 lb·in]
111/m [33 pcs/ft]
83/m [25 pcs/ft]
62/m [19 pcs/ft]
38/m [11 pcs/ft]
600V
65A
20-6 AWG
600V
85A
14-4 AWG
600V
130A 14-1/0 AWG 600V
185A 4-3/0 AWG
600V
80A
18-6 AWG
600V
105A 14-4 AWG
600V
130A 14-1/0 AWG 600V
185A 4-3/0 AWG
750V
63A
10mm²
750V
110A
25mm²
800V
150A
50mm²
800V
192A
70mm²
Ambient air temperature: -20°C to 105°C [-4°F to 221°F] / Relative humidity: 50% max at 40°C [104°F]; 90% max at 20°C [68°F]
10kA per Table SB4.1, 2009, UL 508A, Maximum short circuit current rating for unmarked components
CE (EN 60947-1 / EN 60947-7-1)
UL E179129
Note: To obtain the most current agency approval information, see the Agency Approval Checklist section on the specific part number's web page.
End Covers
Separators
2-pole
3-pole
4-pole
Multi-pole
7.5 mm
high
35mm
DIN Rail
15mm
high
Angled Support Bracket
Jumpers
Marking Tags
*Copper wire only
DN-EC86
DN-EC86MN
DN-S86
DN-S86MN
DN-2J6
DN-3J6
DN-4J6
DN-55J6
DN-R35S1
DN-R35S1-2
DN-R35HS1
DN-R35HS1-2
DN-ASB1
DN-L or
DN-LT series
Accessories
100 $28.00
25
$8.00
100 $36.50
25
$7.75
100 $45.00
100 $78.00
100 $100.00
1
$15.00
10 $28.00
2
$9.00
10 $49.50
DN-EC4
DN-EC4MN
50
10
$17.00 DN-EC1/0
$3.50 DN-EC1/0MN
–
DN-R35S1
DN-R35S1-2
DN-R35HS1
2
$12.00 DN-R35HS1-2
50 $49.50 DN-ASB1
DN-L or
500/
100 various DN-LT series
50
10
$19.50
$4.00
Included
$28.00 DN-R35S1
$9.00 DN-R35S1-2
$49.50 DN-R35HS1
–
10
2
10
$28.00
$9.00
$49.50
2
$12.00
–
–
DN-R35S1
DN-R35S1-2
DN-R35HS1
2 $12.00 DN-R35HS1-2
2
$12.00 DN-R35HS1-2
50 $49.50 DN-ASB1
50 $49.50 DN-ASB1
DN-L
or
DN-L or
500/
500/
100 various DN-LT series
100 various DN-LT series
10
2
10
–
10
2
10
$28.00
$9.00
$49.50
50 $49.50
500/
100 various
For more information on accessories, see the DINnectors Accessories section of this chapter.
Dimensions
DN-T3/0
DN-T6
44 mm
[1.73 in]
75 mm
[2.95 in]
74 mm
[2.91 in]
26 mm
[1.02 in]
DN-T1/0
DN-T4
50 mm
[1.97 in]
9 mm
[0.35 in]
49 mm
[1.93 in]
56 mm
[2.20 in]
12 mm
[0.47 in]
61 mm
[2.40 in]
62 mm
[2.44 in]
16 mm
[0.63 in]
Note: Screw is a Hex Bolt, Size M8
Book 3 (14.3)
eTB-46
Terminal Blocks
1 - 8 0 0 - 633 - 0 4 0 5
Prices as of April 27, 2016. Check Web site for most current prices.
Accessories
Company
Information
DN-LB (blank)
shown on right
Terminal Blocks
Power
Distribution
Blocks
Wiring
Accessories
ZIPLink
Connection
System
DN-L
• Fits terminal block types: All except
Screwless DINnectors , DN-T12-A,
DN-M10-A, DN-MG, and DN-TL series
• Material: Thermoplastic with heat
embossed black print
Note:
1. The marking sequence of 50 tags (i.e. 101-150) is
printed 10 times in each package of 500 tags.
2. The DN-L tags fit all DINnectors 6mm wide and
wider.
3. The DN-L tags
Dimensions
fit all DIN12 mm
6 mm
nectors 6mm
[0.47 in]
[0.23 in]
wide and wider
but will leave
a
gap between tags
on blocks wider
than 6mm.
Marking
Sequence
1-50
51-100
101-150
151-200
201-250
251-300
301-350
351-400
401-450
Blank
L1, L2, L3, L, N, GND,
+, -, COM,COM*
Part#
DN-L50
DN-L100
DN-L150
DN-L200
DN-L250
DN-L300
DN-L350
DN-L400
DN-L450
DN-LB
Pcs/ Price
Pkg
DN-LS
500
500
500
500
500
500
500
500
500
500
$32.50
$32.50
$32.50
$32.50
$32.50
$32.50
$32.50
$32.50
$32.50
$22.00
500
$32.50
DN-QL
• Fits terminal block types: Screwless
DN-Q series
• Material: Thermoplastic with heat embossed black print. Packaged 100 labels
per card, and five cards per box.
Note:
1. The marking sequence (i.e. 1-100)
is printed five times in each
Dimensions
package of 500 tags.
DN-QLS Shown
Marking Sequence
1-100
101-200
201-300
301.400
401-500
Blank Tags
L1, L2, L3, L, N, +,-,
COM,COM*
Part # Pcs/
Pkg Price
DN-QL100
DN-QL200
DN-QL300
DN-QL400
DN-QL500
DN-QLB
DN-QLS
500
500
500
500
500
500
DN-LTA marker shown top; DN-LT60 marker
shown middle;
DN-LTGND shown bottom
DN-LAB (blank) shown on left;
part of DN-LA100 on right
DN-LA
• Fits terminal block types: DN-T12-A
series
• Material: Thermoplastic with heat
embossed black print
Note:
1. T he marking sequence (i.e. 1-100) is printed five
times in each package of 500 tags.
2. T he DN-T12-A series is 5mm wide, so the 6mm
wide DN-L tags do not fit these blocks.
3. T he DN-LA tags fit
Dimensions
all DINnectors 5mm
12 mm
5 mm
wide and wider but
[0.47 in]
[0.19 in]
will leave a gap
between tags on
blocks wider than
5mm.
Marking
Sequence
1-100
101-200
201-300
301-400
Blank Tags
L1, L2, L3, L,
N, GND, +, -,
COM,COM*
Part#
DN-LA100
DN-LA200
DN-LA300
DN-LA400
DN-LAB
Pcs/ Price
Pkg
DN-LAS
500
500
500
500
500
$32.50
$32.50
$32.50
$32.50
$32.50
500
$32.50
DN-LAT-A
• Fits terminal block types: Triple level
DN-TL14
Material: Thermoplastic with heat
embossed black print
Dimensions
Note:
5mm
[0.19 in]
1. T he marking sequence (i.e.
1-100) is printed five times in
each package of 500 tags.
Marking
Sequence
1-100
101-200
201-300
301-400
401-500
501-600
Blank Tags
L1, L2, L3, L, N,
+,-, COM,COM*
Part #
DN-LAT100-A
DN-LAT200-A
DN-LAT300-A
DN-LAT400-A
DN-LAT500-A
DN-LAT600-A
DN-LATB-A
$25.50
$25.50
$25.50
$25.50
$25.50
$21.50
500 $29.00
DN-LATS-A
6mm
[0.23 in]
Pcs/ Price
Pkg
500
500
500
500
500
500
500
$29.00
$29.00
$29.00
$29.00
$29.00
$29.00
$21.00
500 $29.00
DN-LT
• Fits terminal block types: All except
Screwless DINnectors
(see DN-QL series)
•M
aterial: Thermoplastic with heat
embossed black print
Note:
1. T hese marking tags allow the
flexibility of creating custom
marking sequences on site.
2. T he DN-M10-A support a
maximum of three digits (tags),
while other DINnectors support
up to four digits (tags)
Marking
Sequence
1-5
6-0
1
2
3
4
5
6
7
8
9
0
Unprinted
A
B
C
D
E
F
G
H
I
J
K
L
M
N
–
P
Q
R
S
T
U
V
W
X
Y
Z
+
~
=
Part#
DN-LT15
DN-LT60
DN-LT1
DN-LT2
DN-LT3
DN-LT4
DN-LT5
DN-LT6
DN-LT7
DN-LT8
DN-LT9
DN-LT0
DN-LTBLNK
DN-LTA
DN-LTB
DN-LTC
DN-LTD
DN-LTE
DN-LTF
DN-LTG
DN-LTH
DN-LTI
DN-LTJ
DN-LTK
DN-LTL
DN-LTM
DN-LTN
–
DN-LTP
DN-LTQ
DN-LTR
DN-LTS
DN-LTT
DN-LTU
DN-LTV
DN-LTW
DN-LTX
DN-LTY
DN-LTZ
DN-LTGND
DN-LTPOS
DN-LTNEG
DN-LTAC
DN-LTDC
Terminal Blocks
Sensor Cables
and Connectors
M12 Junction
Blocks
Panel Interface
Connectors
Wiring Duct
Dimensions
5 mm
[0.19 in]
3 mm
[0.11 in]
Cable Ties
Wire
Pcs/
Pkg
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
–
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
Price
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
–
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
$5.75
Book 3 (14.3)
w w w. a u t o m a t i o n d i r e c t . c o m / t e r m i n a l - b l o c k s
Multi-wire
Connectors
eTB-89
Bulk
Multi-conductor
Cables
Wire
Management
Products
Power Supplies
DC Converters
Transformers
and Filters
Circuit Protection
Tools
Test
Equipment
Enclosures
Enclosure
Climate Control
Safety: Electrical
Components
Safety: Protective
Wear
Terms and
Conditions
Prices as of April 27, 2016. Check Web site for most current prices.
Accessories
Terminal Marking Accessories
DN-EMLBL1
DN-EMLBL2
Part #
Description
DN-EMLBL1
DN-EMLBL2
DN-EMLBL3
Labels printed 1 – 12
Blank labels
Labels printed 13 – 24
DN-EMLBL3
For Use With
Pcs/Pkg
Price
Each
100
$5.25
100
$7.25
100
$7.25
DN-EMPEG1 pin protectors for
DN-xEMXxx plug-in terminal
blocks
DN-MTA dimensions
20.5 mm
[0.81 in]
5.9 mm
[0.23 in]
Part#
Description
Pcs/Pkg
Price
Each
DN-MTA
Marking tag adapter
holds up to six
DN-LT tags
50
$8.00
Note: DN-MTA adapter does not fit DN-T12-A
terminal blocks.
3 mm
[0.12 in]
DN-MTA marking tag adapter
Marking Pen – for terminal and wire marking tags
• Permanent
• Smudge-proof
• Waterproof
• Weatherproof
• Lightfast (won’t fade)
• Dries in seconds
(excellent for left-handed users)
• Dry-safe (pen can be left uncapped for
days without drying out)
• Low odor ink
Part#
Description
DN-MP
Indelible black ink
marking pen
Pcs/
Pkg
Price
Each
1
$3.75
Marking pen
Wire Marking Accessories
Part #
Description
For Use
With
Pcs/
Pkg
Price
Each
DN-WMTAG1
Wire tag – blank
all DN-WM-x
wire tag holders
525
$34.50
DN-WM-1
Wire tag holder, clear, 12mm length, 0.051–0.118 in diameter;
for 22–16 AWG wire
Wire tag holder, clear, 12mm length, 0.098–0.196 in diameter;
for 16-11 AWG wire
Wire tag holder, clear, 12mm length, 0.157–0.393 in diameter;
for 13–5 AWG wire
Wire tag holder, clear, 12mm length, 0.314–0.629 in diameter;
for 5AWG wire
200
$7.00
200
$7.00
100
$4.75
100
$4.25
DN-WM-2
DN-WM-3
DN-WMTAG1 wire tags &
DN-WM-x wire tag holders
DN-WM-4
DN-WMTAG1
Book 3 (14.3)
eTB-90
Terminal Blocks
1 - 8 0 0 - 633 - 0 4 0 5