OPTEVA fi 760 ADVANCED FUNCTION WALK-UP ATM
THROUGH THE WALL
R
CALL 1-800-999-3600
CONSULT WITH DIEBOLD INSTALLATION/SERVICE
BRANCH FOR ADDITIONAL DETAILS AND INFORMATION.
PLEASE SEE PLANNING AND SITE PREPARATION GUIDE
TP-820718-001.
TOP FUNCTION KEY
CARD READER
STATEMENT PRINTER
(
DI
M ENSI
ONS I
NI
NCHES)
ADVANCED FUNCTION
DISPENSER
794
TOP
FUNCTION
KEY
(3114")
13
768
13
1
(
2")
(3014")
1
(
2")
193
1197
CAE
(
2738"
)
695 SAFE
1038
ADA
82
ADVANCED
FUNCTION
DISPENSER
STATEMENT
PRINTER
1
(47 8")
9
16")
(7
1000
(3938")
(40 4")
152
(6")
(40 4")
1022
193
1219
9
16")
(48")
(7
1000
152
(6")
(3938")
1
152
(6")
1022
1
43
851
(3312")
11
16")
(1
207
873
43
(818")
(3438")
(11116")
1247
193
1050
152
1050
207
901
43
(4918")
(7916")
(4138")
(6")
(4138")
(818")
(35 2")
1
(11116")
HEIGHT - FROM SIDEWALK LEVEL
102
(314")
CARD
READER
HEIGHT DEPTH HEIGHT DEPTH HEIGHT DEPTH HEIGHT DEPTH
CSA
(
4078"
)
DI
M ENSI
ONS I
N MI
LLI
M ETRES
L549
5 HIGH WITH 13mm 1
(2") SAFE
DEPTH - FROM FRONT EDGE OF BEZEL
(4")
610 W.O.
WALL OPENING HEIGHT NOTE #1:
(24")
766mm (3018") MAXIMUM HEIGHT FROM EXTERIOR SIDEWALK / FLOOR LEVEL TO
343
(
1312"
)
THI
RD ANGLE
PROJECTI
ON
CSA
BOTTOM OF WALL OPENING FOR CANADIAN STANDARDS ASSOCIATION (CSA)
REQUIREMENTS. INSIDE FLOOR LEVEL CANNOT EXCEED 54mm (218") ABOVE
EXTERIOR SIDEWALK / FLOOR LEVEL AND STILL COMPLY WITH THESE STANDARDS
788mm (31") MAXIMUM HEIGHT FROM EXTERIOR SIDEWALK / FLOOR LEVEL TO
ADA
BOTTOM OF WALL OPENING FOR AMERICANS WITH DISABILITIES ACT (ADA)
61
(
238"
)
REQUIREMENTS. INSIDE FLOOR LEVEL CANNOT EXCEED 76mm (3") ABOVE
31
EXTERIOR SIDEWALK / FLOOR LEVEL AND STILL COMPLY WITH THESE STANDARDS
610 W.O.
31
(24")
(1316")
817mm (3218") MAXIMUM HEIGHT FROM EXTERIOR SIDEWALK / FLOOR LEVEL TO
672 FASCIA
3
16")
(1
BOTTOM OF WALL OPENING FOR CENTRE FOR ENVIRONMENTS (CAE)
CAE
(2638")
REQUIREMENTS. INSIDE FLOOR LEVEL CANNOT EXCEED 105mm (418") ABOVE
EXTERIOR SIDEWALK / FLOOR LEVEL AND STILL COMPLY WITH THESE STANDARDS
PLAN VIEW
FOR ALL THREE STANDARDS ABOVE, WHERE INSIDE FLOOR IS MORE THAN
863mm (34") BELOW THE BOTTOM OF THE WALL OPENING THE OWNER’S G.C.
MUST PROVIDE A SUPPORT PLATFORM.
330mm ( 13") MAXIMUM
WALL THICKNESS IN
AREA OF UNIT
RECOMMENDED SERVICE AREA
MINIMUM SERVICE AREA
AIR VENTS
254
104
(
418"
)
79
(
318"
)
5
)
16"
HOLD
68
(21116")
330
WALL OPENING HEIGHT NOTE #2
VERIFY INSIDE FLOOR AND EXTERIOR SIDEWALK / FLOOR LEVEL
HEIGHTS PRIOR TO CONSTRUCTING WALL OPENING. IF INSIDE
FLOOR LEVEL IS HIGHER OR LOWER THAN EXTERIOR
SIDEWALK / FLOOR, DIMENSION FOR WALL OPENING HEIGHT
MUST BE ADJUSTED ACCORDINGLY AND OPTIMUM OPERATING
HEIGHTS MAY NOT BE MET.
EXTERIOR ELEVATION
MAX. WALL
(13")
HOLD
343
695 SAFE
(1312")
(2738")
889 MINIMUM
(35")
1038
1000 RECOMMENDED
(4078")
(3938")
VERTICAL SECTION
(
7234"
)
1848 M I
NI
M UM
0m m TO 152m m (0"TO 6"
)LEVELI
NG
7
)
16"
(
31
799
191
(712")
(
6234"
)
1594
795
(
31
5
(
28 8"
)
728 W .
O.
1243
(
481516"
)
(
45"
)
1142
40
(1916")
712
235
38
(
112"
)
51
(
2"
)
(
914"
)
TOP OF
MONITOR
TOP
FUNCTION KEY
(
28 58"
)
728 W .
O.
(
3218"
)
184
SEE WALL OPENING DETAIL
FOR RECOMMENDED CLEARANCE
REQUIRED AROUND FASCIA.
815 FASCI
A
(
3938"
)
WI
TH SI
GNAGE PANEL
OPTIONAL CONSUMER BAR
CODE SCANNER (SEE "CAUTION"
LABEL) SEE PAGE 2 OF 4
(
714"
)
(118")
1000 FASCI
A
(
3218"
)
815 FASCI
A
WI
TH SI
GNAGE PANEL
(
3938"
)
INSTALLATION/SERVICE AREA
29
(2638")
1000 FASCI
A
184
(714")
(
28"
)
672 FASCIA
330
(13")
(
10"
)
63
(2716")
SEE W ALL OPENI
NG
HEI
GHT NOTES #1 & #2
FI
LE NO.177460 REV.12
"
ALL DI
M ENSI
ONS AND DESI
GN CRI
TERI
A
SUBJECT TO CHANGE W I
THOUT NOTI
CE"
PAGE 1 OF 4
OUTLINE OF OPTIONAL
ILLUMINATED SIGNAGE PANEL
CONDUIT AND JUNCTION BOX
REQUIREMENTS
1
POWER REQUIREMENTS
THE ATM REQUIRES A SINGLE-PHASE, THREE-WIRE UNSWITCHED POWER RECEPTACLE.
WIRING TO THE RECEPTACLE MUST INCLUDE A THIRD-WIRE EARTH GROUND (CONDUIT
GROUND IS NOT ACCEPTABLE). THE ATM WILL PROVIDE A POWER CORD WITH A COUNTRY
25mm (1") METAL CONDUIT FROM ALARM CONTROL CABINET JUNCTION BOX TO
102mm (4") SQ. X 54mm
(218")
SPECIFIC POWER PLUG. THE POWER SUPPLIED MUST BE AS SPECIFIED BELOW.
DP. JUNCTION BOX (ALL BY OWNER’S E.C.) DIEBOLD
100-127 VAC (+6%, -10%) 50Hz (– 1%) SINGLE-PHASE
TO PROVIDE FLAT COVER WITH TAMPER SWITCH.
100-127 VAC (+6%, -10%) 60Hz (– 1%) SINGLE-PHASE
2
WHEN "SECUROMATIC" AFTER HOUR DEPOSITORY IS TO BE CONNECTED
200-240 VAC (–10%) 50Hz (– 1%) SINGLE-PHASE
TO ATM UNIT, OWNER’S E.C. TO RUN 19mm 3
(4") METAL CONDUIT FROM
200-240 VAC (–10%) 60Hz (– 1%) SINGLE-PHASE
102mm (4") SQ. X 54mm (218") DP. JUNCTION BOX TO AFTER HOUR DEPOSITORY.
3
OWNER’S E.C. TO RUN 19mm
3
(4")
LIQUID TIGHT FLEX METAL CONDUIT OR 19mm
POWER TO THE ATM IS TO BE A DEDICATED SERVICE AND MUST BE PROTECTED BY A
3
(4")
SAFETY QUICK-DISCONNECT DEVICE TO BREAK LINE VOLTAGE (SUCH AS A CIRCUIT
BREAKER AT THE ELECTRICAL SERVICE PANEL. THE QUICK-DISCONNECT DEVICE (OR
RIGID CONDUIT FROM JUNCTION BOX TO CABLE CONNECTING PLATE.
CIRCUIT BREAKER) MUST TURN OFF THE LINE VOLTAGE AT THE FOLLOWING AMPERAGE.
(
DI
M ENSI
ONS I
NI
NCHES)
DI
M ENSI
ONS I
N MI
LLI
M ETRES
4
3
19mm (
4") METAL CONDUIT AND UNSWITCHED ELECTRICAL SUPPLY TO 102mm (4") SQ.
100-127 VAC (+6%, -10%) SERVICE, DISCONNECT AT 20 AMPERES
X 54mm (218") DP. JUNCTION BOX WITH RECEPTACLE WITHIN 2184mm (86") OF
200-240 VAC (–10%) SERVICE, DISCONNECT AT 10 AMPERES
SIDE CONNECTING PLATE. BOTTOM CONNECTION MUST BE COMPENSATED
THE MODULE BULK POWER SUPPLY AND PROCESSOR POWER SUPPLY WILL PROVIDE
ACCORDINGLY (ALL BY OWNER’S E.C.) (SEE POWER REQUIREMENTS).
POWER CONDITIONING TO PREVENT THE TERMINAL FROM MALFUNCTIONING DUE TO
SHORT-TERM AC POWER FLUCTUATIONS AS OUTLINED IN EN61000-4-11.
5
OWNER’S E.C. TO SUPPLY COMPATIBLE RECEPTACLE FOR COUNTRY SPECIFIC
PLUG-IN CONNECTOR SUPPLIED WITH UNIT. POWER CORD LENGTH 2184mm (86")
POWER USAGE
FROM SIDE OF UNIT.
1
MACHINE STATUS
IDLE (NO TRANSACTION)
NOTE:
OR BULK NOTE) IN PROGRESS
PLATE. ( LENGTH OF ELECTRICAL POWER CABLE PROVIDED WITH UNIT).
RAPID PROCESSING
LOCATE IN AN EASILY ACCESSIBLE AREA.
TRANSACTION IN PROGRESS
2
HEATER
2
WITH
HEATER
190 WATTS
690 WATTS
255 WATTS
755 WATTS
285 WATTS
785 WATTS
375 WATTS
875 WATTS
550 WATTS
1,050 WATTS
640 WATTS
1,140 WATTS
TRANSACTION (DISPENSE
JUNCTION BOXES MUST BE LOCATED WITHIN 2184mm ( 86") OF CONNECTING
WITH
1
BOXES CAN BE FLUSH MOUNTED WITH CONCEALED CONDUIT FOR
NEW CONSTRUCTION OR BOXES CAN BE SURFACE MOUNTED
CONFIGURATION
WITH EXPOSED CONDUIT FOR EXISTING CONSTRUCTION.
PROCESSOR, COLOR LCD CONSUMER DISPLAY, MOTORIZED CARD READER, JOURNAL
1
PRINTER, 80mm THERMAL RECEIPT PRINTER, STANDARD DEPOSITORY AND 5 HIGH AFD.
PHYSICAL SECURITY
2
THE SECURITY SAFE MEETS THE BANK PROTECTION ACT 82 STAT 295,
PROCESSOR, SVD LCD CONSUMER DISPLAY, MOTORIZED CARD READER, JOURNAL PRINTER,
80mm THERMAL RECEIPT PRINTER, IDM, 5 HIGH AFD, SIGNAGE AND BULK NOTE ACCEPTOR.
12 USC 882, AND MEETS THE ATTACK TEST PER UL 291-15. THE SAFE DOOR
RAPID PROCESSING - SYSTEMS CONFIGURED FOR SIMULTANEOUS IDM (INTELLIGENT
HAS A POSITIVE RELOCKING FEATURE. THE SAFE DOOR SHOULD BE CONTROLLED
DEPOSITORY MODULE) AND ENA (ENHANCED NOTE ACCEPTOR) OR IDM AND BNA (BULK
BY A MINIMUM OF A GROUP 2M UL LISTED COMBINATION LOCK WITH OR WITHOUT
NOTE ACCEPTOR) OPERATIONS.
KEYLOCKING DIAL CAPABILITY OR OPTIONAL ELECTRONIC LOCK.
THE POWER USE DEPENDS ON THE NUMBER AND TYPE OF DEVICES PRESENT IN
THE ATM, AND THE TYPE OF TRANSACTION THE ATM IS PERFORMING.
ALARM PROTECTION
THE UL-LISTED SAFE IS EQUIPPED WITH A BASIC ALARM SENSOR PACKAGE. THE
BASIC PACKAGE INCLUDES A SAFE DOOR OPEN SWITCH, ALARM SHUNTING SWITCH,
PROJECTI
ON
1
2,677 BTU/HR DISPENSE WITH HEATER
648 BTU/HR IDLE WITHOUT HEATER
3,580 BTU/HR RAPID PROCESSING WITH HEATER
2
2,984 BTU/HR BULK NOTE WITH HEATER
870 BTU/HR IDLE WITHOUT HEATER
3,890 BTU/HR RAPID PROCESSING WITH HEATER.
BUILDING AIR PRESSURE
BUILDING AIR PRESSURE DIFFERENCES AT THE ATM INSTALLATION LOCATION
AFFECT THE INFILTRATION OF OUTSIDE AIR AND ACCOMPANY DIRT. THE ATM WILL
OPERATE THROUGH ITS FULL RANGE OF FASCIA TEMPERATURES -34” C TO 54” C
(-29” F TO 129” F) WITH ZERO (STATIC) OR POSITIVE AIR PRESSURE DIFFERENTIAL
OPERATING ENVIRONMENT
(MEASURED FROM THE INSIDE TO THE OUTSIDE OF THE BUILDING AT THE ATM
10” C TO 38” C (50” F TO 100” F)
SAFE LOCATION
INSTALLATION LOCATION). IF STATIC OR POSITIVE AIR PRESSURE CANNOT BE
RELATIVE HUMIDITY ( NON-CONDENSING )
MAINTAINED, THE FASCIA LOWER LIMIT TEMPERATURE IS -20” C (-4” F). THE
20 TO 80% AT 32” C (90” F),
MAXIMUM NEGATIVE AIR PRESSURE ALLOWED IS 0.05" H O.
2
20 TO 55% AT 38” C (100” F)
-34” C TO 54” C (-30” F TO 130” F)
RELATIVE HUMIDITY 15 TO 100%
FASCIA LOCATION
SIGNAL CABLE RUN CONSTRAINTS
THE FOLLOWING CHART ITEMIZES THE PHYSICAL SPACING REQUIREMENTS OF THE
SIGNAL CABLE RUN WITH RESPECT TO OTHER POWER AND ELECTRICAL EQUIPMENT
CABLE RUN.
WEIGHT OF UNIT
696kg (1,535 LBS.)
SEPARATION FROM OTHER CABLES
BELOW 2 KVA
2-5 KVA
ABOVE 5 KVA
127mm (5")
127mm (5")
127mm (5")
UNSHIELDED POWER LINE OR ELECTRICAL EQUIPMENT
127mm (5")
305mm (12")
UNSHIELDED POWER LINES OR ELECTRICAL EQUIPMENT
64mm (212")
152mm (6")
30mm (1316")
76mm (3")
TYPE OF ELECTRICAL RUN
FLUORESCENT, NEON OR INCANDESCENT
LIGHTING FIXTURES
POWER LINES IN GROUNDED CONDUIT WITH SIGNAL
CABLES IN GROUNDED CONDUIT
305mm (12")
152mm (6")
SIGNAL CABLE INSTALLATION CONSTRAINTS
RELATIVE CARE IS REQUIRED WHEN INSTALLING SIGNAL CABLES IN CONDUITS. UNLIKE POWER AND
1594
64
51
(212")
(2")
(
6234"
)
0m m TO 152m m (0"TO 6"
)LEVELI
NG
(2634")
104
80
1
4
180
330
(718")
(13")
(
318"
)
40
AIR VENTS
(
418"
)
19
WITHSTAND AS MUCH STRAIN IN INSTALLATION.
3
(
)
4"
LIGHTING CABLE, SIGNAL CABLES HAVE SMALL CONDUCTORS AND LIGHT INSULATION AND WILL NOT
679
"
ALL DI
M ENSI
ONS AND DESI
GN CRI
TERI
A
SUBJECT TO CHANGE W I
THOUT NOTI
CE"
CAUTION LABEL
610mm (2’-0")
(
1916"
)
PAGE 2 OF 4
WITH SIGNAL CABLES ENCLOSED IN GROUNDED CONDUIT
FI
LE NO.177460 REV.12
THI
RD ANGLE
AND RATE-OF-RISE HEAT SENSOR.
HEAT OUTPUT CONFIGURATION
AIR VENTS
2
4
1
5
3
149
508
343
(578")
(20")
(1312")
38
(112")
1038
(4078")
INTERIOR ELEVATION
VERTICAL SECTION
OPTEVAfi 760 ADVANCED FUNCTION WALK-UP ATM
THROUGH THE WALL
R
5 HIGH WITH 13mm 1
(2") SAFE
CALL 1-800-999-3600
WALL OPENING DETAIL
SUPPORT PLATFORM
AS REQUIRED (NOT BY
DIEBOLD)
NOTCH REQUIRED IN WALLS
610 W.O.
OVER 191mm (712")
(24")
(
2858"
)
(
2858"
)
728 W .
O.
82
191
101
1
(7 2")
(4")
610 W.O.
3
INTERIOR FLOOR LEVEL OR
TOP OF SUPPORT PLATFORM
BY THE OWNER’S G.C.
610 W.O.
712m m (
28"
)M I
N.
350
(13 4")
863m m (
34"
)M AX.
SEE W ALL OPENI
NG
HEI
GHT NOTES #1 & #2
142
(24")
(
558"
)
MAX.
142
(
43"
)
(314")
(
558"
)
1092 SHOW N
728 W .
O.
(3314")
(
DI
M ENSI
ONS I
NI
NCHES)
DI
M ENSI
ONS I
N MI
LLI
M ETRES
845 SHOWN
PROJECTI
ON
PLAN VIEW
INTERIOR ELEVATION
330
MAX. WALL IN
AREA OF UNIT
(13")
DETAIL FOR WALLS OVER 191mm ( 712")
SECTION
WALL OPENING HEIGHT NOTE #1:
766mm
330mm (13") MAX. WALL
THICKNESS IN AREA
OF UNIT
CSA
(3018")
MAXIMUM HEIGHT FROM EXTERIOR SIDEWALK / FLOOR LEVEL TO
BOTTOM OF WALL OPENING FOR CANADIAN STANDARDS ASSOCIATION (CSA)
REQUIREMENTS. INSIDE FLOOR LEVEL CANNOT EXCEED 54mm (218") ABOVE
EXTERIOR SIDEWALK / FLOOR LEVEL AND STILL COMPLY WITH THESE STANDARDS
788mm (31") MAXIMUM HEIGHT FROM EXTERIOR SIDEWALK / FLOOR LEVEL TO
ADA
BOTTOM OF WALL OPENING FOR AMERICANS WITH DISABILITIES ACT (ADA)
REQUIREMENTS. INSIDE FLOOR LEVEL CANNOT EXCEED 76mm (3") ABOVE
EXTERIOR SIDEWALK / FLOOR LEVEL AND STILL COMPLY WITH THESE STANDARDS
817mm (3218") MAXIMUM HEIGHT FROM EXTERIOR SIDEWALK / FLOOR LEVEL TO
BOTTOM OF WALL OPENING FOR CENTRE FOR ENVIRONMENTS (CAE)
CAE
PAGE 3 OF 4
*
FOR ALL THREE STANDARDS ABOVE, WHERE INSIDE FLOOR IS MORE THAN
863mm (34") BELOW THE BOTTOM OF THE WALL OPENING THE OWNER’S G.C.
MUST PROVIDE A SUPPORT PLATFORM.
OPENING FOR PROPER INSTALLATION
OF THE ATM
*724
1
(28 2")
610 W.O.
*57
(214")
0
(24")
LINE OF FASCIA WITH
SIGNAGE PANEL
LINE OF FASCIA
728 W .
O.
(
28 58"
)
(
2858"
)
728 W .
O,
1
870
(
34 4"
)
(
2858"
)
728 W .
O.
712m m (
28"
)M I
N.
OPENING FOR PROPER INSTALLATION
OF ATM
863m m (
34"
)M AX.
*CLEARANCE REQUIRED AROUND WALL
WALL OPENING HEIGHT NOTE #2
SEE W ALL OPENI
NG
HEI
GHT NOTES #1 & #2
*
*
SEE W ALL OPENI
NG
HEI
GHT NOTES #1 & #2
65
*
(
3"
)
77
1054
*
(
212"
)
*
(
1014"
)
259
(214")
0
*57
(
4112"
)
"
ALL DI
M ENSI
ONS AND DESI
GN CRI
TERI
A
SUBJECT TO CHANGE W I
THOUT NOTI
CE"
REQUIREMENTS. INSIDE FLOOR LEVEL CANNOT EXCEED 105mm (418") ABOVE
EXTERIOR SIDEWALK / FLOOR LEVEL AND STILL COMPLY WITH THESE STANDARDS
PROVIDE VERTICAL AND HORIZONTAL
FLAT PLUMB SURFACE AROUND WALL
FI
LE NO.177460 REV.12
THI
RD ANGLE
(24")
191
(712")
MAX.
330
VERIFY INSIDE FLOOR AND EXTERIOR SIDEWALK / FLOOR LEVEL HEIGHTS PRIOR TO
CONSTRUCTING WALL OPENING. IF INSIDE FLOOR LEVEL IS HIGHER OR LOWER THAN
EXTERIOR SIDEWALK / FLOOR, DIMENSION FOR WALL OPENING HEIGHT MUST BE
ADJUSTED ACCORDINGLY AND OPTIMUM OPERATING HEIGHTS MAY NOT BE MET.
EXTERIOR ELEVATION
MAX. WALL
(13")
VERTICAL SECTION
FLOOR LEVEL OR TOP
OF SUPPORT PLATFORM
BY THE OWNER’S G.C.
ANCHOR BOLT
RECOMMENDED ANCHOR BOLT SIZE - M20 19mm 3
(4") (NOT SUPPLIED WITH ATM).
768 SAFE
CABLE ENTRY
(3014")
35
698
35
(138")
(2712")
(138")
465
303
(18516")
(111516")
ELECTRICAL AND DATA CABLING ENTERS THE ATM THROUGH A CABLE ENTRY
OPENING ON THE SIDE OF THE SAFE. CABLES ENTERING THE ATM PASS THROUGH
THE POWER CABLE PLATE WHICH IS ATTACHED TO THE INSIDE WALL OF THE
SAFE OVER THE CABLE ENTRY OPENING. CABLING CAN ENTER FROM THE
SIDE OR OPTIONALLY FROM UNDER THE ATM. THE CABLE ENTRY OPENING
IS ON THE RIGHT SIDE OF THE SAFE AS VIEWED FROM THE REAR OF THE ATM.
417
7
(
3 8"
)
99
222
29mm (118") DIA. HOLE FOR
ALARM CABLES (SIDE ENTRY)
(
2738"
)
9
)
16"
695 SAFE
(
1534"
)
400
AND DATA CABLES
(SIDE ENTRY)
73
7
1
2
99
1
2
(
278"
)
38
OPENING FOR POWER CORD
POWER CABLE PLATE
(
112"
)
508
497
2
(
19
2
(
3 8"
)
38
(
112"
)
SEE CABLE ENTRY NOTE
PROJECTI
ON
PLAN/SECTION SAFE FLOOR
1
9
(4) 14mm (
16") DIA. LEVELING LEG HOLES
2
(4) 25.4mm (1") DIA. FLOOR MOUNTING HOLES
NOTE:
RECOMMENDED SERVICE AREA
SHOWN IS THE MINIMUM/RECOMMENDED AREA REQUIRED FOR INSTALLATION AND
SERVICE. DIMENSIONS SHOWN MAY BE INCREASED WHEREVER POSSIBLE TO
IMPROVE INSTALLATION AND SERVICE ACCESS. USE OF ANY AREA LESS THAN THE
RECOMMENDED AREA MAY RESULT IN AN INCREASE IN INSTALLATION AND SERVICE
TIME. CONSULT WITH DIEBOLD INSTALLATION/SERVICE BRANCH FOR SPECIAL
BUILDING CONDITIONS.
1604
MINIMUM SERVICE AREA
ALL ELECTRICAL AND DATA CABLES
MUST ENTER UNIT IN THIS AREA
1
16")
(63
1303
453
152
794
357
(6")
(3114")
(14")
13
16")
(17
(
434"
)
(
6"
)
3
121
152
1000
(
39 8"
)
7
709
(
27 8"
)
330
(
13"
)
(6")
M AX.
W ALL
330
PLAN VIEW
MINIMUM SERVICE AREA
(
13"
)
51
(2")
W ALL
51
(2")
M AX.
(14")
1
(
6"
)
2039
121
(
434"
)
152
152
(
2778"
)
(
13"
)
357
1
TOP CHASSIS
SERVICE DOOR
(
80 4"
)
TOP CHASSIS
SERVICE DOOR
(
35"
)
889
708
330
1927
794
(31 4")
CHEST DOOR
CHEST DOOR
(
7578"
)
"
ALL DI
M ENSI
ONS AND DESI
GN CRI
TERI
A
SUBJECT TO CHANGE W I
THOUT NOTI
CE"
PAGE 4 OF 4
(5114")
FI
LE NO.177460 REV.12
THI
RD ANGLE
1
(
834"
)
149
(
578"
)
1
(
20"
)
(
DI
M ENSI
ONS I
NI
NCHES)
DI
M ENSI
ONS I
N MI
LLI
M ETRES
(16716")
PLAN VIEW
RECOMMENDED SERVICE AREA