RENOIR II
Cat. Nos. AWRMG, AWSMG, AWSMT, AWWMG, AWWMT
Environmental Conditions: 0-40º C, 0-90% non-condensing humidity.
Input Power Rating 110-277VAC, 60Hz only (incandescent non-neutral model is 120V input only)
PK-93824-10-00-2A-X2
INSTALLATION
WARNINGS AND CAUTIONS:
• TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE
ELECTRICAL CODES AND REGULATIONS.
• IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT
AN ELECTRICIAN.
• DO NOT GANG VERTICALLY.
• ONLY INSTALL FOR THE ALLOWED LOAD TYPES (SEE FIGURE 5). INSTALLATION
FOR ANY OTHER LOAD TYPE WILL VOID WARRANTY AND POSSIBLY CAUSE
DAMAGE TO THIS DEVICE AND/OR CONNECTED EQUIPMENT.
• USE THIS DEVICE WITH COPPER OR COPPER CLAD WIRE ONLY.
Features and Operation:
• Turn Dimmer ON or OFF – Pressing the switch will turn the dimmer ON if the dimmer is
OFF. If the dimmer is ON, pressing the switch will turn the dimmer OFF.
• Set Dimmer Level – Adjust the knob or slider to set the desired output level. When the
dimmer turns ON, the dimmer always turns ON to the level set by the slider or knob.
• Set Cutoff Level – The cutoff level is the lowest voltage the dimmer will output before
shutting off. To set the cutoff level, adjust the knob or slider to the cutoff level you desire,
then push and hold the button for 5 seconds. The dimmer will turn OFF and then back
ON again indicating that the new cutoff level has been set. To reset the cutoff level to 0,
lower the slider all the way down, then push and hold the button for 5 seconds. If your
load type is flickering , not turning on, or suffering from any other erratic behavior at the
minimum setting, raising the cutoff level may eliminate the problem.
• Preset Operation – While dimmer is off, set level of dimmer. Then press button. The
dimmer will turn on at the set level.
• Power Restore – Upon restoration of power, the dimmer turns ON to the state it was in
at the time of power loss.
• 5-Way Operation – Link together 2, 3, 4, or 5 dimmers for multi-way dimming.
• LED Locator – At the bottom of the switch is an LED locator. This locator illuminates
when the dimmer is OFF so you can find the dimmer in the dark.
• Remote Control – If you are using a remote, the operation at the remote is identical
to the operation at the master. A slight reaction delay may be noticed if operating level
changes very quickly.
• Service Switch – Some units have a service switch which must be used to disconnect
the load when replacing lamps. The breaker should be disconnected when performing
any luminaire, ballast, or other circuit service other than lamp replacement.
Load
Disconnected
Load
Connected
Load
Connected
Load
Disconnected
Service Switch
Service Switch
Rotate far left
for OFF, rotate
far right for ON
Installation Instructions:
1. WARNING: TO AVOID FIRE, SHOCK OR DEATH; TURN OFF POWER AT CIRCUIT
BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
2. Remove existing wall plate and switch, if applicable.
3. Remove 5/8” (1.6 cm) of insulation from each circuit conductor. Make sure the ends of
wires are straight.
4. Connect wires per WIRING DIAGRAM on device as follows: Twist strands of each lead
tightly together and, with circuit conductors, push firmly into appropriate wire connector.
Screw connectors on clockwise making sure no bare conductors show below the wire
connectors. Secure each connector with electrical tape.
5. Installation may now be completed by carefully positioning all wires to provide room
in outlet box for dimmer. Mount dimmer into box with mounting screws supplied. Snap
faceplate into place.
6. Install device control push button and control assembly (see below).
7. Restore power at circuit breaker or fuse. Installation is complete.
8. Test Dimmer operation.
Align flats when
installing knob
Load after Remote Dimmer/Switch and Master Dimmer/Switch
Load
White
Neutral (White)
– Run a separate neutral wire
for each dimming circuit
Load
NOT
X– DO
share
neutral
wires
White
Hot
Hot
Dimmed Hot
Ground
Ground
Traveler
Ground
Neutral
Center tab in opening
Neutral
Fin break off points
LOAD
Neutral
Remote Dimmer/Switch
Master Dimmer/Switch
Load in between Master Dimmer/Switch and Remote Dimmer/Switch
Hot
Neutral
Ground
Traveler
Rotary dimmer
Slide dimmer
Hot
Dimmed Hot
Ground
Ground
Neutral
Neutral
LOAD
Multi-Gang Installations:
A multi-ganged installation exists when multiple devices are installed in the same back box. In
multi-gang installations, the following may be required:
1. Dimmer location
2. Dimmer de-rating
3. Fin removal
4. Back box size
5. Use of joiner bars for adjacent dimmers. 6. Narrow dimmers must always be installed in between wide dimmers.
NOTE: TEST FIT DIMMER INSTALLATION WITH THE WALL PLATE PRIOR TO BREAKING
FINS OR INSTALLING DIMMERS TO ENSURE YOU UNDERSTAND ALL REQUIREMENTS.
Number & Type of NARROW
Slide Dimmer
• These devices are designed for installation into a 2" x 3" (5.08 cm x 7.62 cm) single
gang or multi-gang device back box. 2-1/2" (6.35 cm) or deeper back boxes are
required. These devices are not designed for a multi-gang field configured box. In some
installations where conduit entry is from the side, or, in multi-gang installations where
nipples between two adjacent boxes are used, deeper back boxes may be necessary.
Test fit installation prior to rough-in.
• Installation of multiple devices into a single box may require de-rating and other specific
installation provisions. Reference Multi-Gang Installations for more details.
• As dimmers vent top/bottom, dimmers should not be installed vertically (one over the other).
• To avoid flickering, flashing, or lights on one dimmer adjusting when another dimmer’s
level is changed, do not share neutrals. Run separate neutrals for each load circuit back
to the dimmer.
Neutral (White)
Break off these fins
Figure 2 - Fin Removal
The Renoir II product line supports up to 5-way dimming. Any combination of Dimmers,
Switches, or Remotes are supported with a MAXIMUM OF 5 DEVICES. Total run length
from end to end is MAXIMUM 250 FEET. Remotes require Uncontrolled Hot, Neutral, &
Ground for proper operation. One traveler wire is to run in between all masters and remotes.
Remotes draw 15mA power (ea) from the Dimmer to which they are connected.
NOTE: Remote Hot/Neutral should ideally be fed from the same circuit as the Master. If this
is not possible, ensure that the master and remote are both fed from the same phase.
Master Dimmer/Switch
DO NOT Break off these fins
Dimmed Hot
Neutral
0
0
Backbox - # Gangs
Wallplate Part #
1
Device Configuration
Wallplate Part #
Backbox - # Gangs
2
Device Configuration
Wallplate Part #
3
Backbox - # Gangs
Device Configuration
Wallplate Part #
Number & Type of WIDE
1
Device Configuration
Backbox - # Gangs
1
1
2
3
4
6**
W
W+W
W+W+W
AWP0F-01x
AWP0F-02x
AWP0F-03x
3
5 or 6
8
N
W+N
W+N+W
W+W+N+W
AWP0F-10x
AWP0F-11x
AWP0F-12x
AWP0F-13x
2
4
6
8
N*+*N
W+N*+*N
W+N*+*N+W
W*+*W+N*+*N+W
AWP00-20x
AWP00-21x
AWP00-22x
AWP00-23x
4**
6**
7
Ground
W+N+N+N
W+N*+N*+*N+W
W*+*W+N*+N*+*N+W
AWP00-30x
AWP00-31x
AWP00-32x
AWP00-33x
1. Find the cells that correspond to your application by identifying the row with the number of wide
heatsink dimmers you have, and the columns that correspond to the number of narrow heat sink
dimmers you have. In the cell you’ll find the following:
2. The number indicates the number of “Gangs” required.
3. The letters under the number indicate the order dimmers should be installed, N=narrow, W=wide.
4. -W* = right fin break-off on wide dimmer, N* = right fin break-off on narrow dimmer.
-*W = left fin break-off on wide dimmer, *N = left fin break-off on narrow dimmer.
-*W* = fin break-off on both sides of wide dimmer, *N* = fin break-off on both sides of narrow dimmer.
5. '** indicates that use of jumper bars is required. Jumper bars can be found in the kit with the faceplate.
6. Replace 'x' in the faceplate part number with the desired color: W=White, I=Ivory, A=Almond, T=Light
Almond, E=Black, G=Gray, K=24K Gold, L=Satin Stainless, R=Antique Bronze, B=Brushed Brass.
NOTE: Metal finishes are not available on custom face plates.
Fin Removal:
Narrow/Narrow
When it is desired to install dimmers in as small a space as possible, all inside fins of like sized,
adjacent dimmers can be broken off. Figures 1 & 2 show how to break off fins and the specific order
in which multiple dimmers must be installed in multi-gang installations.
LOAD
Hot
Hot
Hot
Hot
Hot
Ground
Ground
Ground
Ground
Ground
Neutral
Joiner Bar
Neutral
Neutral
Traveler
Master
Dimmer/Switch
Joiner Bar
Traveler
Remote
Dimmer/Switch
Neutral
Neutral
Traveler
Remote
Dimmer/Switch
Traveler
Remote
Dimmer/Switch
Remote
Dimmer/Switch
Maximum 5 Devices, Dimmers or Remotes
Maximum 250 feet
Multiple Dimmer/Switches and Remote Dimmer/Switches
9
N+N+N
Remote Dimmer/Switch
Multiple Remote Dimmer/Switches
Figure 3 - Joiner Bar
NOTE: Basic configurations shown. For additional multi-gang configurations, see Figure 5A.
Installation Requirements:
Black
To determine the required back-box size in multi-gang installations, reference Figure 1. In
applications where the dimmers do not line up with back box device mounting holes, use
joiner bars to join the dimmers together. Reference Figures 1 & 3.
Multi-Way Dimming:
Back Box Size Chart
Rotary Dimmer
Hot (Black)
Back Box Size & Joiner Bars:
Break off these fins
Basic Configurations
Hot (Black)
When fins are broken, some dimmer models must be de-rated. Reference Figure 5 to
determine the dimmer ratings when 0, 1, or 2 fins are removed.
Back view of dimmers shown
Figure 1
Black
De-ratings:
Dimmed Hot
Neutral
Ground
Wide/Narrow
Dimmed Hot
LOAD
Neutral
Ground
LOAD
Wide/Wide
Hot
Hot
Hot
Hot
Hot
Ground
Ground
Ground
Ground
Ground
Neutral
Figure 4 - Second Single Gang Device Box
Four-gang wallbox
Single-gang wallbox
Neutral
Traveler
Master
Dimmer/Switch
3-1/2" deep
back box is
required
Neutral
Traveler
Remote
Dimmer/Switch
Neutral
Neutral
Traveler
Dimmer/Switch
Traveler
Remote
Dimmer/Switch
Maximum 5 Devices, Dimmers or Remotes
Maximum 250 feet
3/4" space (use chase nipple)
Remote
Dimmer/Switch
Figure 5 - Model, Voltage, Allowed Loads, Current and De-rating Charts
INCANDESCENT DIMMER - 110-277VAC/VCA, 60Hz
INCANDESCENT NON-NEUTRAL” DIMMER - 110-277VAC/VCA, 60HZ
FLUORESCENT - 2 WIRE PHASE CONTROL - 120-277VAC/VCA, 60HZ
ELECTRONIC LOW VOLTAGE - 120-277VAC/VCA, 60HZ
Use only for permanently installed luminaire of load type: Incandescent, Tungsten, Inductive
Transformer (ex: magnetic low voltage), LED fixtures with drivers with incandescent control input.
CAUTION: To reduce risk of overheating and possible damage to other equipment, do not
install to control a receptacle, a motor-operated appliance, or a fluorescent lighting luminaire.
Use only for permanently installed luminaire of load type: Incandescent, Tungsten, Inductive
Transformer (ex: magnetic low voltage), LED fixtures with drivers with incandescent control input.
CAUTION: To reduce risk of overheating and possible damage to other equipment, do not
install to control a receptacle, a motor-operated appliance, or a fluorescent lighting luminaire.
Use only for control of electronic ballasted luminaires. Intended for Advance Mark 10,
Lutron Tu-Wire, or Sylvania Quicktronic Power Sense ballasts. CAUTION: To reduce
risk of overheating and possible damage to other equipment, do not install to control a
receptacle, a motor-operated appliance, or a transformer supplied appliance.
Use only for permanently installed luminaire of load type: Incandescent, Tungsten, or
Electronic Transformer. CAUTION: To reduce risk of overheating and possible damage
to other equipment, do not install to control a receptacle, a motor-operated appliance, or a
fluorescent lighting luminaire.
INCANDESCENT
AWRMG-MA_
AWSMG-MA_
AWSMT-MA_
AWRMG-MB_
AWSMG-MB_
AWRMG-MC_
AWSMG-MC_
AWRMG-MD_
AWSMG-MD_
AWSMT-MB_
AWSMT-MC_
AWSMT-MD_
Amps
VA @ 120V
0 FINS
REMOVED
VA @ 230V
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
1 FIN
REMOVED
5.0
600
12.5
1500
3680
4432
8.3
1000
1917
2308
12.5
1500
2875
3463
16.0
1920
3680
4432
AWRMG-IC_
AWSMG-IC_
M
I
L
E
1495
1801
1219
1468
12.3
1476
AWRMG-ID_
AWSMG-ID_
AWSMT-IB_
2829
3407
12.3
1476
13.5
1620
3105
3740
7.0
840
2829
3407
5.5
660
1610
1939
10.2
1224
1265
1524
8.7
1044
2346
2825
13.0
1560
AWSMT-IC_
AWSMT-ID_
600
VA @ 120V
Amps
VA @ 120V
Amps
VA @ 120V
Amps
VA @ 120V
Amps
VA @ 120V
Amps
VA @ 120V
Amps
VA @ 120V
FLUORESCENT
2 WIRE PHASE CONTROL
Amps
AWRMG-XA_
VA @ 120V
AWSMG-XA_
VA @ 230V
AWSMT-XA_
VA @ 277V
Amps
VA @ 120V
AWRMG-XB_
VA @ 230V
AWSMG-XB_
2 FINS
REMOVED
8.3
1000
6.5
780
12.5
1500
16.0
1920
8.3
1000
12.5
1500
16.0
1920
5.3
636
12.3
1476
12.3
1476
5.5
660
8.7
1044
11.1
1332
13.5
1620
7.0
840
10.2
1224
13.0
1560
AWRMG-XC_
AWSMG-XC_
AWRMG-XD_
AWSMG-XD_
Use only for permanently installed electronic ballasted luminaire of fluorescent, HID, or LED
load type with driver/ballast setup for 0-10Vdc sinking control. Dimmer will sink maximum
75mA. Intended for the control of Advance Mark 7, Universal Sumper Dim, Lutron TVE,
Leviton Sector, or Sylvania Quicktronic Powersense ballast. CAUTION: To reduce risk of
overheating and possible damage to other equipment, do not install to control a receptacle,
a motor-operated appliance, or a transformer supplied appliance.
FLUORESCENT
0-10VDC SINKING CONTROL
Amps
AWRMG-7D_
VA @ 120V
AWRMT-7D_
AWSMG-7D_
VA @ 230V
AWSMT-7D_
VA @ 277V
2553
3601
1 FIN
REMOVED
5.0
FLUORESCENT - 0-10VDC SINKING CONTROL - 120-277VAC/VCA, 60HZ
2001
2410
11.1
1332
2990
Amps
0 FINS
REMOVED
Y
R
INA
AWRMG-IB_
AWSMG-IB_
5.3
636
PR
16.0
1920
2875
3463
INCANDESCENT NON-NEUTRAL
AWRMG-IA_
AWSMG-IA_
AWSMT-IA_
1150
1385
6.5
780
8.3
1000
1917
2308
2 FINS
REMOVED
3075
0 FINS
REMOVED
1 FIN
REMOVED
16.0
1920
3680
4432
AWSMT-XB_
AWSMT-XC_
2 FINS
REMOVED
AWSMT-XD_
0 FINS
REMOVED
1 FIN
REMOVED
5.0
600
1150
1385
6.5
780
8.3
1000
1917
2308
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
16.0
1920
3680
4432
Amps
VA @ 120V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
8.3
1000
1917
2308
12.5
1500
VA @ 230V
VA @ 277V
Amps
VA @ 120V
2875
3463
16.0
1920
VA @ 230V
VA @ 277V
3680
4432
12.5
1500
2875
3463
1495
1801
13.5
1620
3105
3740
7.0
840
1610
1939
10.2
1224
2346
2825
13.0
1560
2990
3601
2 FINS
REMOVED
ELECTRONIC LOW VOLTAGE
Amps
VA @ 120V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
AWRMG-EA_
AWSMG-EA_
AWSMT-EA_
5.3
636
AWRMG-EB_
AWSMG-EB_
1219
1468
12.3
1476
AWSMT-EB_
2829
3407
12.3
1476
2829
3407
0 FINS
REMOVED
8.3
1000
1917
2308
8.3
1000
VA @ 230V
VA @ 277V
1917
2308
1 FIN
REMOVED
5.0
600
1150
1385
2 FINS
REMOVED
8.2
984
1886
2271
6.8
816
7.5
900
1564
1884
1725
2078
FAN SPEED CONTROLS, FULL VARIABLE, FULL QUIET - 120-277VAC/VCA, 60HZ
For use with any fan, up to 5A. For use with any quantity of ceiling paddle fans up to
maximum current rating.
FAN SPEED CONTROLS
FULL VARIABLE, FULL QUIET
Amps
AWRMG-QA_
VA @ 120V
AWSMG-QA_
VA @ 230V
AWSMT-QA_
VA @ 277V
Amps
VA @ 120V
AWRMG-QB_
AWSMG-QB_
VA @ 230V
VA @ 277V
Amps
VA @ 120V
AWSMT-QB_
VA @ 230V
VA @ 277V
5.5
660
1265
1524
8.7
1044
2001
2410
11.1
1332
2553
3075
0 FINS
REMOVED
8.3
1000
1917
2308
8.3
1000
1917
2308
1 FIN
REMOVED
5.0
600
1150
1385
6.5
780
2 FINS
REMOVED
5.3
636
1495
1801
7.0
840
1610
1939
1219
1468
5.5
660
1265
1524
FLUORESCENT - 3 WIRE PHASE CONTROL 120-277VAC/VCA, 60HZ
1
2
SWITCHES - 120-277VAC/VCA, 60HZ
Use only for resistive, incandescent, inductive,
ballast or motor load.
SWITCHES
Amps
HP @ 120V
HP @ 230V
AWWMG-0D_
HP @ 277V
AWWMT-0D_
FLA
VA @ 120V
VA @ 230V
VA @ 277V
0, 1 or 2 FINS
REMOVED
15.0
1HP
1.5HP
1.5HP
12.0
1800
3450
4150
3
Device Configuration
1
N/A
Wallplate Part #
Backbox - # Gangs
Device Configuration
1
Device Configuration
Wallplate Part #
3
4
4
6**
9
W
W+W
W+W+W
W+W+W+W
AWP0F-02x
AWP0F-03x
AWP0F-04x
W*+*W
W*+*W*+*W
W*+*W*+*W*+*W
AWP00-02x
AWP00-03x
AWP00-04x
5 or 6
8
not supported
1
2
AWP0F-01x
Wallplate Part #
Backbox - # Gangs
Number & Type of WIDE
3
3
W+N+W
W+W+N+W
W+W+N+W+W
AWP0F-10x
AWP0F-11x
AWP0F-12x
AWP0F-13x
AWP0F-14x
not supported
Device Configuration
Wallplate Part #
Device Configuration
Wallplate Part #
Backbox - # Gangs
Device Configuration
Wallplate Part #
Backbox - # Gangs
5+1** or 7
9
W*+*W+N+W
W*+*W+N+W*+*W
AWP00-13x
AWP00-14x
10
12
1+1
3+1, or 5
W+N+N
W+N+N+W
W+W+N+N+W
W+W+N+N+W+W
AWP0F-20x
AWP0F-21x
AWP0F-22x
AWP0F-23x
AWP0F-24x
N*+*N
W+N*+*N
W+N*+*N+W
W*+*W+N*+*N+W
W*+*W+N*+*N+W*+*W
AWP00-20x
AWP00-21x
AWP00-22x
AWP00-23x
AWP00-24x
4**
6**
9
11
N+N
2
4
6
8
4
11
W+N
7
Additional Configurations
7
N
Backbox - # Gangs
Backbox - # Gangs
5
Figure 5A - continued
6
10
14
N+N+N
W+N+N+N
W+N+N+N+W
W+W+N+N+N+W
W+W+N+N+N+W+W
AWP0F-30x
AWP0F-31x
AWP0F-32x
AWP0F-33x
AWP0F-34x
Device Configuration
3
5
7
9
N*+*N*+*N W+N*+*N*+*N W+N*+*N*+*N+W W*+*W+N*+*N*+*N+W W*+*W+N*+*N*+*N+W+W
Wallplate Part #
AWP0F-30x
AWP00-31x
AWP00-32x
AWP00-33x
Device Configuration
Wallplate Part #
Backbox - # Gangs
11
5
Remove Fins Fins Left On Remove Fins Fins Left On Remove Fins Fins Left On
0
Backbox - # Gangs
0
Number & Type of NARROW
Additional Configurations
Remove Fins Fins Left On Remove Fins Fins Left On Remove Fins Fins Left On Remove Fins Fins Left On
FLUORESCENT
0, 1 or 2 FINS
3 WIRE PHASE CONTROL
REMOVED
Amps
5.0
AWRMG-HA_ VA @ 120V
600
AWSMG-HA_
1150
VA @ 230V
AWSMT-HA_
1385
VA @ 277V
Amps
8.3
AWRMG-HB_ VA @ 120V
1000
AWSMG-HB_
1917
AWSMT-HB_ VA @ 230V
2308
VA @ 277V
Amps
12.5
AWRMG-HC_ VA @ 120V
1500
AWSMG-HC_
2875
AWSMT-HC_ VA @ 230V
VA @ 277V
3463
Amps
16.0
AWRMG-HD_ VA @ 120V
1920
AWSMG-HD_
3680
AWSMT-HD_ VA @ 230V
VA @ 277V
4432
Figure 5A
Number & Type of NARROW
Use only for control of electronic ballasted luminaires.
Intended for Lutron Eco-10, Hi-Lume, or Hi-Lume 3D
Fluorescent Ballasts. CAUTION: To reduce risk of
overheating and possible damage to other equipment,
do not install to control a receptacle, a motor-operated
appliance, or a transformer supplied appliance.
Backbox - # Gangs
Device Configuration
Wallplate Part #
Backbox - # Gangs
Device Configuration
Wallplate Part #
Backbox - # Gangs
Number & Type of WIDE
0
1
2
3
4
4+1**
6+1** or 8
8+1** or 10
13
15
N+N+N+N
W+N+N+N+N
W+N+N+N+N+W
W+W+N+N+N+N+W
W+W+N+N+N+N+W+W
AWP0F-40x
AWP0F-41x
AWP0F-42x
AWP0F-43x
AWP0F-44x
N*+*N*+*N*+*N
W+N*+*N*+*N*+*N
W+N*+*N*+*N*+*N+W
W*+*W+N*+*N*+*N*+*N+W
W*+*W+N*+*N*+*N*+*N+W*+*W
AWP00-40x
AWP00-41x
AWP00-42x
AWP00-43x
AWP00-44x
7**
9**
11** or 12
14
4
6
8
10
12
17
Device Configuration
N+N+N+N+N
W+N+N+N+N+N
W+N+N+N+N+N+W
W+W+N+N+N+N+N+W
W+W+N+N+N+N+N+W+W
Wallplate Part #
AWP0F-50x
AWP0F-51x
AWP0F-52x
AWP0F-53x
AWP0F-54x
5
7
9
11
Backbox - # Gangs
Device Configuration
Wallplate Part #
Backbox - # Gangs
Device Configuration
Wallplate Part #
Backbox - # Gangs
13
W+N*+*N*+*N*+*N+*N+W
W*+*W+N*+*N*+*N*+*N+*N+W
W*+*W+N*+*N*+*N*+*N+*N+W*+*W
AWP00-51x
AWP00-52x
AWP00-53x
AWP00-54x
9+1** or 11
11+1** or 13
16
N*+*N*+*N*+*N*+*N
W+N*+*N*+*N*+*N*+*N
AWP00-50x
7+1**
18
N+N+N+N+N+N
W+N+N+N+N+N+N
W+N+N+N+N+N+N+W
W+W+N+N+N+N+N+N+W
W+W+N+N+N+N+N+N+W+W
AWP0F-60x
AWP0F-61x
AWP0F-62x
AWP0F-63x
AWP0F-64x
6
8
10
12
14
Device Configuration N*+*N*+*N*+*N*+*N*+*N W+N*+*N*+*N*+*N*+*N*+*N W+N*+*N*+*N*+*N*+*N*+*N+W W*+*W+N*+*N*+*N*+*N*+*N*+*N+W W*+*W+N*+*N*+*N*+*N*+*N*+*N+W*+*W
Wallplate Part #
AWP00-60x
AWP00-61x
AWP00-62x
AWP00-63x
AWP00-64x
1.W* = right fin break-off on wide dimmer, N* = right fin break-off on narrow dimmer. *W = left fin break-off on wide dimmer, *N = left fin break-off on narrow dimmer. *W* = fin break-off on both
sides of wide dimmer, *N* = fin break-off on both sides of narrow dimmer.
2. '** Indicates that use of jumper bars is required. Jumper bars can be found in the kit with the faceplate.
3. '+1 indicates that in addition to the multi-device box, a second 1 device box shall be installed 3/4" apart from the first. A 3/4" chase nipple shall be used between the two boxes (ref. Figure 4).
4. Replace 'x' in the wall plate part number with the desired color: W=White, I=Ivory, A=Almond, T=Light Almond, E=Black, G=Gray, K=24K Gold, L=Satin Stainless, R=Antique Bronze, B=Brushed Brass.
NOTE: Metal finishes are not available on custom face plates.
AWP00-33x
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option, if within such five year period the product is returned prepaid, with
proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, New York 11747. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened,
abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for
a particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
© 2009 Leviton Mfg. Co., Inc.
For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) www.leviton.com
PK-93824-10-00-2A-X2