installation Guide
GVM 4713
SEL F SUPPORTING
stand FOR
2013+ ford Utility
interceptor
Strong
|
Reliable
|
Secure
pro-gard.com
800.480.6680
4
3
2
REVISION HISTORY
DESCRIPTION
NEW RELEASE
Widen Rear Support Bracket and Brace
1
THESE COMPONENTS ARE REQUIRED TO INSTALL
THE PRO-GARD G7047 SELF SUPPORTING STAND AND TRI-LOCK GUN RACK
3G7047-01
ITEM
D
PART NUMBER
QTY
DESCRIPTION
1
1
3G7047-01
SELF SUPPORTING BASE
2
1
3G7047-02
SUPPORT LEG -DRIVER
3
1
3G7047-03
SUPPORT LEG PASSENGER
5
1
3G7047-05
REAR SUPPORT BRACE
6
1
3G7047-04
REAR SUPPORT BRACKET
REV
SHEET
A
8,9,10
DATE
10/21/2014
12/9/2014
AUTHOR APPROVED
DBELL
DBELL
D
C
C
Tri-Lock Gun Rack
GVPMXXXX
B
B
G7047 Self Supporting Stand
UNLESS OTHERWISE SPECIFIED :
DIMENSIONS ARE IN INCHES
TOL ON 3 PLACE DECIMALS:  .005
TOL ON 2 PLACE DECIMAL  .015
DIMENSIONS ARE IN INCHESTOL ON ANGLES  1°
I.
DATE:
DRAWN BY:
CHECKED BY:
APPROVED:
ENGR 1:
10/21/2014
Duane M. Bell
Pro-gard
Products, LLC
7988 Centerpoint Dr., Suite 400
Indianapolis, IN 46256
(317) 579-6680
PART DESCRIPTION:
Refer to the diagram on the last page of these instructions to verify all parts were received.
NOTE: MUST BE CLEAN AND FREE OF BURRS
A
The information contained herein is
proprietary and the property of Pro-gard
Products and may not be reproduced,
disclosed or used for any other purpose other
than a quotation to or an order from
Pro-Gard Products without the specific
written authorization of Pro-gard Products.
4
FINISH:
STAMP:
BLACK POWDER COAT
3G7047-01
MATERIAL:
ENGR 2:
ENGR 3:
PRODUCTION:
FINAL:
Third
Angle
Projection
STEEL
SELF SUPPORTING GUN RACK
SIZE:
A
SCALE:
DRAWING NO:
ASSEMBLY NO:
1/4
APPL:
3G7047
2013+ FORD U.I.
SHEET:
REV:
A
1 OF 10
Computer Path:
3
2
1
II.
The following tools will be required to complete the installation.
A. 7/16” Socket & Ratchet
B. 5/32” Allen Wrench
E. 13mm Socket
F. 15mm Socket
C. 9/32” Allen Wrench G. 3/8” Socket
D. 5/16” Drill bit
III.
Installing the self supporting stand.
A. Remove the rear lower seat cushion from the back seat. Once the cushion is out of the way,
proceed to removing the two 15mm inner nuts that were underneath the cushion. Next, loosen
both inner rear seat bolts of the driver and passenger seat so that the seats can be lifted about
1/2”. Then install the mounting base (3G7047-01) by pushing the front seats forward. Slide the
arms of the mounting base under the seat frame and slide the back portion of the stand over the
studs located underneath the seat cushion. Once the mounting base is in place, then tighten the
two seat bolts (See FIG 1) followed by tightening the two 15mm nuts at the rear. Reinstall the
rear lower seat cushion.
IV.
Base Installation Complete
(Continue with The Gun Rack Installation)
Gun Rack
Base
FIG. 1
Passenger Inner Seat Rail
And Bolt Locations
pro-gard.com
800.480.6680
2
Driver Inner Seat Bolt
Location
4
3
2
V. Installing the Tri-Lock gun rack (Requires Pro-gard self-supporting mounting base)
3
2
1
D intended guns into the gun rack and make adjustments to fit. This will allow more access than
A. Place the
when the rack is in the vehicle, but the rack can be adjusted after installed inside the vehicle as well.
D
B. The brackets mounting the gun lock are designed to be loosened and adjusted in many directions to
accomodate most guns. Fit each gun by loosening the bolts on the gun lock bracketry so the mounting
bracket moves freely. Place your gun into the lock and in the desired position. Take a allen wrench to
tighten locks in place. (See Fig. 2)
Locks move up and down Completed Gun Fitment
C
Tilts clockwise
or counter clockwise
The shot gun
shown in the
lower position
with insert
C
Left and right
Gun locks should open
and close easily and guns
should pull in and out of
the rack with no issues
when properly installed
B
B
Fig. 2
C. Shot Gun Mounting - The shot gun can be mounted in two ways, by barrel mount or by installation of
the shot gun mount insert. To install the shot gun insert, remove the standard insert by opening the
lock and unscrewing the two insert bolts with an allen wrench. Remove the retaining ring from the bolt’s
back side. Replace with shot gun insert (3G724) and reinstall insert bolts and retaining rings on the
back side of the insert. Use the two fastener bolt’s adjustment to fit the shot gun used in the lock. (See
Fig. 3) A
Step 1
Remove barrel bracket
Step 2
Remove standard insert
4
3
3
Barrel
mounting bracket
pro-gard.com
800.480.6680
2
Fig. 3
Step 3
Replace with shot gun insert
Standard insert
3
2
1
Shot gun
insert
A
Retaining ring
VI. Self-Supporting Installation
A. For self-supporting installations, remove the four bolts
that secure the butt plates to the base of the gun rack.
Then rest the gun rack to the self supporting stand,
loosely attach the gun rack and adjust it and the butt
plates as necessary from front to back. (See Fig. 4)
NOTE:
For Optimal Conditions secure the back
of the gun rack tigth against the seat.
3
2
1
Adjustable
hole
D
locations to
provide the best
mounting
preference.
VII. Lock Box
A. Open the lock box and loosen the bolts with
a 7/16” socket and extension wrench to adjust
the box up or down as needed. (Swivel attachment
is required) Install supplied black felt over bolts
when box position has been fixed. (See Fig. 5)
C
Lock box
adjustment
bolts
B
Fig. 4
Fig. 5
A
pro-gard.com
800.480.6680
4
3
2
1
VIII. Gun lock switch and timer installation.
A. We suggest mounting the momentary release button in a concealed location that can be easily reached
by the officer, but would be hidden in case an unathorized entry occurs.
B. Connect the gun lock wiring as shown in the diagram below.
NOTE: warranty will be voided!
Pro-gard requires the use of a 10 AMP fuse between the power source and gun lock circuit or the
Fig. 6
IX. Lock Head Operating Instructions
A. To release, grasp the weapon, but do not pull it against the lid of the gun lock.
B. While depressing and holding the release button (momentary switch), push and then
pull the weapon towards the lid of the gun lock to release it from the lock.
NOTE:
One handed operation is possible utilizing the optional 8 second timer. The timer will unlock the
lock for 8 seconds following activation of the momentary switch. If the gun is not pulled out of
the lock within 8 seconds after activation of the momentary switch, the lock will automatically
re-lock.
If lid of the lock does not release, press in on the lid to release tension and reactivate the release
tip: button
(unless timer is still active).
Installation Complete!
Call Pro-gard technical support if assistance is needed. 1-800-480-6680
pro-gard.com
800.480.6680
5
MBER
Self-Supporting Mounting Base
3
G7047-01
2
REV
SHEET
A
8,9,10
1
REVISION HISTORY
DESCRIPTION
NEW RELEASE
Widen Rear Support Bracket and Brace
DATE
10/21/2014
12/9/2014
AUTHOR APPROVED
DBELL
DBELL
D
DESCRIPTION
SELF SUPPORTING BASE
SUPPORT LEG -DRIVER
SUPPORT LEG PASSENGER
REAR SUPPORT BRACE
1
REAR SUPPORT BRACKET
4
C
5
3
2
B
S OTHERWISE SPECIFIED :
ENSIONS ARE IN INCHES
N 3 PLACE DECIMALS:  .005
ON 2 PLACE DECIMAL  .015
ARE IN INCHESTOL ON ANGLES  1°
BE CLEAN AND FREE OF BURRS
LACK POWDER COAT
047-01
DATE:
DRAWN BY:
CHECKED BY:
APPROVED:
ENGR 1:
ENGR 2:
ENGR 3:
PRODUCTION:
FINAL:
Third
Angle
Projection
STEEL
10/21/2014
Duane M. Bell
Pro-gard
Products, LLC
7988 Centerpoint Dr., Suite 400
Indianapolis, IN 46256
(317) 579-6680
PART DESCRIPTION:
SELF SUPPORTING GUN RACK
SIZE:
A
SCALE:
ASSEMBLY NO:
1/4
APPL:
DRAWING NO:
3G7047
2013+ FORD U.I.
SHEET:
REV:
A
1 OF 10
Computer Path:
3
2
1
6
pro-gard.com
800.480.6680
Tri-Lock Gun Rack
4
3
2
1
PARTS LIST
ITEM
QTY
1
1
D
4
7
15
D
3GVM001-04
1.5" X 1.5" X 38" LG. ALUM EXTRUSION
**G4962-002
BUTT PLATE - BLACK NYLON
4
*2
**G4963-002
RUBBER BUTT PLATE PAD
5
*1
3GVM201-02
LOCK MOUNTING BRACKET - PASSENGER
6
*1
3GVM201-03
LOCK MOUNTING BRACKET - DRIVER
7
3*2
**G4904-NPG
R GUN LOCK
*2
**3G135
R LOCK BARREL MOUNT BRACKET
25
3G7030
UPPER PARTITION MOUNTING BRACKET
3G7031
LOWER PARTITION MOUNT BRACKET (NOT SHOWN)
11
*1
3G724
ITEM
LOCK INSERT FOR SHOT
GUN
12
*1
4GLB02
GUN SAFE
ITEM
QTY
9
24
14
28
6
26
27
22
8
13
8
15
B
14
15
2
13
14
5
C
20
10
14
21
7
14
1
26
3GVM001-04
G4962-002
2
G4963-002
4
3X149
13
3X12
1/4 FLAT WASHER, BLACK
4
15
7
3X258
1/4-20 X 0.5 BSHCS
16
18
3X259
1/4-20 SLOT NUT (NOT SHOWN)
17
6
3X33
6
1/4 FLAT WASHER, BLACK
18
6
3X122
1/4-20 x 1" HHMS, Zn
19
7
3X184
1/4-20x0.75, SBHCS, BLACK OXIDE
5
7
1
3GVM201-02
3GVM201-03
2
G4904-NPG
8
2
3G135
9
1
3G7030
20
1
3X61
1/4-20 X 3/4 CARRIAGE BOLT
1
3X16Z
1/4-20 WHIZ NUT
22
1
01501-PLAIN
EXTRUSION END CAP 10
1
3G7031
23
*4
3X16
1/4-20 WHIZ NUT (NOT SHOWN)
24
1
3X235
11
5/16-18 X 0.313 LG. BSHCS, BK
1
3G724
25
1
3X233
6-32 SLOT NUT
12
1
4GLB02
26
1
NB020-TH
NEODYMIUN MAGENT
27
1
3X232
6-32 X 5/8 FHSCS
ITEM
QTY
13
4
B
PART NUMBER
28
2
3X231
1/4-20 X 0.5 HEX CAP SCREW
29
1
3X229
0.125 RIVET (NOT SHOWN)
30
1
3G5078R
13 (NOT3X12
BLACK FELT 17 3/4" X14
31" QTY CONSUMED
SHOWNT)
LOCK BOX FELT (NOT 15
SHOWN)
31
1
3G5078R-01
32
1
3G5100
33
1
G1002
16
TIMER DELAY MODULE
28
4
6
13
8
3
2
15
14
14
15
20
10
14
21
3X149
7
MOMENTARY SWITCH
* - QTY MAY VARY DEPENDING ON CONFIGURATION
** - ITEM MAY VARY DEPENDING ON CONFIGURATION
18
9
C
1
21
27
B
1
2
DESCRIPTION
14
3
4
PART NUMBER
3GVM201-01
2
17
18
1
13
17
A
PART NUMBER
QTY
1
3
5/16-18 X 3/4 BSHCS, BK
19
25
2
1
HARDWARE LIST
13
D
1
C
12
1
*2
9
2
14
5
7
2
10
22
8
DESCRIPTION
RACK BASE WELDMENT
3
8
24
PART NUMBER
3GVM201-01
3X258
18
3X259
6
3X33
6
3X122
19
7
3X184
20
1
3X61
21
1
3X16Z
22
1
01501-PLAIN
23
4
3X16
24
1
25
1
26
1
NB020-TH
27
1
3X232
28
2
3X231
29
1
3X229
1
A
3X235
3X233
30
1
3G5078R
31
1
3G5078R-01
7
19
18
17
4
A
12
3
1
4
7
3
pro-gard.com
800.480.6680
2