Arlink 8000 Accessories
Instructions for Assembly
Round/Straight Back Worksurface
Rear Corner Support Leg
Micro Slot Accessories
Air Beam & Data Beam
Variable Angle Shelves
Foot Rest
Vertical Power Beam
Light Fixture & Tool Trolley Track
Panels
CPU Holder
Pelican Drawer/Tote Box
Swing Arm Accessories
Mobile Carts
Parts Bin Cart
Making Workspace Work® is a trademark of Lista International Corporation.
Creation Date
Jun/19/13
Document Number
AS80028
Rev
E
Description
Arlink 8000 Accessories
This manual is proprietary information of Lista International Corporation. Unauthorized
reproduction of any portion of the manual is prohibited without consent of Lista
International Corporation. The material in this manual is for informational purposes
only. It is subject to change without notice. Lista International Corporation assumes
no responsibility for any typographical errors contained in the manual.
© 2013 by Lista International Corporation, all rights reserved.
106 Lowland Street
Holliston, MA 01746-2094
E-mail: sales@listaintl.com
All rights reserved.
For questions or technical support, call 1-800-722-3020
ISO 9001 Certified
Table of Contents
Round/Straight Back
Worksurface ......................... 3
CPU Holder .......................... 16
Pelican Drawer/Tote Box ...... 17
Rear Corner Support Leg ..... 4
Swivel Keyboard Holder ....... 18
Micro Slot Accessories ......... 5
Pullout Keyboard Holder ....... 19
Heavy Duty Parts Bin Rail .... 6
Universal Brackets ................ 20
Air Beam .............................. 7
Double Articulating Arm ........ 21
Data Beam ........................... 8
Variable Angle Shelf ............. 9
Monitor Shelf with Keyboard
Holder and Mouse Tray ........ 22
Free Standing Footrest......... 10 Accessory Shelf .................... 23
Vertical Power Beam ............ 11 Document Holders ................ 24
Light Fixture: 4 Bulb ............. 12 Parts Bin Rack
for Swing Arm ....................... 25
Tool Trolley Track ................. 13
Mobile Carts ......................... 26
Peg Board &
Louvered Panel .................... 14 Parts Bin Cart ....................... 27
Marker/Tack Panel ............... 15
2
Round Corner or Straight Back Worksurface
These worksurfaces are mounted between two 90o adjacent modules. They require
one pair of worksurface support brackets. The worksurface must be fully supported
face down on a smooth surface. To prevent damage power tools should not be used.
Place the worksurface brackets in their proper locations as shown above. Install the
four 1/4”-20 x 1” machine screws provided and tighten once all are in place.
3
Rear Corner Support Leg
The rear corner support leg is used with square back corner tops that are not
supported by a rear column assembly.
The worksurface is mounted between two 90o adjacent modules. It requires one pair of
worksurface support brackets. The worksurface must be fully supported face down on
a smooth surface. To prevent damage power tools should not be used. Place the
worksurface brackets in their proper locations. Install the four 1/4”-20 x 1” machine
screws provided and tighten once all are in place.
With the worksurface mounted adjust the height of the leg relative to the worksurface
by unfastening the screw at the bottom of the leg assembly and sliding the inner tube
up or down as required. Line up the threaded insert and fasten. Fine adjustments can
be done with the leveling glide. Now slide the rear leg to the back corner of the
worksurface approximately 2” from either side and fasten to the worksurface using the
wood screws provided.
4
Parts Bin Rail Accessories
Parts Bin Rail
Modesty Panel
Micro Slot Accessories
“Micro Slot” refers to the rectangular slots punched at 1” increments along the height of
the column. There are several accessories which mount in the micro slots such as
modesty panels, parts bin rails, accessory cabinets, tool boxes, utility bins and sloping
document shelves to name a few.
To mount these accessories you insert the micro slot bracket into the slots of the
columns and push down to ensure the bracket hooks are engaged.
Parts Bin Rail Accessories, Tool Holder, Bottle Holder, Wipes Holder, and Solder
Spool Holder. These hang anywhere along the length of the parts bin rail or utility bin.
5
Heavy Duty Parts Bin Rail
Installation at 90o
1) Insert the top hooks into the inner micro slots of the columns.
2) Rotate the parts bin rail down until you engage the bottom hooks.
3) Press down firmly to fully engage the hooks.
Installation at 15o
1) Push up on the rail to disengage the hooks and pull the top of the rail forward until
the up hook catches in the column and you can not pull any farther forward.
2) Press down on the rail to fully engage the hooks.
6
Air Beam
Air beams are provided with two or three receptacles (depending on the overall length
of the beam) for 1/4” NPT quick connects. Any receptacles not used with quick
connects must be plugged. Each end of the air beam is equipped with a quick connect
fitting for 1/4” tube. This allows air beams to be connected in line. You can remove
the red blanking plug as shown above, by pushing the collar in while at the same time
pulling the plug out. Either tubing or blanking plug must be in place to prevent
pressure loss. 18” of 1/4” tube supplied.
To mount the Air Beam you insert the micro slot bracket into the slots of the columns
and push down to ensure the bracket hooks are engaged.
7
Data Beam
Data beams are provided with four duplex style outlets. The eight ports accept
modular snap in/snap out jacks or connectors for data, video or audio connectivity.
The beams are supplied with the outlets, but the jacks/connectors must be purchased
separately. On site wiring of ports in the responsibility of the customer.
To mount the Data Beam you insert the micro slot bracket into the slots of the columns
and push down to ensure the bracket hooks are engaged.
8
Variable Angle Shelf
These shelves can mount in three different orientations relative to the columns.
1) Front Mount. To mount the shelf in front of the columns you must mount the
brackets to the shelf in their rear most position.
2) Center Mount. To Mount the shelf in the center of the columns you must
mount the brackets in their central position.
3) Rear Mount. To mount the shelf in its rear most position you must mount the
brackets in their front most position.
To mount the brackets use the 5/16”-18 x 5/8” button head cap screws, flat washers
and lock nuts provided. The adjustable levers provided are used to adjust the angle of
the shelf. They are also installed with washers and lock nuts.
The Variable Angle Shelves without Lips have mounting positions for the wire divider
as shown above. The dividers are installed by pushing them into both sets of
mounting holes at the desired location.
9
Freestanding Footrest
1) See Variable Angle Shelf Assembly for footrest platform assembly, page 9.
2) Insert the two plastic plugs into the top of the frame posts.
3) Insert left and right feet into the bottom of the frame assembly. Install the clevis
pins and retainers provided.
4) Mount the Variable Angle Shelf Assembly to the Frame Assembly at the desired
height and angle.
5) Press down to engage slots.
10
Vertical Power Beam
1) Mount the top front and top rear bracket into the micro slots at the desired height.
Press down on the brackets to ensure they engage the slots.
2) Loosely bolt the powerbeam through the top hole of the brackets using the 5/16”-18
x 5/8” button head cap screw and hex nut provided.
3) Mount the bottom front bracket and the bottom rear bracket into the micro slots at
the appropriate height. Push up on the brackets to engage the slots.
4) Bolt through the bottom hole of the brackets using the 5/16”-18 x 5/8” button head
cap screw and hex nut provided.
5) Ensure all hardware is secured.
11
Light Fixture: 4 Bulb
1) Using the four #10-24 x 3/4” machine screws provided mount the retro fit brackets
to the light fixture.
2) These brackets can be mounted either in the front or rear most position of the light
fixture and the slot which allows the light to be tilted can be mounted towards either
the front or the back of the light.
3) Now mount the sub assembly to the light brackets. These brackets will have an
overall dimension of either 15 5/8”, 20 5/8” or 26 5/8” depending on what you
purchased.
4) Using the four 1/4”-20 x 3/4” machine screws, washers and lock nuts provided
mount the sub assembly as shown above.
5) Ensure all hardware is secure and mount the assembly to your workstation using
the macro slots of the columns.
12
Tool Trolley Track
The tool trolley track mounts to light brackets, with or without a light. It can be
mounted in front of or behind a light. Slide tool trolley inside the track. Position the
tool trolley track in the desired location of the light mounting brackets and install the
screws and square nuts at the each end of the track. With the assembly secured
install the end caps.
13
Pegboard and Louvered Panel
1) Fasten the four support brackets to the corners of the panel using the four 5/16”-18
x 5/8 cap screws and hex nuts provided. Do not tighten the screws.
2) Insert tabs of the stiffener into the rear slots of the panel. Press down to secure in
place.
3) Insert hooks of the support brackets into the inner micro slots of the column at the
desired height.
4) Secure all hardware.
14
Marker/Tack Panel
1)
2)
3)
4)
Mount the bottom two support brackets into the inner micro slots of the columns.
Center the panel between these two bracket and mark the mounting locations.
Using the self drilling screws provided mount the brackets to the panel.
Repeat steps 1-3 for the top brackets.
15
CPU Holder
1) The CPU should be installed prior to mounting the worksurface to the columns
2) Loosely fasten the hangers to the CPU holder using the 1/4”-20 screws provided.
3) Slide the hangers into the worksurface support beams position in desired location
and secure the hardware.
16
Pelican Drawer/Tote Box
1) Drawers should be installed prior to mounting the worksurface to the columns.
2) Loosely fasten the hangers to the Pelican Drawer using the 1/4”-20 screws
provided.
3) Slide the hangers into the worksurface support beams position in desired location
and secure the hardware.
17
Swivel Keyboard Holder
1) Slide the four hangers into the worksurface support beams with the inserts facing
into the beam.
2) Loosely fasten the keyboard channel to the hangers with the 1/4”x1” screws
provided.
3) Slide the channel into the desired location on the worksurface and secure the
hardware.
4) Slide the keyboard arm into the channel.
5) Install the four #8x3/8” screws in the ends of the channel these act as stops.
6) Mount the keyboard platform to the keyboard arm with the supplied hardware.
Operating Instructions
1) To adjust the tilt of the keyboard platform loosen the lever, set the desired angle
and retighten the lever.
2) To raise the platform grasp the platform on both sides and lift to desired height.
3) To lower the platform grasp the platform on both sides, tilt the front of the platform
up, lower to desired height and release platform.
4) The platform is fully retractable on the 23” channel
5) The keyboard arm can swivel 360o
Note: The spring assisted height lock may not function correctly until the load of the
keyboard platform, the keyboard and the mouse have been applied.
18
Series 7000 or Series 8000
Series 8000 or benches without front
support beams
Pullout Keyboard Holder
1) Mount the keyboard tray to the slides using the flat head screws and nuts provided
with the tray.
2) There are two sets of hanging bracket provided. The longer set is for use with
either Series 7000 or Series 8000 workstations. The shorter set is for use with
Series 8000 or workstations have no front support beam. Mount the appropriate
set of bracket to the slides using the Philips head screws provided.
3) Mount the assembly to the worksurface in the desired location using the #10 x 3/4”
wood screws provided.
19
Universal Bracket
8423 Heavy Duty Universal Bracket
1) Position the bracket at the desired height on either the inside or outside of the
column.
2) Mount the bracket using the three 1/4”-20 x 1 3/8” hex bolts, washers and lock nuts
provided.
8406 Double Hook Micro Slot Bracket
1) At the desired height mount the double hooked bracket into the inner and outer
micro slots.
20
Double Articulating Swing Arm
1) Using the 3/8”-16 x 2 1/2” long socket head shoulder bolt 2 1/2” flat washers and
lock nut provided, secure the two halves of the swing arm as shown.
2) Install the 2” x 1” black rectangular end cap.
21
Monitor Shelf with Keyboard Holder & Mouse Tray
1) Mount the accessory pin and steel washer to the monitor shelf.
2) Mount the assembly and the plastic washer to the swing arm.
3) The swing arm then mounts to either the 8406 or 8423 universal brackets using the
pin supplied.
4) Insert the ends of the mouse tray through both sets of holes in the monitor shelf.
5) Insert the two retainer pins.
Please note: 8895 Mouse tray is ordered separately.
22
Accessory Shelf
1) Mount the accessory pin and steel washer to the accessory shelf.
2) Mount the assembly and the plastic washer to the swing arm.
3) The swing arm then mounts to either the 8406 or 8423 universal brackets using the
pin provided.
23
Document Holder
1) Mount the accessory pin and steel washer to either the 11 7/8” or 23 5/8” document
holders.
2) Mount the assembly and the plastic washer to the swing arm.
3) The swing arm then mounts to either the 8406 or 8423 universal brackets using the
pin provided.
4) The angle of the document holders can be adjusted from 0o to 90o in 15o
increments.
24
Parts Bin Rack for Swing Arm
1) Insert the four plastic caps into the parts bin rack tubes.
2) Mount the 1/2”-13 shoulder bolt, washers and lock nut through the swing arm
mounting hole as shown.
3) The swing arm then mounts to either the 8406 or 8423 universal brackets using the
pin supplied.
25
Mobile Cart Starter & Adder
Note: Leave all fasteners loose until after stabilizer panel is installed.
1) Mount the starter and adder bases together using the four 5/16”-18 x 3” hex head
screws, washers and lock nuts provided.
2) Place the “J” bolts into the columns. Then guide the “J” bolts through the holes in
the base and install the 5/16” washers, and lock nuts.
3) Mount the outriggers to the columns using the clevis pins and retainers provided.
4) Secure the front of the outrigger to the base using a 1/4”-20 x 1” screw.
5) Mount the stabilizer panel between the columns using the six 1/4”-20 x 2” “T” bolts,
washers and wing nuts.
26
Parts Bin Cart
1) Mount the stabilizer panel between the columns using the six 1/4”-20 x 2” “T” bolts,
washers and wing nuts.
2) Mount the parts bin cart handle to either side of the cart using the two 1/4”-20 x 3/4”
screws, washer and lock nuts provided.
3) Mount the casters to the feet using the 1/2”-13 hex nuts provided.
4) Insert the plastic plugs into the foot tubes.
Double sided cart shown. Single sided cart is assembled in the same manner. The
single sided handle is different but is installed in the same manner as above.
27
Document Number: AS80028
Print Date: June, 2013
This manual is proprietary information of Lista International Corporation. Unauthorized
reproduction of any portion of this manual is prohibited without written consent of Lista
International Corporation. The material in this manual is for informational purposes only. It is
subject to change without notice. Lista International Corporation assumes no responsibility for
any typographical errors contained in this manual.
©2013 by Lista International Corporation
106 Lowland Street
Holliston, MA 01746-2095
All rights reserved.
***Warning!
Failure to comply with the proper installation of
insulating grommets or gaskets may result in
hazardous electrical conditions for personnel.
The ultimate responsibility for personnel safety
lies with the end user.
Lista International Corporation
106 Lowland Street
Holliston, MA 01746 USA
Telephone: (800) 722-3020
Fax: (508) 626-0353
sales@listaintl.com
www.listaintl.com
28