TRIMLESS OPTION
RECESSED Fixtures with a Clean Finish Edge
for Plaster or Drywall
Project
Wilsons Leather
Mission Viejo, California
Specifier
Robert Tant Lighting Design
Flagstaff, Arizona
Photographer
Mark Dell’Aquilla
Long Beach, California
Lighting
240BXWW-AK-TLD, 80 watts
Any of our Plaster / Drywall fixtures may
be ordered in the Trimless configuration.
System
The TRIMLESS feature provides the best of both worlds. Minimal intrusion into the architectural space, incorporated with
our patented reflector systems for maximum performance. Design allows ceiling/wall finish to end right at the edge of the
lighted opening.
IR-20
TRIMLESS OPTION
RECESSED Fixtures with a Clean Finish Edge
for Plaster or Drywall
TYPE:
CATALOG #:
JOB:
Specifications
Drywall
Recessed fixture which does not require a trim to
finish the ceiling opening. This option is available
for all recessed plaster/drywall fixtures. A set back
flange is provided around the perimeter of the fixture to allow for 5/8˝ gypsum board construction
for -TLD models and 7/8˝ plaster for -TLP models.
The fixture allows the ceiling finish to end right at
the edge of the lighted opening for a clean construction appearance.
TGIC polyester powder coated housing is made of
22 gauge CRS. All fluorescent fixtures are supplied
standard with Luminaire Disconnect.
B
A+ 1/8˝
A
Plaster
B
A
Section
A+ 7/8˝
B
B+ 2-1/2˝
1-1/4˝ TYPICAL
B+2-1/2˝
Front View
A – Height of the recessed housing on the required Series catalog sheet.
B – Width of the recessed housing on the required Series catalog sheet.
C – Length of the recessed TRIMLESS housing. (SEE CHART)
Sample:
A
B
AK Series
#140BXWW-AK
3-1/2˝ Ht. x 8-1/2˝ W
AK Series TRIMLESS
#140BXWW-AK-TLD 3-1/2˝ Ht. x 8-1/2˝ W
Options*
The following options are available for fixtures
provided as DRYWALL TRIMLESS.
Reflector
Diffuse (Standard for most fixtures)
Specular -SP
Stepped Diffuse Silver -ST
Painted White -W
(To eliminate a clear lamp image in
Up light installations that may occur
at certain viewing angles, we
suggest you use a White or Stepped
reflector, OR standard reflector with
Frosted Mini Lens)
Lens
Clear Lexan Mini Lens -ML
Frosted Lexan Mini Lens -MLF
Louver
Diffuse Silver Parallel Blade -LV
Chart for “C” Dimension
AA, AAD, AK, DL6, DW, Maxi Series Fixtures:
MP & CW Series Fixtures:
IW Series Fixtures:
VT Series Fixtures:
All Series Fixtures less than 20˝ length
x
x
C
22-15/16˝ L
24˝ L
Length of TRIMLESS Fixture Housing
2´ nominal
3´ nominal
4´ nominal
C = 24˝
C = 36˝
C = 48˝
C = 22-1/2˝
C = 34-5/16˝ C = 46-1/8˝
C = 22-15/16˝
C = 46-15/16˝
C = 23˝
C = SAME length for Trimless
Rough-in Dimensions:
Individual Fixture
= (“C” + 1/2˝ ) x (“B” + 1/2˝ )
Continuous Row
= (Length of row, add all “C” lengths + 1/2˝ ) x (“B” + 1/2˝ )
To specify the TRIMLESS option, for any of our recessed plaster/drywall fixtures, simply add
the following to our standard catalog number:
* Options are only available if listed on the standard
catalog cut.
Drywall installations add -TLD
Gypsum Fixture add -TLD
Mounting Flange for
5/8˝ Gypsum board.
Visible Fixture
Opening
Self-Adhesive
Drywall Joint Tape.
(by others)
Drywall Joint
Compound.
(by others)
Drywall/Gypsum
board. (by others)
Detail: Shows how fixture is finished to the opening edge.
© 2008 Engineered Lighting
Products. 2003/Rev. 07/12
C+2-1/2˝
C
Plaster installations add -TLP
Plaster Fixture add -TLP
Paper Back.
(by others)
Wire Mesh
(by others)
Mounting Flange for
7/8˝ Plaster Finish.
Visible Fixture
Opening
Plaster Rough Coat
(by others)
Top “Finish” Coat of
Plaster. (by others)
Detail: Shows how fixture is finished to the opening edge.
10768 Lower Azusa Rd., El Monte, CA 91731 • TEL: 626-579-0943 • FAX: 626-579-6803
E-MAIL: contact@elplighting.com • WEB: www.elplighting.com