MONITOR WITH DVD RECEIVER
KVT-839DVD
INSTALLATION MANUAL
© B54-4557-00/00 (MV/XV)
B54-4557-00_00.indd 1
07.2.1 5:45:48 PM
Accessories
1
0
..........1
2
..........2
!
..........1
3
..........4
@
..........1
4
..........4
#
..........1
..........2
5
..........1
6
..........1
7
..........2
8
..........4
9
..........4
2 |
KVT-839DVD
B54-4557-00_00.indd 2
07.2.1 5:45:48 PM
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
2WARNING
• If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
• Do not cut out the fuse from the ignition wire (red) and the
battery wire (yellow). The power supply must be connected
to the wires via the fuse.
¤
• If the power is not turned ON (or it is ON, but will be OFF
immediately), the speaker wire may have a short-circuit
or touched the chassis of the vehicle and the protection
function may have been activated. Therefore, the speaker
wire should be checked.
• If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
• If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
• If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
• Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
• Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
• When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Mount the unit so that the mounting angle is 30° or less.
English |
B54-4557-00_00.indd 3
3
07.2.1 5:45:49 PM
Connection
Monitor/Player unit
USB connector (iPod)
USB device
(commercially available)
USB connector
Ignition key
switch
Accessory #
Car fuse box
ACC
Wiring harness
(Accessory 2)
Ignition wire (Red)
The cable (Accessory 3) is
fixed with a chassis using
harness band (Accessory
#).
Battery wire (Yellow)
Car fuse box
(Main fuse)
+
–
Do not connect.
iPod
USB device
(commercially available)
FUSE ( 5A )
Ground wire (Black) - (To car chassis)
Antenna Cord
A
Accessory 5
Battery
Connect to the vehicle's parking brake
detection switch harness
using the supplied relay connector.
Battery wire (Yellow)
FUSE ( 10A )
Parking sensor wire (Light Green)
PRK SW
A
Ground wire (Black) - (To car chassis)
For the sake of safety, be sure to connect the parking sensor.
To vehicle's reverse lamp harness
To car light control switch
To steering remote
Connect to the terminal that is grounded when either
the telephone rings or during conversation.
To connect the Kenwood navigation system,
consult your navigation manual.
Depending on what antenna you are using,
connect either to the control terminal of the motor antenna, or to the
power terminal for the booster amplifier of the film-type antenna.
When using the optional power amplifier,
connect to its power control terminal.
To "EXT.AMP.CONT." terminal of the amplifier
having the external amp control function.
Reverse sensor wire (Purple/White)
Dimmer control wire (Orange/White)
Steering remote control input (Light Blue/Yellow)
Mute wire (Brown)
Motor antenna control wire (Blue)
Power control wire (Blue/White)
External amplifier control wire (Pink/Black)
If no connections are made, do not let the cable come out from the tab.
4 |
KVT-839DVD
B54-4557-00_00.indd 4
07.2.1 5:45:49 PM
Receiver unit
Accessory #
Accessory 3
Receiver unit
The cable (Accessory 3) is
fixed with a chassis using
harness band (Accessory
#).
FM/AM antenna input
Wiring harness
(Accessory 1)
ILLUMI
FRONT L
REVERSE
White/Black
REMO.CONT
FRONT R
White
REAR L
ANT CONT
+
To front right speaker
Green/Black
Green
REAR R
P. CONT
To front left speaker
Gray/Black
Gray
MUTE
+
+
To rear left speaker
Purple/Black
Purple
+
To rear right speaker
EXT. CONT
If you connect the ignition wire (red) and the battery wire (yellow)
to the car chassis (ground), you may cause a short circuit, that in
turn may start a fire. Always connect those wires to the power
source running through the fuse box.
English |
B54-4557-00_00.indd 5
5
07.2.1 5:45:50 PM
Receiver unit
RELAY 1
RELAY 2
System Connection
To Relay Box
Accessory 4
■ Front Preout
• Audio left output (White)
• Audio right output (Red)
■ Rear Preout
• Audio left output (White)
• Audio right output (Red)
■ Subwoofer Preout
• Audio left output (White)
• Audio right output (Red)
■ Audio/Visual input 2
• Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
■ Audio/Visual input 1
• Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
■ Rear View Camera Input
• Visual input (Yellow)
■ Audio/Visual Output
• Visual output (Yellow)
• Audio left output (White)
• Audio right output (Red)
6 |
KVT-839DVD
B54-4557-00_00.indd 6
07.2.1 5:45:51 PM
Optional Accessory Connection
iPod
(commercially available)
iPod
AUDIO IN
KCA-iP300V
(Optional Accessory)
Audio Input
Resistance-free stereo type mini
plug (3.5Ф)
iPod
VIDEO IN
Audio Output
(Black)
Visual Input
Resistance-free mini plug (3.5Ф)
iPod
Visual Output
(Yellow)
Monitor/Player unit
USB terminal
USB terminal (iPod)
iPod cannot be connected.
USB terminal
Receiver unit
Accessory 3
Connection cable
(Included in the Disc changer)
Connection cable
(Included in the Navigation System)
Disc Changer etc.
(Optional Accessory)
Navigation System
(Optional Accessory)
TV Tuner
(Optional Accessory)
TV ANTENNA INPUT
TO MONITOR UNIT
Connection cable
(Included in the TV tuner)
English |
B54-4557-00_00.indd 7
7
07.2.1 5:45:52 PM
Installation for Monitor/Player Unit
Firewall or metal support
Screw (M4X8)
(commercially available)
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Self-tapping screw
(commercially available)
Metal mounting strap
(commercially available)
Accessory 6
Make sure that the unit is installed securely in place. If the unit is unstable,
it may malfunction (eg, the sound may skip).
Installation for Receiver Unit
1. Attach the installation brackets 0 to the sides of
the receiver unit using the sems bolts 8.
Installation brackets
(Accessory 0)
Sems bolts (M4 × 8 mm)
(Accessory 8)
2. Use the tapping screw 9 to secure the receiver
unit to the audio board.
8 |
Tapping screw (ø4 × 16 mm)
(Accessory 9)
KVT-839DVD
B54-4557-00_00.indd 8
07.2.1 5:45:53 PM
Removing Monitor/Player Unit
Removing the Hard Rubber Frame
(escutcheon)
1. Engage the catch pins on the removal tool 7 and
remove the two locks on the lower level.
Lower the frame and pull it forward as shown in
the figure.
Removal Tool (Accessory 7)
Removing the Unit
1. Remove the hard rubber frame by referring to the
removal procedure in the section <Removing the
Hard Rubber Frame>.
2. Remove the Hex-head screw with integral washer
(M4 × 8) on the back panel.
3. Insert the two removal tools 7 deeply into the
slots on each side, as shown.
Removal Tool
(Accessory 7)
Catch
Lock
⁄
• The frame can be removed from the top side in the same
manner.
4. Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
2. When the lower level is removed, remove the
upper two locations.
⁄
• Be careful to avoid injury from the catch pins on the
removal tool.
5. Pull the unit all the way out with your hands, being
careful not to drop it.
English |
B54-4557-00_00.indd 9
9
07.2.1 5:45:53 PM
Installing in Japanese-made Cars
Installation on Toyota, Nissan or Mitsubishi Car using Brackets at Holes shown by "●"
or
Accessory ! (M5x6mm)
or Accessory @ (M5x7mm)
Car Bracket
Accessory ! (M5x6mm)
or Accessory @ (M5x7mm)
Screws (included in
audio unit package)
Audio unit or others
Screws (included in
audio unit package)
⁄
• Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage
the unit.
10 |
KVT-839DVD
B54-4557-00_00.indd 10
07.2.1 5:45:54 PM
Installation on Toyota Car using Brackets at Holes shown by "●"
or
When using the bracket shown above, you cannot use screws at two holes of
the right and left unit sides.
1. Mount the bracket at each side.
Accessory ! (M5x6mm)
Car Bracket
Accessory ! (M5x6mm)
Screws (included in
audio unit package)
Screws (included in
audio unit package)
2. Bend each end of case to fix the bracket.
Use a flat-blade screwdriver or pliers, and bend
each case tab into the hole of installation
bracket to fix the bracket.
English |
B54-4557-00_00.indd 11
11
07.2.1 5:45:54 PM
B54-4557-00_00.indd 12
07.2.1 5:45:54 PM