LIGHTING CONTROL
DELTALIGHT
09
09
Lighting control
More atmosphere
The time where lighting control was simply switching the lights of and off is long gone. Nowadays, lighting control is creativity.
With the Niko lighting control, you can program different atmospheres for one room. The possibilities are limitless.
Technical advantages
•
universal:
- the choice of fitting or light source can be made afterwards
•
PLC filter:
- prevents the lamps from blinking during the switchover from day to night rate
•
all dimmers comply to EN60669-2-1:
- the rules of EMC and safety are being respected
- additional external filters or compensations are not required
- no interference from television sets etc. or heavy loads
•
overload protection and short-circuit protection
- if the load is too large or simply wrong, if there is a cabling error,
if a lamp is defective etc. the dimmers go in safety mode, they do not break
09-2
DIMMERS
Modular dimmer 450VA
Dimmer suitable for incandescent lamps, halogen 230V, low-voltage halogen with ferromagnetic transformers or toroidal core transformers. Operation via push
button N.O. 230Vac, up to 30 in parallel. Use with or without memory. In compliance with the European directives for EMC and safety EN60669-2-1.
• short-circuit protection through cartridge fuse
• PLC filter for interference via the mains
• 2x1,5mm² or 1x2,5mm²
• ambient temperature: 35°C
• DIN 1module H 89mm x W 17.5mm x D 60mm
• ± 94g
• 230Vac ±10%, 40 up to 60Hz
• incandescent lamps: 450W
• halogen 230V: 450W
• ferromagnetic transformer: 450VA
• toroidal core transformer: 450VA
• min. load: 40W/50VA
• overload protection with automatic rebooth function
Complete unit
05-704
Complete unit
Pack: 10
Accessories
04-226-20
Replacement fuse F3,15AH for dimmer 310-018xx, 310-026xx and
05-704
Pack: 10
09-794-31
Fuse holder for dimmer 05-704
Pack: 10
Modular dimmer 1000VA
Dimmer suitable for incandescent lamps, halogen 230V, low-voltage halogen with ferromagnetic transformers or toroidal core transformers. Operation via push button N.O. 230Vac or without voltage. Max. 30 in parallel. Use with or without memory. In compliance with the European directives for EMC and safety EN60669-2-1.
• 230Vac ±10%, 40 up to 60Hz
• incandescent lamps: 1000W
• halogen 230V: 1000W
• ferromagnetic transformer: 1000VA
• toroidal core transformer: 1000VA
• min. load: 50W/40VA
• overload protection with automatic rebooth function
• short-circuit protection through cartridge fuse
• 2 built-in spare fuses
• PLC filter for interference via the mains
• 2x1,5mm² or 1x2,5mm²
• ambient temperature: 35°C
• DIN 4 modules H 89mm x W 70mm x D 54,5mm
• ±280g
Complete unit
05-728
Complete unit
Pack: 6
Accessories
05-706-31
Fuse holder for dimmers 05-728 and 05-700
Pack: 1
02-920-20
Fuse F5AH for dimmer 05-728
Pack: 10
Universal modular dimmer 400VA
Dimmer suitable for incandescent lamps, halogen lamps 230V and all types of low-voltage halogen lamps. Automatic selection of the dimming principle. Operation
via push button N.O. 230Vac, up to 30 in parallel. Use with or without memory. In compliance with the European directives for EMC and safety EN60669-2-1.
• 230V~ ±10%, 50Hz±1Hz
• incandescent lamps: 400W
• halogen 230V: 400W
• ferromagnetic transformer: 400VA
• toroidal core transformer: 400VA
• electronic transformer: 400VA
• min. load: 40W/40VA
• humfree
• overload protection with automatic rebooth function
• electronic short-circuit protection
• PLC filter for interference via the mains
• 2x1,5mm² or 1x2,5mm²
• ambient temperature: 35°C
• DIN 1module H 89mm x W 17.5mm x D 60mm
• ± 74g
Lighting control - 09-2
DIMMERS
09-3
Complete unit
05-703
Complete unit
Pack: 10
Universal modular dimmer 750VA (3A)
Dimmer suitable for incandescent lamps, halogen lamps 230V and all types of low-voltage halogen lamps. Automatic selection of the dimming principle. Control
via push button N.O. without voltage, 0-10V control, 1-10V current control or directly on the appliance. Up to 30 push buttons N.O. in parallel. Use with or without
memory. Additional memory for saving 1 atmopshere via push button control. Indication of the operation and feedback by means of LEDs. In compliance with the
European directives for EMC and safety EN60669-2-1.
• 230Vac ±10%, 50Hz±1Hz
• incandescent lamps: 750W
• halogen 230V: 750W
• ferromagnetic transformer: 750VA
• toroidal core transformer: 750VA
• electronic transformer: 750VA
• min. load: 60W/60VA
• humfree
• overload protection with automatic rebooth function
• electronic short-circuit protection
• PLC filter for interference via the mains
• 2 x 2,5mm² or 1 x 4mm²
• ambient temperature: 35°C
• DIN 2 modules H 90mm x W 35mm x D 66mm
• ±144g
replaces 05-707
Complete unit
05-715
Complete unit
Pack: 10
Universal modular dimmer 1400VA (6A)
Dimmer suitable for incandescent lamps, halogen lamps 230V and all types of low-voltage halogen lamps. Automatic selection of the dimming principle. Control
via push button N.O. without voltage, 0-10V control, 1-10V current control or directly on the appliance. Up to 30 push buttons N.O. in parallel. Use with or without
memory. Additional memory for saving 1 atmosphere via push button control. Integrated staircase function. Setting of the min. level between 1 and 40% and the
max. light level between 60 and 100%. Indication of the operation and feedback by means of LEDs. In compliance with the European directives for EMC and safety
EN60669-2-1.
• 230Vac ±10%, 50Hz±1Hz
• overload protection with automatic rebooth function
• incandescent lamps: 1400W
• electronic short-circuit protection
• halogen 230V: 1400W
• PLC filter for interference via the mains
• ferromagnetic transformer: 1400VA
• 2 x 2,5mm² or 1 x 4mm²
• toroidal core transformer: 1400VA
• ambient temperature: 35°C
• electronic transformer: 1400VA
• DIN 6 modules H 89mm x W 105mm x D 60mm
• min. load: 100W/100VA
• ± 440g
• humfree
Complete unit
65-410
Complete unit
Pack: 1
DALI - Universal modular dimmer 1400VA (6A)
Dimmer suitable for incandescent lamps, halogen lamps 230V and all types of low-voltage halogen lamps. Automatic selection of the dimming principle. Control
via DALI (EN 60929) or directly on the appliance. Use with or without memory. Indication of the operation and feedback by means of LEDs. In compliance with the
European directives for EMC and safety EN60669-2-1.
• 230Vac ±10%, 50Hz±1Hz
• overload protection with automatic rebooth function
• incandescent lamps: 1400W
• electronic short-circuit protection
• halogen 230V: 1400W
• PLC filter for interference via the mains
• ferromagnetic transformer: 1400VA
• 2 x 2,5mm² or 1 x 4mm²
• toroidal core transformer: 1400VA
• ambient temperature: 35°C
• electronic transformer: 1400VA
• DIN 6 modules H 89mm x W 105mm x D 60mm
• min. load: 100W/100VA
• ± 440g
• humfree
Lighting control - 09-3
09-4
DIMMERS
Complete unit
65-411
Complete unit
Pack: 1
Dimmer for systems with 1-10V current control
Dimmer suitable for switching and controlling dimmable, electronic control gear (ECG) for fluorescent, compact fluorescent lighting or dimmable LED lighting.
Control via push button N.O. without voltage, 0-10V control or directly on the appliance. Up to 30 push buttons N.O. in parallel. Use with or without memory.
Additional memory for saving 1 atmosphere via push button control. For as long as the panic function is activated, the lighting is controlled to its max. Indication of
the operation and feedback by means of LEDs. In compliance with the European directives for EMC and safety EN60669-2-1.
• 230Vac ±10%, 50Hz±1Hz
• max. switching capacity: 6A
• max. dimming capacity: 50mA
• min. dimming capacity: 0mA
• combination with all ECG in compliance with EN 60929
• control range depending on connected ECG
• 2 x 1,5mm² or 1 x 2,5mm²
• DIN 4 modules H 90mm x W 71,5mm x D 66mm
• ± 238g
replaces 65-230 and 65-330
Complete unit
05-711
Complete unit
Pack: 6
Universal dimmer 2760VA (12A)
Dimmer suitable for incandescent lamps, halogen lamps 230V and all types of low-voltage halogen lamps. Control via push button N.O. without voltage, 0-10V control, 1-10V current control or directly on the appliance. Up to 30 push buttons N.O. in parallel. Use with or without memory. Setting of the min. level between 0 and
30% and the max. light level between 50 and 100%. Indication of the operation and feedback by means of LEDs. Display indication of voltage, current, temperature
and protection status. In compliance with the European directives for EMC and safety EN60669-2-1.
• 230Vac ±10%, 50Hz±1Hz
• incandescent lamps: 2760W
• halogen 230V: 2760W
• ferromagnetic transfo: 2760VA
• toroidal core transfo: 2760VA
• electronic transfo: 2760VA
• min. load: 100W/100VA
• integrated power supply for Niko slide potentiometer: 20Vdc, 160mA
• humfree
• overload protection with automatic recover function
• electronic short-circuit protection
• filter (PLC) for disturbance signals sent via the net
• connection load: 2x2,5mm² or 1x4mm²
• connection control: 2x1,5mm² or 1x2,5mm²
• ambient temperature: 35°C
• H303mm x W200mm x D100mm
• ±4500g
Complete unit
65-412
Complete unit
Pack: 1
DALI - Universal dimmer 2760VA (12A)
Dimmer suitable for incandescent lamps, halogen lamps 230V and all types of low-voltage halogen lamps. Control via DALI (EN 60929) or directly on the appliance.
Use with or without memory. Setting of the min. level between 0 and 30% and the max. light level between 50 and 100%. Indication of the operation and feedback
by means of LEDs. Display indication of voltage, current, temperature and protection status. In compliance with the European directives for EMC and safety
EN60669-2-1.
• 230Vac ±10%, 50Hz±1Hz
• incandescent lamps: 2760W
• halogen for 230V: 2760W
• ferromagnetic transfo: 2760VA
• toroidal core transfo: 2760VA
• electronic transfo: 2760VA
• min. load: 100W/100VA
• integrated power supply for Niko sliding potentiometer: 20Vdc, 160mA
• humfree
• overload protection with automatic recover function
Lighting control - 09-4
• electronic short-circuit protection
• filter (PLC) for disturbance signals sent via the net
• connection load: 2 x 2,5mm² of 1 x 4mm²
• connection control: 2 x 1,5mm² of 1 x 2,5 mm²
• ambient temperature: 35°C
• H303mm x B200mm x D100mm
• ± 4500g
DIMMERS
09-5
Complete unit
65-413
Complete unit
Pack: 1
Universal dimmer 3680VA (16A)
Dimmer suitable for incandescent lamps, halogen lamps 230V and all types of low-voltage halogen lamps. Control via push button N.O. without voltage, 0-10V control, 1-10V current control or directly on the appliance. Up to 30 push buttons N.O. in parallel. Use with or without memory. Setting of the min. level between 0 and
30% and the max. light level between 50 and 100%. Indication of the operation and feedback by means of LEDs. Display indication of voltage, current, temperature
and protection status. In compliance with the European directives for EMC and safety EN60669-2-1.
• 230Vac ±10%, 50Hz±1Hz
• incandescent lamps: 3680W
• halogen for 230V: 3680W
• ferromagnetic transfo: 3680VA
• toroidal core transfo: 3680VA
• electronic transfo: 3680VA
• min. load: 100W/100VA
• integrated power supply for Niko sliding potentiometers: 20Vdc, 160mA
• humfree
• overload protection with automatic recover function
• electronic short-circuit protection
• filter (PLC) for disturbance signals sent via the net
• connection load: 2 x 2,5mm² or 1 x 4mm²
• connection control: 2 x 1,5mm² or 1 x 2,5mm²
• ambient temperature: 35°C
• H 303mm x W 200mm x D 100mm
• ± 4500g
Complete unit
65-416
Complete unit
Pack: 1
DALI - Universal dimmer 3680VA (16A)
Dimmer suitable for incandescent lamps, halogen lamps 230V and all types of low-voltage halogen lamps. Control via DALI (EN 60929) or directly on the appliance.
Use with or without memory. Setting of the min. level between 0 and 30% and the max. light level between 50 and 100%. Indication of the operation and feedback
by means of LEDs. Display indication of voltage, current, temperature and protection status. In compliance with the European directives for EMC and safety
EN60669-2-1.
• 230Vac ±10%, 50Hz ±1Hz
• incandescent lamps: 3680W
• halogen 230V: 3680W
• ferromagnetic transfo: 3680VA
• toroidal core transfor: 3680VA
• electronic transfo: 3680VA
• min. load: 100W/100VA
• integrated power supply for Niko sliding potentiometers: 20Vdc, 160mA
• humfree
• overload protection with automatic recover function
• electronic short-circuit protection
• PLC filter for disturbance signals sent via the net
• connection load: 2 x 2,5mm² of 1 x 4mm²
• connection control: 2 x 1,5mm² of 1 x 2,5mm²
• ambient temperature: 35°C
• H 303mm x W 200mm x D 100mm
• ± 4500g
Complete unit
65-417
Complete unit
Pack: 1
Dimmer 6 x 2300W (10A), max. 10kW (40A)
Dimmer suitable for incandescent lamps, halogen lamps 230V and all types of low-voltage halogen lamps. Purely inductive loads have to be compensated. Operation
via 0-10V control or 1-10V current control, adjustable for every circuit. Electronic monitoring with automatic power supply switch off by internal contactor in case of
malfunction or overvoltage. Forced ventilation controlled by built-in thermostat. In compliance with the European directives for EMC and safety EN60669-2-1.
• 3 x 400Vac, 50Hz
• number of circuits: 6
• max. total load: 10kW
• max. load per circuit: 2300W
• min. load per circuit: 150W/150VA
• humfree
• connection capacity: 4 x 4 + 4mm² (length 100cm)
• mounting in 19” rack (2U); H 88mm x W 483mm x D 370mm
• ± 7500g
Lighting control - 09-5
09-6
DIMMERS
Complete unit
65-340
Complete unit
Pack: 1
Lighting control - 09-6
TWILIGHT SWITCHES
09-7
Twilight switch, set of module and photo cell
Modular twilight switch suitable for switching outdoor lighting. Light sensitivity adjustable between 3 and 300lux. Consists of photo cell 350-10010 for outdoor
applications (IP54) and module 350-15010.
Complete unit
350-10000
Complete unit
Pack: 1
Twilight switch with time blocking, set of module and photo cell
Modular twilight switch with time blocking ,suitable for switching outdoor lighting. Light sensitivity adjustable between 3 and 300lux. Consists of photo cell 35010012 for outdoor applications (IP54) and module 350-15011.
Complete unit
350-10001
Complete unit
Pack: 1
Twilight switch, only module
Modular twilight switch suitable for switching outdoor lighting. To be used in combination with photo cell 350-10010. Light sensitivity adjustable from 3 to 300lux.
In compliance with the European directives for EMC and safety EN60669-2-1.
• 230Vac ±10%
• max. switching capacity: 140µF
• relay contact: N.O. max. 10A
• hysteresis on light sensitivity: +10%
• incandescent lamps: 2300W
• switch off delay: ±60s
• halogen 230V: 500W
• light sensitivity: 3-300lx:
• all low-voltage halogen lamps: 500VA
• protection degree: IP20
• fluorescent lamps (not compensated): 1200VA
• operating temperature: 5 to 50°C
Complete unit
350-15010
Complete unit
Pack: 1
Twilight switch with time blocking, only module
Modular twilight switch suitable for switching outdoor lighting. To be used in combination with photo cell 350-10012. Light sensitivity adjustable from 3 to 300lux.
Lux ON/OFF separately adjustable. Lux ON > lux OFF, negative hysteresis on light sensitivity. An active time blocking switches off the light for a preset period of
time. In compliance with the European directives for EMC and safety EN60669-2-1.
• 230Vac ±10%
• relay contact: N.O. max. 10A
• incandescent lamps: 2300W
• halogen 230V: 500W
• all low-voltage halogen lamps: 500VA
• fluorescent lamps (not compensated): 1200VA
• max. switching capacity: 140µF
• switch off delay: ±60s
• setting range lux ON: 3-300lux
• setting range lux OFF: between 10% and 70% of lux ON (range 3-90lux)
• protection degree: IP20
• operating temperature: 5 to 50°C
Complete unit
350-15011
Complete unit
Pack: 1
Lighting control - 09-7
09-8
MOTION DETECTION
Motion detector 90°, 24V, range 9m
Motion detector suitable for motion detector in warehouses. To be used in combination with daylight control module 360-35010, 360-45010 or 360-45011 for
lighting control. At a max. mounting height of 8m, the total range covers a surface of 9m(L)x1m(W). For outdoor applications, use the IP54 cover cap 390-20010.
• 24Vdc ±10%
• output contact: ON/OFF; NPN transistor output
• max. consumption: <5mA
• detection range: 90°; 0.5…9m(L)x1m(W)
• protection degree: IP20
• operating temperature: -20 to 50°C
Complete unit
350-20011
Complete unit
Pack: 1
Motion detector 90°, 24V, range 0.5-15m
Motion detector suitable for motion detection at an angle of 90° and over a distance of 0.5m to 15m. To be used in combination with daylight control module 36035010, 360-45010 or 360-45011 for lighting control. For outdoor applications, use the IP54 cover cap 390-20010.
• 24Vdc ±10%
• max. consumption: <5mA
• detection range: 90°; 0.5…15m
• protection degree: IP20
• operating temperature: -20 to 50°C
• output contact: ON/OFF; NPN transistor output
Complete unit
350-20010
Complete unit
Pack: 1
Motion detector, 90°, 24V, range with light sensor 0.5-15m
Motion detector with built-in light sensor for outdoor applications. Suitable for motion detection at an angle of 90° and over a distance of 0.5m to 15m. To be used
in combination with daylight control module 360-35010 for lighting control. Use of IP54 protection cap 390-20010 obligatory.
• detection range: 90°, 0.5…15m
• protection degree: IP20
• operating temperature: -20 to 50°C
• 24Vdc ±10%
• output contact: ON/OFF; NPN transistor output
• max. power consumption: <5mA
• light sensitivity: 3-300lux
Complete unit
350-30010
Complete unit
Pack: 1
Protection cap IP54 for motion detector 90°
Can be used to protect 350-20010, 350-20011 or 350-30010 against splashing water.
Complete unit
390-20010
Complete unit
Pack: 10
Lighting control - 09-8
MOTION DETECTION
09-9
Presence detector 180°, 24V
Intelligent presence detector suitable for ceiling mounting in offices. Fast detection, up to the slightest movements, by passive infrared (PIR) and ultrasonic (US).
Presence detection behind office walls by means of US. Automatically adapts sensitivity according to the registered movements. Is provided with integrated light
sensor. To be used in combination with power supply 360-37000 or 360-47000 that switch the load or in combination with daylight control module 360-35010,
360-45010 or 360-45011 for lighting control. The detection range can be divided by means of an adjustable cover mask.
• 24Vdc ±10%
• power consumption: max. 18mA
• output contact 1: ON/OFF (NPN transistor) sensitive to light/motion
• output contact 2: ON/OFF (NPN transistor) sensitive to motion
• potentialfree contact N.O. or N.C.
• mounting height: 2.5m
• detection range small movements: 180°, 0.5…3.5m
• detection range large movements: 180°, 3.5…9m
• hysteresis on light sensitivity: +10%
• switch off delay: 8-40min
• light sensitivity: 10-1000lux
• protection degree: IP40
• operating temperature: -5 to 50°C
Complete unit
350-20110
Complete unit
Pack: 1
Presence detector 360°, 24V
Intelligent presence detector suitable for ceiling mounting in offices. Fast detection, up to the slightest movements, by passive infrared (PIR) and ultrasonic (US).
Presence detection behind office walls by means of US. Automatically adapts sensitivity according to the registered movements. Is provided with an integrated light
sensor. To be used in combination with power supply 360-37000 or 360-47000 that switch the load or in combination with daylight control module 360-35010,
360-45010 or 360-45011 for lighting control. The detection range can be divided by means of an adjustable cover mask.
• 24Vdc ±10%
• power consumption: max. 33mA
• output contact 1: ON/OFF (NPN transistor) sensitive to light/motion
• output contact 2: ON/OFF (NPN transistor) sensitive to motion
• potentialfree contact N.O. or N.C.
• mounting height: 2.5m
• detection range small movements: 360°, 0.5…3.5m
• detection range large movements: 360°, 3.5…9m
• hysteresis on light sensitivity: +10%
• switch off delay: 8-40min
• light sensitivity: 10-1000lux
• protection degree: IP40
• operating temperature: -5 to 50°C
Complete unit
350-20111
Complete unit
Pack: 1
Mounting plate for surface mounting
Mounting plate for surface mounting of presence detector 350-20110 and 350-20111.
Complete unit
390-20110
Complete unit
Pack: 1
Lighting control - 09-9
09-10
MOTION DETECTION
Lighting control with combination of light, movement and time
Energy-saving thanks to an optimum use of lighting. Modular lighting control, to be used in combination with a photo cell and motion detector(s). Automatically
switching on, regardless of the measured level of daylight and motion detection. Automatically switching off in case of sufficient daylight or after switch off delay.
Optional control via push button N.O. Suitable for indoor and outdoor applications. In compliance with the European directives for EMC and safety EN60669-2-1.
• 230Vac ±10%
• relay contact: N.O. max. 10A
• incandescent lamps: 2300W
• halogen 230V: 500W
• all low-voltage halogen lamps: 500VA
• fluorescent lamps (not compensated): 1200VA
• max. switching capacity: 140µF
• secundary voltage: 24Vdc ±10%
• light range: 3…300lux, 30…3Klux, 300…30Klux
• hysteresis on light sensitivity: +10%
• DIN 2 modules H90mm x W35mm x D55mm
• switch off delay: 0…60min
• protection degree: IP20
• operating temperature: 5 to 50°C
Complete unit
360-35010
Complete unit
Pack: 1
Lighting control - 09-10
PHOTOCELLS
09-11
Photo cell IP54 (3-300lux)
Photo cell for outdoor applications (IP54). To be used in combination with twilight switch 350-15010. The photo cell has a fixed range of 3-300lux.
• 56Vdc ±10%
• output signal: 0 -10V
• light sensitivity: 3-300lx:
• protection degree: IP54
• operating temperature: -40 to 50°C
Complete unit
350-10010
Complete unit
Pack: 10
Photo cell IP20, adjustable measuring range
Photo cell for indoor applications (IP20). To be used in combination with daylight control modules 360-35010, 360-45010, 360-45011. The photo cell has a variable
range of 3-300lux, 30-3Klux, 300-30Klux or 600-60Klux. Suitable for outdoor applications if the IP54 protection cap 390-10011 is used.
• 24Vdc ±10%
• output signal: 0 -10V
• light sensitivity: 3-300…600-60Klux
• protection degree: IP20
• operating temperature: -40 to 50°C
Complete unit
350-10011
Complete unit
Pack: 10
Photo cell IP54, adjustable measuring range
Photo cell for outdoor applications (IP54). To be used in combination with twilight switch 350-15011 and daylight control module 360-35010. The photo cell has a
variable range of 3-300lux, 30-3Klux, 300-30Klux or 600-60Klux.
• 24Vdc ±10%
• protection degree: IP54
• output signal: 0 -10V
• operating temperature: -40 to 50°C
• light sensitivity: 3-300…600-60Klux
Complete unit
350-10012
Complete unit
Pack: 10
Lighting control - 09-11
09-12
DAYLIGHT CONTROL
Daylight control ON/OFF switching
Energy-saving thanks to an optimum use of lighting. Modular daylight control for zone-based switching of indoor lighting. Use in combination with a photo cell,
motion detector(s) and power supply 360-47000 for switching loads. Automatically switching on, regardless of the measured level of daylight and motion detection.
Automatically switching off in case of sufficient daylight or after switch off delay. Optional control via time switch, push button N.O., 4-fold push button with
feedback LEDs. Provided with 4 preprogrammed applications. In compliance with the European directives for EMC and safety EN60669-2-1.
• 24Vdc ±10%
• zones: 1, 2 or 3
• light range: 3…300lux, 30…3Klux, 300…30Klux, 600…60Klux
• hysteresis: +10%...+80%
• switch off delay: 0…60min
• protection degree: IP20
• DIN 4 modules H90mm x W70mm x D55mm
• operating temperature: 5 to 50°C
Complete unit
360-45010
Complete unit
Pack: 1
Dimmable daylight control
Energy-saving thanks to an optimum use of lighting. Modular daylight control for zone-based dimming of indoor lighting. Provided with three 1-10V outputs for
controlling dimmable, electronic control gear (ECG) for fluorescent, compact fluorescent lighting. Use in combination with a photo cell, motion detector(s) and
power supply 360-47000 for switching loads. Automatic lighting control, depending on the measured level of daylight and motion detection. Automatically switching
off in case of sufficient daylight or after switch off delay. Optional control via time switch, push button N.O., 4-fold push button with feedback LEDs. Provided with 5
preprogrammed applications. In compliance with the European directives for EMC and safety EN60669-2-1.
• 24Vdc ±10%
• output 1, 2 and 3: 1-10V, max. dimming capacity 50mA
• zones: 1, 2 or 3
• light range: 3…300lux, 30…3Klux, 300…30Klux, 600…60Klux
• switch off delay: 0…60min
• protection degree: IP20
• DIN 4 modules H90mm x W70mm x D55mm
• operating temperature: 5 to 50°C
Complete unit
360-45011
Complete unit
Pack: 1
Power supply daylight control 24V/1A
Power supply for daylight control module 360-45010, 360-45011. As stand-alone power supply suitable for presence detector 350-20110, 350-20111. Provided with 3
relay contacts that switch the load. Built-in overvoltage protection. In compliance with the European directives for EMC and safety EN60669-2-1.
• 230Vac ±10%
• secundary voltage: 24Vdc ±10%, max. 1A
• relay contact 1, 2 and 3: N.O. max. 10A
• incandescent lamps: 2300W
• halogen 230V: 500W
• all low-voltage halogen lamps: 500VA
• fluorescent lamps (not compensated): 1200VA
• max. switching capacity: 140µF
• 3 NPN transistor inputs
• protection degree: IP20
• DIN 4 modules H90mm x W70mm x D55mm
• operating temperature: 5 to 50°C
Complete unit
360-47000
Complete unit
Pack: 1
Cable for connection to daylight control
Bus cable adapter suitable for the connection between daylight control module 360-45010, 360-45011 and a bus system (e.g. Nikobus).
Complete unit
390-40010
Complete unit
Pack: 10
Lighting control - 09-12
DAYLIGHT CONTROL
09-13
Cable for connection to the daylight control (RJ12)
RJ12 cable suitable for the connection of a daylight control module 360-45010, 360-45011 to power supply 360-47000.
Complete unit
390-40011
Complete unit
Pack: 10
Lighting control - 09-13
09-14
ACCESSORIES
Protection cap IP54 for photo cell
Protection cap IP54 for outdoor applications. Suitable for upgrading photo cell 350-10011 with IP20 protection degree to IP54.
Accessories
390-10011
Complete unit
Pack: 10
Vandalproof protection cap for wall mounting
Metal protection cap for motion detectors 350-20011, 350-20010 and 350-30010.
Accessories
390-20000
Complete unit
Pack: 1
Vandalproof protection cap for ceiling mounting
Metal protection cap for presence detectors 350-20110, 350-20111, 350-20053, 350-20054 and 350-20055.
Accessories
390-20001
Complete unit
Pack: 1
Power supply 24V/40mA with 10A contact
Power supply suitable for presence detector 350-20110, 350-20111. Provided with a 10A relay contact that switches the load. Built-in overvoltage protection. In
compliance with the European directives for EMC and safety EN60669-2-1.
• 230Vac ±10%
• fluorescent lamps (not compensated): 1200VA
• secundary voltage: 24Vdc ±10%, max. 40mA
• max. switching capacity: 140µF
• relay contact: N.O. max. 10A
• NPN transistor input
• incandescent lamps: 2300W
• protection degree: IP20
• halogen 230V: 500W
• DIN 2 modules H90mm x W35mm x D55mm
• all low-voltage halogen lamps: 500VA
• operating temperature: 5 to 50°C
Accessories
360-37000
Complete unit
Pack: 1
Power supply daylight control 24V/1A
Power supply 230Vac / 24Vdc, max. 1A. Built-in overvoltage protection. In compliance with the European directives for EMC and safety EN60669-2-1.
• 230Vac ±10%
• secundary voltage: 24Vdc ±10%, max. 1A
• protection degree: IP20
• DIN 4 modules H90mm x W70mm x D55mm
• operating temperature: 5 to 50°C
Accessories
360-47001
Complete unit
Pack: 1
Lighting control - 09-14
ACCESSORIES
09-15
Control module for modular dimmers
,
Extendable up to 10 command points by N.O. push buttons. A brief press on the button for switching the light on or off. A long press for dimming up or down. A
renewed press reverses the dimming direction. The min. period of time between two presses has to be min. 500 ms.
.
&!(6
6^ (Z
• control: built-in push button
• load extension: modular dimmer 05-704, 05-707 and 05-728. Do not
combine different types!
• replacement fuse: 05-700-04
• weight: 0,270kg
• dimensions: 4 modules DIN; H 89 x W 70 x D 54,5mm
Accessories
.
,
&!(6
6^ (Z
05-700
Complete unit
Pack: 1
DALI - Modular power supply
A DALI power supply always has to be connected to the bus. The max. voltage on the DALI bus amounts to 250mA. The modular power supply is provided with an
electronic over-voltage, short-circuit and over-temperature protection. Protections are indicated with a red LED. Presence of power supply is indicated with a green
LED. If the Niko power supply is connected to components of other manufacturers, SELV is no longer guaranteed. The power supply can also be used for other systems
than DALI, on the condition that they have the same specifications.
• power supply: 230V~ 50Hz Dimensions: DIN 4 modules H 89 x B 70 x D
54,5mm
• secondary voltage: 16 or 22,5V DC (adjustable)
• weight: 0,4kg
• dimensions: DIN 4 modules; H 89 x B 70 x D 54,5mm
• DALI compatibility: from 7,5 to 22,5V DC, power protection active starting
from 240mA
Accessories
67-710
Complete unit
Pack: 6
Lighting control - 09-15