M. S. RAMAIAH INSTITUTE OF TECHNOLOGY
BANGALORE-54
(Autonomous Institute, Affiliated to VTU)
SYLLABUS
Outcome Based Education Curricula
(for the Academic year 2016 – 2017)
VII &VIII Semester B. E.
Electrical and Electronics Engineering
M. S. Ramaiah Institute of Technology (MSRIT) was started in 1962 by the late Dr. M.S. Ramaiah,
our Founder Chairman who was a renowned visionary, philanthropist, and a pioneer in creating
several landmark infrastructure projects in India. Noticing the shortage of talented engineering
professionals required to build a modern India, Dr. M.S. Ramaiah envisioned MSRIT as an institute
of excellence imparting quality and affordable education. Part of Gokula Education Foundation,
MSRIT has grown over the years with significant contributions from various professionals in
different capacities, ably led by Dr. M.S. Ramaiah himself, whose personal commitment has seen the
institution through its formative years. Today, MSRIT stands tall as one of India’s finest names in
Engineering Education and has produced around 35,000 engineering professionals who occupy
responsible positions across the globe.
About the Department:
The department was started in the year 1962 along with the establishment of the college. It was
offering undergraduate program till 2003. In 2003 the Dept. was recognized as a Research Centre by
Visvesvaraya Technological University, Belgaum and started offering Ph.D. and M.Sc. (Engg.)
programs. In 2004 the Dept. started to offer PG program in Computer Applications in Industrial
Drives. UG Programme Electrical & Electronics Engineering has been granted the
accreditation status by NBA for five years with effect from July 2015.
The department has 18 well-qualified faculty members. The entire faculty holds postgraduate degree
in either Power Systems / Power Electronics. Four of the faculty are doctorates. Dr. Premila
Manohar is Ph.D in HVDC transmission (from HVE, IISc., 1991), Dr. Sanjaya Lakshiminarayan is
doctorate in Power Electronics & Drives (from CEDT, IISc., 2007), Dr. Pradipkumar Dixit is
specialized in High Voltage Engineering (Ph. D from Visvesvaraya Technological University,
Belgaum, 2009) and Dr.T.V.Snehaprapha is Ph.D in Power Electronics & Drives (from JNTU,
Hyderabad, 2015). In addition, Dr. G. R. Nagabhushana, with a long record of service (Retired
Professor from HVE, IISc., Bangalore) is with the department as Professor Emeritus.
2
Faculty
Sl.
No.
1
Name of Faculty
Dr. G. R. Nagabhushana
Qualification
Designation
B.Sc., B.E., M.E., Ph.D
Professor Emeritus
Faculty Identified for Under Graduate
2
Dr.Premila Manohar
M. E., Ph.D (IISc)
Professor & Head
3
Dr. Pradipkumar Dixit
M. Tech., Ph.D
Professor
4
Smt. K.N. Prasanna
M. E.
Associate Professor
5
Sri.C.Ravindra Kumar
M. E.
Assistant Professor
6
Sri.Victor George
A.M.I.E., M.Tech. (Ph.D)
Assistant Professor
7
Sri.Vinayaka V Rao
M. Tech., (Ph.D)
Assistant Professor
8
Smt.S.Dawnee
M. Tech., (Ph.D)
Assistant Professor
9
Sri.K.Ramakrishna Murthy
M. Tech., (Ph.D)
Assistant Professor
10
Smt. Kusumika Krori Dutta
M.Sc (Engg.).
Assistant Professor
11
Sri.Narsimpur Tushar Suresh
M. Tech.
Assistant Professor
12
Smt. Archana Diwakar
M. Tech.
Assistant Professor
13
Smt. Aruba Rajan
M. Tech.
Assistant Professor
14
Sri. Gurunayk Nayak
M.Tech.
Assistant Professor
15
Sri. Chandrashekhar Badachi
M.Tech., (Ph.D)
Assistant Professor
Faculty Identified for Post Graduate
16
Dr.T.V.Snehaprabha
M. E.,Ph.D
Associate Professor
17
Sri.Kodeeswara Kumaran
M. Tech., (Ph.D)
Assistant Professor
18
Ms. Mamatha G. M.
M.Tech.
Assistant Professor
3
Vision and Mission
The Vision of MSRIT: To evolve into an autonomous institution of international standing for
imparting quality technical education
Mission: MSRIT shall deliver global quality technical education by nurturing a conducive learning
environment for a better tomorrow through continuous improvement and customization.
Quality Policy
“We at M. S. Ramaiah Institute of Technology, Bangalore strive to deliver comprehensive,
continually enhanced, global quality technical and management education through an established
Quality Management system Complemented by the Synergistic interaction of the stake holders
concerned”.
The Vision of the Department: To excel in engineering education and research, inculcating
professional ethics in students and emerge as a leaders in the country in the field of electrical &
electronics engineering
Mission of the Department: The mission of the department is to produce graduates who are capable
of taking leadership positions. Our graduates:
 Understand the basic principles of modern electrical & electronics technology
 Are able to apply their knowledge to solve problems arising in whatever career path they
choose.
 Are sensitive to societal issues and are committed to professional ethics.
Process of deriving the vision and mission of the department
Process of deriving the vision and mission of the department is shown in Figure below
Institute’s Vision &
Mission
Management
Vision &
Mission of the
Department by
the committee
Parents
Industry
Alumni
Department
Faculty
Students
Periodic Review
4
Process of Deriving the Programme Educational Objectives (PEOs) of the programme
Department Vision
& Mission
Institute Vision &
Mission
Committee formation and preparation of questionnaire
Conduction of Survey
Student
s
Parents
Alumni
Industry
PG faculty
Collect data
(Department Committee)
Deliberate, Analyze and
summarize the data
(Board of Studies)
Academic Council&
Governing Council
Accept & Approve
PEOs
PEOs of the program
PEO 1: Produce graduates who will have the ability to apply the knowledge of basic sciences
engineering sciences and electrical engineering to excel in professional career.
PEO 2: Produce graduates who will continue to enhance their knowledge.
PEO 3: Produce graduates who are confident to take up diverse career paths.
PEO 4: Produce graduates who will provide leadership and demonstrate the importance of
professional integrity.
5
Process of deriving the Programme Outcomes (POs)
The Programme outcomes are defined taking into account the feedback received from faculty,
alumni, Industry and also from guidelines put across by regulatory/professional bodies and graduate
attributes which are in line with programme educational objectives. The following figure indicates
the information flow.
Department Vision and
Mission
Institute Vision and
Mission
Feedback
Faculty
Programme Educational
Objectives
Student
Programme Outcomes
Graduate Attributes
Regulatory bodies such
as UGC,AICTE,VTU
Alumni
Professional bodies
such as IIIE, NITIE
Industry
PO’s of the program offered
Engineering Graduates will be able to:
1. Engineering knowledge: Apply the knowledge of mathematics, science, engineering
fundamentals, and an engineering specialization to the solution of complex engineering
problems.
2. Problem analysis: Identify, formulate, review research literature, and analyze complex
engineering problems reaching substantiated conclusions using first principles of mathematics,
natural sciences, and engineering sciences.
3. Design/development of solutions: Design solutions for complex engineering problems and
design system components or processes that meet the specified needs with appropriate
consideration for the public health and safety, and the cultural, societal, and environmental
considerations.
4. Conduct investigations of complex problems: Use research-based knowledge and research
methods including design of experiments, analysis and interpretation of data, and synthesis of the
information to provide valid conclusions.
5. Modern tool usage: Create, select, and apply appropriate techniques, resources, and modern
engineering and IT tools including prediction and modeling to complex engineering activities
with an understanding of the limitations.
6. The engineer and society: Apply reasoning informed by the contextual knowledge to assess
societal, health, safety, legal and cultural issues and the consequent responsibilities relevant to
the professional engineering practice.
6
7. Environment and sustainability: Understand the impact of the professional engineering
solutions in societal and environmental contexts, and demonstrate the knowledge of, and need for
sustainable development.
8. Ethics: Apply ethical principles and commit to professional ethics and responsibilities and norms
of the engineering practice.
9. Individual and team work: Function effectively as an individual, and as a member or leader in
diverse teams, and in multidisciplinary settings.
10. Communication: Communicate effectively on complex engineering activities with the
engineering community and with society at large, such as, being able to comprehend and write
effective reports and design documentation, make effective presentations, and give and receive
clear instructions.
11. Project management and finance: Demonstrate knowledge and understanding of the
engineering and management principles and apply these to one’s own work, as a member and
leader in a team, to manage projects and in multidisciplinary environments.
12. Life-long learning: Recognize the need for, and have the preparation and ability to engage in
independent and life-long learning in the broadest context of technological change.
Programme Specific Outcomes (PSOs)
PSO1: Identify, formulate, analyze, design and implement—electrical and electronics circuits,
control systems, drives, power systems and power electronic systems.
PSO2: Use modern tools to solve problems in diverse and multidisciplinary environment.
PSO3: Understand the impact of engineering solutions in societal and environmental context,
commit to professional ethics, lifelong learning and communicate effectively.
PSO4: Apply project management techniques to electrical/electronic(s) systems, exhibiting
team Work.
Mapping of PEO’s and PO’s
The correlation between the Programme outcomes and Program Educational objectives are mapped
in the Table shown below:
Correlation between the POs and the PEOs
Sl.
No.
1
2
3
4
Programme Outcomes
Programme Educational Objectives
a
b
c
d
e
f
g
h
i
j
k
l
Produce graduates who will have the ability to
apply the knowledge of basic sciences
X X X
X
X X X
engineering sciences and electrical engineering
to excel in professional career.
Produce graduates who will continue to enhance
X X X
X
X X X X
their knowledge.
Produce graduates who are confident to take up
X
X
X
X
diverse career paths.
Produce graduates who will provide leadership
and demonstrate the importance of professional
X
X X X
X
integrity.
7
Curriculum breakdown structure:
In accordance with the program criteria set by Institute of Electrical and Electronics Engineers
(IEEE) and the Program Outcomes, the structure of the Electrical Engineering curriculum is
developed such that both breadth and depth are provided across a range of electrical engineering
topics. This is achieved by offering required basic courses and a wide variety of advanced courses in
the area of electrical engineering. The Course code, Course title, the number of contact hours and the
number of credits for each course are given in the following table. The courses are grouped in line
with the major components of the curriculum namely: (i) Mathematics and Basic sciences, (ii) Basic
Engineering courses, (iii) Humanities and Social Sciences, (iv) Professional core courses, (v)
Electives and (vi) industry exposure/internship.
Breakup of Credits for BE Degree Curriculum. (I to VIII Semester)
Sem
HSS
BS
ES
PCS
Professional
Electives
I
04
10
10
-
II
02
10
14
III
-
04
IV
-
V
Project /
Seminar/
Internship
Total
Credits
-
-
24
-
-
-
26
-
21
-
-
-
25
04
-
22
-
-
-
26
-
04
-
14
06
-
-
24
VI
-
-
-
17
09
-
-
26
VII
-
-
02
15
03
03
02
25
VIII
Total
04
-
04
--
-
16
24
10
32
30
89
18
03
18
200
HSS
Other
Electives
- 10
- Humanities and Social Sciences
BS
- Basic Sciences (Mathematics, Physics, Chemistry)
ES
- Engineering Sciences (Materials, Workshop, Drawing, Computers).
PCS - Professional Core Subjects
Prof. Ele - Professional Electives, relevant to the chosen specialization branch.
Other Ele - Elective Subjects, from other technical and / or emerging
subject Areas.
Project / Seminar- Project Work, Seminar and / or Internship in industry
or elsewhere.
8
-
32
30
89
18
-03
-18
Board of Studies for the Period 2016-2018
1. Head of the Department concerned:
Dr. Premila Manohar
2. At least five faculty members at different levels covering different specializations constituting
nominated by the Academic Council
i. Dr. Pradipkumar Dixit
ii. Mrs. S. Dawnee
iii. Mr. Kodeeswara Kumaran
iv. Mr. Victor George
v. Mrs. Archana Diwakar
3. Special invitees
i. Mr. Rohit Chakravarthy, Robert Bosch Engineering & Business Solutions Pvt LtdBangalore
ii. Mr. Ravindra. P, AMD India Pvt. Ltd., Bangalore
iii. Mr Bapiraju J, ABB, GISL, MV Drives, Bangalore
4. Two experts in the subject from outside the college
i. Dr. S. Krishna
Asst. Professor, Dept. of E&EE, IITM, Chennai.
ii. Dr. P. Parthiban,
Assistant Professor, Dept. of E&EE,
NITK, Surathkal, Mangalore.
iii. Prof. T. K. Anantha Kumar
Dept. of E&EE, Cambridge Institute of Technology, Bangalore
5. One expert from outside the college, nominated by the Vice Chancellor
Dr. R. Nagaraja, Director,
Power Research & Development Pvt. Ltd., Bangalore.
6. One representative from industry/corporate sector allied area relating to placement nominated by
the Academic Council
Mr. Veerendra Vasam, Innovation Manager, Schneider Electric Co.Pvt. Ltd., Bangalore
7. One postgraduate meritorious alumnus to be nominated by the Principal
i. Mr. Goutham Ramamurthy,
Honeywell Technology Solutions Lab Pvt. Ltd., Bangalore.
8. Student Member from final year
Mr Amrit Dash
9
M.S. RAMAIAH INSTITUTE OF TECHNOLOGY, BANGALORE – 54
(Autonomous Institute, Affiliated to VTU)
SCHEME OF TEACHING FOR THE ACADEMIC YEAR 2016-2017
VII SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING
Sl.No.
Subject
Subject
Code
Teaching
Category
Department
Credits
L
T
P
Total
1
EE701
Switchgear and Protection
Electrical & Electronics
Engineering
PS(Core)
3
0
0
3
2
EE702
Power Systems-II
Electrical & Electronics
Engineering
PS(Core)
3
1
0
4
3
EE703
Quality Management
Electrical & Electronics
Engineering
Engineering
Sciences
2
0
0
2
4
EE706
Electric Drives
Electrical & Electronics
Engineering
PS(Core)
3
1
0
4
5
EE701L
Protection & High Voltage Lab.
Electrical & Electronics
Engineering
PS(Core)
0
0
2
2
6
EE702L
Power Systems Lab.
Electrical & Electronics
Engineering
PS(Core)
0
0
2
2
7
EE705
Project Phase - I
Electrical & Electronics
Engineering
PS(Core)
0
0
2
2
11
2
6
19*
Total
10
SWITCHGEAR AND PROTECTION
Subject Code: EE701
Credit: 3: 0: 0
Subject Name: Switchgear and Protection
Contact Hours: 42
Prerequisites: Nil
Course Coordinator/s: Sri. C. Ravindra Kumar/Dr.Pradipkumar Dixit
Course Objectives




Introduce students’ to power system protection and switchgear
Teach students the protection systems used for electric machine, transformers, Bus-bars
and overhead lines
Teach students the theory, construction, and applications of main types of circuit breakers
Enhance students’ knowledge in over current, differential and distance protection
Course contents:
Unit I
Switches And Fuses: Isolating switch, Fuse law, cut-off characteristics, time current
characteristics, fuse material, HRC fuse, liquid fuse, application of fuse.
Principles of Circuit Breakers: Principles of AC circuit breaking, principles of DC circuit
breaking, Initiation of arc, maintenance of arc, arc interruption, arc interruption theoriesslepian’s theory and energy balance theory, Re-striking voltage, recovery voltage, rate of rise of
Re-striking voltage, current chopping, rating of circuit breakers.
Unit II
Circuit Breakers: Air circuit breakers-Air break and Air blast circuit breakers, Oil circuit
breakers-single break, double break, minimum OCB SF6 breaker-preparation of SF6 gas, puffer
and non-puffer type of SF6 breakers.
Vacuum Circuit Breakers: Construction, principle of operation, advantages and disadvantages
of different types of circuit breakers.
Unit III
Philosophy of protective relaying system, Zones of Protection, Primary and Back up Protection,
essential qualities of Protective Relaying, Classification and Components of Protection System.
Conventional and Static relays - advantages and limitations, amplitude and phase comparators,
level detectors, logic circuits, static over current, directional, distance relays.
Unit IV
Relay characteristics: Non-directional and Directional Overcurrent relays, IDMT and directional
characteristics, Differential relay –principle of operation, percentage differential relay, bias
characteristics, impedance relay, reactance, Mho relay and Buchholz relay
11
Unit V
Types of faults and their effects. Generator protection scheme (stator, rotor, reverse power
protection, backup etc.).Power transformer protection (external and internal faults protection),
bus bar and Motor protection. Transmission line protection (current/time grading, distance,
carrier aided protection), Introduction to Numerical Relays, Numerical over current and distance
protection
Text Books:
1. Sunil S.Rao, ‘Switchgear and Protection’,Khanna Publishers.
2. Badriram and Viswa Kharma, ‘Power System Protection and Switchgear’, TMH.
3. Y.G.Painthankar and S R Bhide, ‘Fundamentals of Power system Protection’, PHI, 2007.
Reference Books:
1. Soni, Gupta and Bhatnagar, ‘A Course in Electrical Power’, Dhanapat Rai Publications.
2. Ravindaranath and Chandra, ‘Power System Protection and Switchgear’, New Age
Publications.
3. Dr.S.L.Uppal, ‘Electrical Power’, Khanna Publishers.
Course Outcomes
A student completing this course should be able to:
1. Select a fuse and/or a circuit breaker for a given application.(PO-1)
2. Distinguish between various types of circuit breakers (PO-1)
3. Compare the characteristic of different relays (PO-1)
4. Identify a proper relay for different zones of protection (PO-1,6)
5. Ability to identify different faults in generator, power transformers, transmission lines,
busbars and motors and their protection. (PO-1,6)
12
POWER SYSTEMS – II
Subject Code: EE702
Credits: 3: 1: 0
Prerequisites: Nil
Contact Hours: 70
Course Coordinator/s: Dr.Pradipkumar Dixit & Chandrashekhar Badachi
Course Objectives





Formulate the YBus and Z Bus
Obtain load flow solution by Gauss Siedel method, Newton Raphson Method and FDFL
method
Obtain economic load dispatch of a thermal power plant
Apply numerical techniques to solve the swing equation and determine the transient
stability.
Develop the block diagram of ALFC and evaluate load sharing. Understand Compensation
techniques
Course contents:
Unit I
Modeling of transmission lines, off nominal transformer, loads and generator. Formation of YBUS
by method of inspection. Basic concepts of network topology. Formation of YBUS by method of
singular transformation..
ZBUS formation by inverting YBUS and ZBUS building Algorithm (Without mutual coupling).
Computation of 3phase fault current using ZBUS (derivation excluded).
Unit II
Load Flow Studies: Introduction, review of numerical solutions of algebraic equations by
iterative methods, power flow equations, and classification of buses, operating constraints and
data for load flow study. Load flow solution using Gauss–Seidal method, (numerical problem
for not more than 2 iteration), acceleration of convergence. Load flow solution using Newton–
Raphson method in polar co-ordinates (numerical problem for 1 iteration only). Fast Decoupled
load flow method.
Unit III
Economic Operation of Power System: Introduction, economic generation scheduling
neglecting losses and, iterative techniques. Derivation of transmission loss formula. Economic
dispatch including transmission losses. Approximate penalty factor. Iterative technique for
solution of economic dispatch with losses. Introduction to unit commitment (problem
formulation)
13
Unit IV
Transient Stability Studies: Classical and transient representation of Machine. Numerical
solution of swing equation by Point-by-Point method, Modified Euler’s method, Runge–Kutta
method, Milne’s predictor – corrector method. Solution techniques with flowcharts/algorithms.
Unit V
Load Frequency Control: Schematic diagram of automatic load frequency control and
automatic voltage control. Generator model, turbine model, and governor model. Block diagram
representation of single area ALFC.
Compensation in Power Systems: Introduction, load compensation, line compensation, series
compensation and shunt compensators. Principle and operation of converters. Introduction to
FACTS Controllers.
Text books:
1. Nagrath, I. J., and Kothari, D. P. ,’Modern Power System Analysis’, TMH, 2003.
2. K.UmaRao, ‘Computer Techniques and Models in Power Systems’, I.K. International,
2007.
3. Pai, M.A, ‘Computer Techniques in Power System Analysis’, TMH, 2nd Edition.
4. John Grainger, Jr.,William Stevenson, ‘Power System Analysis’, McGraw Hill, 1994.
5. Stag, G. W., and El Abiad, A. H. ‘Computer Methods in Power System Analysis’, McGraw
Hill International Student Edition, 1968.
Reference books:
1. Singh, L. P., ‘Advanced Power System Analysis and Dynamics’, New Age International
(P) Ltd, New Delhi, 2001.
2. HaadiSadat,’Power System Analysis’, TMH, 2nd Edition, 12th Reprint.
3. Rudrapratap, ‘MATLAB: Getting started with MATLAB’, Oxford University Press, 2005.
Course Outcomes
After the completion the course, the students will be able to:
1. Formulate the YBUS and Z Bus (PO-1)
2. Obtain load flow solution by Gauss Siedel method, Newton Raphson Method and FDLF
Method (PO-1)
3. Obtain economic load dispatch of a thermal power plant (PO-1)
4. Apply numerical techniques to solve the swing equation and determine the transient
stability. (PO-1)
5. Develop the block diagram of ALFC, evaluate load sharing. (PO-1)
14
QUALITY MANAGEMENT
Subject Code: EE703
Credit: 2: 0: 0
Prerequisites: Nil
Contact Hours: 28
Course Coordinator/s: Sri. Tushar Narsimpur Suresh/ Sri .C.Ravindra Kumar
Course Objectives:





Demonstrate an understanding of the importance of quality and the prevailing quality
philosophy in use today.
Demonstrate an understanding of the importance of “statistical thinking” in industry.
An ability to introduce concepts of common and special cause random variation.
Demonstrate an understanding of the usefulness and theory behind the use of Shewhart
control charts.
An ability to apply sampling techniques for assessing product quality.
Course contents
UNIT -I
Introduction: Definition of quality, quality function, dimensions of quality, quality engineering
terminology, The Juran’s spiral of quality, quality costs – four categories of costs and hidden
costs, Brief discussion on sporadic and chronic quality problems
Quality Assurance: Definition and concept of quality assurance, quality audit concept, audit
approach, ingredients of a quality program.
UNIT -II
Statistical Process Control: Introduction to statistical process control, seven QC tools, process
capability – Basic definition, standardized formula, chance and assignable causes of variation.
Basic principles of control charts and analysis of pattern of control charts.
Control Charts for Variables: Controls charts for X bar and Range, statistical basis of the
charts development and use of X bar and R charts, interpretation of charts.
UNIT -III
Control Charts for Attributes: Control charts for fraction non-conforming(defectives)
development and operation of control chart, brief discussion on variable sample size.
Control Charts for non-conformities (defects)-development and operation of control chart for
constant sample size and variable sample size.
UNIT -IV
Sampling Inspection: Concept of acceptance sampling, acceptance plans-single and double
plans, Operating characteristics curves-construction and use. Producer risk and consumer risk.
Determination of AOQ, LTPD, ASN, AOQL, ATI
15
UNIT -V
Reliability and Life Testing: Failure models of components, definition of reliability, MTBF,
Failure rate, failure rate curve, types of failure, reliability evaluation in simple cases of
exponential failures in series, paralleled and series-parallel device configuration and redundancy.
Text Books
1. Montgomery, ‘Introduction to Statistical Quality Control’, John Wiley and Sons, 2007,
Fourth Edition
2. Grant and Leavenworth, ‘Statistical Quality Control’, 7th Edition, 2008McGraw Hill
3. Juran and Gryana, ‘Quality Planning and Analysis’, 5th Ed., THM. 2008
4. NVR Naidu, K. M. Babu and G.Rajendra, ‘Engineering Economy’, New Age International
Pvt. Ltd., 2006.
Reference Books
1. Dale H. Besterfield, ‘Quality Control’, Prentice Hall International, 1998.
2. Kesavan R, ‘Total Quality Management’, I K International, New Delhi-2007J.B.Gupta, ‘A
text book of Transmission and Distribution’, S.K.Kataria and Sons, 1998
Course Outcomes:
The student after completing this course will be able to:
1. Quantify the uncertainties involved in engineering systems and apply the tools of
probability and statistics in analysis and design (PO-1)
2. Discuss the usefulness and theory behind use of Shewart control charts. (PO-1)
3. An ability to discuss concepts of random variation impacting product quality, design a
sampling strategy (PO-1)
4. Apply modern management tools such as total quality management, continuous
improvement and Six Sigma. (PO-1)
5. Describe the importance of quality and prevailing quality philosophy in use today (PO-1)
16
ELECTRIC DRIVES
Subject Code: EE706
Credit: 3: 1: 0
Prerequisites: Knowledge of Electrical Machines & Power Electronics
Course Coordinator/s: Sri. Kodeeswara Kumaran
Contact Hours: 70
Course Objectives:




To study the components of electrical drive system and understand the basics of drive
system control
To learn the operating principles of different types of drive systems like dc shunt/separately
excited motor drive system, induction motor drive system, synchronous motor drive
system, BLDC drive system and stepper motor drives system
To design and analyze simple drive systems
To carry out mini-project in teams for a given set of specifications
Course contents:
UNIT – I
Introduction to Electrical drives
Introduction, advantages of electrical drives, parts of electrical drives, choice of electrical drives,
status of dc and ac drives, dynamics of electrical drives, fundamental torque equation,
components of load torque, nature and classification of load torques, speed-torque conventions
and multi-quadrant operation, equivalent values of drive parameters.
UNIT - II
DC Drives
Basic Concepts: Speed torque characteristics, starting, braking and speed control techniques of
shunt/separately excited dc motor (theory only).
Rectifier controlled dc drives: Types of rectifiers- review, fully controlled rectifier fed dc
drives, half controlled rectifier fed dc drives, multi-quadrant operation of rectifier controlled dc
drives.
Chopper controlled dc drives: Types of choppers – review, chopper controlled dc drives –
motoring and braking operation, multi-quadrant operation of chopper controlled dc drives.
UNIT - III
AC Drives
Basic Concepts: Speed-Torque characteristics of induction motors. Concept of induction motor
starting. Types of starter - star delta, auto transformer, reactor, part winding, rotor resistance.
Concept of induction motor braking. Methods of braking - regenerative, plugging, dynamic
braking (theory only)
Speed control techniques : Rotor resistance control, Stator voltage control, stator frequency
control, V/f control.
Static converter control of induction motors: ac voltage regulator control, voltage source
inverter control, cycloconverter control.
17
UNIT – IV
Special Machine Drives
Synchronous motors : Construction, operation from fixed frequency supply – starting, pulling
in, braking. Synchronous motor variable speed drives. Self-controlled synchronous motor drive
employing load commutated thyristor inverter.
DC brushless motors: Construction, speed-torque characteristics, brushless dc motor controllers
– rotor position measurement, commutation logic, speed controller.
UNIT – V
Stepper Motor Drives: Principle of operation of stepper motor, single stack variable reluctance
motors, speed torque characteristics, control of stepper motors, unipolar and bipolar drive
circuits
Selection of motor power rating: Thermal model of motor for heating and cooling, classes of
motor duty, determination of motor rating.
Selection of parts, control technique for a given drive specification.
Text Book:
1. G.K Dubey, Fundamentals of Electrical Drives, Narosa publishing house Chennai, 2
Edition, 5th reprint.
2. Mohamed A. El-Sharkawi, Fundamentals of Electric Drives, Thomson Learning, 2002
Reference Books:
1. Dave Polka , Motors and Drives : A Practical Technology Guide, The Instrumentation,
Systems and Automation Society, 200.
2. N.K De and P.K. Sen, Electrical Drives, PHI, 2007.
3. M.H.Rashid, ‘Power Electronics: Circuits, Devices and Applications’, Pearson Education,
3rd Edition.
Course Outcomes:
The course will enable the student to,
1. describe the structure of a drive system and analyze the mutliquadrant operation of a
drive system [PO- 1, 2]
2. elucidate the operating principles of dc drives and solve problems related to it [PO- 1, 2]
3. elucidate the operating principles of ac drives and solve problems related to it [PO- 1, 2]
4. explain the functions of drive components and operating principles of special machine
drives (including BLDC motor drive, synchronous motor drive and stepper motor drive)
[PO- 1]
5. suggest required drive components and determine the design parameters for a given drive
system specification [PO- 3]
18
PROTECTION & HIGH VOLTAGE LAB.
Subject Code: EE701L
Credit: 0: 0: 2
Prerequisites: Nil
Contact Hours: 42
Course Coordinator/s: Dr. Pradipkumar Dixit & Sri. C. Ravindra Kumar
Course Objectives





Understand the characteristics of fuse
Understand the characteristics of voltage and current relays
Understand breakdown characteristics of uniform and non-uniform fields.
Understand sphere gap as measuring device
Understand breakdown voltage/strength of liquid and solid insulation
LIST OF EXPERIMENTS:
1. Over current relay: IDMT non-directional characteristics
2. IDMT characteristics of over voltage or under voltage relay (solid state or
electromechanical type)
3. Current-time characteristics of fuse
4. Operating characteristics of microprocessor based(numeric) over-current relay
5. Operating characteristics of microprocessor based(numeric) over/under voltage relay.
6. Motor protection scheme fault studies
7. Field mapping using electrolytic tank for any one-model cable/capacitor/transmission
line/sphere gap models.
8. Flashover characteristics of sphere gaps under AC and DC corrected to STP
9. Determine the breakdown strength of transformer oil
10. Flashover characteristics of non-uniform field gaps under HVAC
11. Measurement of HVAC using sphere gaps
12. Determine the breakdown voltage of solid insulations
Course Outcomes
A student completing this course should be able to:
1.
2.
3.
4.
5.
Demonstrate the characteristics of fuse.(PO-1,4)
Demonstrate the characteristics of voltage and current relays (PO-1,4)
Realize the field distribution of a coaxial cable / parallel plate capacitor.(PO-1,4)
Determine the breakdown voltage of air in uniform and non-uniform fields.(PO-1,4)
Determine the breakdown voltage/strength of solid and liquid insulations.(PO-1,4)
19
POWER SYSTEMS LAB
Subject Code: EE702L
Credit: 0: 0: 2
Prerequisites: Nil
Contact Hours: 42
Course Coordinator/s: Dr.Pradipkumar Dixit & Chandrashekhar Badachi
Course Objectives




Understand power system stability
Realize state of the system through load flow study
Understand the performance of transmission lines
Realize economic load dispatch of a thermal power plant
LIST OF EXPERIMENTS:
1. To plot Swing curve, find the system stability and Critical clearing time for a SMIB
(Using Simulink)
2. Determination of power angle characteristics for salient and non-salient pole synchronous
machines
3. Determination of ABCD Parameters, Regulation and transmission efficiency of
transmission line (Developing GUI)
4. Optimal generator scheduling for thermal power plant
5. Y-bus formation for power systems without mutual coupling by singular transformation
method and inspection method.
6. Fault Analysis (Using standard Software Package)
7. Load flow analysis using Gauss Siedal Method/ Newton–Raphson method
(Two Lab sessions required for each program)
Course Outcomes
After completion of the course, the students will be able to:
1. Determine the power angle characteristics of synchronous machines. Solve the swing
equation and determine the transient stability. (PO-1,4)
2. Determine the transmission line performance (PO-1,4)
3. Obtain economic load dispatch of a thermal power plant (PO-1,4)
4. Conduct a study on power system faults (PO-1,4)
5. Analyse the Power flow of a given system (PO-1,4)
20
M.S. RAMAIAH INSTITUTE OF TECHNOLOGY, BANGALORE – 54
(Autonomous Institute, Affiliated to VTU)
SCHEME OF TEACHING FOR THE ACADEMIC YEAR 2016-2017
VIII SEMESTER B.E. ELECTRICAL AND ELECTRONICS ENGINEERING
Sl.No.
Subject
Subject
Teaching
Code
Category
Credits
Department
L
T
P
Total
1
EE801
Intellectual Property Rights
Electrical & Electronics
Engineering
HSS
2
0
0
2
2
EE802
Entrepreneurship, Management
& Economics
Electrical & Electronics
Engineering
HSS
2
0
0
2
3
EE804
Operations Research
Electrical & Electronics
Engineering
Engineering
Sciences
4
0
0
4
4
EE803
Project
Electrical & Electronics
Engineering
PS(Core)
0
0
16
16
8
0
16
24
Total
L : Lecture
T : Tutorial
P : Practical
21
INTELLECTUAL PROPERTY RIGHTS
Subject Code: EE801
Prerequisites: Nil
Course Coordinator/s: Sri. Vinayaka. V. Rao
Credits: 2: 0: 0
Contact Hours: 28
Course Objectives:





Know the history, laws and Treaties in the field of Intellectual property rights.
Aquent with objectives, regulation, and specification related to patents.
Familiarize with concepts of ownerships, license, and assignment in IPR domain.
Understand the concept of infringements, piracy and remedies against these actions.
Able to draft any product in a patent domain.
Course contents:
Unit I
Basic principles of IP laws: Introduction, concept of property, need for a holistic approach,
constitutional aspects of IP, evolution of the patent system in UK, US and India, basis for
protection, invention, criteria for patentability, non – patentable inventions.
Unit II
Patents: Introduction, origin and meaning of the term patent, objective of a patent law, the
legislative provisions regulating patents, principles underlying the patent law in India, patentable
invention. Inventions which are not patentable, patent of addition, process patent.
Procedure for obtaining patent: Submission of application, filing provisional and complete
specification, publication and examination of the application, communication to the applicant,
opposition proceedings to the grant of the patent, grant and term of patent,
Provisional and complete specification: Definition of Specification, kinds of specification,
provisional specification, complete specification, claims, conditions for amendment.
Unit III
Rights conferred on a patentee: Patent rights, exception and limitations, duties of a patentee.
Transfer of patent: Forms of transfer of Patent rights, assignment, kinds of assignment, license,
kinds of license, rights conferred on a licensee, revocation and surrender of patents.
Infringement of patents: Construction of claims and infringement, patents held to be infringed,
patents held to be not infringed.
Action for Infringement: Where a suit is to be instituted, procedure followed in the suit, onus
of establishment infringement, defence by the defendant, the Relief’s, Injunction, damages or
account of profits, patent agents, drafting of the products, case studies.
Unit IV
Copy Right: Meaning and characteristics of copy right, features of copyright law of 1957,
historical overview, justification for copyright law, subject matter of copyright, concepts,
22
principles, values and interests of the copyright protection, requirement of copy right,
illustrations copy right in literary work, musical work, artistic work, work of architecture,
cinematograph film, sound recording.
Author and Ownership of copy right: Ownership of copy right, contract of service, contract
for service, rights conferred by copy right, terms of copy right, assignment of copy right,
licensing by owners, license in published and unpublished works, License to reproduce certain
works.
Infringement of copy right: Acts which constitute infringement, general principle, direct and
indirect evidence of copying, acts not constituting infringements, infringements in literary,
dramatic and musical works, remedies against infringement of copy right, registration of
copyright, Case studies.
Unit V
Trade Marks: Introduction, Trademark act 1999,meaning,descritpions,functions,need and
essentials of trademark ,some other marks, procedure of registration of trademarks, principles of
registration of trademarks, grounds of refusal, distinctiveness, descriptive and non-descriptive
words, forms of infringement, remedies against infringement of trademarks, case studies.
Industrial Design: Introduction, design act 2000, procedure of registration of a design, piracy of
a registered design, case studies.
Geographical Indicators :salient features of the 1999bill, meaning of GI, prohibited
geographical indicators, grounds of refusal for registration.
Text Books:
1. Dr. T Ramakrishna, “Basic principles and acquisition of Intellectual Property Rights”,
CIPRA, NSLIU -2005.
2. Dr.B.L.Wadehhra, “ Intellectual Property Law Handbook”, Universal Law Publishing Co.
Ltd.,5th edition 2012.
References:
1. Dr. T Ramakrishna , “Ownership and Enforcement of Intellectual Property Rights” ,
CIPRA, NSLIU -2005.
2. “Intellectual Property Law (Bare Act with short comments)”,Universal Law Publishing Co.
Ltd.. 2007.
3. “The Trade marks Act 1999 (Bare Act with short comments)”, Universal Law Publishing
Co. Ltd., 2005.
4. “The Patents Act, 1970 (Bare Act with short comments), as amended by Patents
(Amendment) Rules 2006 w.e.f. 5-5-2006”. Commercial law publishers (India) Pvt. Ltd.,
2006.
5. Thomas T Gordon and Arthur S Cookfair, “Patent Fundamentals for Scientist and
Engineers”, CRC Press 1995.
6. Prabuddha Ganguli, “Intellectual Property Rights”, TMH Publishing Co. Ltd, 2001
23
Course Outcomes
Students completing this course should be able to:
1.
2.
3.
4.
Assess the need, criteria and legal aspects of IPR.(PO-1,6,8)
Understand registration procedures in the IPR domain.(PO-1,6,8)
Apply the drafting concepts for any product of electrical domain. (PO-1,6,8)
Gain awareness on different infringements scenarios and remedial action in IPR domain.(PO1,6,8)
5. Familiarize with latest legal cases in the field of IPR.(PO-1,6,8,10)
24
ENTREPRENEURSHIP, MANAGEMENT & ECONOMICS
Subject Code: EE802
Prerequisites: Nil
Course Coordinator/s: Smt. Aruba Rajan / Ms. Mamatha G M
Credits: 2: 0: 0
Contact Hours: 28
Course Objectives:





To introduce the basic concepts of Management
To understand and study the different functions of Management
To study about managerial economics and market structures
To understand how to set up small business enterprise and write business plan
To know about the method of network analysis and study about PERT and CPM in detail
Course contents:
Unit I
Introduction: Meaning, nature & characteristics of managements Scope & functional areas of
management, Management as a science, art of profession, management & administration, Role of
management, levels of management
Planning: Nature & Importance of planning process, Types of planning & decisions, Importance
of planning, Steps in planning, Hierarchy of plans, Case Studies
Unit II
Organizing& Staffing: Nature & purpose of organization, Types of organization, Departments
& committees.
Centralization & decentralization of authority & responsibility, Nature & importance of staffing,
Process of selection & recruitment
Directing & Controlling: Meaning & nature of directing, Leadership styles, Motivation
theories, Coordination ,Meaning & importance, Steps involved in control essentials of sound
control system, Methods of establishing control, Case Studies
Unit III
Introduction to Economics: Managerial Economics, Nature &Scope, Role of Managerial
Economics in decision Making.
Objectives of Business firma, Alternative Objectives of the firm
Demand Analysis, Law of demand, Exceptions to Law of demand.
Market Structures, Perfect competitions, Monopolic Competitions, Oligopoly competitions
Entrepreneur: Meaning of Entrepreneur, Evolution of the Concept, Functions of an
Entrepreneur, Types of Entrepreneur, Intrapreneur – an emerging Class. Concept of
Entrepreneurship: Evolution of Entrepreneurship, development of Entrepreneurship steps in
entrepreneurial process, Role of entrepreneurs in Economic Development: Entrepreneurship in
India; Entrepreneurship – is Barriers.
25
Unit IV
Small scale industry: Definition; Characteristics; Need and rationale: Objectives: Scope; role of
SSI in Economic Development. Advantages of SSI. Steps to start in SSI – Government policy
towards SSI; Different Policies of S.S.I.; Government Support for S.S.I. during 5 year plans.
Impact of Liberalization, Privatisation, Globalization on S.S.I., Effect of WTO/GATT
Supporting Agencies of Government for S.S.I., Meaning; Nature of Support; Objectives;
Functions; Types of Help, Brief concepts about SEZ & SME.
Unit V
Preparation of Project: Meaning of Project; Project Identification; Project Selection; Project
Report; Need and Significance of Report; Contents; formulation; Guidelines by Planning
Commission for Project report; Network Analysis; Errors of Project Report; Project Appraisal.
Identification of Business Opportunities: Market Feasibility Study; Technical Feasibility Study;
Financial Feasibility Study: Payback period, IRR, Pre-Feasibility Report, Feasibility Report,
Detailed Project Report (D.P.R), Social Feasibility Study
Text Books:
1. P.C.Tripathi, P.N.Reddy, “Principles of Management”, Tata McGraw Hill 4Th Edition.
2. Vasant Desai, “ Dynamics of Entrepreneurial Development & Management”, Himalaya
publishing House .2007 Edition.
3. Jhingam Stephan, “ Managerial Economics”, Vrinda Publication 1998 Edition.
Reference Books:
1. Dr. NVR Naidu and T.KrishnaRao, “Management and Entrepreneurship”- I K
International Publishing House Pvt. Ltd., New Delhi, 2008.
2. Poornima M Charantimath, “Entrepreneurship Development – Small Business
Enterprises”, Pearson Education, 2006.
Course Outcomes:
At the end of the course, the student will be able to:
1. Explicate Management and know its different perspectives. (PO – 11)
2. Interpret the various functions of Management. (PO – 8,9)
3. Know the importance of Managerial Economics in today’s business market.
(PO – 8,10)
4. Cognize the Entrepreneurship and steps involved in the process and the government
policies towards SSI. (PO – 7,9)
5. Identify the project / business opportunities and its demand. (PO –7,10,11)
26
OPERATIONS RESEARCH
Subject Code: EE804
Prerequisites: Nil
Course Coordinator/s: Sri. Ramakrishna Murthy
Credits: 4: 0: 0
Contact Hours: 56
Course Objectives

This Course aims to introduce students to use quantitative methods and techniques for
effective decisions–making; model formulation and applications that can be used in solving
Electrical Engineering, business and decision problems.
Course contents:
Unit I
Introduction: Definition, scope of operations Research (O.R), approach & limitations of O.R
Models, Characteristics and Phases of O.R.
Linear programming problems: Mathematical formulation of L.P problems, graphical solution
methods, special cases in graphical methods. The simplex method, concept of duality, two phase
method, Big M method, dual simplex method, degenerate and procedure for resolving degenerate
cases. (Excluding theorems)
Unit II
Transportation Problems: Basic Feasible solutions by different methods, Fixing optimal
solutions-stepping stone method, MODI method, degeneracy, unbalanced assignment problems,
travelling salesman problems.
Unit III
Game Theory: Two person zero sum game, The Max-Min, Mini-Max principles, game without
Saddle Points, graphical Solutions, dominance property.
Waiting Lines: Operating systems & their characteristics, Poisson queues, M/M/1 queuing
Systems, M/M/K Model. Application to power systems. (excluding derivations)
Unit IV
Replacement Model: Replacement of items whose maintenance cost increases with time
i) When value of money does not changes with time ii) When value of money changes with time,
replacement of items that fail suddenly and group replace policy.
Inventory: Deterministic models with & without shortages, replenishment, meantime, ordering
cost, carrying cost, EOQ.
Unit V
PERT-CPM Technique: Network constructions, determining critical path, Floats, scheduling
by network, project duration, variance under probabilistic modes, prediction of date of
completion, crashing of simple networks, resource leveling by network techniques.
27
Text Books:
1. S.D.Sharma, “Operation Research”, Kedaranath & Ramnath Publications, 5th edtion 2005
2. Kanti Swaroop, “Operation Research”, Sultan Chand Publications 8th edition 2000.
References:
1. Philip Ravindran, “Operation Research”, Wiley Publications, 2nd edition 1987.
2. Hamid Taha, “Introduction to Operation Reaserch”, Pearson 7th edition, 2005.
Course Outcomes
A student completing this course should be able to:
1. Formulate and solve linear programming models. (PO-1,2)
2. Solve transportation and waiting line models. (PO-1)
3. Obtain PERT network and recognize Critical path for a given project. (PO-1,2)
4. Apprehend proper strategy for a given game. (PO-1)
5. Recognize the replacement period of a machine/equipment and EOQ. (PO-1,6)
28
ELECTRICAL DC MACHINE DESIGN AND CAD
Subject Code: EEPE41
Prerequisites : Knowledge of Electrical Machines
Course Coordinator/s: Smt. Kusumika Krori Dutta
Credits: 2: 0: 1
Contact Hours: 56
Course Objectives:




To understand the different types of magnetic and insulating material used in DC machines
and experience the design of main dimension.
Experience the design of armature, and design of field system including winding,
Introduction to CAD software and drawing of lap and wave winding diagram using CAD
software.
Drawing the assembly diagram of DC machine and Visualisation of complete DC machine.
Course contents:
Unit -I
Principles of electrical machine design:
Introduction, considerations for the design of electrical machines, limitations, Different types of
materials and insulators used in electrical machines.
Main dimension design: Output equation, choice of specific loading, choice of number of pole,
design of Main dimensions of the DC machines
Unit II
Design of DC Machine:
Design of armature and slot dimensions, Dimensions of pole body and estimation of number of
turns in the field winding.
Unit III
Simplex & Duplex wave Single layer & Double layer, sequence diagram, pole placement,
commutator segment, brush position, with equalizer.
Unit IV
Simplex & Duplex wave Single layer & Double layer, sequence diagram, pole placement,
commutator segment, brush position, Dummy coil.
Unit V
Assembly and sectional view drawing of pole, yoke, field system, armature of DC machines.
Text Books:
1. A.K.Sawney, “A course in electrical machine design”, Dhanpat Rai and Sons .2005
2. V.N. Mittle,” Design of Electrical Machines”, 4TH edition, Standard Publishers.
3. S.F. Devalapur, “Electrical Drafting”, Eastern Book Promoters, Belgaum,2006
29
Reference Books:
1. R.K Aggarwal , “Principles of Electrical machine design”, 4/e S.K.Kataria & sons.
2. K. L. Narang, ‘Electrical Engineering Drawing’, Satya Prakashan, N.D
Publications, 1993.
Course Outcomes:
At the end of the course, the student will be able to:
1. Design main dimension as well as analyze and interpret data to improve the performance.
( PO 2, 3)
2. Design a machine to meet desired needs within realistic constraints such as economic,
manufacturability and sustainability. ( PO 2,3)
3. Analyze and synthesize lap and wave winding and draw winding table, developed diagram,
sequence diagram, commutator and brushes using conventional approach ( PO 1 , 2)
4. Analyze and synthesize lap and wave winding and draw winding table, developed diagram,
sequence diagram, commutator and brushes using AUTO CAD. (PO 2, 5)
5. Draw assembly diagram using conventional method as well as using AUTOCAD software.(PO 2,5)
30
ELECTROMAGNETIC COMPATIBILITY
Subject Code: EEPE45
Prerequisites: Nil
Course Coordinator/s: Dr. Pradipkumar Dixit
Credits: 3: 0: 0
Contact Hours: 42
Course Objectives





Understand Definition, classification and control of Electric Field Intensity
Understand EMI/EMC Concepts, Definitions, and Requirements
Understand EMC Modeling and Analysis
Understand need and effect of shielding
Understand Electrostatic discharge, EMC protection techniques: grounding and filtering
Course Contents:
Unit-I
Electrostatic field, their control & Estimation:
Electric field intensity, Electric strength, classification of electric fields, Degree of uniformity of
electric fields, control of electric filed intensity, estimation of electric field intensity, Basic
Equation for potential and field intensity in electrostatic fields, Analysis of electrostatic fields in
homogeneous single dielectric medium.
Designing of electromagnetic compatibility: EMC regulation, typical noise path and use of
network theory, Method of noise coupling, miscellaneous noise sources and methods of
eliminating interference.
Unit-II
Cabling: Capacitive coupling, effect of shield on magnetic coupling, mutual inductance effect,
agnatic filed between shield & inner conductor, Shielding to prevent magnetic radiation,
shielding a receptor against magnetic fields, Shield transfer impedance, Coaxial cable vs shielded
twisted pair cables.
Digital circuit radiation: Differential radiation, Common mode radiation, controlling
techniques for Differential & common mode radiation, EMC testing procedures.
Unit –III
Shielding: Near& Far fields, Characteristics& Wave impedance shielding effectiveness,
Absorption loss, Reflection loss, composite absorption & reflection loss, Shielding with
magnetic materials, effects of apertures, conductive windows, coatings, cavity resonance.
Intrinsic noise sources: Thermal noise, contact noise, shot noise & popcorn noise, measuring
random noise, Noise factor, Measurement of noise factor. Digital circuit Noise & layout, Power
Distribution noise
31
Unit-IV
Electrostatic Discharge: Static generation, human body model. Static discharge and ESD
protection in equipment design, Software& ESD protection, ESD Vs EMC.
Contact Protection: Glow discharge, Arc Discharge, Loads with high inrush currents, contact
protection fundamentals Contact protection networks for inductive loads and resistive loads.
Unit-V
Balancing & filters: Balancing, Power supply decoupling, Decoupling filters, High frequency
decoupling, System bandwidth, Modulation and coding.
Grounding: safety grounds, Signal grounds, Single point ground systems, multipoint ground
systems, Functional ground layout, Hardware grounds, Ground loops, Grounding of cable
shields, Guard shields, Guard meters.
EMC applications: RF& Transient Immunity, PCB layout & stack up
Text books:
1. Henry ott., Noise reduction techniques in electronic systems,2nd Edition, Johnwiley 1988.
2. Ravindra Arora, High Voltage insulation engineering, New age International Publication
1995.
Course Outcomes
A student completing this course should be able to:
1. Illustrate electrostatic field control and estimation (PO-1,6)
2. Use network theory in the design of electromagnetic compatibility (PO-1,3)
3. Analyse capacitive coupling and effect of shield on magnetic field.(PO-1)
4. Differentiate sources of radiation and noises.(PO-1)
5. Illustrate ESD, EMC and importance of grounding (PO-1,6)
32
INTRODUCTION TO MULTILEVEL INVERTERS
Subject Code: EEPE47
Prerequisites: Nil
Course Coordinator/s: Ms. Mamatha G M
Credits: 3: 0: 0
Contact Hours: 42
COURSE OBJECTIVES:
 To familiarize the students with general concepts of different types of multilevel inverter
 To make student learn about harmonics and their mitigation
 To introduce the design concepts of multilevel inverter
Unit-I
Two level inverters- Introduction, Sinusoidal PWM-Modulation Scheme, Harmonic Content,
Over modulation , Third Harmonic Injection PWM. Space vector modulation-Switching states,
Space vectors, Dwell times.
Multilevel concepts-fundamentals, general concepts, types of multilevel inverter, comparisons.
Device ratings- switch stress. Output Waveforms- phase voltages, line voltages.
Unit-II
Diode clamped multilevel inverters -principle of operation, features, improved diode clamped
inverter. Three level inverter-configuration, switching state, commutation. Space vector
modulation- dwell time, output waveforms and harmonics. Higher level diode clamped invertersfour and five level diode clamped inverters, with carrier based PWM.
Unit-III
Flying-capacitor multilevel inverters-principle of operation, Salient features- number of
capacitors, capacitor voltage balancing, advantages and disadvantages .
Redundant states- Optimization techniques for capacitor balancing.
NPC/H – bridge inverter-topology- Modulation scheme, waveforms, harmonic content.
Unit-IV
Cascaded H-bridge multilevel inverter- H-bridge inverter- bipolar, unipolar modulation.
Cascaded H-bridge with equal and unequal DC voltages. PWM techniques-harmonics, phase
shifted, level shifted multicarrier modulation, staircase modulation.
Unit-V
Elimination of harmonics- Solution of equations to eliminate harmonics using fourier
transforms.
33
Application of multilevel inverters: Reactive power compensation, back to back intertie,
adjustable speed drives. Elimination of transformers, operation at high power levels.
Textbooks:
1. Muhammad H. Rashid, “Power Electronics, Circuits, Devices and Applications”, 3rd Edition,
Prentice-Hall of India Private Limited, 2004
2. Bin Wu , “High Power Converters and AC drives”, IEEE press. John Wiley and Sons, Inc.
2006
3. Ned Mohan, Tore M. Undeland, Willaim Robbins, “Power Electronics, Converters,
Applications, and design”, 3rd edition, John Wiley and Sons, Inc.2003
References:
1. J. Rodriguez, J. S. Lai and F. Z. Peng, “Multilevel Inverters: Survey of Topologies, Controls,
and Applications,” IEEE Transactions on Industry Applications, vol. 49, no. 4, Aug. 2002,
pp. 724-738.
2. F. Z. Peng, “A generalized multilevel inverter topology with self voltage balancing,” IEEE
Trans. Ind. Application., vol. 37, pp. 611–618, Mar./Apr. 2001.
3. Nabae, I. Takahashi, and H. Akagi, “A New Neutral-point Clamped PWM inverter,” IEEE
Trans. Ind. Application., vol. IA-17, pp. 518-523, Sept./Oct. 1981.
COURSE OUTCOMES:
At the end of the course the student will be able to:
1.
2.
3.
4.
5.
Know and comprehend the concepts, working, waveforms and salient features of
multilevel inverters. (PO- 1)
Interpret the different modulation techniques, configurations of higher level inverters. (PO4)
Analyze different topologies for multilevel inverters with respect to merits and
applications. (PO- 2)
Eliminate the harmonics using appropriate technique. (PO- 2,4,5)
Design high power converters using multilevel inverters. (PO- 3)
34
DIGITAL IMAGE PROCESSING
Subject Code: EEPE49
Prerequisites : Nil
Course Coordinator/s: Smt. Kusumika Krori Dutta
Credits: 2: 0: 1
Contact Hours: 56
Course Objectives:
Upon successful completion of the course, students should be able to:
 Get an introduction to basic concepts and methodologies of Digital Image processing.
 Apply Image enhancement techniques in both spatial and frequency domain methods.
 Extract image features, segmentation and texture from an image.
 Implementation and properties of the different Image transforms.
Course contents:
Unit I
Digital Image Fundamentals: What is Image Processing? Fundamental steps in Digital Image
Processing, Components of an Image Processing System, Elements of Visual Perception, Image
Sensing and Acquisition , Image Sampling and Quantization, Some Basic relationships between
Pixels, Linear and nonlinear operations.
Unit II
Image Enhancement in Spatial Domain: Image Enhancement in Spatial Domain, Some basic
Gray level transformations, Histogram processing, Enhancement using arithmetic/logic
operations.
Unit III
Spatial Filtering : Basics of Spatial filtering , Smoothing spatial filters, Sharpening spatial
filters.
Image Enhancement in frequency domain, Smoothing frequency domain filters, Sharpening
frequency domain filters.
Unit IV
Image Segmentation: Detection of discontinuities, edge linking and boundary detection,
Thresholding region based segmentation.
Unit V
Image Transforms: Two-dimensional orthogonal & unitary transforms, properties of unitary
transforms, two dimensional discrete Fourier transform, Discrete cosine transform, Sine
transform, Hadamard transform, Haar transform, KL transform.
35
Lab Experiments
1.
2.
3.
4.
5.
6.
7.
8.
Basic concepts of Images: Read and display, information about the image.
Image display: Basics, bit planes, quantization and dithering.
Point processing: Arithmetic operation, image negative.
Filtering, create filters, high and low pass filters.
Image geometry: Scaling smaller, rotation.
The fourier transform: two dimensional DFT.
Image segmentation : thresholding, edge detection.
Canny edge detection, second derivatives
Text Book:
1. Rafael C. Gonzalez and Richard E. Woods,” Digital Image Processing”, Pearson
Education, I Ed, 2001 , ISBN-13:9780131687288
Reference Book:
1. Anil K. Jain, “ Fundamentals of Digital Image Processing”, Pearson Education, PHI, 2001,
ISBN-13:9780133361650
Course outcomes:
At the end of the course the student will be able to
1. Describe the processes of Image acquisition and understand processes involved in Image
Processing.( PO 1, 6)
2. Enhance the image in spatial domain extract the information from the given image. (PO
1, 2)
3. Enhance the image using different filters. (PO 2 ,5)
4. Extract image features, segmentation and texture from an image.( PO 2,5)
5. Analyze different types of Image transforms.( PO 2)
36
MODELING & SIMULATION IN ELECTRICAL ENGINEERING
Subject Code: EEPE50
Prerequisites : Nil
Course Coordinator/s: Smt. Aruba Rajan
Credits: 0: 0: 2
Contact Hours: 42
Course Objectives:
The students are trained to
 Analyze electric circuits using MATLAB.
 Understand the characteristics of electric machines
 Perform the analysis on inverters, diodes, etc using Simulink.
 Use the data from other software results
List of experiments:
1. Write a program verify Maximum power transfer and superposition theorem.
2. Write a program to analyze series RLC circuit.
3. Write a program to study the transient nature of a RL series circuit.
4. Write a program to solve a series parallel circuit using mesh analysis.
5. Write a program to solve a series parallel circuit using nodal analysis.
6. Write a program to find output power from a DC motor.
7. Write a program to plot terminal characteristics of a series motor.
8. Write a program to construct a capability curve for an alternator.
9. Develop a Simulink model of an Induction motor and obtain its torque slip characteristics.
10. Write a program to verify the truth table for a logic circuit.
11. Write a program to calculate and plot the amplitude and phase response of a High pass
filter/ low pass filter/band pass filter as a function of frequency.
12. Write a program to get the impulse response of a discrete system and obtain a convolute
output for a given sequence.
13. Write a program to solve simultaneous equations with sparse matrix.
14. Create a GUI that can read an input data set from a file and perform a least squares fit to
the data.
15. Control a DC motor using a P/PI/PID controller using Simulink.
16. Write a program to get step response for a given system using state space model
17. Perform a harmonic analysis of a single phase PWM inverter using Simulink.
18. Develop a Simulink model for diode rectifier with RL load.
19. Construct a Simulink model for an automatic voltage regulator (AVR) system and obtain
the step response.
20. Introduction to PSCAD - MATLAB Interface .
Course Outcomes:
At the end of the course, the students are able to
1. Program and analyze any electric circuit using MATLAB and Simulink (PO-1,4,5)
2. Use the salient features of MATLAB and Simulink (PO-1,4,5)
3. Interpret the simulation results of PSCAD and analyze in MATLAB.(PO-1,4,5)
37
Open Electives offered to other Departments
Introduction to MEMS
Subject Code: EEOE01
Prerequisites: Nil
Course Coordinator/s: Dr. Premila Manohar
Credits: 3: 0: 0
Contact Hours: 42
Course Objectives




Introduce various aspects of micro systems and scaling effects.
Familiarize the students with micro fabrication, modeling and simulation.
Reminisce electronic amplifiers, signal conditioning and control theory.
Create an awareness about some of the MEMs applications.
Course contents:
Unit I
Introduction to micro systems, smart materials, structures and systems. Micro and smart devices
and systems: Transduction Principles ( eg electrostatic sensing and actuation, thermal sensing
and actuation, piezo resistive sensor, piezoelectric sensing and actuation and magnetic actuation
etc), Scaling effects
Unit II
Introduction, fabrication processes, thin film deposition, lithography, etching, Si micro
machining, surface and bulk micromachining. Thick film processing and specialized materials.
Unit III
Bar, beam, stress and strain, analysis of beams under simple loading, torsional deflections,
residual stresses and stress gradient, Introduction to finite element method.
CAD tools (Comsol and Intellisuite)
Unit IV
Semiconductor devices, electronic amplifiers, signal conditioning, control theory for smart
systems, integration and packaging.
Unit V
Silicon capacitive accelerometer, piezoresistive pressure sensor, Conductometric gas sensor,
electrostatic comb drive, magnetic micro relay, portable blood analyser, piezoelectric inkjet print
head, micro mirror array.
Laboratory Demonstrations of BEL pressure sensor, Active vibration Control,
38
Text Book
1. Ananth Suresh et al, Micro and Smart Systems Technology, Wiley India, 2010
References
1. T R Hsu, MEMS and Microsystems Design and Manufacturing, Tata McGraw Hill, 2nd
Edition, 2008 (1st Edition is also ok)
2. Chang Liu, Foundations of MEMS, Pearson International Edition, 2006
3. S D Senturia,Micro system design, Springer International Edition, 2001
Course Outcomes
At the end of the course students should
1. Have learnt various transduction principles, smart systems, smart materials and effect of
scaling. (PO-1)
2. Be familiar with various micro fabrication techniques. (PO-1)
3. Have learnt the basics of mechanical modeling, finite element analysis and simulation tools
for MEMS. (PO-1,5)
4. Appreciate the application, interface electronics, signal conditioning and control aspects as
applicable to MEMS. (PO-1)
5. Understand the working of some of the micro system. (PO-1)
39