LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 1 08.07.2015
Hi-lume® A-Series Driver Overview
Forward Phase Control
The Hi-lume® A-Series Driver is a high-performance
LED driver that provides smooth, continuous
1% dimming for constant current LED modules.
Features
•Continuous, flicker-free dimming from 100% to 1%.
•Guaranteed compatibility with selected HomeWorks®,
GRAFIK Eye® QS, and GRAFIK SystemsTM dimmers.
Please see the chart “Compatible Controls” at the end
of this document or contact Lutron Asuka for details
regarding compatible controls.
•100% performance-tested at factory.
•A rated lifetime of 50 000 hours @ tc = 65 °C.
•PSE Certified.
•RoHS Compliant.
•Pulse width modulation (PWM) or constant current
reduction (CCR) dimming methods available. See
Application Note #360 for details.
•For more information please go to:
www.lutron.com/HilumeLED
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Hi-lume® A-Series, case type K
76 mm W × 25 mm H × 124 mm L
Page
1
LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 2 08.07.2015
Specifications
Standards
Performance
•Dimming Range: 100% to 1%
•Operating Voltage: 100 V~ at 50/60 Hz (Forward
Phase Control)
•A rated lifetime of 50,000 hours @ tc = 149 °F (65 °C).
– For rated warranty, tc not to exceed the
maximum rated temperatures. 1
•Patented thermal foldback protection.
•LEDs turn on to any dimmed level without going to full
brightness.
•Nonvolatile memory restores all driver settings after
power failure.
•Power Factor: > 0.90 at 40 W
•Total Harmonic Distortion (THD): < 20% at 40 W
•Inrush Current: < 2 A
•Inrush Current Limiting Circuitry: eliminates circuit
breaker tripping, switch arcing and relay failure.
•Open circuit protected
•Short circuit protected
•Turn-on time: ≤ 1.5 seconds 2
•PWM Dimming Frequency: 550 Hz
Environmental
•Sound Rating: Class A.
•Relative Humidity: Maximum 90% non-condensing.
•Minimum operating ambient temperature (ta) = 0 °C.
•Meets IEEE C62.41 category A surge protection
standards up to and including 4 kV.
•Manufacturing facilities employ ESD reduction
practices that comply with the requirements of
ANSI/ESD S20.20.
•Lutron® Quality Systems registered to ISO 9001.2008.
•H PSE certified.
Driver Wiring and Mounting
•Driver is grounded by a mounting screw to the
grounded fixture or by terminal connection.
•Terminal blocks on the driver accept one solid wire
per terminal from Ø 1.024 mm (18 AWG) to Ø 1.29 mm
(16 AWG).
•Fixture must be grounded in accordance with local
and national electrical codes.
•Do not use more than 1 wire per connector terminal.
Connector terminals are not rated for daisy-chain
wiring.
•Maximum driver-to-LED light engine wire length for
Constant Current Drivers:
Maximum Lead Length
200 mA to 700 mA 710 mA to 1.50 A
1.024 mm (18 AWG) 9 m
4.5 m
1.29 mm (16 AWG) 10.5 m
7.5 m
1.63 mm (14 AWG) 15 m
12 m
2.05 mm (12 AWG) 30 m
18 m
Wire Gauge Ø
Note: For wire gauges larger than Ø 1.29 mm (16 AWG), use external
connector for connection with driver
1
2
Installer is responsible for ensuring that the driver case temperature does not exceed the maximum rated temperature.
Models available with turn-on time ≤ 1 second.
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
2
LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 3 08.07.2015
How to Build a Model Number: Hi-lume® A-Series
LTEA3D11K — – — — ———
Case Style:
S = Studded
N = Non-Studded
Example: LTEA3D11KN-JA100
For further assistance selecting your model number,
contact Lutron Asuka at 03.5575.8411 (phone),
0120.083.417 (freephone), or asuka@lutron.com
Current Level (for Constant Current):
020 = 0.20 A; 021 = 0.21 A … 100 = 1.00 A … 150 = 1.50 A
Driver Output:
C = Constant current driver with pulse width modulation (PWM) dimming
A = Constant current driver with constant current reduction (CCR) dimming
LED Driver Output Range (see the following pages for more detail):
Constant Current
G = 0.20 A – 0.70 A 8 V – 20 V
H = 0.20 A – 0.70 A 15 V – 38 V
I = 0.71 A – 1.05 A 8 V – 20 V
J = 0.71 A – 1.05 A 15 V – 38 V
K = 1.06 A – 1.50 A 8 V – 20 V
L = 1.06 A – 1.50 A 15 V – 38 V
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
3
LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 4 08.07.2015
“G” Output Range, Current Driver Models
Driver Type
Output Dimming Method
Output Voltage Output Current Output Power Standards Recognition
Constant Current Pulse Width Modulation (PWM)
8 – 20 V
0.20 – 0.70 A
2 – 14 W
Driver (Class 2)
Constant Current Reduction (CCR)
H
Current Driver Operation Range:
Output Power vs. Output Current
60
40
50
35
32
30
Output Power (W)
Output Voltage (V)
Output Voltage vs. Output Current
40
38
30
20
25
20
15
20 V Max.
10
G
10
8
0
0
0.2 0.35 0.7 1.05 1.4
1.5
1.75 2.1
Output Current (A)
G
5
3
8 V Min.
0
0
0.2 0.35 0.7 1.05 1.4
1.5
1.75 2.1
Output Current (A)
Typical Performance Specifications:
Parameter
Input Current
Power Factor
THD
Driver Efficiency
80
Value
186 mA
0.99
< 20% for loads greater than 10 W
76%
Driver Efficiency vs. Output Power at 100 V~
0.70 A
75
0.50 A
70
Efficiency (%)
Test Conditions
ta = 25 °C,
0.70 A 14 W load,
Max. Light Output,
K enclosure
100 V~ without a control
0.35 A
65
60
0.20 A
55
50
45
40
2468
10
12
14
Output Power (W)
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
4
LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 5 08.07.2015
“H” Output Range, Current Driver Models
Driver Type
Output Dimming Method
Output Voltage Output Current Output Power Standards Recognition
Constant Current Pulse Width Modulation (PWM)
15 – 38 V PWM
0.20 – 0.70 A
3 – 26 W
Driver (Class 2)
Constant Current Reduction (CCR) 15 – 38 V-
H
Current Driver Operation Range:
Output Power vs. Output Current
60
40
50
35
32
30
Output Power (W)
Output Voltage (V)
Output Voltage vs. Output Current
40
38
30
H
20
25
15
10
10
8
0
0
0.2 0.35 0.7 1.05 1.4
1.5
1.75 2.1
Output Current (A)
38 V Max.
20
H
5
15 V Min.
3
0
0
0.2 0.35 0.7 1.05 1.4
1.5
1.75 2.1
Output Current (A)
Typical Performance Specifications:
Parameter
Input Current
Power Factor
THD
Driver Efficiency
Value
325 mA
0.99
< 20% for loads greater than 10 W
80%
Test Conditions
ta = 25 °C,
0.70 A 26 W load,
Max. Light Output,
K enclosure
100 V~ without a control
Driver Efficiency vs. Output Power at 100 V~
85
Efficiency (%)
0.70 A
0.45 A
80
75
70
0.20 A
65
60
55
50
0
5
®
Job Name:
Job Number:
10
15
Output Power (W)
20
25
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
30
Page
5
LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 6 08.07.2015
“I” Output Range, Current Driver Models
Driver Type
Output Dimming Method
Output Voltage Output Current Output Power Standards Recognition
Constant Current Pulse Width Modulation (PWM)
8 – 20 V
0.71 – 1.05 A
6 – 21 W
Driver (Class 2)
Constant Current Reduction (CCR)
H
Current Driver Operation Range:
Output Power vs. Output Current
60
40
50
35
32
30
Output Power (W)
Output Voltage (V)
Output Voltage vs. Output Current
40
38
30
20
10
8
20
15
10
I
0
0
0.2 0.35 0.7 1.05 1.4
1.5
1.75 2.1
Output Current (A)
20 V Max.
25
I
5
8 V Min.
3
0
0
0.2 0.35 0.71 1.05 1.4
1.5
1.75 2.1
Output Current (A)
Typical Performance Specifications:
Parameter
Input Current
Power Factor
THD
Driver Efficiency
80
Value
268 mA
0.99
< 20% for loads greater than 10 W
78%
Test Conditions
ta = 25 °C,
1.05 A 21 W load,
Max. Light Output,
K enclosure
100 V~ without a control
Driver Efficiency vs. Output Power at 100 V~
1.05 A
0.71 A
75
Efficiency (%)
70
65
60
55
50
45
40
0
9
®
Job Name:
Job Number:
12
15
Output Power (W)
18
21
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
6
LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 7 08.07.2015
“J” Output Range, Current Driver Models
Driver Type
Output Dimming Method
Output Voltage Output Current Output Power Standards Recognition
Constant Current Pulse Width Modulation (PWM)
15 – 38 V PWM
0.71 – 1.05 A
11 – 32 W
Driver (Class 2)
Constant Current Reduction (CCR) 15 – 38 V-
H
Current Driver Operation Range:
Output Power vs. Output Current
60
40
50
35
32
30
32 V Max.
Output Power (W)
Output Voltage (V)
Output Voltage vs. Output Current
40
38
30
J
20
38 V Max.
25
20
J
15
10
10
8
0
0
0.2 0.35 0.7 1.05 1.4
1.5
1.75 2.1
Output Current (A)
5
15 V Min.
3
0
0
0.2 0.35 0.7 1.05 1.4
1.5
1.75 2.1
Output Current (A)
Typical Performance Specifications:
Parameter
Input Current
Power Factor
THD
Driver Efficiency
Value
400 mA
0.99
< 20%
80%
Test Conditions
ta = 25 °C,
1.05 A 32 W load,
Max. Light Output,
K enclosure
100 V~ without a control
Driver Efficiency vs. Output Power at 100 V~
Efficiency (%)
90
85
0.71 A
80
0.90 A
1.05 A
75
70
65
60
10
15
®
Job Name:
Job Number:
20
25
Output Power (W)
30
35
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
7
LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 8 08.07.2015
“K” Output Range, Current Driver Models
Driver Type
Output Dimming Method
Output Voltage Output Current Output Power Standards Recognition
Constant Current Pulse Width Modulation (PWM)
8 – 20 V
1.06 – 1.50 A
9 – 30 W
Driver (Class 2)
Constant Current Reduction (CCR)
H
Current Driver Operation Range:
Output Power vs. Output Current
60
40
50
35
32
30
Output Power (W)
Output Voltage (V)
Output Voltage vs. Output Current
40
38
30
20
20 V Max.
25
20
K
15
10
K
10
8
0
0
0.2 0.35 0.7 1.05 1.4
1.5
1.75 2.1
Output Current (A)
8 V Min.
5
3
0
0
0.2 0.35 0.71 1.05 1.4
1.5
1.75 2.1
Output Current (A)
Typical Performance Specifications:
Parameter
Input Current
Power Factor
THD
Driver Efficiency
80
Value
392 mA
0.99
< 20% for loads greater than 10 W
77%
Test Conditions
ta = 25 °C,
1.50 A 30 W load,
Max. Light Output,
K enclosure
100 V~ without a control
Driver Efficiency vs. Output Power at 100 V~
1.06 A
1.20 A
1.50 A
75
Efficiency (%)
70
65
60
55
50
45
40
0 11 1315 17 19 2123 25 2729
Output Power (W)
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
8
LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 9 08.07.2015
“L” Output Range, Current Driver Models
Driver Type
Output Dimming Method
Output Voltage Output Current Output Power Standards Recognition
Constant Current Pulse Width Modulation (PWM)
15 – 38 V PWM
1.06 – 1.50 A
16 – 32 W
Driver (Class 2)
Constant Current Reduction (CCR) 15 – 38 V-
H
Current Driver Operation Range:
Output Power vs. Output Current
60
40
50
35
32
30
40
38
Output Power (W)
Output Voltage (V)
Output Voltage vs. Output Current
32 V Max.
30
20
L
25
L
20
15
10
10
8
0
0
0.2 0.35 0.7 1.05 1.4
1.5
1.75 2.1
Output Current (A)
15 V Min.
5
3
0
0
0.2 0.35 0.7 1.05 1.4
1.5
1.75
Output Current (A)
Typical Performance Specifications:
Parameter
Input Current
Power Factor
THD
Driver Efficiency
Value
420 mA
0.99
< 20%
75%
Test Conditions
ta = 25 °C,
1.50 A 32 W load,
Max. Light Output,
K enclosure
100 V~ without a control
Driver Efficiency vs. Output Power at 100 V~
Efficiency (%)
90
85
1.06 A
1.20 A
1.50 A
80
75
70
65
60
151719 2123 2527293133
Output Power (W)
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
9
LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 10 08.07.2015
K Case: Case Dimensions
J*
C
A
I*
H*
B
E
D
F
G
K Case: Connector Location Dimensions
K*
O
L
P
K*
8 – 32
Threaded
Studs*
L
M
Q
N
R*
Q
A
B
C
D
E
107 mm
25 mm
76 mm
124 mm
117 mm
(mounting center)
F
G
H* I* J*
36 mm
51 mm
28 mm
51 mm
41 mm
K* 8.3 mm
L 16.5 mm
M 19 mm
N 44 mm
O 34 mm
P
Q
R* 19 mm
8 mm
7 mm
* Applies to studded K case only.
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
10
LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 11 08.07.2015
K Case: Side Entry Connector Location Dimensions (Non-Studded)
S
T
S
T
U
V
35 mm
16 mm
22 mm
39 mm
U
V
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
11
LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 12 08.07.2015
Wiring Diagram for Forward Phase Control
+V2 (Red)
Dimmed Hot (Black)
Neutral (White)
To Forward Phase
Dimming Control
Hi-lume ®
A-Series
Ground1
LED light engine
–V2 (Black)
Ground1 (Green)
Note: Colors shown correspond to terminal blocks on driver.
1Fixture
2
and driver case must be grounded.
For maximum driver–to–LED light engine wire length, see chart in Driver Wiring and Mounting section.
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
12
LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 13 08.07.2015
Compatible Controls
•Guaranteed performance specifications with the controls listed in the chart below.
•For assistance selecting controls, contact Lutron Asuka at 03.6866.8444 (phone), 0120.083.417 (freephone), or
asuka@lutron.com
Product
Part Number
HomeWorks® 500 W dimmer
GRAFIK Eye® QS1
HWD-5ND-JA
QSGR-3PJA
QSGR-4PJA
QSGR-6PJA
GRX-3102-x-JA-xx 2 – 10 (per output)
GRX-3103-x-JA-xx 26 total per unit
GRX-3104-x-JA-xx
GRX-3106-x-JA-xx
GRX-3502-x-JA-xx
GRX-3503-x-JA-xx
GRX-3504-x-JA-xx
GRX-3506-x-JA-xx
LP-RPM-4U-120
2 – 26 (per output)
26 total per module
LP-RPM-4A-120
1 – 13 (per output)
26 total per module
GP-4-2L-JA
1 – 26 (per output)
JDPxx-xxxxx
GRAFIK Eye® 30002
RPM-4U Module3
(LCP Combo, GRAFIK SystemsTM)
RPM-4A Module3
(LCP Combo, GRAFIK SystemsTM)
GRAFIK SystemsTM Dimming Panels3
Fixtures per Control
(100 V~ only)
1–8
2 – 10 (per output)
26 total per unit
Measured Light
Output Range
100% – 1%
100% – 1%
100% – 1%
100% – 1%
100% – 1%
100% – 1%
1
Set load type to “Fluorescent Module”
Set load type to “GRX-FDBI or GRX-TVI”
3 Set load type to “ 2-1”
2
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
13
LED Dimming Driver
Hi-lumeTM A-Series LTE – Japan
Architectural Dimming
369677e 14 08.07.2015
Electricians and Contractors
Facilities Managers
Driver Leads
SERVICE
Maximum driver-to-LED light engine wire length for
Constant Current Drivers:
Warranty
Maximum Lead Length
Wire Gauge Ø
200 mA to 700 mA 710 mA to 1.50 A
1.024 mm (18 AWG) 9 m
4.5 m
1.29 mm (16 AWG) 10.5 m
7.5 m
1.63 mm (14 AWG) 15 m
12 m
2.05 mm (12 AWG) 30 m
18 m
Note: For wire gauges larger than Ø 1.29 mm (16 AWG), use external
connector for connection with driver
Wiring and Grounding
•Driver must be grounded.
•Drivers must be installed per national and local
electrical codes.
LED Light Engine Replacement
For warranty information, please contact Lutron
Asuka.
Replacement Parts
When ordering Lutron® replacement parts please
provide the full model number. Contact Lutron Asuka if
you have any questions.
Further Information
For further information, please visit us at
http://www.lutron.jp.
You may contact Lutron Asuka at:
03.6866.8444 (phone),
0120.083.417 (freephone) or
asuka@lutron.com
The LED light engine can be changed while the driver
is installed and powered.
Maximum Driver Operating Temperature
For 50,000 hour lifetime, driver case temperature (tc)
must not exceed 65 °C.
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page
14