A3503 datasheet - Allegro Microsystems

advertisement
A3503
Ratiometric Linear Hall Effect Sensor IC
Discontinued Product
These parts are no longer in production The device should not be
purchased for new design applications. Samples are no longer available.
Date of status change: October 31, 2005
Recommended Substitutions:
The drop-in replacement is the A1302, with a more sensitive option also
available, the A1301.
NOTE: For detailed information on purchasing options, contact your
local Allegro field applications engineer or sales representative.
Allegro MicroSystems, Inc. reserves the right to make, from time to time, revisions to the anticipated product life cycle plan for a
product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The information
included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor
for any infringements of patents or other rights of third parties which may result from its use.
Data Sheet
27501D
3503
RATIOMETRIC, LINEAR
HALL-EFFECT SENSOR ICS
The UGN3503LT, UGN3503U, and UGN3503UA Hall-effect
sensor ICs accurately track extremely small changes in magnetic flux
density—changes generally too small to operate Hall-effect switches.
X
For motion detectors, gear tooth sensors, and proximity detectors,
they are magnetically driven mirrors of mechanical events. As sensitive
monitors of electromagnets, they can effectively measure a system's
performance with negligible system loading while providing isolation
from contaminated and electrically noisy environments.
2
3
OUTPUT
1
GROUND
CC
SUPPLY
V
Dwg. PH-006
Pinning is shown viewed from branded side.
Each Hall-effect integrated circuit includes a Hall element,
linear amplifier, and emitter-follower output stage. Problems associated
with handling tiny analog signals are minimized by having the Hall cell
and amplifier on a single chip.
Three package styles provide a magnetically optimized package for
most applications. Package suffix ‘LT’ is a miniature SOT-89/TO243AA transistor package for surface-mount applications; suffix ‘U’ is a
miniature three-lead plastic SIP, while ‘UA’ is a three-lead ultra-miniSIP. All devices are rated for continuous operation over the temperature
range of -20°C to +85°C.
FEATURES
■
■
■
■
■
Extremely Sensitive
Flat Response to 23 kHz
Low-Noise Output
4.5 V to 6 V Operation
Magnetically Optimized Package
ABSOLUTE MAXIMUM RATINGS
Supply Voltage, VCC ............................. 8 V
Magnetic Flux Density, B ......... Unlimited
Operating Temperature Range,
TA ............................ -20°C to +85°C
Storage Temperature Range,
TS ........................... -65°C to +150°C
Always order by complete part number, e.g., UGN3503UA .
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSOR ICS
FUNCTIONAL BLOCK DIAGRAM
1 VCC
REG.
X
3
OUTPUT
2
GROUND
Dwg. FH-007
ELECTRICAL CHARACTERISTICS at TA = +25°C, VCC = 5 V
Limits
Characteristic
Symbol
Test Conditions
Min.
Typ.
Max.
Units
Operating Voltage
VCC
4.5
—
6.0
V
Supply Current
ICC
—
9.0
13
mA
Quiescent Output Voltage
VOUT
B=0G
2.25
2.50
2.75
V
Sensitivity
∆VOUT
B = 0 G to ±900 G
0.75
1.30
1.75
mV/G
—
23
—
kHz
—
90
—
µV
—
50
220
Ω
Bandwidth (-3 dB)
BW
Broadband Output Noise
Vout
Output Resistance
ROUT
BW = 10 Hz to 10 kHz
All output-voltage measurements are made with a voltmeter having an input impedance of at least 10 kΩ.
Magnetic flux density is measured at most sensitive area of device located 0.0165" (0.42 mm) below the branded face of the ‘U’
package; 0.0195" (0.50 mm) below the branded face of the ‘UA’ package; and 0.0305" (0.775 mm) below the branded face of the
‘LT’ package.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Copyright © 1985, 2002 Allegro MicroSystems, Inc.
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSOR ICS
OUTPUT VOLTAGE AS A
FUNCTION OF TEMPERATURE
OUTPUT NOISE AS A
FUNCTION OF FREQUENCY
4.0
10
OUTPUT IN VOLTS
OUTPUT NOISE IN µ Vrms √HZ
VCC = 5V
3.5
B= +500G
3.0
B = 0G
2.5
2.0
40
20
0
+25
+85
6.0
4.0
2.0
10
100
FREQUENCY IN HZ
Dwg. A-12,573
SUPPLY CURRENT AS A
FUNCTION OF SUPPLY VOLTAGE
12
TA = +25°C
10
9.0
1K
10K
Dwg. A-12,505
DEVICE SENSITIVITY AS A
FUNCTION OF SUPPLY VOLTAGE
2.5
TYPICAL SENSITIVITY IN V/G
B = 0G
11
0
+125
AMBIENT TEMPERATURE IN C
SUPPLY CURRENT IN mA
VCC = +5V
TA = +25°C
B= -500G
1.5
TA = +25°C
2.0
1.5
1.0
0.5
8.0
7.0
4.5
5.0
5.5
SUPPLY VOLTAGE IN VOLTS
0
6.0
B = 0G
TA = +25°C
3.0
2.0
1.0
0
4.5
5.0
5.5
SUPPLY VOLTAGE IN VOLTS
6.0
Dwg. A-12,508
www.allegromicro.com
5.0
5.5
SUPPLY VOLTAGE IN VOLTS
6.0
Dwg. A-12,507
LINEARITY AND SYMMETRY AS A
FUNCTION OF SUPPLY VOLTAGE
100
LINEARITY AND SYMMETRY IN PERCENT
5.0
4.0
4.5
Dwg. A-12,506
OUTPUT NULL VOLTAGE AS A
FUNCTION OF SUPPLY VOLTAGE
OUTPUT NULL VOLTAGE IN VOLTS
8.0
OUTPUT SYMMETRY
99
98
W
ITY BELO
LINEAR
G
B = -900
NULL
LL
VE NU
ITY ABO
LINEAR
G
B = +900
97
TA = +25°C
96
95
4.5
5.0
5.5
SUPPLY VOLTAGE IN VOLTS
6.0
Dwg.A-12,509
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSOR ICS
OPERATION
NOTCH SENSING
Dwg. A-12,574
GEAR TOOTH SENSING
The output null voltage (B = 0 G) is nominally one-half the supply voltage. A
south magnetic pole, presented to the branded face of the package will
drive the output higher than the null voltage level. A north magnetic pole will
drive the output below the null level.
In operation, instantaneous and proportional output-voltage levels are
dependent on magnetic flux density at the most sensitive area of the device.
Greatest sensitivity is obtained with a supply voltage of 6 V, but at the cost of
increased supply current and a slight loss of output symmetry. The device's output
is usually capacitively coupled to an amplifier that boosts the output above the
millivolt level.
In two applications shown, a permanent bias magnet is attached with epoxy
glue to the back of the epoxy package. The presence of ferrous material at the face
of the package acts as a flux concentrator.
The south pole of a magnet is attached to the back of the package if the Halleffect IC is to sense the presence of ferrous material. The north pole of a magnet is
attached to the back surface if the integrated circuit is to sense the absence of
ferrous matrial.
Calibrated linear Hall devices, which can be used to determine the actual flux
density presented to the device in a particular application, are available.
ELEMENT LOCATIONS
N
SUFFIX "U"
AC T IV E AR E A DE P T H
0.0165"
0.42 mm
0.093"
2.37 mm
NOM
3 2
0.072"
1.83 mm
1
Dwg. A-12,512
A
CURRENT MONITORING
B R ANDE D
S UR F AC E
1
2
3
Dwg. MH-002-5D
SUFFIX "LT"
AC T IV E AR E A DE P T H
0.0305"
0.775 mm
NOM
SUFFIX "UA"
AC T IV E AR E A DE P T H
0.0195"
0.50 mm
NOM
0.091"
2.32 mm
0.081"
2.06 mm
0.042"
1.08 mm
0.059"
1.50 mm
A
A
1
2
3
B R ANDE D
S UR F AC E
1
2
3
Dwg. A-12,513
Dwg. MH-008-9A
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Dwg. MH-011-3D
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSOR ICS
UGN3503LT
(SOT89/TO-243AA)
Dimensions in Inches
(for reference only)
0.181
0.173
0.072
0.064
0.167
0.155
2
1
0.063
0.055
3
0.102
0.090
0.059
BSC
4.60
4.40
1.83
1.62
0.0173
0.0138
0.090
0.084
4.25
3.94
0.0189
0.0142
0.0221
0.0173
0.047
0.035
Dimensions in Millimeters
(controlling dimensions)
1
1.20
0.89
BSC
0.48
0.36
BSC
B
0.031
Dwg. MA-009-3A mm
0.102
0.8
2.6
A
4.6
0.181
2
2.29
2.13
2.5
2.0
A
1
0.44
0.35
3.00
Dwg. MA-009-3A in
0.098
0.079
B
2.60
2.29
3
0.56
0.44
1.50
0.118
BSC
2
1.60
1.40
3 0.047
0.028
TYP
1
0.7
0.031
TYP
TYP
2
3
1.2
0.8
TYP
Pads 1, 2, 3, and A — Standard SOT89 Layout
Pads 1, 2, 3, and B — Low-Stress Version
Pads 1, 2, and 3 only — Lowest Stress, But Not Self Aligning
Pads 1, 2, 3, and A — Standard SOT89 Layout
Pads 1, 2, 3, and B — Low-Stress Version
Pads 1, 2, and 3 only — Lowest Stress, But Not Self Aligning
Dwg. MA-012-3 in
Dwg. MA-012-3 mm
NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown.
2. Supplied in bulk pack (500 pieces per bag) or add "TR" to part number for tape and reel.
3. Only low-temperature (≤240°C) reflow-soldering techniques are recommended for SOT89 devices.
www.allegromicro.com
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSOR ICS
UGN3503U
Dimensions in Inches
(controlling dimensions)
Dimensions in Millimeters
(for reference only)
0.183
0.178
4.65
4.52
1.60
1.50
0.063
0.059
4.60
4.47
0.181
0.176
45°
45°
0.086
MAX
1
2
0.018
3
0.0173
0.0138
0.600
0.560
0.0189
0.0142
SEE NOTE
2.18
MAX
1
2
0.46
3
0.44
0.35
15.24
14.23
0.48
0.36
SEE NOTE
1.27
2.54
0.050
0.100
Dwg. MH-003E in
Dwg. MH-003E mm
Devices in the ‘U’ package are
NOT RECOMMENDED FOR NEW DESIGN
NOTES: 1. Tolerances on package height and width represent allowable mold offsets.
Dimensions given are measured at the widest point (parting line).
2. Exact body and lead configuration at vendor’s option within limits shown.
3. Height does not include mold gate flash.
4. Recommended minimum PWB hole diameter to clear transition area is 0.035" (0.89 mm).
5. Minimum lead length was 0.500" (12.70 mm). If existing product to the original specifications is not acceptable,
contact sales office before ordering.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSOR ICS
UGN3503UA
Dimensions in Millimeters
(for reference only)
Dimensions in Inches
(controlling dimensions)
0.164
0.159
4.17
4.04
0.062
0.058
45°
0.122
0.117
0.085
MAX
3.10
2.97
45°
1
2
3
0.031
2.16
MAX
0.640
0.600
0.0189
0.0142
45°
1
2
0.44
0.35
0.48
0.36
SEE NOTE
1.27
0.050
BSC
0.79
3
16.26
15.24
0.0173
0.0138
SEE NOTE
1.57
1.47
45°
BSC
Dwg. MH-014E in
NOTES: 1. Tolerances on package height and width represent
allowable mold offsets. Dimensions given are
measured at the widest point (parting line).
2. Exact body and lead configuration at vendor’s option
within limits shown.
3. Height does not include mold gate flash.
4. Recommended minimum PWB hole diameter to clear
transition area is 0.035" (0.89 mm).
5. Where no tolerance is specified, dimension is nominal.
6. Supplied in bulk pack (500 pieces per bag).
Dwg. MH-014E mm
Radial Lead Form (order UGN3503UA-LC)
1
2
3
0.620"
0.500"
(15.7 mm
12.7 mm)
0.100"
(2.5 mm)
0.108"
(2.74 mm)
Dwg. MH-026
NOTE: Lead-form dimensions are the nominals produced on the
forming equipment. No dimensional tolerance is implied or
guaranteed for bulk packaging (500 pieces per bag).
www.allegromicro.com
3503
RATIOMETRIC,
LINEAR
HALL-EFFECT SENSOR ICS
Allegro MicroSystems, Inc. reserves the right to make, from time to
time, such departures from the detail specifications as may be
required to permit improvements in the design of its products.
The information included herein is believed to be accurate and
reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of
third parties which may result from its use.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Download