A1-A01-A02-A03 series
Industrial controls
Distinctive features
UG1410A-R1
The A01 and A02 series offer ranges of :
- pushbutton switches, illuminated or not
- indicators
- 2 or 3 position keylock switches
- 2 or 3 position rotary lever switches
with rectangular, square or round operators.
❑ Environmental protection : IP65
❑ Modular construction
❑ Electrical life : 50.000 cycles min.
❑ Screen engraving or insertable legends on request
❑ Approvals (for switch blocks only)
UL 1054
BS RIA 20 Shock & Vibration
EN 61058-1
Each sub-assembly has
to be ordered separately.
A01 - A1 - A03 series
G
A02 series
• Panel cut-out :
Ø 16 mm (.630), except :
- flush mount round : Ø 22 mm (.866)
- flush mount rectangular : 20.60 x 26.70 mm
- flush mount square : 20.60 x 20.60 mm
- A1 series : Ø 22 mm (.866)
- A03 series : round or square Ø 22 (.866)
flush mount : Ø 30 mm (1.378)
• Panel cut-out :
- round or square : Ø 22 mm (.866)
- rectangular : 29,5 x 21,5 mm (1.160x.846)
- flush mount : Ø 30 mm (1.378)
• 1, 2, 3 and 4 poles
• Current/voltage rating : 12A 380VAC
16A 250VAC max. - 25mA 5VAC min.
• Solder lug/quick-connect terminals
• 1 and 2 poles
• Screw terminals (optional : quick-connect term.)
• Contacts : silver
These values are applicable for all components, accessories
and lamps, unless otherwise specified in the following pages.
• Contacts : silver, gold plated
• Current/voltage rating :
6A 250VAC max. - 10mA 5VAC min.
These values are applicable for all components, accessories
and lamps, unless otherwise specified in the following pages.
• Lamp : filament, neon or LED
• Lamp : filament, neon, LED
or special multi-LED array
Option : end cap terminal guard. Order separately (see
end of A02 series).
Packaging unit :
A1 : 25 pieces - A01 : 20 pieces (except pushbuttons: 25 pieces) - A02 : 25 pieces - A03 : 10 pieces.
Dimensions : first dimensions are in mm while inches are shown as bracketed numbers.
The company reserves the right to change specifications without notice.
G-2
www.apem.com
APEM
A1-A01-A02-A03 series
Industrial controls
Specifications for pushbutton, keylock and rotary switches
ELECTRICAL SPECIFICATIONS
A01 - A1 - A03
A02
Momentary
or maintained action
Momentary
or maintained action
10mA 5VAC min.
6A 250VAC max. - 6A 12VDC max.
25mA 5VAC min.
12A 380VAC - 16A 250VAC max.
12A 12VDC max.
> 1 mm (.039)
Double break 2 x 1,5 mm (.059)
10mΩ max. at 1A 4VDC
10mΩ max. at 1A 4VDC
50 MΩ min.
50 MΩ min.
750V between open contacts
5KV live to accessible
2KV between open contacts
4KV live to accessible
50.000 cycles
50.000 cycles
• Insulation :
Class 2
Class 2
• Lamp life :
LED : 60.000 h min. to 75% relative
luminosity - Filament : approx. 5.000 h
Neon : approx. 10.000 h
LED : 60.000 h min. to 75 % relative
luminosity - Filament : approx. 5.000 h
Neon : approx. 10.000 h
• Function :
• Current/voltage rating :
• Contact gap
• Initial contact resistance :
• Insulation resistance :
• Dielectric strength :
• Electrical life (resistive load) :
A
• Lamp circuit diagrams
B
A
B
GENERAL SPECIFICATIONS
A01 - A1 - A03
• Min. mechanical life :
A02
Pushb. momentary : 1 million cycles
Pushb. maintained : 100.000 cycles
Keylock and rotary : 100.000 cycles
Pushb. momentary: 1 million cycles
Pushb. maintained : 100.000 cycles
Keylock and rotary : 100.000 cycles
8 mm (.315) max.
8 mm (.315) max.
• Operating temperature :
-20°C to +55°C
-20°C to +85°C
• Solder heat resistance :
(IEC 68-2-20Tb, method 2)
350°C, 5 sec.
350°C, 5 sec.
• Degree of environmental
protection (IEC 529 )
IP 65 front of panel
IP 40 back of panel
IP 65 front of panel
IP 40 back of panel
Midget Grooved T13/4,
filament, LED or neon
Midget Grooved T13/4,
filament, LED or neon
Special multi-LED array
• Switch terminals :
Solder/quick-connect 2,8 mm (.110)
M3 screws - wire 2 x 0,75 mm2 max.
• Lamp terminals :
Solder/quick-connect 2,8 mm (.110)
M3 screws
Flexible wire 2 x 2,5 mm2 max.
Rigid wire 4 mm2 max.
• Panel thickness
• Lamps :
G
For screen engraving or film legends, contact APEM.
APEM
www.apem.com
G-3
A1 series
Engraved aluminium flush mounting pushbuttons and indicators
Panel cut-out Ø 22 (.866)
A pushbutton assembly requires :
engraved screen + lamp (if illuminated) + operator + switch block + flush mount bezel.
To order these elements, select desired model numbers from the table below.
Example : pushbutton, round, illuminated, sealed to IP65, latching, single pole with “start”
engraving, 24V blue LED and flush mounting bezel = A1PCA1X103K403.
1
3
2
18.00
(.709)
8.5
(.335)
14.5
(.571)
42.05
(1.655)
12.00
(.472)
Ø25.00
(9.85 DIA)
2.8
(.110)
18.00
(.709)
15.3
(.602)
7.65
(.301)
0.5
(.020)
A1
Accessories
03 - flushmount
Switch Type
Bezel
Illumination
Sealing
Function
Switch block
P - pushbutton
I - indicator
C - round
A - illuminated
B - non-illum.
0 - unsealed
1 - sealed IP65
0 - indicator
X - latching
Y - momentary
0 - indicator
1 - single pole
2 - double pole
5 - three pole
3 - four pole
Engraved Screen Options
G
OTHER SCREEN ENGRAVING OPTIONS :
contact APEM.
G-4
01 - Front Fog Lights
11 - ‘Lock’
02 - Rear Fog Lights
12 - ‘Unlock’
03 - ‘Start’
13 - Rear Window Heating
04 - Interior Light
14 - Cooling
05 - Boot Release
15 - Wipers
06 - Hazard Warning
16 - Washers
07 - Lights
17 - Fan
08 - Heating & Ventilation
18 - Horn
09 - Map Lights
19 - Air recirculation
10 - Side Lights
20 - Blank
www.apem.com
Bulb
A1 - filament 6.3V
B1 - filament 14V
C1 - filament 28V
D1 - filament 36V
E1 - filament 48V
F1 - filament 60V
G1 - Neon 110V
H1 - Neon 220V
I1 - Led 6V red
I2 - Led 6V green
I3 - Led 6V amber
J1 - Led 12V red
J2 - Led 12V green
J3 - Led 12V amber
J4 - Led 12V blue
J5 - Led 12V white
K1 - Led 24V red
K2 - Led 24V green
K3 - Led 24V amber
K4 - Led 24V blue
K5 - Led 24V white
L1 - Led 48V red
L2 - Led 48V green
L3 - Led 48V amber
APEM
A01 series
Illuminated or non-illuminated pushbutton switches
Panel cut-out Ø 16 (.630)
A pushbutton assembly requires :
screen + lamp (if illuminated) + operator + switch block.
To order these elements, select desired model numbers from tables below.
Example : IP65 rectangular pushbutton, single pole, maintained, red screen and 12V red LED =
A0161B, A0142M1, A0101X and A0151B.
3
3
3
2
2
9.00
(.354)
2
2
2
1
1
8.50
(.335)
1
3
3
3
24.00
(.945)
6.00
(.236)
❷
❶
Screen
Bezel
0.50
(.020)
D
2.80
(.110)
Operator
Lamp
Voltage
Part No
Pole
black
red
amber
yellow
green
blue
clear
white
black
red
amber
yellow
green
blue
clear
white
black
red
amber
yellow
green
blue
clear
white
A0161A
A0161B
A0161C
A0161D
A0161E
A0161F
A0161G
A0161J
A0162A
A0162B
A0162C
A0162D
A0162E
A0162F
A0162G
A0162J
A0163A
A0163B
A0163C
A0163D
A0163E
A0163F
A0163G
A0163J
Filament
Filament
Filament
Filament
Filament
Filament
Neon
Neon
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
6.3V
14V
28V
36V
48V
60V
110V
220V
6V red
6V green
6V amber
12V red
12V green
12V amber
12V blue
12V white
24V red
24V green
24V amber
24V blue
24V white
48V red
48V green
48V amber
A0141A
A0141B
A0141C
A0141D
A0141E
A0141F
A0143G
A0143H
A0142L1
A0142L2
A0142L3
A0142M1
A0142M2
A0142M3
A0142M4
A0142M5
A0142N1
A0142N2
A0142N3
A0142N4
A0142N5
A0142P1
A0142P2
A0142P3
1 or 2
1 or 2
1 or 2
1 or 2
3 or 4
3 or 4
3 or 4
3 or 4
1 or 2
1 or 2
1 or 2
1 or 2
3 or 4
3 or 4
3 or 4
3 or 4
1 or 2
1 or 2
1 or 2
1 or 2
3 or 4
3 or 4
3 or 4
3 or 4
E
F
❹
Lamp
Part No
D
30.70
(1.209)
18.00
(.709)
❸
Colour
C
Ø18.00
(.709 DIA)
18.00
(.709)
C
28.50
(1.122)
8.40
(.330)
42.00
(1.654)
18.00x18.00
(.709 SQ)
10.00
(.394)
7.65
(.301)
1
2
7.65 7.65
(.301) (.301)
18.00
(.709)
1
1
18.00
(.709)
6.00
(.236)
12.00
(.472)
6.00
(.236)
2
24.00
(.945)
16.25
(.640)
9.00
(.354)
3
1
Bezel
Switch block
Description
Part No
No of poles
Part No
Illum, momentary
Illum, maintained
Non-illum, momentary
Non-illum, maintained
Illum, momentary
Illum, maintained
Non-illum, momentary
Non-illum, maintained
Illum, momentary
Illum, maintained
Non-illum, momentary
Non-illum, maintained
Illum, momentary
Illum, maintained
Non-illum, momentary
Non-illum, maintained
Illum, momentary
Illum, maintained
Non-illum, momentary
Non-illum, maintained
Illum, momentary
Illum, maintained
Non-illum, momentary
Non-illum, maintained
A0101Y
A0101X
A0102Y
A0102X
A0103Y
A0103X
A0104Y
A0104X
A0105Y
A0105X
A0106Y
A0106X
A0107Y
A0107X
A0108Y
A0108X
A0109Y
A0109X
A0110Y
A0110X
A0111Y
A0111X
A0112Y
A0112X
Single pole
Double pole
Three pole
Four pole
A0151B
A0152B
A0155B
A0153B
UNSEALED SWITCHES (IP40) :
add “01” to end of operator
model number.
BI-COLOUR LED’s optional.
SCREEN ENGRAVING/INSERTABLE LEGENDS : contact APEM
Bezel:
APEM
rectangular,
square,
round,
‘Illum’ - illuminated,
‘Non-illum’ - non illuminated
www.apem.com
G-5
G
A01 series
Indicators
Panel cut-out Ø 16 (.630)
An indicator assembly requires :
screen + lamp + operator.
To order these elements, select desired model numbers from tables below.
Example : IP65 rectangular indicator with red screen and 12V red LED = A0161B, A0142M1 and A0171.
24.00
(.945)
Ø18.00
(.709 DIA)
8.40
(.330)
42.00
(1.654)
10.00
(.394)
18.00
(.709)
18.00
(.709)
8.50
(.335)
❷
❶
Screen
Bezel
G
0.50
(.020)
2.80
(.110)
❸
Operator
Lamp
Colour
Part No
Lamp
Voltage
Part No
black
red
amber
yellow
green
blue
clear
white
black
red
amber
yellow
green
blue
clear
white
black
red
amber
yellow
green
blue
clear
white
A0161A
A0161B
A0161C
A0161D
A0161E
A0161F
A0161G
A0161J
A0162A
A0162B
A0162C
A0162D
A0162E
A0162F
A0162G
A0162J
A0163A
A0163B
A0163C
A0163D
A0163E
A0163F
A0163G
A0163J
Filament
Filament
Filament
Filament
Filament
Filament
Neon
Neon
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
6.3V
14V
28V
36V
48V
60V
110V
220V
6V red
6V green
6V amber
12V red
12V green
12V amber
12V blue
12V white
24V red
24V green
24V amber
24V blue
24V white
48V red
48V green
48V amber
A0141A
A0141B
A0141C
A0141D
A0141E
A0141F
A0143G
A0143H
A0142L1
A0142L2
A0142L3
A0142M1
A0142M2
A0142M3
A0142M4
A0142M5
A0142N1
A0142N2
A0142N3
A0142N4
A0142N5
A0142P1
A0142P2
A0142P3
Bezel
Description
Part No
Indicator
Indicator
Indicator
A0171
A0172
A0173
UNSEALED INDICATORS (IP40) :
add “01” to end of operator model
number.
SCREEN ENGRAVING / INSERTABLE LEGENDS : contact APEM
Bezel:
G-6
rectangular,
square,
round
www.apem.com
APEM
A01 series
Rotary lever switches
Panel cut-out Ø 16 (.630)
A rotary lever switch assembly requires :
operator + switch block.
To order these elements, select desired model numbers from tables below.
Example : IP65 rectangular rotary switch with long lever, clockwise rotation, single pole,
2 positions, maintained = A019109 and A0151B.
12.00
(.472)
2
24.00
(.945)
6.00
(.236)
1
3
3
1
3
3
2
2
2
1
2
2
1
3
3
1
7.65
(.301)
1
1
3
8.40
(.330)
C
D
28.50
(1.122)
10.00
(.394)
42.00
(1.654)
0.50
(.020)
18.00
(.709)
2.80
(.110)
18.00
(.709)
❷
❶
18.00
(.709)
2
24.00
(.945)
C
D
18.00x18.00
(.709 SQ)
E
Ø18.00
(.709 DIA)
F
30.70
(1.209)
Lever Positions
B
C
A
Operator
Pole
Bezel Description
1 or 2
1 or 2
3 or 4
3 or 4
1 or 2
1 or 2
1 or 2
1 or 2
1 or 2
1 or 2
3 or 4
3 or 4
1 or 2
1 or 2
1 or 2
1 or 2
1 or 2
1 or 2
3 or 4
3 or 4
1 or 2
1 or 2
1 or 2
1 or 2
Bezel:
APEM
2 pos. maintained
2 pos. momentary
2 pos. maintained
2 pos. momentary
3 pos. maintained
3 pos. momentary
3 pos. mainL, momR
3 pos. momL, mainR
2 pos. maintained
2 pos. momentary
2 pos. maintained
2 pos. momentary
3 pos. maintained
3 pos. momentary
3 pos. mainL, momR
3 pos. momL, mainR
2 pos. maintained
2 pos. momentary
2 pos. maintained
2 pos. momentary
3 pos. maintained
3 pos. momentary
3 pos. mainL, momR
3 pos. momL, mainR
rectangular,
Switch block
Short lever Long lever
No of poles
Part No
A019209
A019210
A019211
A019212
A019205
A019206
A019207
A019208
A019409
A019410
A019411
A019412
A019405
A019406
A019407
A019408
A019609
A019610
A019611
A019612
A019605
A019606
A019607
A019608
Single pole
Double pole
Three pole
Four pole
A0151B
A0152B
A0155B
A0153B
square,
A019109•
A019110•
A019111•
A019112•
A019105
A019106
A019107
A019108
A019309•
A019310•
A019311•
A019312•
A019305
A019306
A019307
A019308
A019509•
A019510•
A019511•
A019512•
A019505
A019506
A019507
A019508
round,
• Lever Rotation - 2 position switches
The model numbers shown are for switches
with clockwise lever rotation.
For anticlockwise rotation, replace :
G
09
with
01
10
with
02
11
with
03
12
with
04
at the end of the model number.
Optional Engraving on
Lever end
See above photo left.
To order, add “WL” to the end of the operator
part No.
Example : A019609WL..
‘pos’ - position,
‘mainL’ - maintained left,
‘momR’ - momentary right, etc
www.apem.com
G-7
A01 series
Keylock switches
Panel cut-out Ø 16 (.630)
A keylock switch assembly requires :
operator + switch block.
To order these elements, select desired model numbers from tables below.
Example : IP65 rectangular keyswitch, clockwise rotation, single pole, 2 positions, maintained
= A018125 and A0151B.
3
1
2
24.00
(.945)
1
3
12.00
(.472)
1
3
3
1
18.00x18.00
(.709 SQ)
1
3
7.65
(.301)
2
18.00
(.709)
2
6.00
(.236)
2
2
38.00
(1.496)
2
2
1
1
3
3
24.00
(.945)
18.00
(.709)
C
❷
❶
D
18.00
(.709)
2.80
(.110)
28.50
(1.122)
0.50
(.020)
8.40
(.330)
42.00
(1.654)
Ø18.00
(.709 DIA)
C
D
E
F
30.70
(1.209)
Key Positions
B
Operator
Pole
G
1 or 2
1 or 2
1 or 2
3 or 4
3 or 4
1 or 2
1 or 2
1 or 2
1 or 2
1 or 2
1 or 2
1 or 2
3 or 4
3 or 4
1 or 2
1 or 2
1 or 2
1 or 2
1 or 2
1 or 2
1 or 2
3 or 4
3 or 4
1 or 2
1 or 2
1 or 2
1 or 2
Bezel:
G-8
Bezel Description
2 pos. maintained
2 pos. maintained
2 pos. momentary
2 pos. maintained
2 pos. momentary
3 pos. maintained
3 pos. momentary
3 pos. mainL, momR
3 pos. momL, mainR
2 pos. maintained
2 pos. maintained
2 pos. momentary
2 pos. maintained
2 pos. momentary
3 pos. maintained
3 pos. momentary
3 pos. mainL, momR
3 pos. momL, mainR
2 pos. maintained
2 pos. maintained
2 pos. momentary
2 pos. maintained
2 pos. momentary
3 pos. maintained
3 pos. momentary
3 pos. mainL, momR
3 pos. momL, mainR
rectangular,
A018123
A018125•
A018124•
A018127•
A018128•
A018105
A018106
A018107
A018108
A018223
A018225•
A018224•
A018227•
A018228•
A018205
A018206
A018207
A018208
A018323
A018325•
A018324•
A018327•
A018328•
A018305
A018306
A018307
A018308
square,
A
Switch block
Part No Key removable
A
A-B
A
A-B
A
A-B-C
A
A-B
A-C
A
A-B
A
A-B
A
A-B-C
A
A-B
A-C
A
A-B
A
A-B
A
A-B-C
A
A-B
A-C
round,
No of poles
Part No
Single pole
Double pole
Three pole
Four pole
A0151B
A0152B
A0155B
A0153B
C
• Key Rotation - 2 position switches
The model numbers shown are for switches
with clockwise key rotation.
For anticlockwise rotation, replace :
25
24
27
28
with
with
with
with
01
02
03
04
at the end of the model number.
2 standard keys are supplied.
20 key barrel types available.
NON-REMOVABLE KEY POSITIONS / ON-ON-ON FUNCTION : contact APEM.
‘pos’ - position,
‘mainL’ - maintained left,
www.apem.com
‘momR’ - momentary right, etc
APEM
A01 series
Mushroom head pushbutton switches
Panel cut-out Ø 16 (.630)
• Prominent 24 mm (.944) dia. or optional 40 mm (1.575) dia. mushroom actuators
• Momentary and maintained functions
Momentary function versions are unmarked.
Maintained function versions are twist release (arrows indicate direction of twist)
• Various coloured mushroom actuators are available.
2
0.50
(.020)
C
D
2.80
(.110)
Ø40.00
(1.575 DIA)
8.40
(.330)
42.00
(1.654)
OPTION : SP3
VERSION
Option
: SP3
version
18.00
(.709)
18.00
(.709)
❷
❶
Operator
Switch block
Actuator
Description
Part No
No of poles
Part No
24mmØ
24mmØ
24mmØ
24mmØ
24mmØ
24mmØ
24mmØ
24mmØ
24mmØ
24mmØ
40mmØ
40mmØ
40mmØ
40mmØ
40mmØ
40mmØ
40mmØ
40mmØ
40mmØ
40mmØ
Black momentary
Red momentary
Yellow momentary
Green momentary
Blue momentary
Black maintained
Red maintained
Yellow maintained
Green maintained
Blue maintained
Black momentary
Red momentary
Yellow momentary
Green momentary
Blue momentary
Black maintained
Red maintained
Yellow maintained
Green maintained
Blue maintained
A01MMA
A01MMB
A01MMD
A01MME
A01MMF
A01MXA
A01MXB
A01MXD
A01MXE
A01MXF
A01MMA SP3
A01MMB SP3
A01MMD SP3
A01MME SP3
A01MMF SP3
A01MXA SP3
A01MXB SP3
A01MXD SP3
A01MXE SP3
A01MXF SP3
Single pole
Double pole
Three pole
Four pole
A0151B
A0152B
A0155B
A0153B
APEM
3
Ø24.00
(.945DIA)
19.00
(1.047)
1
www.apem.com
G
G-9
A1-A01 series
Industrial controls
Accessories
Ø25.00
(.984 DIA)
Ø16.00
(.630DIA)
11.00
(.433)
+0.20
20.60 0.00
+.008
(.811 .000)
18.15
(.715)
Ø16.00
(.630DIA)
23.80
(.937)
23.80
(.937)
12.00
(.472)
Ø22.00
(.866 DIA)
29.80
(1.173)
12.00
(.472)
20.40
(.803)
18.10
(.712)
20.40
(.803)
23.80
(.937)
Ø16.00
(.630DIA)
Dark grey plastic material - supplied with sealing washer
18.10
(.712)
FLUSH MOUNTING BEZELS
+0.20
26.70 0.00
(1.051 +.008
.000 )
Rectangular A01FM1
Square A01FM
(.874
Round A01FM2
Ø25.00
(.984 DIA)
Ø22.00
(.866 DIA)
Ø16.00
(.630DIA)
Metal versions
18.15
(.715)
FLUSH MOUNTING BEZELS
+0.20
22.20 0.00
+.008
.000 )
+0.20
20.60 0.00
(.811 +.008
.000 )
11.00
(.433)
+0.20
22.20 0.00
+.008
.000 )
(.874
Round, anodised aluminium A01FMM
Round, matt black A01FMMG
PCB SOCKET
18.40
(.724)
6.00
(.236)
G
Single pole, non illuminated
Double pole, non illuminated
Single pole, illuminated
Double pole, illuminated
Indicator
Single pole, E-stop
Double pole, E-stop
7.65
(.301)
0.80
(.031)
6.00
(.236)
7.65
(.301)
18.25
(.719)
5.00
(.196)
10.25
(.403)
4.25
(.167)
1.10
(.043)
4.25
(.167)
A01PC1
A01PC2
A01PC3
A01PC4
A01PC5
A01PC6
A01PC7
Rectangular A01FG1
G-10
www.apem.com
13.50
(.531)
18.00
(.708)
24.00
(.945)
13.65
(.537)
13.65
(.537)
9.00
(.354)
24.00
(.945)
12.00
(.472)
24.00
(.945)
13.50
(.531)
FLAPGUARDS
Square/round A01FG2
APEM
A1-A01 series
Industrial controls
Accessories
METAL GUARDS
➞ Slot as alternative to Ø 2 mm hole - Material : 1 mm thick aluminium.
Ø16.00
(.630DIA)
Ø16.00
(.630DIA)
Rectangular A01MG1
Ø16.05
(.631DIA)
Round, natural A01MG2
Matt black A01MG2G
Square A01MG
Recommended to prevent product rotation
Ø16.00
(.629DIA)
18.00
(.708)
14.75
(.580)
ANTI ROTATION RING
12.00
(.472)
18.20
(.717)
24.00
(.944)
10.15
(.399)
18.00
(.708)
9.80
(.385)
12.00
(.472)
Ø19.60
(.771 DIA)
18.00
(.708)
Ø2.00
(.078DIA)
8.90
(.350)
Ø18.10
(.712 DIA)
A01LW
18.00
(.708)
2.00
(.078)
SWITCHBLOCK TERMINAL GUARDS
14.85
(.584)
2 way A01RTC2
BLANKING PLUGS
24.0
(.946)
18.0
(.709)
18.0
(.709)
RESISTOR ASSEMBLY
20.75
(.816)
8 way A01RTC8
Ø18.0
(.709 DIA)
Round A0133
8.50
(.334)
10.50 10.00
(.413) (.393)
Square A0132
18.0
(.709)
10.50 10.00
(.413) (.393)
20.75
(.816)
20.75
(.816)
7.35
(.289)
6.00
(.236)
7.45
(.293)
Rectangular A0131
G
Resistor assembly - 2 stage illumination
A0152B + RISSP
(DIM) normally closed
APEM
www.apem.com
(BRIGHT) normally open
G-11
A1-A01 series
Industrial controls
Installation - tools
Modular construction / panel mounting
PUSHBUTTONS
& INDICATORS
EMERGENCY
STOP
ROTARY
LEVER SWITCHES
PANEL CUT-OUT
SCREEN
Round & square operators only
Ø16.00 0.00/+0.30
(.629 DIA .000/+.011 ))
LEGEND
KEYLOCK
SWITCHES
REFLECTOR
POLARISING
DOT
FIXING
NUT
4.00 Maxi
(.157 MAX)
PANEL
SEAL
OPERATOR
77.25
((.285)
LOCATING
SLOT
BULB
1.50
1
(.059)
Rectangular operators only
Ø16.00 0.00/+0.30
(.629 DIA .000/+.011))
Ø2.00
(.078 DIA)
LATCH
SWITCH BLOCK
10.50
((.413)
Max. panel thickness : 8 mm (.315)
PANEL MOUNTING ASSEMBLY
TO REMOVE BULB
• Drill/punch hole shaped as above.
Remove reflector/screen assembly. Use the bulb extractor
30-0002 to remove the bulb.
• Assemble front operator through hole, fit fixing nut and
tighten to a maximum torque of 0,8Nm using tool
No 30-0001.
SWITCH BLOCK
• Wire chosen switch block as required and slide onto
operator until latch engages.
To assemble switch block to front operator, TAKE CARE
TO LINE UP SWITCH BLOCK WITH FRONT OPERATOR.
Once in position, slide on to front operator. NB. : Ensure
latch is fully engaged correctly onto the switch block.
• Fit bulb if required using tool No 30-0002.
G
• Snap screen onto reflector assembly with legend in
between if required and snap onto front operator TAKING
CARE TO LINE UP THE LOCATING SLOT WITH THE
POLARISING DOT, and not to damage the seal.
G-12
To remove switch block, depress the latch and slide the
switch block off the operator.
FIXING NUT KEY
BULB REMOVER
30-0001
30-0002
www.apem.com
APEM
A02 series
Illuminated or non-illuminated pushbutton switches
Panel cut-out Ø 22 (.866) or 29,5 x 21,5 (1.160x.846)
A pushbutton assembly requires :
UG1410A-R1
screen + lamp (if illuminated) + operator + one or two switch blocks.
To order these elements, select desired model numbers from tables below.
Example : IP65 illuminated rectangular maintained pushbutton, switch block with 2 N.O. contacts,
red screen and 12V red LED = A0261B, A0142M1, A0201X and A02503.
N.C.
N.O.
N.O./N.C.
10.00
(.394)
10.00
(.394)
10.00
(.394)
24.00
(.945)
29.00
(1.142)
36.00
(1.417)
21.00
(.827)
Ø29.00
(1.142 DIA)
21.00
(.827)
27.00
(1.062)
33.50
(1.319)
64.00
(2.520)
64.00
(2.520)
55.50
(2.185)
29.00x29.00
(1.142 SQ)
33.50
(1.319)
❷
❶
Screen
Bezel
❸
Lamp
❹
Operator
Colour
Part No
Lamp
Voltage
Part No
black
red
amber
yellow
green
blue
clear
white
black
red
amber
yellow
green
blue
clear
white
black
red
amber
yellow
green
blue
clear
white
A0261A
A0261B
A0261C
A0261D
A0261E
A0261F
A0261G
A0261J
A0262A
A0262B
A0262C
A0262D
A0262E
A0262F
A0262G
A0262J
A0263A
A0263B
A0263C
A0263D
A0263E
A0263F
A0263G
A0263J
Filament
Filament
Filament
Filament
Filament
Filament
Neon
Neon
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
6.3V
14V
28V
36V
48V
60V
110V
220V
6V red
6V green
6V amber
12V red
12V green
12V amber
12V blue
12V white
24V red
24V green
24V amber
24V blue
24V white
48V red
48V green
48V amber
A0141A
A0141B
A0141C
A0141D
A0141E
A0141F
A0143G
A0143H
A0142L1
A0142L2
A0142L3
A0142M1
A0142M2
A0142M3
A0142M4
A0142M5
A0142N1
A0142N2
A0142N3
A0142N4
A0142N5
A0142P1
A0142P2
A0142P3
Bezel
Switch block
Description
Lamp type
Part No
Contacts
Part No
Illum, momentary
Illum, maintained
Non-illum, maintained
Non-illum, momentary
Illum, momentary
Illum, maintained
Non-illum, momentary
Non-illum, maintained
Illum, momentary
Illum, maintained
Non-illum, momentary
Non-Illum, maintained
Lamp/LED
Lamp/LED
A0201Y
A0201X
A0203X
A0203Y
A0204Y
A0204X
A0206Y
A0206X
A0207Y
A0207X
A0209Y
A0209X
1 N.O.
1 N.C.
2 N.O.
2 N.C.
1 N.O./1 N.C.
A02501
A02502
A02503
A02504
A02505
Lamp/LED
Lamp/LED
Lamp/LED
Lamp/LED
UNSEALED SWITCHES (IP40) :
add “01” to end of operator model number.
Second switch block
Contacts
Part No
1 N.O.
1 N.C.
2 N.O.
2 N.C.
1 N.O./1 N.C.
A02506
A02507
A02508
A02509
A02510
To achieve 3 or 4 pole switching,
add second switch block, from
above table.
SCREEN ENGRAVING / INSERTABLE LEGENDS : contact APEM.
Bezel:
rectangular,
square,
round,
‘Illum’ - illuminated,
‘Non-illum’ - non illuminated
The company reserves the right to change specifications without notice.
APEM
www.apem.com
G-15
G
A02 series
Metal bezel pushbutton switches and indicators
Panel cut-out Ø 22 (.866)
A pushbutton assembly requires :
screen + lamp (if illuminated) + operator + one or two switch blocks.
An indicator assembly requires : screen + lamp + operator
To order these elements, select desired model numbers from tables below.
Example : IP65 illuminated metal bezel maintained pushbutton, switch block with 2 N.O. contacts,
red screen and 12V red LED = A0263B, A0142M1, A0211X and A02503.
N.O.
N.C.
N.O./N.C.
45.50
(1.791)
11.50
(.452)
Ø29.00
(1.142DIA)
75.00
(2.952)
Ø29.00
(1.142DIA)
34.00
(1.338)
❷
❶
Screen
Bezel
G
21.00
(.826)
❸
❹
Lamp
Operator
Colour
Part No
Lamp
Voltage
Part No
black
red
amber
yellow
green
blue
clear
white
A0263A
A0263B
A0263C
A0263D
A0263E
A0263F
A0263G
A0263J
Filament
Filament
Filament
Filament
Filament
Filament
Neon
Neon
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
6.3V
14V
28V
36V
48V
60V
110V
220V
6V red
6V green
6V amber
12V red
12V green
12V amber
12V blue
12V white
24V red
24V green
24V amber
24V blue
24V white
48V red
48V green
48V amber
A0141A
A0141B
A0141C
A0141D
A0141E
A0141F
A0143G
A0143H
A0142L1
A0142L2
A0142L3
A0142M1
A0142M2
A0142M3
A0142M4
A0142M5
A0142N1
A0142N2
A0142N3
A0142N4
A0142N5
A0142P1
A0142P2
A0142P3
Bezel
Description
Lamp type
Illum, momentary
Lamp/LED
Illum, maintained
Lamp/LED
Non-illum, momentary
Non-illum, maintained
Illum, indicator
Lamp/LED
Switch block
Part No
Contacts
Part No
A0210Y
A0210X
A0212Y
A0212X
A0277
1 N.O.
1 N.C.
2 N.O.
2 N.C.
1 N.O./1 N.C.
A02501
A02502
A02503
A02504
A02505
Std bezel material : nickel plated brass.
For optional black finish, add “G” to the end of
operator model number.
UNSEALED SWITCHES (IP40) :
add “01” to end of operator model number.
Second switch block
Contacts
Part No
1 N.O.
1 N.C.
2 N.O.
2 N.C.
1 N.O./1 N.C.
A02506
A02507
A02508
A02509
A02510
To achieve 3 or 4 pole switching,
add second switch block, from
above table.
SCREEN ENGRAVING / INSERTABLE LEGENDS : contact APEM.
Bezel:
G-16
rectangular,
square,
round,
‘Illum’ - illuminated,
‘Non-illum’ - non illuminated
www.apem.com
APEM
A02 series
Flush mounting pushbutton switches and indicators
Panel cut-out Ø 30 (1.181)
A pushbutton assembly requires :
screen + lamp (if illuminated) + operator + one or two switch blocks.
An indicator assembly requires : screen + lamp + operator
To order these elements, select desired model numbers from tables below.
Example : IP65 illum. flush mounting maintained pushbutton, switch block with 2 N.O. contacts,
red screen and 12V red LED = A0263B, A0142M1, A0213X and A02503.
N.O.
N.O./N.C.
Ø35.00
(1.378DIA)
73.00
(2.874)
46.00
(1.811)
2.00
(.078)
Ø35.00
(1.378DIA)
N.C.
PANEL CUT-OUT
DU PANNEAU
DECOUPE
34.00
(1.338)
❷
❶
Screen
Bezel
21.00
(.826)
❸
Lamp
❹
Operator
Colour
Part No
Lamp
Voltage
Part No
black
red
amber
yellow
green
blue
clear
white
A0263A
A0263B
A0263C
A0263D
A0263E
A0263F
A0263G
A0263J
Filament
Filament
Filament
Filament
Filament
Filament
Neon
Neon
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
6.3V
14V
28V
36V
48V
60V
110V
220V
6V red
6V green
6V amber
12V red
12V green
12V amber
12V blue
12V white
24V red
24V green
24V amber
24V blue
24V white
48V red
48V green
48V amber
A0141A
A0141B
A0141C
A0141D
A0141E
A0141F
A0143G
A0143H
A0142L1
A0142L2
A0142L3
A0142M1
A0142M2
A0142M3
A0142M4
A0142M5
A0142N1
A0142N2
A0142N3
A0142N4
A0142N5
A0142P1
A0142P2
A0142P3
Bezel
30.00
(1.181)
Description
Lamp type
Illum, momentary
Lamp/LED
Illum, maintained
Lamp/LED
Non-illum, momentary
Non-illum, maintained
Illum, indicator
Lamp/LED
Switch block
Part No
Contacts
Part No
A0214Y
A0214X
A0215Y
A0215X
A02791
1 N.O.
1 N.C.
2 N.O.
2 N.C.
1 N.O./1 N.C.
A02501
A02502
A02503
A02504
A02505
Std bezel material : silver anodised aluminium.
For optional black anodised aluminium, add “G”
to end of operator model number.
UNSEALED SWITCHES (IP40) :
add “01” to end of operator model number.
Second switch block
Contacts
Part No
1 N.O.
1 N.C.
2 N.O.
2 N.C.
1 N.O./1 N.C.
A02506
A02507
A02508
A02509
A02510
To achieve 3 or 4 pole switching,
add second switch block, from
above table.
SCREEN ENGRAVING / INSERTABLE LEGENDS : contact APEM.
Bezel:
APEM
rectangular,
square,
round,
‘Illum’ - illuminated,
‘Non-illum’ - non illuminated
www.apem.com
G-17
G
A02 series
Indicators
Panel cut-out Ø 22 (.866) or 29,5 x 21,5 (1.160x.846)
10.00
(.394)
An indicator assembly requires :
Screen + lamp, LED or LED assembly + operator.
To order these elements, select desired model numbers from tables below.
Example : IP65 rectangular indicator with red screen and 12V red LED = A0261B, A0142M1 and A0272.
24.00
(.945)
29.00
(1.142)
36.00
(1.417)
21.00
(.827)
29.00x29.00
(1.142 SQ)
10.00
(.394)
29.00
(1.142)
33.50
(1.319)
37.50
(1.476)
Ø29.00
(1.142 DIA)
33.50
(1.319)
❷
❶
Screen
Bezel
G
21.00
(.827)
❸
Lamp
Operator
Colour
Part No
Lamp
Voltage
Part No
black
red
amber
yellow
green
blue
clear
white
black
red
amber
yellow
green
blue
clear
white
black
red
amber
yellow
green
blue
clear
white
A0261A
A0261B
A0261C
A0261D
A0261E
A0261F
A0261G
A0261J
A0262A
A0262B
A0262C
A0262D
A0262E
A0262F
A0262G
A0262J
A0263A
A0263B
A0263C
A0263D
A0263E
A0263F
A0263G
A0263J
Filament
Filament
Filament
Filament
Filament
Filament
Neon
Neon
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
6.3V
14V
28V
36V
48V
60V
110V
220V
6V red
6V green
6V amber
12V red
12V green
12V amber
12V blue
12V white
24V red
24V green
24V amber
24V blue
24V white
48V red
48V green
48V amber
A0141A
A0141B
A0141C
A0141D
A0141E
A0141F
A0143G
A0143H
A0142L1
A0142L2
A0142L3
A0142M1
A0142M2
A0142M3
A0142M4
A0142M5
A0142N1
A0142N2
A0142N3
A0142N4
A0142N5
A0142P1
A0142P2
A0142P3
Bezel
Description
Lamp type
Part No
Indicator
Indicator
Indicator
Lamp/LED
Lamp/LED
Lamp/LED
A0271
A0273
A0275
UNSEALED INDICATORS (IP40) :
add “01” to end of operator model number.
SCREEN ENGRAVING / INSERTABLE LEGENDS : contact APEM.
Bezel:
G-18
rectangular,
square,
round,
www.apem.com
APEM
A02 series
Rotary switches
Panel cut-out Ø 22 (.866)
A rotary lever assembly requires :
operator + one or two switch blocks.
To order these elements, select desired model numbers from tables below.
Example : IP65 square 2 position maintained rotary switch with long lever, clockwise rotation,
switch block with 2 N.O. contacts = A029107 and A02503.
N.O./N.C.
N.C.
N.O.
29.00
(1.142)
20.00
(.787)
22.00
(.866)
29.00x29.00
(1.142 SQ)
21.00
(.827)
27.00
(1.062)
22.00
(.866)
64.00
(2.520)
64.00
(2.520)
Ø29.00
(1.142 DIA)
33.50
(1.319)
❷
❶
Lever positions
B
Operator
Bezel
Switch block
Description
Short lever
Long lever
Contacts
Part No
2 pos. maintained
2 pos. momentary
3 pos. maintained
3 pos. momentary
3 pos. mainL, momR
3 pos. momL, mainR
2 pos. maintained
2 pos. momentary
3 pos. maintained
3 pos. momentary
3 pos. mainL, momR
3 pos. momL, mainR
A029207
A029208
A029203
A029204
A029205
A029206
A029407
A029408
A029403
A029404
A029405
A029406
A029107•
A029108•
A029103
A029104
A029105
A029106
A029307•
A029308•
A029303
A029304
A029305
A029306
1 N.O.
1 N.C.
2 N.O.
2 N.C.
1 N.O./1 N.C.
A02501
A02502
A02503
A02504
A02505
OPTION
To specify flush mounting (Ø 30 mm) option,
add “FM” to the end of the part number (for
round operators only).
Example : A029407FM.
Bezel:
APEM
square,
Second switch block
Contacts
Part No
1 N.O.
1 N.C.
2 N.O.
2 N.C.
1 N.O./1 N.C.
A02506
A02507
A02508
A02509
A02510
To achieve 3 or 4 pole switching,
add second switch block, from
above table.
C
A
• Lever Rotation - 2 position switches
The model numbers shown are for switches
with clockwise lever rotation.
For anticlockwise rotation, replace :
07
with
01
08
with
02
at the end of the model number.
G
Optional engraving
on lever end
To order, add “WL” to the end of the part No.
Example : A029407WL.
round,
www.apem.com
G-19
A02 series
Keylock switches
Panel cut-out Ø 22 or 29,5 x 21,5
A keyswitch assembly requires :
operator + one or two switch blocks.
To order these elements, select desired model numbers from tables below.
Example : IP65 square 2 position keyswitch, clockwise rotation, switch block with 2 N.O.
contacts = A028220 and A02503.
N.O./N.C.
N.C.
N.O.
29.00
(1.142)
29.00x29.00
(1.142 SQ)
64.00
(2.520)
55.50
(2.185)
38.00
(1.496)
34.50
(1.358)
24.00
(.945)
36.00
(1.417)
21.00
(.827)
21.00
(.827)
27.00
(1.062)
33.50
(1.319)
Ø29.00
(1.142 DIA)
33.50
(1.319)
❷
Key positions
C
B
Operator
Bezel
Description
2 pos. maintained
2 pos. momentary
3 pos. maintained
3 pos. momentary
3 pos. mainL, momR
3 pos. momL, mainR
2 pos. maintained
2 pos. momentary
3 pos. maintained
3 pos. momentary
3 pos. mainL, momR
3 pos. momL, mainR
2 pos. maintained
2 pos. momentary
3 pos. maintained
3 pos. momentary
3 pos. mainL, momR
3 pos. momL, mainR
G
Part No
Key removable
in positions
A028120•
A-B
A028119•
A
A028105
A-B-C
A028106
A
A028107
A-B
A028108
A-C
A028220•
A-B
A028219•
A
A028205
A-B-C
A028206
A
A028207
A-B
A028208
A-C
A028320•
A-B
A028319•
A
A028305
A-B-C
A028306
A
A028307
A-B
A028308
A-C
OPTION
To specify flush mounting (Ø 30 mm) option,
add “FM” to the end of the part number (for
round operators only). Example : A028320FM.
Bezel:
G-20
rectangular,
square,
A
Switch block
Contacts
Part No
• Key Rotation - 2 position switches
1 N.O.
1 N.C.
2 N.O.
2 N.C.
1 N.O./1 N.C.
A02501
A02502
A02503
A02504
A02505
The model numbers shown are for switches
with clockwise key rotation.
For anticlockwise rotation, replace:
Second switch block
Contacts
Part No
1 N.O.
1 N.C.
2 N.O.
2 N.C.
1 N.O./1 N.C.
A02506
A02507
A02508
A02509
A02510
20
19
with
with
01
02
at the end of the model number
• 2 standard keys are supplied.
• 20 key barrel types available.
Non-removable key positions : contact
APEM.
To achieve 3 or 4 pole switching,
add second switch block, from
above table
round,
www.apem.com
APEM
A02 series
Mushroom head pushbutton switches
Panel cut-out Ø 22 (.866)
• Prominent 40 mm (1.575) dia. mushroom actuator or optional 26 mm (1.024) actuator
• Momentary and maintained functions
Momentary function versions are unmarked
Maintained function versions are twist to release (arrows indicate direction of twist)
• Various coloured mushroom actuators are available
N.O.
N.C.
N.O./N.C.
29.00
(1.142)
64.00
(2.520)
21.00
(.827)
Ø40.00
(1.575 DIA)
21.00
(.827)
❷
❶
Operator
Bezel
Switch block
Description
Part No
Contacts
Part No
Black momentary
Red momentary
Yellow momentary
Green momentary
Blue momentary
Black maintained
Red maintained
Yellow maintained
Green maintained
Blue maintained
A02MMA
A02MMB
A02MMD
A02MME
A02MMF
A02MXA
A02MXB
A02MXD
A02MXE
A02MXF
1 N.O.
1 N.C.
2 N.O.
2 N.C.
1 N.O./1 N.C.
A02501
A02502
A02503
A02504
A02505
OPTION
For optional reduced (Ø 26 mm) mushroom
head operators : contact APEM.
G
Second switch block
Contacts
Part No
1 N.O.
1 N.C.
2 N.O.
2 N.C.
1 N.O./1 N.C.
A02506
A02507
A02508
A02509
A02510
To achieve 3 or 4 pole switching,
add second switch block, from
above table
Bezel:
APEM
round
www.apem.com
G-21
A02 series
Industrial controls
Installation
Modular construction / panel mounting
ROTARY
LEVERS SWITCHES
LEGEND
KEYLOCK
SWITCHES
REFLECTOR
LOCATING
SLOT
BULB
FIXING
NUT
6.00 Maxi
(.236 MAX)
POLARISING
DOT
PANEL
SEAL
OPERATOR
ADAPTOR BLOCK
SWITCH BLOCK
PANEL CUT-OUT
Round & square operators
Ø22.00 0.00/+0.50
(.866 DIA .000/+.019)
Ø22.00 0.00/+0.50
(.866 DIA .000/+.019)
13.00
(.511)
13.00
(.511)
Rectangular operators
0.00/+0.50
21.50
0.00/+0.50
21.50
.000/+.019
(.846(.846
) )
.000/+.019
EMERGENCY
STOP
SCREEN
3.003.00
(.118)
(.118)
PUSHBUTTONS & INDICATORS
29.50 0.00/+0.50
(1.161 .000/+.019 )
29.50 0.00/+0.50
(1.161 .000/+.019 )
END CAP
PANEL CLAMP
FIXING SCREW
Max. panel thickness : 8 mm (.315)
PANEL MOUNTING ASSEMBLY
TO REMOVE BULB
• Drill/punch hole in panel as shaped above.
Remove reflector/screen assembly. Use the bulb extractor
30-0002 to remove the bulb.
• Assemble front operator through hole and :
a/ Round & square types : tighten nut to a maximum
torque of 0,8Nm using tool No 30-0001. Snap on
adaptor block
b/ Rectangular types : tighten two panel fixing screws in
front to a maximum torque of 0,06Nm.
• Wire chosen switch block as required and snap onto
front operator.
TO REMOVE SWITCH BLOCK
Lever out latches using small screwdriver taking care not to
overbend, and pull off the block from the front operator.
A02 Accessories
• Snap end cap onto switch block.
• Fit bulb if required using tool No 30-0002.
G
• Snap screen onto reflector assembly with legend in
between if required ans snap into front operator TAKING
CARE TO LINE UP THE LOCATING SLOT WITH THE
POLARISING DOT, and not to damage the seal.
Part No : 14-0005
End cap terminal guard offering unique terminal protection.
6.35 mm push on tab terminals.
Specify “SP” to the end of the switchblock and operator P/N.
Example : A02503SP.
G-22
www.apem.com
APEM
A03 series
Illuminated or non-illuminated pushbutton switches and indicators
Panel cut-out Ø 22 (.866) or 30 (1.181) - Plastic or metal flush mounting bezel
A pushbutton assembly requires :
screen + lamp (if illuminated) + operator + switch block.
To order these elements, select desired model numbers from tables below.
Example : IP65 flush mounting round pushbutton, maintained function, red screen, 12V red LED
and single pole switch block = A0314X, A0263B, A0142M1 and A0151B.
2
1.0 to 6.0
Panel Thickness
59.50
(2.344)
59.00
(2.325)
26.00
(1.024)
10.00
(.394)
49.00
(1.931)
3
Ø35.00
(1.379 DIA)
2.00
(.079)
Ø29.00
(1.143 DIA)
1
0.50
6.00
(.236)
18.00
(.709)
6.00
(.236)
18.00
(.709)
❷
❶
❸
Screen
Bezel
Bezel:
APEM
❹
Lamp
Operator
Colour
Part No
Lamp
Voltage
Part No
black
red
amber
yellow
green
blue
clear
white
A0263A
A0263B
A0263C
A0263D
A0263E
A0263F
A0263G
A0263J
Filament
Filament
Filament
Filament
Filament
Filament
Neon
Neon
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
LED
6.3V
14V
28V
36V
48V
60V
110V
220V
6V red
6V green
6V amber
12V red
12V green
12V amber
12V blue
12V white
24V red
24V green
24V amber
24V blue
24V white
48V red
48V green
48V amber
A0141A
A0141B
A0141C
A0141D
A0141E
A0141F
A0143G
A0143H
A0142L1
A0142L2
A0142L3
A0142M1
A0142M2
A0142M3
A0142M4
A0142M5
A0142N1
A0142N2
A0142N3
A0142N4
A0142N5
A0142P1
A0142P2
A0142P3
round.
‘Illum’ - illuminated,
7.65
(.301)
Bezel Description
Plastic illum, momentary
Plastic illum, maintained
Plastic non-illum, momentary
Plastic non-illum, maintained
Metal illum, momentary
Metal illum, maintained
Metal non-illum, momentary
Metal non-illum, maintained
F/mount illum, momentary
F/mount illum, maintained
F/mount non-illum, momentary
F/mount non-illum, maintained
Plastic indicator
Metal indicator
F/mount indicator
Switch block
Lamp type
Part No
No of poles
Part No
Lamp/LED bulb
Lamp/LED bulb
A0307Y
A0307X
A0309Y
A0309X
A0310Y
A0310X
A0312Y
A0312X
A0314Y
A0314X
A0315Y
A0315X
A0375
A0377
A03791
Single pole
Double pole
Three pole
Four pole
A0151B
A0152B
A0155B
A0153B
Lamp/LED bulb
Lamp/LED bulb
Lamp/LED bulb
Lamp/LED bulb
UNSEALED SWITCHES (IP40) :
add “01” to end of operator model number.
SCREEN ENGRAVING / INSERTABLE LEGENDS : contact APEM.
‘Non-illum’ - non illuminated
www.apem.com
G-23
G