Pressure Controlled Diaphragm Pumps
Pressure controlled diaphragm pumps provide boat owners with a fresh water system
that is as easy to use as their domestic water supply - with the versatility to offer full flow
or a trickle. The pump is controlled by a switch which senses the pressure drop when a
faucet is opened and activates the pump; it turns off when the system pressure builds to
a pre-set limit as the faucet is closed. This system allows any type of faucet or shower
valve to be fitted, from 3/8" (10mm) bore for minimum water use to 1/2" (13mm) bore for
maximum flow. Choosing the pump for your needs is simple - just check your system size
and the number of outlets you need to operate simultaneously and select the appropriate
pump. Diaphragm pumps are self-priming, quiet in operation and can run dry for
extended periods.
It is always best to turn the pump off and then open a tap to de-pressurize the
system when you are not using the boat as this will prolong pump life.
Accumulator Tanks
Accumulator tanks hold a reservoir of air and water down stream from the pump.
The air acts as a cushion, absorbing pump and pressure fluctuations, smoothing the
flow and making the system quieter. Accumulators allow the pump to reach shut-off
pressure more smoothly which reduces the on/off cycle which gives better control of
hot water delivery.
Our accumulator tanks all have a bladder that separates water from air. The bladder is
pre-pressurised but may need fine tuning when installed to give the most efficient
performance. One of the advantages of an accumulator tank is that they can dispense
up to half of their capacity of water even when the pump is switched off. So the
bigger the reservoir, the more water you have available without having to switch the
pump on helping you wash your hands or clean your teeth without noise.
Water Pressure Regulators
Inlet water regulators are designed to protect your boat water system plumbing and
fixtures from the possible high pressure of municipal water systems. Regulation is
controlled at all flow rates by a pre-set spring and removable strainer traps debris.
Both inline portable and permanent flush mount models are available in our new line
of diaphragm sealed regulators.
Aqua Filta™
Everyone knows how even drinking water straight from the mains at home can be less
than perfect in taste, smell and colour. The activated carbon in Aqua Filta will absorb
chlorine and other dissolved organics, whilst the silver impregnation ensures that
bacteria do not multiply in the filter bed. In addition, the pre and post filters remove
physical debris so that your water is not only safe to drink, but tastes good, smells
good and looks good.
Not available in USA
Pumpgard™ Strainers
Inlet Strainers are an essential part of any fresh water system using a diaphragm
pump - protecting the valves from small particles in the water. Our Pumpgards™ have
been designed for easy installation and rapid filter screen cleaning having a
transparent bowl that screws off to allow simple, regular inspection.
3
Water Pressure Systems - Introduction
www.jabsco.com
15
Water Pressure Systems - Introduction
3
16
www.jabsco.com
Multi-Outlet
Water Pressure
Systems
Water Pressure
Regulators
Pumpgard™
Accumulator Tanks
PAR-Max 1, 1.9, 2.9, 3 or 4
Sensor Max VSD, Ultra Max, Dual Max VSD, 3 Chamber
PAR-Max 1.9
3 YEAR WARRANTY
PAR-Max 2.9
The NEW PAR-Max 1.9 and 2.9 Water System Pumps are designed for vessels requiring a smooth low flow, 12 or 24
Volt dc pump at an attractive low price. These new pumps are internally grounded, three chamber diaphragm
on-demand pumps with the performance characteristics to match the needs of a typical vessel with a shower, water
heater and up to three faucets. The smaller model offers a smooth flow of up to 1.9 gpm (7.2 lpm), whilst the larger
models offer 2.9 gpm (10.9 lpm), all are fitted with a built-in pulsation dampening by-pass to control unwanted
cycling and noise. We include quick-connect fittings for ease of pump installation.
■ Self priming up to 6 ft (2 m).
■ Dry running.
■ Soft rubber mounts.
■ Corrosion Resistant.
■ Complies with ISO 8846 MARINE (Ignition
Protection).
■ Very efficient - 3 chamber Vs 2 chamber.
■ Low noise.
■ Less pulsation in the flow.
■ Screw-less diaphragm design eliminates
possible leak paths.
■ Distinctive style.
■ Can eliminate the requirement for an
accumulator tank.
Fitting: 1/2" hose barb or 1/2" NPT (both supplied)
Size:
31295 - 9" long x 4.5" wide x 4.5" high
(23cm x 11cm x 11cm)
31395 - 9" long x 4.5" wide x 4.5" high
(23cm x 11cm x 11cm)
Weight: 31295 - 3 lb (1.4 kg)
31395 - 4 lb (1.8 kg)
Flow:
31295 - 0 – 1.9 gpm (0 – 7.2 lpm)
31395 - 0 – 2.9 gpm (0 – 10.9 lpm)
31295-0092
PAR-Max 1.9, 25 psi (1.7 bar),
12 Volt dc model, fuse 10 amp
31295-0094
PAR-Max 1.9, 25 psi (1.7 bar),
24 Volt dc model, fuse 6 amp
31395-0092*
PAR-Max 2.9, 50 psi (3.5 bar),
12 Volt dc model, fuse 10 amp
31395-0094*
PAR-Max 2.9, 50 psi (3.5 bar),
24 Volt dc model, fuse 6 amp
31395-0292
PAR-Max 2.9, 25 psi (1.7 bar),
12 Volt dc model, fuse 10 amp
31395-0294
PAR-Max 2.9, 25 psi (1.7 bar),
24 Volt dc model, fuse 6 amp
31395-0392
PAR-Max 2.9, 40 psi (2.8 bar),
12 Volt dc model, fuse 10 amp
31395-0394
PAR-Max 2.9, 40 psi (2.8 bar),
24 Volt dc model, fuse 6 amp
Water Pressure Systems -
PAR-Max 1.9 & 2.9 Water System Pump
3
Automatic Pressure
Controlled Pumps
www.jabsco.com
*Not available in Europe
For service and spare parts listing see page 158.
17
Pressure
Water Pressure Systems - Automatic
Controlled Pumps
3
www.jabsco.com
Sensor Max™ VSD Constant Pressure Water System Pumps
Sensor Max™ 14
Sensor Max™ 17
Weight: 31750 - 4.3 lb (2.0 kg).
Pressure sensor controlled, multi-outlet water pressure
31755 - 6.3 lb (3.0 kg).
pumps, with variable speed drive, serving 1 - 5 outlets.
Motor speed is electronically controlled to maintain steady Flow: 31750 - 0–3.7 gpm (0-14 lpm).
31755 - 0–4.5 gpm (0-17 lpm).
flow and constant pressure. Sensor Max™ VSD accepts
from 10 to 29 Volt dc for use with 12 or 24 Volt dc power. Running pressure: 31750 - 0000 - 25 psi (1.7 bar).
31750 - 0200 - 20 psi (1.4 bar).
Amp draw reduces as flow reduces to conserve energy,
31755 - 0000 - 30 psi (2.1 bar)
ranging from less than 1 amp to a maximum of 15 amps.
31755 - 0200 - 20 psi (1.4 bar)
■ Unique constant water pressure - NO pressure switch.
Shut-off pressure:
■ Electronically controlled variable flow.
■ Up to 4.5 gpm (17 lpm) output.
■ Self-priming up to 10ft (3m).
31750
31750
31755
31755
-
0000
0200
0000
0200
-
psi
psi
psi
psi
(2.4
(1.7
(2.8
(2.1
bar).
bar)
bar)
bar)
31750-0000
Sensor Max™ 14, 12-24 Volt dc model,
fuse 15 amp, high pressure.
31750-0200
Sensor Max™ 14, 12-24 Volt dc model,
fuse 15 amp, low pressure.
31755-0000
Sensor Max™ 17, 12-24 Volt dc model,
fuse 15 amp, high pressure.
■ True sensor regulated water pressure.
31755-0200
■ Thermal overload protection automatically stops motor should it
overheat due to overload, with auto re-start feature.
Sensor Max™ 17, 12-24 Volt dc model,
fuse 15 amp, low pressure.
18920-9043
Service kit, all models.
■ Gives constant flow and hot water mix.
■ Eliminates accumulator tank.
■ Runs silently under normal use.
■ Automatically adjusts to 12 Volt dc or 24 Volt dc power input.
■ Conserves battery power - uses lower amps at lower flow.
■ Diaphragm design allows extended dry running.
■ Complies with USCG 183.410 and ISO 8846 MARINE (Ignition
Protection).
Note:
copper water heating tanks.
! Sensor Max™ VSD pumps must have a battery installed.
▲
■ Pumpgard™ Strainer included
Fitting: Connections for 1/2" (13mm) ID hose or 1/2" Qest threads.
Size:
! Use only low shut-off pressure models with all
▲
For service and spare parts listing see page 162.
31750 - 9.0" long x 6.3" wide x 3.75" high
(22cm x 16cm x 9.5cm).
31755 - 10.3" long x 6.3" high x 3.75" high
(25.2cm x 16cm high x 9.5cm).
3 YEAR WARRANTY
PAR-Max 1
Included
Miniature multi outlet water pressure ■ Complies with USCG 183.410 and ISO 8846
MARINE (Ignition Protection).
pump serves 1 or 2 3/8" (10mm) outlets
at any one time. Models include both Fitting: Connections for 3/8" (10mm) ID hose
and slip-on 1/2" (13mm) bushings.
automatic and manual pumps.
■ 1.1 gpm (4.3 lpm) open flow output.
■ Self-priming up to 4ft (1.2m).
Size:
6.4" long x 3.5" wide x 2.3" high
(16cm x 9cm x 6cm).
■ Dual diaphragm operation.
Weight: 1.3 lb (0.6 kg).
■ Thermal overload protection automatically
stops motor should it overheat due to
overload, with auto re-start feature.
42630-2900
12 Volt dc model,
fuse 4 amp, automatic.
42631-2900
12 Volt dc model,
fuse 4 amp, manual.
42632-0000
Pump head repair kit.
42634-0000
Pressure switch kit.
■ Diaphragm design allows dry running.
■ Pressure switch cut-in 22 psi (1.5 bar), cut-out
35 psi (2.4 bar).
18
35
25
40
30
For service and spare parts listing see page 161.
■ Complies with USCG 183.410 and ISO 8846
New generation multi outlet water
MARINE (Ignition Protection).
pressure pump serves 3 or more
1
/2" (13mm) outlets at any one time.
Fitting: Connections for 1/2" (13mm) ID hose or
1
/2" Qest threads.
Snap-fit ports simplify both installation
and removal for routine service.
Size:
8.6" long x 4.2" wide x 4.1" high
(22cm x 10.6cm x 10cm).
■ 3.5 gpm (13.2 lpm) open flow output.
■ Self-priming up to 10ft (3m).
Weight: 4.5 lb (2.1 kg).
■ Four piston diaphragm sealed for smooth
and quiet operation.
31600-0092
12 Volt dc model,
fuse 10 amp, high pressure.
■ Thermal overload protection automatically
stops motor should it overheat due to
overload, with auto re-start feature.
31600-0094
24 Volt dc model,
fuse 7 amp, high pressure.
31600-0292
12 Volt dc model,
fuse 10 amp, low pressure.
■ Diaphragm design allows extended dry
running.
31600-0294
■ Pressure switch cut-in 10 psi (0.7 bar),
cut-out 25 psi (1.7 bar), low pressure, or
18920-9043
cut-in 20 psi (1.4 bar) cut-out 40 psi (2.8 bar),
For service and
high pressure.
3 YEAR WARRANTY
24 Volt dc model,
fuse 7 amp, low pressure.
Service kit.
spare parts listing see page 161.
PAR-Max 4 Water System Pump
New generation multi outlet water
pressure pump serves 4 or more 1/2"
(13mm) outlets at any one time. Snapfit ports simplify both installation and
removal for routine service.
Fitting: Connections for 1/2" (13mm) ID hose or
1
/2" Qest threads.
■ 4.3 gpm (16.3 lpm) open flow output.
31620-0092
12 Volt dc model,
fuse 15 amp, high pressure.
■ Four piston diaphragm sealed for smooth
and quiet operation.
31620-0094
24 Volt dc model,
fuse 7 amp, high pressure.
■ Thermal overload protection automatically
stops motor should it overheat due to
overload, with auto re-start feature.
31620-0292
12 Volt dc model,
fuse 15 amp, low pressure.
31620-0294
24 Volt dc model,
fuse 7 amp, low pressure.
Size:
9.8" long x 4.2" wide x 4.1" high (25cm
x 10.6cm x 10cm).
Weight: 6lb (2.7kg).
■ Self-priming up to 10ft (3m).
■ Diaphragm design allows extended dry
running.
31630-0092
■ Pressure switch cut-in 10 psi (0.7 bar),
cut-out 25 psi (1.7 bar), low pressure, or
cut-in 20 psi (1.4 bar) cut-out 40 psi (2.8 bar), 18920-9043
high pressure.
For service and
■ Complies with USCG 183.410 and ISO 8846 see page 161.
MARINE (Ignition Protection).
12 Volt dc model,
fuse 15 amp, high pressure,
motor dip coated.
3 YEAR WARRANTY
Service kit.
spare parts listing for the pump
Photo courtesy of Cruisers Yachts.
Water Pressure Systems -
PAR-Max 3 Water System Pump
3
Automatic Pressure
Controlled Pumps
www.jabsco.com
19
Pressure
Water Pressure Systems - Automatic
Controlled Pumps
3
www.jabsco.com
Dual Max VSD Water System
3 YEAR WARRANTY
The Dual Max VSD combines a smooth
flowing VSD Water System Pump with
a PAR-Max 4 to provide up to 8
gallons per minute when demand
increases. The VSD Pump with its
variable speed motor provides
smooth even flow as needed for
several outlets. If demand exceeds
the VSD's normal operating range the
PAR-Max 4 kicks in to add enough
additional flow to accommodate as
many as 7 outlets.
■ No need for an accumulator tank.
■ Unique constant water pressure.
31765-0092
12 Volt dc model.
■ VSD Pump is electronically controlled for
variable flow.
31765-0094
24 Volt dc model.
■ Self-priming up to 10 feet.
For service and spare parts listing for the pump
see page 162.
■ Constant flow for even hot water mix.
■ Diaphragm design allows extended dry
running.
■ Complies with USCG 183.410 and ISO 8846
for ignition protection.
Fitting: Connections 1/2" NPT.
Size:
121/2" long x 81/2" wide x 87/8" high
(32cm x 22cm x 22cm).
Weight: 131/2 lb (6kg).
Ultra Max Water Pressure Set
A fully assembled pressure set that
simplifies the installation of water
pressure systems for both the
professional and amateur installer.
The set consists of a PAR-Max 3 pump,
strainer and pre-pressurized
accumulator tank with quick connect
electrical connections on a rubber
mounted board. Serves 3 or more 1/2"
(13mm) outlets.
■ High pressure switch cut-in 20 psi (1.4 bar),
cut-out 40 psi (2.8 bar).
■ Flow of 3.5 gpm (13.2 lpm).
Weight: 6.6lb (3kg).
■ Self-priming up to 10ft (3m).
59451-0012
12 Volt dc model, fuse 10
amp, low pressure version.
■ Quadruple Diaphragms for smooth and quiet
operation.
59451-0024
24 Volt dc model, fuse 6 amp,
low pressure version.
■ Thermal overload protection automatically
stops motor should it overheat due to
overload, with auto re-start feature.
59451-1012
12 Volt dc model, fuse 10
amp, high pressure version.
59451-1024
24 Volt dc model, fuse 6 amp,
high pressure version.
■ Maintenance free potable water quality
accumulator tank.
■ Complies with USCG 183.410 and ISO 8846
MARINE (Ignition Protection).
Fitting: Connections for 1/2" (13mm) ID hose or
1
/2" (15mm) Qest fittings.
Size:
151/2" long x 153/4" wide x 51/2" high
(39cm x 40cm x 14cm).
■ Can be installed vertically or horizontally.
3 YEAR WARRANTY
■ Diaphragm design allows extended dry running.
■ Low pressure switch cut-in 10 psi (0.7bar),
cut-out 20 psi (1.4 bar).
For service and spare parts listing for the pump
see page 161.
Aqua Filta™
Aqua Filta adsorbs dissolved
impurities fresh-ening and cleansing
water to make it natural tasting,
sweet smelling and crystal clear.
■ Screw-on cartridge is replaced annually or
sooner if necessary, at half the cost of
replacement filters.
Fitting: Connections for 13mm (1/2") id hose,
15mm Hep20 and Acorn fittings,
15mm John Guest speedfit and Whale
system 15 fittings and 1/2" BSP female
threaded fittings.
Size:
23cm high x 14cm deep x
10cm wide (9" x 51/2" x 4").
■ Over 200g of silver impregnated activated
carbon.
Weight: 500g (1.1 lb).
59000-1000
Aqua Filta
■ Beneficial mineral salts are retained.
59100-0000
Replacement Filter Cartridge
■ Ports accept fitment to either 13mm (1.2")
i.d. hose or 1/2" screw-in fittings for
polybutylene or copper plumbing.
■ Initial flow capacity up to 14 lpm.
20
■ Thermal overload protection automatically
stops motors if they overheat due to
overload, with auto re-start feature.
■ Tough moulded components give ample
pressure capability, up to 4.2 bar (60 psi).
This well established and service
proven pump will serve up to 5 outlets Fitting: Connections for 1/2"-5/8" (13-16mm)
simultaneously and
ID hose.
generously.
Size:
97/8" long x 61/2" wide x 101/8" high
(25.1cm x 16.5cm x 25.8cm).
■ 4.2 gpm (16 lpm) open flow output.
■ Self-priming up to 5ft (1.5m) vertical lift.
Weight: 12lb (5.4kg).
■ Belt driven for quieter running and longer life. 36900-0200
12 Volt dc model, fuse 15 amp,
low pressure version.
■ Diaphragm design allows extended dry
running.
36900-0210
■ Low pressure switch cut-in 10 psi (0.7bar),
cut-out 20 psi (0.7 bar).
24 Volt dc model, fuse 5 amp,
low pressure version.
36900-1000
■ High pressure switch cut-in 20 psi (1.4 bar),
cut-out 40 psi (2.8 bar).
12 Volt dc model,fuse 15 amp,
high pressure version.
36900-1010
■ Complies with USCG 183.410 and ISO 8846
MARINE (Ignition Protection).
24 Volt dc model,fuse 5 amp,
high pressure version.
30121-0000
Service kit
For service and spare parts listing see page 157.
Low pressure version not available in USA
PAR 36800 Water Pressure Pump
Fitting: Connections for 1/2"-5/8" (13-16mm)
This well established and service
ID hose.
proven pump will serve up to 4 outlets
simultaneously and
Size:
97/8" long x 61/2" wide x 83/8" high
(25.1cm x 16.5cm x 21.3cm).
generously.
■ 3.3 gpm (12.5 lpm) open flow output.
Weight: 11lb (5kg).
■ Self-priming and all other benefits as PAR
36900 above.
36800-0200
12 Volt dc model,fuse 8 amp,
low pressure version.
■ Low pressure switch cut-in 10 psi (0.7bar),
cut-out 20 psi (1.4 bar).
36800-0210
24 Volt dc model,fuse 4 amp,
low pressure version.
■ High pressure switch cut-in 20 psi (1.4 bar),
cut-out 40 psi (2.8 bar).
36800-1000
12 Volt dc model,fuse 8 amp,
high pressure version.
■ Complies with USCG 183.410 and ISO 8846
MARINE (Ignition Protection).
36800-1010
24 Volt dc model,fuse 4 amp,
high pressure version.
30122-0000
Service kit
For service and spare parts listing see page 157.
Low pressure version not available in USA
PAR 36950 Water Pressure Pump
This very popular service proven
pump serves up to 4 outlets
simultaneously and generously.
■ 3 gpm (11.4 lpm) open flow output.
■ Self-priming and all other benefits as PAR
36900 above.
Fitting: Connections for 1/2"-5/8" (13-16mm)
ID hose.
Size:
71/2" long x 61/2" wide x 81/2" high
(19.1cm x 22cm x 21.6cm).
Weight: 11lb (5kg).
36950-2000
■ Low pressure switch cut-in 10 psi (0.7bar),
cut-out 20 psi (1.4 bar).
12 Volt dc model, fuse 8 amp,
high pressure version.
36950-2010
■ High pressure switch cut-in 20 psi (1.4 bar),
cut-out 40 psi (2.8 bar).
24 Volt dc model, fuse 4 amp,
high pressure version.
36950-2200
■ Complies with USCG 183.410 and ISO 8846
MARINE (Ignition Protection).
12 Volt dc model, fuse 8 amp,
low pressure version
36950-2210
24 Volt dc model, fuse 4 amp,
low pressure version.
43990-0061
Service kit
For service and spare parts listing see page 157.
Low pressure version not available in USA
Water Pressure Systems -
PAR 36900 Water Pressure Pump
3
Automatic Pressure
Controlled Pumps
www.jabsco.com
21
Water Pressure Systems -
Pumps &
Accessories
3
www.jabsco.com
Water Pressure Regulators
Water Pressure Regulators protect your Fitting: Flush connections for 3/4" GHT (f) inlet
and 1/2"-14 pipe outlet.
boat's water system from damaging
pressures of unregulated city water
In-line connections 3/4" GHT (f) inlet
and 3/4" GHT (m) outlet
hook-ups. Available in two models permanently installed flush mount or
Flush size: 31/2" deep x 43/8" high x 43/8" wide
in-line. Both feature brass GHT fittings
(88mm x 13mm x 13mm).
for potable garden hose connection.
In-line size: 3" long x 11/2" diameter
■ Limits inlet water pressure to 45 psi (3.1bar).
(7.7cm x 3.9cm).
■ Maintains regulated pressure at various flow
rates.
Weight: Flush 0.41lb (0.2 kg),
In-line 0.2lb (0.1kg)
■ Compact in-line model only 3" (77mm) long.
44411-0045
In-line, White 45psi (3.1bar).
■ Flush model has unique swivel elbow output.
44411-1045
Flush, White 45psi (3.1bar).
■ Manufactured of food-grade materials.
44411-2045
Flush, Chrome 45psi (3.1bar).
■ Meets all applicable codes and approvals.
■ Removable strainer protects plumbing.
Water System Pumpgard™ Strainer
Inlet strainer protects all electric
diaphragm pumps.
46400-0010
3
/4" (19mm) ID hose x Plug-in
90 degree.
■ Prevents unnecessary pump breakdowns
caused by particles in the water.
46400-0012
Model for 1/2" (13mm) hose
inlet 90 degree and direct plug
into PAR-Max inlet port.
46400-0014
Model for 1/2"-14 pipe inlet 90°
and direct plug into PAR-Max
inlet port.
46400-0375
3
46400-9500
Model for snap in 90° out
fitting (quad + quad).
18753-0040
Replacement 40# mesh filter.
■ Transparent housing allows instant
inspection.
■ Quick, in-place, cleaning of the 40 mesh
stainless steel screen.
Fitting: Choose connections for 3/8", 1/2", 3/4"
(13mm) ID hose, or 1/2"-14 pipe.
Size:
43/4" long x 23/4" wide x 21/2" high
(12cm x 7cm x 6cm).
46400-0000
/4" (19mm) ID hose x 3/4"
(19mm) ID hose.
46400-0002
Model for 1/2" (13mm) ID hose.
46400-0003
3
/8" (10mm) ID hose x 3/8"
(10mm) ID hose.
46400-0004
Model for 1/2"-14 pipe threads.
3
Topsider Galley Pump
An economical galley or head hand
pump.
Fitting: Connections for 1/2" (13mm) ID hose.
Size:
■ Simple countertop mounting.
31/8" long x 11/4" wide x 23/8" high
(8cm x 3cm x 6cm).
■ Smooth, convenient angled stroke.
Weight: 1lb (0.5kg).
■ Instant self-priming.
37220-1010
Topsider hand pump.
Electric Galley Pump and Faucet
The economical answer to running
water at the push of a button.
■ 1 gpm (4 lpm).
■ Available with or without faucet with
stainless steel swing spout.
22
/8" NPT (F) x 3/8" NPT (F).
Fitting: Connections for 3/8" (10mm) ID hose.
Size:
41/2" long x 21/2" wide x 13/4" high
(11.4cm x 6.4cm x 4.5cm).
Weight: 1lb (0.5kg).
42510-0000
■ Pump must be installed in flooded suction
position.
Pump only, 12 Volt dc,
fuse 3 amp.
42520-0000
Faucet only.
■ On/off switch is built into the faucet base.
42530-0000
Pump & Faucet, 12 Volt dc,
fuse 3 amp.
Improves all pressure controlled water Fitting: Connections for 1/2" (13mm) ID hose,
optional ports available, see below.
systems. Our new compact 21 oz
(0.6 Liter) accumulator tank fits into
Size:
21 oz (0.6 liter) - 43/8" deep x 43/4"
wide x 7" high (11cm x 12cm x 18cm)
those tight areas, and performs all of
the same functions as our 1 Quart
1 Quart (1 liter) - 43/8" deep x 43/4"
wide x 131/4" high (11cm x 12cm x
model (1 Liter), but in a smaller
34cm)
package.
■ Smoother flow, quieter water systems.
■ Internal rubber membrane eliminates
maintenance and allows universal mounting.
Weight: 21oz (0.6 liter) - 1 lb (0.45 kg)
1 Quart (1 liter) – 1.6 lb (0.7 kg)
30573-0003
NEW! Pressurized 21 oz
(0.6 Liter) Accumulator Tank
30573-0000
Pressurized 1 Quart (1 Liter)
Accumulator Tank
30653-0000
Snap-in port fittings for
1
/2" (12.5 mm) ID hose.
30649-0000
Snap-in port fittings for
1
/2" – 14 pipe.
30649-1000
Snap-in port fittings for 1/2"
female threads.
■ Better control of hot water temperatures.
■ Simply fitted to new or existing systems.
■ Longer pump life, lower battery drain.
■ Snap-in port fittings.
Larger Pressurized Accumulator Tanks
Smooth flow from faucets and
showers, reduce pump cycling,
eliminate pulsations and water
hammer.
18810-0000 (US supply)
■ Can be mounted vertically or horizontally.
■ Connection for 3/4" NPT male thread.
■ Water is totally separated from air chamber
by a rubber bladder.
■ 8" dia. x 125/8" high (20cm x 32cm)
■ All models include mounting brackets
■ 2 gallon Tank NSF-61 listed.
■ 100 psi (6.9 Bar) Max. working pressure,
pre-pressurized to 20 psi (1.4 Bar)
23240-2000 (European supply)
■ 8 liter (13/4 gall) volume.
■ 3.4 Bar (50psi) Max. working pressure.
■ Connection for 3/4" BSP Female thread.
■ 22cm dia. x 33cm high (81/2" x 13")
High Pressure Check Valve
When located at the pump outlet, this
high pressure check valve protects
your pump from the damaging high
pressure of unregulated city water
connection.
Also may be used at the water heater
inlet to prevent back-flow of hot
water into the cold water system
and pump.
■ Protects your pump from high city
water pressure.
■ Stops hot water migration from water
heater inlet.
Fitting: Connections for 1/2" (13mm) ID hose
Size:
11/2" (4cm) x 4" (10cm)
Weight: 1/4 lb (0.1 kg)
34344-0000
High Pressure Check Valve
Not available in Europe
21 oz (0.6 Litre)
Tank (above)
1 Quart (1 Litre)
Tank (right)
Water Pressure Systems -
Pressurized Accumulator Tanks
3
Accumulator Tanks
& Check Valve
www.jabsco.com
23