NK Standard Pumps Water supply, boosting, circulation of water in heating and air-conditioning systems. Liquid transfer in industry, agriculture, horticulture, etc. In accordance with DIN 24 255. Pump flange sizes: Maximum system pressure: Liquid temperature: DN 32-300 16 bar –40°C to +160°C TM01 0332 0897 - TM01 0200 0697 50 Hz Contents Performance Curves, 970 min-1 General Data Applications Type Key Codes for Stuffing Box Codes for Mechanical Shaft Seal Configuration Number Key Selection of Pumps for Various Liquids Operating Range Stuffing Boxes Mechanical Shaft Seals Sectional Drawing Pump Material List Motors Safety Margins According to ISO 5199 Spare Parts Page Page Page Page Page Page Page Page Page Page Page Page Page Page 3 4 4 4 5 6 7 8 9 10 13 14 14 14 Page Page Page Page Page Page 15 16 17 18 21 27 Page Page Page Page Page Page 31 31 31 32 33 34 Technical Data Electrical Data, 2-pole Electrical Data, 4-pole Electrical Data, 6-pole Pump Dimensions and Weights Unit Dimensions and Weights Quotation Drawings Performance Ranges Curve Conditions Performance Tests Certificates Performance Range, 2900 min-1 Performance Range, 1450 min-1 Performance Range, 970 min-1 Performance Curves, 2900 min-1 NK 32-xxx NK 40-xxx NK 50-xxx NK 65-xxx NK 80-xxx NK 100-xxx NK 125-250 NK 150-315 Page Page Page Page Page Page Page Page 35 38 42 46 51 55 58 59 Performance Curves, 1450 min-1 NK 32-xxx NK 40-xxx NK 50-xxx NK 65-xxx NK 80-xxx NK 100-xxx NK 125-xxx NK 150-xxx NK 200-xxx NK 250-xxx NK 300-360 2 Page Page Page Page Page Page Page Page Page Page Page 60 63 67 71 76 81 85 88 90 92 96 NK 100-200 NK 125-250 NK 150-315 NK 200-xxx NK 250-xxx NK 300-360 Page 97 Page 98 Page 99 Page 100 Page 102 Page 106 General Data NK Applications Flexible Coupling The pump is suitable for the pumping of thin, clean and non-aggressive liquids without solid particles or fibres in: Standard version or a spacer coupling which allows the motor to remain in place during the above mentioned dismantling to avoid subsequent alignment. If the pump housing, motor or the entire unit is moved, alignment is always neccessary. • District heating • Water supply • Airconditioning Bearing Assembly with Shaft • Cooling plants The bearing assembly includes two sturdy antifriction bearings lubricated for life. Oversize pumps with shaft d5 = 55 mm however, have open bearings with grease nipples. • Industry • Fire fighting • Environment engineering A thrower on the shaft prevents liquid from entering the bearing housing. Operating Conditions In stuffing box versions the shaft is protected by a stainless steel sleeve at the shaft seal. Flow Max. 2000 m 3/h. Head Max. 150 m. Liquid Temperature –40°C up to +160°C. Operating Pressure Max. 10 or 16 bar. Operating pressure = inlet pressure + pressure against a closed valve (Q = 0). Inlet Pressure Max. 9 bar. Max. 7 bar for 400 mm impellers or bigger. All the NK pumps according to DIN 24 255 are covered by only four sizes of shaft, shaft seal and bearings, and the oversizes by an additional three sizes. Due to the ample sizes of the bearings and shaft the NK pumps can be driven by a belt drive, belt variator or a diesel engine, if required. Pump Shaft Seal Non-self-priming single-stage centrifugal volute pump with axial suction port, radial discharge port and horizontal shaft components. The standard version is provided with a mechanical Burgmann shaft seal according to DIN 24 960, Grundfos type BAQE. Depending on pumped liquid and operating conditions other types and stuffing boxes are available. The NK pumps have dimensions and nominal performances according to DIN 24 255 (10 bar) but are designed for 16 bar operation wherever the shaft seal type allows it. NKG pumps according to DIN 24 256 (16 bar) are described in a separate booklet. Types outside of the official DIN-norm (NK 200 and up) will be called "oversize". Dimensions can differ from other suppliers. The suction and discharge flanges are according to DIN 2501 PN 10 or 16. All pumps are dynamically balanced according to ISO 1940 class 6.3 and impellers are hydraulically balanced. Pump and motor are mounted on a common baseplate in accordance with DIN 24 259 in all-welded steel. Oversizes have profile base frames. Due to the pump design the complete bearing assembly including impeller and shaft seal can be dismantled without removing the volute casing from the pipe system (back-pull-out system 3 ). Back-to-back double mechanical shaft seals, and "quench", are available for all variants on request. Motor The motor is a totally enclosed, fan-cooled squirrelcage Grundfos MMG motor dimensioned to IEC publication 72 and complying with IEC 34 and DIN 42 950. Mounting Designation B3 (IM 1001) Enclosure Class IP 55 Insulation Class F (100°C) Ambient Temperature Max. 40°C Voltages, 50/(60) Hz 3 x 220-240/380-415 V, (3 x 220-275/380-480 V), 3 x 380-415 ƒ V, (3 x 380-480 ƒ V) Thermistor TP 211 according to DIN 44 082 when P2 !3 kW NK units with 60 Hz motors and NKE units with MGE motors are also available, but are described in separate booklets. TM01 1666 5097 Spacer coupling Other brands of motors can be mounted on request. Surface Treatment Minimum 40 m black water based laquer (RAL 9017). Various RAL colors are available on request. 3 General Data Type Key Codes for Stuffing Box For units without motor the motor data are left out, and for bare shaft pumps the coupling and motor data are left out. Example NK NK 100 -200 /198 /A W /BAQE /1 /5.5 /4 Type range Nominal diameter of discharge port Nominal impeller diameter Position Code 1 S Position Code 2 Position Actual impeller diameter Code for materials: A = Cast iron GG 25 B = GG 25 with bronze impeller C = Ductile cast iron GGG 40 Z = All bronze Position Code for shaft seal 1 Motor power in kW 2-, 4- or 6- pole motor Position The example describes an NK 100-200 with 198 mm impeller, in cast iron with neck rings, with BAQE shaft seal, standard coupling and a 4-pole 5.5 kW motor. Specification of pump materials see, "Pump Material List" page 13. K Cooled stuffing box Code Barrier fluid With internal liquid F With external liquid O Without barrier fluid Code 2&3 4 Short Description of Seal A O-ring seal with fixed seal driver B Rubber bellows seal C O-ring seal with spring as seal driver D Balanced O-ring seal G Rubber bellows seal with reduced seal faces M Metal bellows seal X Other Code A Position 4 Uncooled stuffing box Codes for Mechanical Shaft Seal W = Neck ring(s) Coupling type 1 = standard 2 = spacer Cooling N E 3 Short Description of Seal Packing type stuffing box Material Metal-impregnated carbon B Synthetic-resin-impregnated carbon C Other types of carbon S Chromium steel U Tungsten carbide Q Silicon carbide V Aluminium oxide (ceramic) X Other types of ceramic/carbide Code Material P Nitrile (NBR) S Silicone rubber T PTFE E EPDM V FKM M PTFE-coated O-ring General Data NK Configuration Number Key Example: The fourth digit determins if the pump is with or without neck rings as well as which material version. Each of the 8 digits in the configuration number describes one or more possibilities of variation in the construction of the pump (unit). The number is configured from the tables shown below: Nominal Code Code NK Pump Material Code 1 A (cast iron GG 25) 0 Without coupling *) 2 B (GG 25 w/bronze impeller) 1 Standard 2 Spacer Impeller Diameter [mm] 125 1 160 2 3 C (ductile cast iron GGG 40) 200 3 4 Z (all bronze) 250 4 5 A *) 315 5 6 B *) 360 7 7 C *) Code 400 8 8 Z *) 0 500 9 310 A 320 C 330 B *) Bare shaft pump *) With neck ring(s) Code Single Shaft Seal 1 BAQE Coupling P2 kW max. Bare shaft pump 1 0.37 2 0.55 3 0.75 4 1.1 5 1.5 2.2 3 DAQM *) 6 Code 5 BQQV *) 7 3 32 1 7 BAQV *) 8 4 40 2 8 AQAE *) 9 5.5 50 3 9 AQAV *) A 7.5 0-55 kW 4 A SNE *) B 11 80 0-55 kW 5 B SNO *) C 15 100 0-90 kW 6 C SNF *) D 18.5 125 0-90 kW 7 D SKO *) E 22 150 0-188 kW 8 E GQQE *) F 30 37 Pump Type NK 65 65 56-200 kW *) A F GQQV *) G 80 56-200 kW *) B G BQQE *) H 45 100 91-200 kW *) C H AQQE *) K 55 125 91-188 kW *) D I AQQV *) L 75 200 0-300 kW *) E 250 0-300 kW *) F M BAQE *) 300 0-300 kW *) G N DAQM 150 189-495 kW *) H R AQAE V W Code Double Shaft Seal *) Oversize M 90 N 110 *) P 132 *) Q 160 AQQE *) R 200 AQQV *) S 250 T 315 U 355 *) Optional Code Voltage Configuration number K 6 3 5 Bare shaft pump Unit excl. motor Complete unit 1 Pole 0 Exclusive of motor 1 3X220-240/380-415V 50 Hz, 3X220-275/380-480V 60 Hz 2 3X380-415V 50 Hz, 3X380-480V 60 Hz 2 3 3X220-240/380-415V 50 Hz, 3X220-275/380-480V 60 Hz 4 2 4 3X380-415V 50 Hz, 3X380-480V 60 Hz 4 1 9 4 5 MGE-motor 3X380-415V 50/60 Hz 2 0 0 0 6 MGE-motor 3X380-415V 50/60 Hz 4 0 7 3X380-415V 50 Hz, 3X380-480V 60 Hz 6 8 3X220-240/380-415V 50 Hz, 3X220-275/380-480V 60 Hz 6 5 General Data NK Selection of Pumps for Various Liquids Materials and Shaft Seal Pumped Liquids Max. limits solution, temperature, pressure Ammonia water Max. 10%, 40°C, 16/12 bar Airconditioning 0°C to 30°C, 10/7 bar Brackish water Max. 40°C, 10/7 bar Brake fluid Max. 40°C, 16/12 bar Fire fighting water 16/12 bar Fixative salt Max. 25°C, (sodium thiosulphate) 16/12 bar Glycol-water mix Glycol-water mix with additives A Cast Iron B Bronze Impeller SNF Other coolants District heating water SNE/SNO BQQE SNE/SNO BQQV Hastelloy SNE/SNO BAQE SNE/SNO BAQE Metals in pump must be all-ferrous SNE/SNO BAQV SNE/SNO BAQE 0°C to 80°C, 10/7 bar SNE/SNO BQQE -20°C to 0°C, 10/7 bar SNE/SNO GQQE If the liquid contains oil, choose FKM SNE/SNO AQQE SNE/SNO BAQE Double seal Max. 15%, -30 to 0°C, 10/7 bar SNE/SNO AQQE -40°C to -20°C, 16 bar SNE/SNO AQAE Max. 120°C, 16 bar SNE/SNO BAQE Max. 120°C, 12 bar SNE/SNO BAQE Max. 120°C, 16 bar SNE/SNO AQAE Nominal shaft diam. "!ø48 mm SNE/SNO AQAE 140°C to 160°C, 16 bar 6 SKO Milk of lime (calcium hydroxide) Max. 10%, 25°C, 10/7 bar Condensate 0°C to 100°C, 16/12 bar SNE/SNO BAQE Cooling water 0°C to 120°C, 16/12 bar SNE/SNO BAQE SNF Max. 25°C, 10/7 bar Max. 20%, 100°C, 10/7 bar Fuel oil, diesel oil 16/12 bar SNE/SNO BQQV SNE/SNO BQQE BAQV DAQM Cooling, Contact Grundfos Flush before long standstill periods BQQE Max. 40°C, 10/7 bar Soda lye (P3) Contact Grundfos Nominal shaft diam. !ø42 mm 120°C to 140°C, 16 bar Sea water Notes Metals in pump must be all-ferrous Double seal BAQE -40°C to -20°C, 16/12 bar Salt brine Z All Bronze Stuffing Mech. Stuffing Mech. Stuffing Mech. Stuffing Mech. Box Seal Box Seal Box Seal Box Seal -20°C to 80°C, 16/12 bar Max. 15%, 0°C, 16/12 bar C Sph. Graphite Cast Iron SNE/SNO BQQV North Sea, Baltic Sea water. Hastelloy General Data NK Materials and Shaft Seal A Cast Iron Max. limits solution, temperature, pressure Pumped Liquids Z All Bronze Notes Stuffing Mech. Stuffing Mech. Stuffing Mech. Stuffing Mech. Box Seal Box Seal Box Seal Box Seal Oil-water emulsion 16/12 bar SNE/SNO BAQV Clean water 16/12 bar SNE/SNO BAQE Raw water 10/7 bar SNE/SNO BQQV Swimming pool water (fresh water) 16/12 bar SNE/SNO BAQV Saturated solution, 25°C, 10/7 bar Soda (sodium carbonate) C Sph. Graphite Cast Iron B Bronze Impeller SNE/SNO 16/16 bar BQQE Double seal DQQE Water from storage reservoirs 10/7 bar Partially demineralized water Max. 100°C, 16/12 bar Drinking water Max. 100°C, 16/12 bar Contaminated water Max. 100°C, 10/7 bar SNE/SNO BQQE SNE/SNO BAQE SNE/SNO BAQE SNF BQQV Contact Grundfos For liquids not mentioned in this table please contact Grundfos. 16/12 bar and 10/7 bar SNE/SNO The first figure is maximum pressure for nominal shaft diameters ø42 mm. The second for nominal shaft diameters ! ø48 mm. SNE for inlet pressure < 4 bar SNO for inlet pressure > 4 bar. Nominal shaft diameter is the diameter of the pump shaft end (dimension d5 on pages 18 - 20). Operating Range Hastelloy Hastelloy shaft seal metal parts for bronze pumps. Impeller Speed Relative to Material and Size 600 [mm] t [°C] RG 5 160 550 GGG 40 140 500 120 RG 10 80 GG 25 60 40 450 Oversizes GGG 40 Standard GG 25 100 GG 25 ** 400 350 20 GGG 40 -40 -60 0 2 4 6 8 10 12 14 16 18 20 22 24 26 PN [bar] 250 200 1200 1600 2000 2400 2800 3200 -1 min 3600 TM01 0834 2498 -20 TM01 2133 3698 300 0 ** Contact Grundfos 7 General Data NK Stuffing Boxes TM00 2584 0597 Uncooled stuffing box (SNE) with internal barrier fluid for the pumping of clean liquids in suction operation or at inlet pressures up to 4 bar. TM00 2585 0597 Uncooled stuffing box (SNO) without internal barrier fluid for the pumping of clean liquids in suction operation or at inlet pressures over 4 bar. TM00 2586 0597 Uncooled stuffing box (SNF) with external barrier fluid for the pumping of contaminated and malodorous liquids. TM00 2587 0597 Cooled stuffing box (SKO) for the pumping of liquids up to 160°C. 8 General Data NK Mechanical Shaft Seals TM00 4586 0597 Rubber bellows seal (BAQE), counteracts deposits from the pumped liquid. TM01 1903 0698 O-ring seal (AQAE), unbalanced, for high pressures. O-ring seal (DAQM), balanced, for high pressures and temperatures 140°C to 160°C. TM00 4588 0698 Cooled pumped liquid (120°C) is used for cooling the seal. Double seal (Back to back) to protect the primary shaft seal against wear by precipitation of abrasive matters. Quench above 80°C. TM01 3246 3698 Available on request. 9 General Data NK Sectional Drawing TM00 9796 0497 NK 32-125 -> 150-400 and NK 250-310 : Recommended spare part. Legend: A/B: Different hydraulical balancing. Pos. 10 Description Pos. Description Pos. Description 1111 Pump casing 3120 Ball bearing 6516 Gasket 1222 Seal box 3121 Ball bearing 6517 Gasket 1510 Neck ring 4200 Rotary seal ring 6521 Pressure tapping plug 1520 Neck ring 4201 Stationary seat 6522 Gasket 2002 Spacer ring 4213 Cover for seal 6546 Circlip 2110 Shaft 4223 Elastic washer 6581 Stud + nut 2200 Impeller 4522 Gasket for cover 6710 Impeller key 2540 Thrower 4596 Gasket for pump 6740 Stud + nut 2542 Thrower 6475A Thrower screw 6740A Stud + nut 2911 Impeller washer 6475B Thrower screw 6740B Stud + nut 2915 Lock nut 6511 Priming plug 6742 Coupling key 3110 Bearing housing 6515 Drain plug 6743 Foot General Data NK Sectional Drawing "Oversizes" NK 150-315, 200-500, 250-400, 250-500 6517 6511 6581 6740B 6740 4213 6475A 6546 3131 1111 1520 1510 6710 3120 2911 3852 1850 d5 6742 2912 2450 4200 6475B 6515 2542 6516 4223 4596 1222 6740A 4522 4201 2540 3110 TM00 9800 3898 2110 2200 Legend: :Recommended spare part. Pos. Description Pos. Description Pos. Description 1111 Pump casing 3110 Bearing housing 6511 Priming plug 1222 Seal box 3120 Ball bearing 6515 Drain plug 1510 Neck ring 3131 Ball bearing 6516 Gasket 1520 Neck ring 3852 Grease nipple 6517 Gasket 1850 Impeller counter nut 4200 Rotary seal ring 6546 Circlip 2110 Shaft 4201 Stationary seat 6581 Stud + nut 2200 Impeller 4213 Cover for seal 6710 Impeller key 2450 Shaft sleeve 4223 Elastic washer 6740 Stud + nut 2540 Thrower 4522 Gasket for cover 6740A Stud + nut 2542 Thrower 4596 Gasket for pump 6740B Stud + nut 2911 Impeller washer 6475A Thrower screw 2915 Impeller nut 6475B Thrower screw 6742 Coupling key 11 General Data NK Sectional Drawing "Oversizes" NK 200-400, 250-330, 300-360 TM01 3279 3798 d5 Legend: : Recommended spare part. Pos. 1111 12 Description Pump casing Pos. 3110 Description Bearing housing Pos. 6511 Description Priming plug 1222 Seal box 3120 Ball bearing 6515 Drain plug 1510 Neck ring 3131 Ball bearing 6516 Gasket 1520 Neck ring 3852 Grease nipple 6517 Gasket 1850 Impeller counter nut 4200 Rotary seal ring 6546 Circlip 2110 Shaft 4201 Stationary seat 6581 Stud + nut 2200 Impeller 4213 Cover for seal 6710 Impeller key 2450 Shaft sleeve 4223 Elastic washer 6740 Stud + nut 2540 Thrower 4522 Gasket for cover 6740A Stud + nut Gasket for pump 6740B Stud + nut 2542 Thrower 2911 Impeller washer 6475A 4596 Thrower screw 2915 Impeller nut 6475B Thrower screw 6742 Coupling key General Data NK Pump Material List Version Pos. Cast iron Component A 1111 Pump casing 1222 Seal box 1510 Neck ring 1520 Neck ring 1850 Impeller counter nut 2002 Spacer ring 2110 Shaft 2200 Impeller 2540 Thrower 2542 Thrower 2911 Impeller washer 2915 Lock nut 3110 Bearing housing Spheroidal graphite (ductile) cast iron All bronze C Z GGG 40.3 Rg 10 (SAE 63) B Bronze impeller GG 25 G-CuPb10Sn (SAE 660) GG 25 DIN 985 St. 42 DIN 985, SS AISI 304 SS AISI 420 (x20Cr13) AISI 304 (x2CrNi18-9) Rg 5 (SAE 40) GG 25 Rg 10 (SAE 63) GG 25 SS AISI 420 (x20Cr13) AISI 304 (x2CrNi18-9) DIN 985 St.42 DIN 985, SS AISI 304 GG 25 3120 3121 Ball bearing DIN 625 / 628 SKF - FAG - RHP - NSK 3131 3852 Grease nipple 4200 Rotary seal ring 4201 Stationary seat 4213 Cover for seal 4223 Elastic washer 4522 Gasket for cover 4596 Gasket for pump 6475A Thrower screw 6475B Thrower screw DIN 71412, Form D Burgmann mechanical seals GG 25 Rg 10 (SAE 63) High carbon finely tempered spring steel SAE 1070 - 1090 Asbestos free gaskets DIN FA 3535 and FKM DIN 916, SS AISI 304 6511 Priming plug 6515 Drain plug 6516 Gasket 6517 Gasket 6521 Pressure tapping plug 6522 Gasket Copper 6546 Circlip DIN 472 6581 Stud + nut 6710 Impeller key 6740 Stud + nut 6740A Stud + nut 6740B DIN 910 AISI 304 (x2CrNi18-9) DIN 910 Copper DIN 910 AISI 304 (x2CrNi18-9) DIN 910 ISO 8.8 34Cr4 + DIN 934 DIN 910 AISI 304 (x2CrNi18-9) DIN 6885 CK 45 K DIN 6885 1.4571 ISO 8.8 34Cr4 + DIN 934 ISO 8.8 AISI 304 (x2CrNi18-9) DIN 6885 CK 45 K DIN 6885 1.4571 Stud + nut 6742 Coupling key 6743 Foot 2450 Shaft Sleeve *) 4134 Lantern Ring 6855 Gland Washer 4120 Gland *) Only stuffing box or nominal shaft diameters (d5) DIN 17100 / Sf 37.2 SS AISI 420 (x20Cr13) AISI 304 (x2CrNi18-8) Rg 10 SAE 63 SS AISI 420 (x20Cr13) AISI 304 (x2CrNi18-8) GG 25 Rg10 (SAE 63) ø48 mm. 13 General Data NK Motors Spare Parts Selection of Motors Available Spare Parts Kits The power required to achieve the requested duty point can be found by means of the power chart below the performance chart (see pages 35-106). Find the power curve corresponding to the required QH-value (or interpolate between curves). When deciding the motor size a safety margin acc. ISO 5199 must be added. To decide the motor size select the P2 that is the nearest higher than the required power, and choose the motor size next to it. 1 Mechanical shaft seal complete 2 Soft packing rings 3 Bearings 4 Casing gaskets (standard or FKM) 5 Impeller 6 Shaft 7 Coupling complete (standard or spacer) 8 Rubber joints and pins for couplings 9 Neck rings 10 Nut, spacer and impeller key. Up to required pump shaft power: [kW] Use motor output P2: [kW] Up to required pump shaft power: [kW] Use motor output P2: [kW] Safety Margins According to ISO 5199 322 355 15.9 18.5 286 315 12.8 15 227 250 9.1 11 181 200 6.1 7.5 145 160 4.3 5.5 120 132 3.2 4 100 110 2.3 3 81 90 1.7 2.2 68 75 1.1 1.5 49 55 0.81 1.1 40 45 0.55 0.75 32.5 37 0.40 0.55 26 30 0.27 0.37 19 22 0.18 0.25 11 Service kit containing the above items 1 - 4 (according to pump version). (The service kit items will cover service for two years of normal operation). Ambient Temperature –30°C to +40°C. Due to the low density and consequent low cooling effect of the air, operation at an ambient temperature above 40°C or at an altitude exceeding 1000 m above sea level requires a reduction of the rated motor load. Motor load % 110 100 90 80 70 50 20 25 30 35 40 45 50 55 60 65 70 75 80 °C 1000 2250 3500 m above sea level 14 TM00 5382 0695 60 Technical Data NK Electrical Data, 2-pole 3 x 220-240ƒ/380-415Y Motor [kW] In [A] 0.37 0.55 0.75 1.1 1.5 2.2 3.0 4.0 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110 132 160 200 250 315 1.61/0.93 2.22/1.28 3.10/1.79 4.16/2.40 5.68/3.28 8.35/4.82 10.4/6.00 12.8/7.38 17.8/10.3 23.9/13.8 35.7/20.6 47.1/27.2 57.2/33.0 67.9/39.2 91.5/52.8 112/64.4 134/77.6 167/96.4 224/130 261/151 328/189 379/219 454/262 573/331 713/412 895/517 Cos ˆ 0.80 0.82 0.81 0.83 0.84 0.85 0.87 0.91 0.89 0.89 0.89 0.90 0.90 0.90 0.90 0.91 0.91 0.89 0.90 0.92 0.89 0.91 0.91 0.94 0.86 0.86 Ëmax [%] n [min-1] Ist/In [%] 71.0 76.0 75.0 80.0 78.0 80.0 83.0 86.0 87.0 87.0 87.0 89.0 90.0 90.0 91.0 91.0 92.0 93.0 93.0 94.0 94.0 94.5 95.0 96.0 95.3 95.8 2823 2843 2874 2830 2850 2839 2853 2887 2916 2896 2935 2927 2932 2945 2946 2946 2962 2969 2963 2972 2982 2980 2984 2982 2981 2985 490 590 610 600 620 610 650 740 830 660 730 730 800 680 610 680 740 780 690 710 840 730 670 710 490 570 Ëmax [%] n [min-1] Ist/In [%] 71.0 76.0 75.0 80.0 78.0 80.0 83.0 86.0 87.0 87.0 87.0 89.0 90.0 90.0 91.0 91.0 92.0 93.0 93.0 94.0 94.0 94.5 95.0 96.0 95.3 95.8 2823 2843 2874 2830 2850 2839 2853 2887 2916 2896 2935 2927 2932 2945 2946 2946 2962 2969 2963 2972 2982 2980 2984 2982 2981 2985 490 590 610 600 620 610 650 740 830 660 730 730 800 680 610 680 740 780 690 710 840 730 670 710 490 570 3 x 380-415ƒ Motor [kW] In [A] 0.37 0.55 0.75 1.1 1.5 2.2 3.0 4.0 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110 132 160 200 250 315 0.93 1.28 1.79 2.40 3.28 4.82 6.00 7.38 10.3 13.8 20.6 27.2 33.0 39.2 52.8 64.4 77.6 96.4 130 151 189 219 262 331 412 517 Cos ˆ 0.80 0.82 0.81 0.83 0.84 0.85 0.87 0.91 0.89 0.89 0.89 0.90 0.90 0.90 0.90 0.91 0.91 0.89 0.90 0.92 0.89 0.91 0.91 0.94 0.86 0.86 15 Technical Data NK Electrical Data, 4-pole 3 x 220-240ƒ/380-415Y Motor [kW] In [A] 0.37 0.55 0.75 1.1 1.5 2.2 3 4 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110 132 160 200 250 315 1.82/1.05 2.60/1.50 3.46/2.00 4.66/2.69 6.13/3.54 8.37/4.83 11.4/6.59 14.5/8.40 19.5/11.3 25.8/14.9 36.9/21.3 49.2/28.4 59.4/34.3 68.4/39.5 93.9/54.2 114/65.6 136/78.6 172/99.5 228/132 274/158 328/189 405/234 468/270 579/334 729/421 915/529 Motor [kW] In [A] 0.37 0.55 0.75 1.1 1.5 2.2 3 4 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110 132 160 200 250 315 1.05 1.50 2.00 2.69 3.54 4.83 6.59 8.40 11.3 14.9 21.3 28.4 34.3 39.5 54.2 65.6 78.6 99.5 132 158 189 234 270 334 421 529 3 x 380-415ƒ 16 Cos ˆ 0.73 0.73 0.73 0.77 0.79 0.82 0.81 0.81 0.82 0.84 0.85 0.86 0.87 0.89 0.87 0.88 0.89 0.86 0.88 0.87 0.89 0.89 0.90 0.90 0.92 0.93 Cos ˆ 0.73 0.73 0.73 0.77 0.79 0.82 0.81 0.81 0.82 0.84 0.85 0.86 0.87 0.89 0.87 0.88 0.89 0.86 0.88 0.87 0.89 0.89 0.90 0.90 0.92 0.93 Ëmax [%] n [min -1] Ist/In [%] 69.0 71.0 74.0 77.0 78.0 80.0 82.0 85.0 86.0 87.0 88.0 89.0 89.0 91.0 92.0 92.0 93.0 93.0 94.0 94.0 95.0 95.0 95.0 96.0 95.8 95.0 1371 1402 1390 1407 1385 1411 1420 1438 1446 1445 1455 1450 1468 1468 1471 1475 1475 1476 1485 1487 1484 1487 1487 1486 1490 1489 390 460 480 480 510 560 570 620 670 730 750 790 600 710 660 630 680 630 670 770 570 590 570 570 720 670 Ëmax [%] n [min -1] Ist/In [%] 69.0 71.0 74.0 77.0 78.0 80.0 82.0 85.0 86.0 87.0 88.0 89.0 89.0 91.0 92.0 92.0 93.0 93.0 94.0 94.0 95.0 95.0 95.0 96.0 95.8 95.0 1371 1402 1390 1407 1385 1411 1420 1438 1446 1445 1455 1450 1468 1468 1471 1475 1475 1476 1485 1487 1484 1487 1487 1486 1490 1489 390 460 480 480 510 560 570 620 670 730 750 790 600 710 660 630 680 630 670 770 570 590 570 570 720 670 Technical Data NK Electrical Data, 6-pole 3 x 220-240ƒ/380-415Y Motor [kW] In [A] 0.37 0.55 0.75 1.1 1.5 2.2 3.0 4.0 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110 132 160 200 250 2.18/1.26 3.00/1.73 3.91/2.26 5.39/3.11 6.72/3.88 9.35/5.40 12.3/7.13 15.8/9.11 21.0/12.1 28.4/16.4 40.7/23.5 52.1/30.1 62.9/36.3 72.4/41.8 98.0/56.6 116/66.9 141/81.3 173/99.7 238/138 288/166 341/197 409/236 481/278 600/346 748/432 Cos ˆ 0.69 0.71 0.71 0.73 0.74 0.75 0.77 0.77 0.78 0.76 0.76 0.81 0.82 0.84 0.83 0.87 0.86 0.86 0.83 0.84 0.85 0.85 0.87 0.88 0.88 Ëmax [%] n [min-1] Ist/In [%] 61.0 65.0 68.0 71.0 75.0 78.0 81.0 82.0 84.0 87.0 89.0 89.0 90.0 90.0 91.0 92.0 92.0 93.0 94.0 94.0 94.0 95.0 95.0 95.8 94.9 905 907 914 910 932 932 939 963 964 966 970 976 979 978 983 980 985 986 991 987 991 992 991 991 990 300 330 380 400 460 470 570 610 650 630 660 630 610 620 600 670 690 700 610 590 770 720 640 630 670 Ëmax [%] n [min-1] Ist/In [%] 61.0 65.0 68.0 71.0 75.0 78.0 81.0 82.0 84.0 87.0 89.0 89.0 90.0 90.0 91.0 92.0 92.0 93.0 94.0 94.0 94.0 95.0 95.0 95.8 94.9 905 907 914 910 932 932 939 963 964 966 970 976 979 978 983 980 985 986 991 987 991 992 991 991 990 300 330 380 400 460 470 570 610 650 630 660 630 610 620 600 670 690 700 610 590 770 720 640 630 670 3 x 380-415ƒ Motor [kW] In [A] 0.37 0.55 0.75 1.1 1.5 2.2 3.0 4.0 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110 132 160 200 250 1.26 1.73 2.26 3.11 3.88 5.4 7.13 9.11 12.1 16.4 23.5 30.1 36.3 41.8 56.6 66.9 81.3 99.7 138 166 197 236 278 346 432 Cos ˆ 0.69 0.71 0.71 0.73 0.74 0.75 0.77 0.77 0.78 0.76 0.76 0.81 0.82 0.84 0.83 0.87 0.86 0.86 0.83 0.84 0.85 0.85 0.87 0.88 0.88 17 Technical Data NK Dimensions [mm] Type 32-125 32-160 32-200 40-125 40-160 40-200 40-250 50-125 50-160 50-200 50-250 65-125 65-160 65-200 65-250 65-315 *65-315 80-160 80-200 80-250 80-315 *80-315 *80-400 100-200 100-250 100-315 *100-315 100-400 125-250 *125-250 125-315 125-400 150-315 150-400 * Oversize 18 DNs DNt a f 50 32 80 360 65 40 80 80 100 100 360 65 50 100 360 80 65 100 100 100 100 125 125 100 100 100 100 100 125 80 125 125 100 125 140 140 140 140 150 125 140 360 360 360 470 470 530 360 470 470 470 530 530 470 470 470 530 530 470 530 530 530 200 150 160 530 A Priming plug E Drain plug M Pressure gauge tapping V Pressure/vacuum gauge tapping Supporting Feet [mm] h1 h2 112 132 160 112 132 160 180 132 160 160 180 160 160 180 200 225 225 180 180 200 250 250 280 200 225 250 250 280 250 250 280 315 280 315 140 160 180 140 160 180 225 160 180 200 225 180 200 225 250 280 280 225 250 280 315 315 355 280 280 315 315 355 355 355 355 400 400 450 b 50 50 50 50 65 50 50 50 65 65 65 65 80 80 80 65 65 80 80 80 80 80 80 80 80 100 80 80 100 100 100 c m1 m2 n1 n2 140 190 190 160 190 212 250 190 212 212 250 212 212 250 280 315 315 250 280 315 315 315 355 280 315 315 315 400 315 315 400 400 450 100 70 12 12 12 14 15 15 12 12 14 16 16 16 14 15 16 16 20 16 16 20 20 100 100 100 125 100 100 100 125 125 125 125 160 160 160 125 125 160 160 160 160 160 160 160 160 200 160 160 200 200 70 70 70 95 70 70 70 95 95 95 95 120 120 120 95 95 120 120 120 120 120 120 120 120 150 120 120 150 150 190 240 240 210 240 265 320 240 265 265 320 280 280 320 360 400 400 320 345 400 400 400 435 360 400 400 400 500 400 400 500 500 20 200 150 550 12 12 12 Shaft [mm] Weight [kg] TM01 0526 4997 Pump Dimensions and Weights s1 s2 w d5 l t n x 12 12 260 24 50 27 8 80 12 12 260 24 50 27 8 80 12 12 260 24 50 27 8 80 24 24 24 32 32 42 24 32 32 32 42 42 32 32 32 42 42 32 42 42 42 50 50 50 80 80 110 50 80 80 80 110 110 80 80 80 110 110 80 110 110 110 27 27 27 35 35 45 27 35 35 35 45 45 35 35 35 45 45 35 45 45 45 8 8 8 10 10 12 8 10 10 10 12 12 10 10 10 12 12 10 12 12 12 80 80 80 100 100 100 80 100 100 100 100 140 12 12 12 12 14 12 12 14 14 260 260 260 340 340 370 260 340 340 340 370 370 340 340 340 370 370 340 370 370 370 100 120 120 120 34 37 47 34 39 49 64 34 42 56 67 41 46 55 89 117 136 55 73 93 123 142 198 83 101 130 151 179 118 139 170 193 14 370 42 110 45 12 120 210 12 12 12 16 16 16 12 12 14 16 16 16 16 16 16 16 20 16 16 20 20 20 12 12 100 Technical Data NK TM01 2148 1298 Pump Dimensions and Weights a *150-315 *200-500 *250-400 *250-500 200 250 150 200 300 250 160 250 200 300 Supporting Feet [mm] f h1 h2 b 700 750 740 750 280 410 400 410 400 675 600 660 100 140 Shaft [mm] c m1 m2 n1 n2 s1 20 22 20 23 200 150 190 450 660 580 660 20 28 250 550 790 700 790 s2 w 24 515 536 530 536 28 d5 l t n x 120 55 140 59 16 235 480 415 507 180 Dimensions [mm] Type *250-310 DN s DNt 300 250 Supporting Feet [mm] a f h1 h2 k1 k2 p b c m1 m2 n1 n2 r1 r2 250 565 400 400 358 498 295 140 22 300 250 330 330 400 400 Shaft [mm] s1 s2 28 20 w d5 l t n x 289 42 110 45 12 180 Weight [kg] TM01 3281 3798 Type DNt Weight [kg] Dimensions [mm] DNs 350 * Oversize 19 Technical Data NK Dimensions [mm] Type DN s DNt a f h1 h2 Supporting Feet [mm] k1 k2 p b c m1 m2 n1 n2 r1 r2 Shaft [mm] s1 s2 w d5 l *200-400 250 200 180 750 400 400 268 460 290 130 25 300 230 155 215 220 280 28 24 536 55 140 *250-330 250 250 250 740 450 400 338 545 345 130 25 350 280 245 325 310 390 34 24 600 55 140 *300-360 300 300 300 760 520 440 410 580 355 160 25 320 280 337 337 420 420 26 24 540 55 140 * Oversize t 59 59 59 n x Weight [kg] TM01 0527 4997 Pump Dimensions and Weights 16 200 405 16 200 430 16 280 560 Flange Dimensions [mm] DIN 2501 PN 16 DIN 2501 PN 10 TM01 1538 4997 Nominal diameter (DN) 32 40 50 65 80 100 125 150 200 250 300 D1 32 40 50 65 80 100 125 150 200 250 300 D2 100 110 125 145 160 180 210 240 295 350 400 D3 140 150 165 185 200 220 250 285 340 395 445 S 4 x 18 4 x 18 4 x 18 4 x 18 8 x 18 8 x 18 8 x 18 8 x 22 8 x 22 12 x 22 12 x 22 Oversizes The DIN 24 255 describes only the standard types mentioned in the table on page 18. The NK range is extended with bigger models (oversizes) for higher flows and pressures. As a consequence bracket sizes, flange dimensions etc. for the oversize pumps can be different from other suppliers. 20 Technical Data NK TM01 0528 4997 Unit Dimensions and Weights The standard baseplate has only four holes for foundation bolts. Type 32-125 32-160 32-200 40-125 40-160 40-200 40-250 50-125 50-160 Motor Motor [kW] Size 0.55 0.75-1.1 1.5 2.2 0.75-1.1 1.5 2.2 3 4 5.5 3 4 5.5-7.5 0.75-1.1 1.5 2.2 3 2.2 3 4 5.5-7.5 3 4 5.5-7.5 11-15 5.5-7.5 11-15 18.5 22 1.5 2.2 3 4 5.5-7.5 3 4 5.5-7.5 11 Common [mm] a a2 h2 80 90S 90L 80 90S 90L 100L 112M 132S 100L 112M 132S 80 90S 90L 100L 90L 100L 112M 132S 100L 112M 132S 160M 132S 160M 160L 180M 90S 90L 100L 112M 132S 100L 112M 132S 160M L h 2900 min-1 (2-pole motors) With Standard Coupling [mm] Weight h3 L1 L3 b2 b3 d [kg] 715 80 80 80 80 80 60 140 60 160 60 180 60 140 60 160 100 60 180 100 75 225 100 60 160 100 60 180 767 767 715 767 767 804 827 940 804 827 940 715 767 767 804 767 804 827 940 804 827 940 1050 955 1065 1110 1140 767 767 804 827 940 804 827 940 1050 65 177 800 540 360 320 900 600 390 350 800 540 360 320 900 600 390 350 65 197 70 19 19 80 240 1000 660 450 400 24 65 225 900 600 390 350 19 80 240 1000 660 450 400 24 800 540 360 320 900 600 390 350 65 177 19 65 197 900 600 390 350 19 80 212 1000 660 450 400 24 65 225 900 600 390 350 19 1000 660 450 400 80 240 24 1120 740 490 440 1120 740 490 440 80 260 65 197 1250 840 540 490 800 540 360 320 900 600 390 350 24 19 80 212 1000 660 450 400 24 65 225 900 600 390 350 19 1000 660 450 400 80 240 24 1120 740 490 440 81 95 83 89 103 108 121 166 118 131 174 79 90 95 100 100 105 118 155 115 128 165 220 187 252 277 308 86 95 101 114 145 109 122 158 202 L h With Spacer Coupling [mm] Weight h3 L1 L3 b2 b3 d [kg] 855 907 907 855 907 907 944 967 1080 944 967 1080 855 907 907 944 907 944 967 1080 944 967 1080 1190 1095 1205 1250 1280 907 907 944 967 1080 944 967 1080 1190 800 540 360 320 65 177 65 197 900 600 390 350 800 540 360 320 900 600 390 350 1000 1120 65 225 900 1000 80 240 1120 800 80 240 65 177 70 19 900 660 740 600 660 740 540 450 490 390 450 490 630 600 390 1000 1120 65 225 900 1000 80 240 1120 1250 1120 80 260 1250 660 740 600 660 740 840 740 80 212 400 24 440 350 19 400 24 440 320 600 390 350 65 197 900 19 350 19 19 450 490 390 450 490 540 490 400 24 440 350 19 400 440 24 490 440 24 840 540 490 100 280 1400 940 610 550 28 65 197 900 80 212 600 390 350 19 1000 660 450 400 24 1120 740 490 440 1000 660 450 400 80 240 1120 740 490 440 1250 840 540 490 24 86 95 83 94 103 108 131 175 116 139 185 82 93 97 102 102 107 131 165 117 141 176 235 192 260 280 331 93 97 115 128 159 128 141 168 228 * Oversize 21 Technical Data Type 50-200 50-250 65-125 65-160 65-200 65-250 65-315 65-315 * 80-160 80-200 80-250 80-315 80-315 * 100-200 100-250 100-315 100-315 * Motor Motor [kW] Size 5.5-7.5 11-15 18.5 22 11-15 18.5 22 30 4 5.5-7.5 11 5.5-7.5 11-15 18.5 7.5 11-15 18.5 22 30 18.5 22 30-37 45 37 45 55 75 90 7.5 11-15 18.5 22 30 15 18.5 22 30-37 45 18.5 22 30-37 45 55 75 45 55 75 90 110 132 22 30-37 45 55 75 37 45 55 75 90 110 55 75 90 110 132 160-200 * Oversize 22 132S 160M 160L 180M 160M 160L 180M 200L 112M 132S 160M 132S 160M 160L 132S 160M 160L 180M 200L 160L 180M 200L 225M 200L 225M 250M 280S 280M 132S 160M 160L 180M 200L 160M 160L 180M 200L 225M 160L 180M 200L 225M 250M 280S 225M 250M 280S 280M 315S 315M 180M 200L 225M 250M 280S 200L 225M 250M 280S 280M 315S 250M 280S 280M 315S 315M 315L Common [mm] a a2 h2 100 60 200 100 75 225 100 75 180 100 75 200 100 75 225 100 90 250 125 90 280 125 90 280 125 75 225 125 75 250 125 90 280 125 90 315 125 90 315 125 90 280 140 90 280 140 90 315 L 940 1050 1095 1125 1065 1110 1140 1220 842 955 1065 955 1065 1110 955 1065 1110 1140 1220 1232 1262 1342 1397 1342 1397 1507 1642 1582 955 1065 1110 1140 1220 1171 1216 1246 1326 1381 1232 1262 1342 1397 1507 1532 1397 1507 1592 1642 1967 1967 1262 1342 1397 1507 1532 1342 1397 1507 1532 1582 1768 1507 1532 1582 h NK 2900 min-1 (2-pole motors) With Standard Coupling [mm] Weight h3 L1 L3 b 2 b3 d [kg] 1000 660 450 400 80 240 1120 740 490 440 24 260 80 260 1250 840 540 490 24 100 280 1400 65 225 900 1000 80 240 1120 1120 80 240 1250 940 600 660 740 740 610 390 450 490 490 550 28 350 19 400 24 440 440 24 840 540 490 1120 740 490 440 80 260 1250 840 540 24 490 1250 540 24 100 300 1400 940 610 550 80 280 1250 840 540 490 24 300 1400 940 610 550 28 325 1400 940 610 550 325 100 1600 1060 660 600 350 28 100 100 380 1800 1200 730 670 1120 740 490 440 80 260 1250 840 540 490 24 1250 840 540 950 100 300 1400 940 610 550 28 80 260 1250 840 540 490 24 280 100 300 1400 325 1250 80 280 1250 300 1400 325 100 350 1600 380 1800 940 610 550 28 840 540 490 24 840 540 490 940 610 550 1060 660 600 1200 730 670 28 100 350 1600 1060 660 600 28 100 380 1800 1200 730 670 28 120 435 2000 1340 910 830 80 280 300 325 100 350 380 325 100 350 1250 840 540 490 24 1400 940 610 550 1600 1060 660 600 1800 1200 730 670 1400 940 610 550 28 1600 1060 660 600 28 380 1800 1200 730 670 120 435 2000 1340 910 830 350 1600 1060 660 600 100 28 380 1800 1200 730 670 140 90 315 1967 120 435 2000 1340 910 830 28 172 229 254 285 276 280 311 391 124 146 197 186 234 259 200 248 268 299 379 294 338 421 493 478 552 631 781 832 162 248 268 304 379 247 279 328 406 477 333 345 426 499 588 738 584 659 787 838 1194 1272 336 416 487 578 728 456 518 596 746 797 1180 630 800 900 1203 1329 1520 L 1080 1190 1235 1265 1205 1250 1280 1360 982 1095 1205 1095 1205 1250 1095 1205 1250 1280 1360 1372 1402 1482 1537 1482 1537 1647 1782 1722 1095 1205 1250 1280 1360 1311 1356 1386 1466 1521 1372 1402 1482 1537 1647 1672 1537 1647 1732 1782 2107 2107 1402 1482 1537 1647 1672 1482 1537 1647 1672 1722 1900 1647 1672 1722 h With Spacer Coupling [mm] Weight h3 L1 L3 b 2 b3 d [kg] 1120 740 490 440 80 240 1250 840 540 490 24 260 80 260 1250 840 540 490 24 100 280 1400 940 610 550 28 1000 1120 100 260 1400 1120 80 240 1250 80 240 660 740 940 740 450 490 610 490 400 29 440 550 28 440 24 840 540 490 1120 740 490 440 80 260 1250 840 540 490 280 1400 100 300 1250 80 280 1400 100 300 1600 325 100 24 940 610 550 28 840 540 490 24 940 610 550 28 1060 660 600 325 1600 1060 660 600 28 350 1800 1200 730 670 100 380 1800 1200 730 670 28 1120 740 490 440 80 260 1250 840 540 490 100 300 24 1400 940 610 550 28 80 260 1250 840 540 490 24 280 1400 940 100 300 1600 1060 325 1250 840 80 280 1400 940 300 1600 1060 325 100 350 1800 1200 380 610 550 660 600 28 540 490 24 610 550 660 600 28 730 670 100 350 1800 1200 730 670 28 100 380 1800 1200 730 670 28 120 435 2000 1340 910 830 80 280 1400 940 610 300 325 1600 1060 660 100 350 380 1800 1200 730 1600 1060 660 325 100 350 550 600 28 670 600 1800 1200 730 670 28 380 120 435 2000 1340 910 830 350 100 1800 1200 730 670 28 380 2107 120 435 2000 1340 910 830 28 194 252 272 303 263 283 334 396 142 151 230 194 242 262 228 286 306 322 384 304 356 442 510 476 538 636 786 837 176 251 271 322 380 293 313 362 432 494 306 382 452 514 612 743 589 664 792 843 1224 1302 361 442 504 602 733 492 566 620 751 802 1190 676 830 930 1233 1335 1527 Technical Data Type Motor Motor [kW] Size 37 45 55 75 90 110 132 90 110 132 125-250 125-250 * 150-315 160 200 250 150-315 * 315 200L 225M 250M 280S 280M 315S 315M 280M 315S 315M Common [mm] a a2 h2 L h NK 2900 min-1 (2-pole motors) With Standard Coupling [mm] Weight h3 L1 L3 b2 b3 d [kg] 1448 1400 940 610 550 1488 350 1600 1060 660 600 140 90 355 1603 100 28 1673 380 1800 1200 730 670 1723 140 90 355 1967 120 435 2000 1340 910 830 28 1744 100 380 1800 1200 730 670 1849 28 160 110 400 1904 120 435 2000 1340 910 830 28 315Lk 1989 ** 315L 2159 435 28 355S 2216 160 110 400 120 2000 1340 910 830 475 28 355M 2216 ** 467 565 634 784 835 1191 1269 913 1295 1373 L h With Spacer Coupling [mm] Weight h3 L1 L3 b2 b3 d [kg] 1590 1600 1060 660 600 1625 350 1740 100 28 1810 1800 1200 730 670 380 1860 2107 120 435 2000 1340 910 830 28 1507 1884 100 380 1800 1200 730 670 1985 28 2044 120 435 2000 1340 910 830 2129 1602 1998 2299 2356 2173 2556 435 120 475 2000 1340 910 830 28 498 539 637 740 840 1221 1293 911 1292 1370 1556 1619 2005 2183 * Oversize 1450 min (4-pole motors) Common With Standard Coupling With Spacer Coupling Motor [mm] [mm] Type Motor Weight [kW] Size a a h L h h L L b b d [kg] L h h L[mm]L b b d Weight [kg] -1 2 32-125 32-160 32-200 40-125 40-160 40-200 40-250 50-125 50-160 50-200 50-250 65-125 65-160 65-200 2 0.37 71 80 60 140 693 0.37 71 693 80 60 160 0.55-0.75 80 738 0.37 71 693 0.55-0.75 80 80 60 180 738 1.1 90S 758 0.37 71 80 60 140 693 0.37 71 693 0.55-0.75 80 80 60 160 738 1.1 90S 758 0.55-0.75 80 758 1.1 90S 100 60 180 778 1.5 90L 803 0.75 80 758 1.1 90S 778 100 75 225 1.5 90L 803 2.2-3 100L 848 0.37 71 713 100 60 160 0.55-0.75 80 758 0.55-0.75 80 758 1.1 90S 100 60 180 778 1.5 90L 803 0.75 80 758 1.1 90S 778 100 60 200 1.5 90L 803 2.2-3 100L 848 1.1 90S 778 1.5 90L 803 100 75 225 2.2-3 100L 848 4 112M 863 0.55-0.75 80 758 1.1 90S 100 75 180 778 1.5 90L 803 0.75 80 758 1.1 90S 778 100 75 200 1.5 90L 803 2.2-3 100L 848 1.1 90S 782 1.5 90L 100 75 225 2.2-3 100L 820 4 112M 842 3 1 3 2 3 3 65 177 800 540 360 320 19 65 197 800 540 360 320 19 65 225 800 540 360 320 19 65 177 800 540 360 320 19 65 197 800 540 360 320 19 65 225 900 600 390 350 19 80 260 1000 660 450 400 24 65 197 800 540 360 320 19 65 225 900 600 390 350 19 65 225 900 600 390 350 19 80 260 1000 660 450 400 24 65 225 900 600 390 350 19 65 225 900 600 390 350 19 80 240 1000 660 450 400 24 1000 660 450 400 80 260 24 1120 740 490 440 67 71 83 81 93 99 68 73 85 91 100 106 110 126 132 136 144 68 80 93 99 103 107 113 117 125 135 139 142 160 92 98 102 97 114 118 126 123 127 142 155 790 790 835 790 835 855 790 790 835 855 855 875 900 855 875 900 945 810 855 855 875 900 855 875 900 950 875 900 945 960 855 875 900 855 875 900 945 65 197 800 65 225 3 2 3 540 360 320 19 540 360 320 19 800 540 360 320 900 600 390 350 19 65 177 800 800 65 197 900 540 360 320 19 540 360 320 19 600 390 350 65 225 900 600 390 350 19 80 260 1000 660 450 400 24 800 900 540 360 320 19 600 390 350 65 225 900 600 390 350 19 65 225 900 600 390 350 19 65 197 80 260 1000 660 450 400 24 65 225 900 600 390 350 19 65 225 900 600 390 350 19 80 240 1000 660 450 400 24 922 960 982 1 65 177 800 1000 660 450 400 80 260 24 1120 740 490 440 67 71 83 84 100 106 71 76 92 98 102 108 112 128 134 138 146 71 87 95 101 105 109 115 119 127 140 144 150 162 76 82 104 109 116 120 128 119 132 145 157 * Oversize ** Profile base frame with six holes for foundation bolts 23 Technical Data NK 1450 min (4-pole motors) Common With Standard Coupling With Spacer Coupling Motor [mm] [mm] Type Motor Weight [kW] Size a a h L h h L L b b d [kg] L h h L[mm]L b b d Weight [kg] -1 2 65-250 65-315 80-160 80-200 80-250 80-315 80-400 * 100-200 100-250 100-315 100-400 125-250 2.2-3 4 5.5 7.5 4 5.5 7.5 11 15 1.1 1.5 2.2-3 2.2-3 4 5.5 7.5 3 4 5.5 7.5 11 5.5 7.5 11 15 18.5 11 15 18.5 22 30 37 3 4 5.5 7.5 11 5.5 7.5 11 15 18.5 22 7.5 11 15 18.5 22 30 15 18.5 22 30 37 45 55 75 5.5 7.5 11 15 18.5 22 100L 112M 132S 132M 112M 132S 132M 160M 160L 90S 90L 100L 100L 112M 132S 132M 100L 112M 132S 132M 160M 132S 132M 160M 160L 180M 160M 160L 180M 180L 200L 225S 100L 112M 132S 132M 160M 132S 132M 160M 160L 180M 180L 132M 160M 160L 180M 180L 200L 160L 180M 180L 200L 225S 225M 250M 280S 132S 132M 160M 160L 180M 180L 2 100 90 250 3 945 967 1 2 3 3 80 280 1120 740 490 440 24 1077 967 125 90 280 1077 80 305 1250 840 540 490 24 1187 1232 100 325 1400 940 610 550 28 125 75 225 125 75 250 782 820 928 951 80 260 1000 660 450 400 24 1120 740 490 440 80 260 1120 740 490 440 24 1061 945 967 125 90 280 1077 80 280 1250 840 540 490 24 1187 1077 80 330 1250 840 540 490 24 125 90 315 1187 1232 100 350 1400 940 1262 1282 1327 1357 1400 940 170 125 355 100 380 1397 1437 1522 1600 1060 945 967 1120 740 125 90 280 80 280 1077 1187 1077 1187 1232 1262 1302 1077 1187 1232 140 90 315 1262 1302 1342 1333 1343 1302 1342 140 110 355 1397 610 550 28 610 550 28 660 600 490 440 24 1250 840 540 490 80 305 1250 840 540 490 24 140 90 280 1507 1532 1077 140 90 355 100 325 100 1400 940 610 550 28 1400 940 610 550 28 80 330 1250 840 540 490 24 100 350 1400 940 610 550 28 100 380 1600 1060 660 600 28 1800 1200 730 670 80 330 1250 840 540 490 24 1187 1232 1262 100 350 1400 940 610 550 28 1302 * Oversize ** Profile base frame with six holes for foundation bolts 24 3 176 189 210 221 237 259 264 304 349 132 136 142 160 173 194 205 198 209 229 240 283 255 266 309 355 387 410 431 463 484 545 602 172 183 204 215 276 234 244 287 353 382 390 279 322 362 394 414 474 430 462 480 536 581 614 671 850 250 261 304 350 382 400 1085 1107 1 3 2 3 80 280 1120 740 490 440 24 1217 1107 1217 80 305 1250 840 540 490 24 1327 1372 100 325 1400 940 610 550 24 922 80 260 1000 660 450 400 960 1068 1091 1120 740 490 440 24 1120 740 490 440 80 260 1201 24 1250 840 540 490 1085 1107 1217 80 280 1250 840 540 490 24 1327 1217 80 330 1250 840 540 490 24 1327 1372 100 350 1400 940 1402 1422 1400 940 1467 1497 100 380 1537 1600 1060 1577 1622 1085 1120 740 1007 80 280 1217 1250 840 610 550 28 610 550 660 600 28 490 440 24 540 490 1327 100 300 1400 940 610 550 28 1217 80 305 1250 840 540 490 24 1327 1372 100 1400 940 610 1402 315 1442 1217 80 330 1250 840 540 1327 1372 1402 100 350 1400 940 610 1442 1550 1475 1482 1442 1600 1060 660 1482 100 380 1537 1647 1672 550 28 490 24 550 28 600 28 1800 1200 730 670 1217 80 330 1250 840 540 490 24 1327 1372 100 350 1400 940 610 550 28 1402 1442 178 191 213 239 182 202 267 307 352 128 132 145 164 175 212 232 201 212 232 243 286 262 273 336 358 390 410 440 474 492 559 602 172 183 222 233 329 240 271 314 356 390 395 302 345 365 397 419 480 435 465 485 541 586 638 695 855 257 288 331 353 385 403 Technical Data NK 1450 min (4-pole motors) Common With Standard Coupling With Spacer Coupling Motor [mm] [mm] Type Motor Weight [kW] Size a a h L h h L L b b d [kg] L h h L[mm]L b b d Weight [kg] -1 2 125-315 125-400 150-315 150-400 200-400 * 200-500 * 250-310 * 250-330 * 250-400 * 250-500 * 11 15 18.5 22 30 15 18.5 22 30 37 45 55 75 11 15 18.5 22 30 37 45 22 30 37 45 55 75 90 110 45 55 75 90 110 132 55 75 90 110 132 160 200 250 30 37 45 55 75 55 75 90 110 55 75 90 110 132 160 200 90 110 132 160 200 250 315 160M 160L 180M 180L 200L 160L 180M 180L 200L 225S 225M 250M 280S 160M 160L 180M 180L 200L 225S 225M 180L 200L 225S 225M 250M 280S 280M 315S 225M 250M 280S 280M 315S 315M 250M 280S 280M 315S 315M 315Lk 315L 355S 200L 225S 225M 250M 280S 250M 280S 280M 315S 250M 280S 280M 315S 315M 315Lk 315L 280M 315S 315M 315Lk 315L 355S 355M 2 3 1 3 2 3 3 1367 1312 140 110 355 1342 100 380 1600 1060 660 600 28 1382 1422 1312 1342 1382 1422 1600 1060 660 600 140 110 400 100 415 28 1507 1587 1612 1800 1200 730 670 1275 1600 1060 660 600 1320 1350 160 110 400 1390 100 380 28 1430 1800 1200 730 670 1515 1382 1422 1507 100 415 1800 1200 730 670 28 160 110 450 1587 1612 1683 120 435 2000 2017 245 1797 160 470 1900 1877 2000 1902 490 180 400 180 1952 255 2100 495 1375 200 515 2200 1947 160 480 1900 175 1972 490 2000 2022 180 495 250 675 2100 185 2377 200 515 1340 910 830 1500 680 690 1600 715 1700 750 1800 760 1600 735 1700 175 300 185 132 134 660 650 18** 685 690 675 945 880 18** 1800 220 535 2200 1900 2444 240 595 2300 2000 1597 140 480 195 1700 1500 1682 505 250 400 160 1762 510 205 1800 1600 1787 180 560 1937 1962 250 220 400 120 570 2000 1340 2012 2367 1887 160 470 1900 1600 175 1912 480 2000 1700 1962 180 200 600 495 2100 1800 185 2317 200 515 132 620 625 955 885 965 890 975 895 22** 830 950 18 820 810 910 830 28 850 790 860 795 18** 870 800 220 535 2200 1900 880 805 2072 490 2000 1700 180 945 800 495 2100 1800 2427 200 515 955 885 18** 220 535 2200 1900 965 890 240 595 2300 2000 975 890 2894 240 615 2400 2100 985 900 22** 397 417 446 448 527 450 482 500 556 597 628 685 864 420 440 489 507 586 631 664 516 572 613 646 721 881 980 1266 890 942 1006 1190 1488 1639 1046 1200 1301 1579 1633 1837 1970 2262 630 680 750 795 900 940 1085 1185 1470 1004 1158 1258 1536 1690 1806 1906 1416 1694 1830 1930 2030 2268 2460 1 1407 1452 1482 100 380 1600 1522 1562 1452 1482 1600 1522 1562 100 415 1647 1800 1727 1752 1415 1460 1490 1530 100 380 1800 1570 3 2 3 1060 660 600 28 1060 600 600 28 1200 730 670 1200 730 670 28 1655 1522 1562 1647 100 415 1800 1200 730 670 1727 1752 1823 120 435 2000 2157 1997 160 470 1900 2077 2000 2102 490 180 2152 2100 495 2507 200 515 2200 2147 160 480 1900 2172 490 2000 2222 180 495 2100 2577 200 515 28 1340 910 830 1500 680 690 1600 715 1700 750 1800 760 1600 735 1700 620 625 650 18* 685 690 675 945 880 18* 1800 955 885 220 535 2200 1900 965 890 3044 240 595 2300 2000 975 895 22* 1797 140 480 1700 1500 830 1882 1962 1987 2137 2162 2212 2567 2087 2112 2162 160 180 120 160 180 160 180 505 1800 1600 510 560 570 460 480 495 470 950 820 18 1900 170 810 2000 1340 910 830 2100 1800 850 790 1900 1600 850 790 480 2000 1700 860 795 495 2517 200 515 18 2200 1900 860 795 18* 2100 1800 870 800 220 535 2200 1900 880 805 2272 490 2000 1700 180 945 800 495 2100 1800 2627 200 515 955 885 18* 220 535 2200 1900 965 890 240 595 2300 2000 975 890 3094 240 615 2400 2100 985 900 22* 400 420 449 471 532 454 486 505 560 620 652 709 869 424 445 494 530 591 636 669 520 578 620 654 726 886 1010 1298 898 950 1108 1196 1499 1650 1054 1210 1312 1590 1744 1858 1986 2283 660 690 765 810 920 942 1195 1280 1580 1012 1170 1270 1547 1701 1822 1920 1432 1710 1845 1945 2045 2289 1681 * Oversize ** Profile base frame with six holes for foundation bolts 25 Technical Data NK 1450 min (4-pole motors) Common With Standard Coupling With Spacer Coupling Motor [mm] [mm] Type Motor Weight [kW] Size a a h L h h L L b b d [kg] L h h L[mm]L b b d Weight [kg] -1 2 55 75 90 110 132 300-360 * 2 3 1 3 2 3 3 250M 2007 2200 1900 280S 2032 2300 2000 280M 300 180 440 2082 180 700 860 795 22** 315S 2437 2400 2100 315M 1150 1310 1390 1690 1840 1 3 2 3 2287 2200 1900 2312 2300 2000 2362 180 700 860 795 22* 2712 2400 2100 1170 1330 1410 1710 1860 * Oversize ** Profile base frame with six holes for foundation bolts Motor Common Type Motor [kW] Size a [mm] a h 2 100-200 125-250 150-315 200-400 * 200-500 * 250-310 * 250-330 * 250-400 * 250-500 * 300-360 * 1.5 2.2 3 4 2.2 3 4 5.5 7.5 5.5 7.5 11 15 18.5 22 30 37 30 37 45 55 75 11 15 18.5 18.5 22 30 18.5 22 30 37 45 55 45 55 75 90 110 22 30 37 45 55 * Oversize 26 100L 112M 132S 132M 112M 132S 132M1 132M2 160M 132M 160M 160L 180L 200L1 200L2 225M 250M 225M 250M 280S 280M 280M 160L 180L 200L1 200L1 200L2 225M 200L1 200L2 225M 250M 280S 280M 280S 280M 315S 315M 315L1 200L2 225M 250M 280S 280M 2 125 90 280 970 min (6-poled motors) With Standard Coupling With Spacer Coupling [mm] [mm] Weight Weight L h h L L b b d [kg] L h h L L b b d [kg] -1 3 945 967 1 3 2 3 3 170 182 1085 1107 1077 200 1217 967 232 250 260 271 306 395 420 460 527 751 781 827 948 960 1080 1205 1265 1272 560 600 625 800 830 874 814 844 890 1017 1150 1208 1240 1300 1700 1827 1897 991 1042 1165 1294 1353 1107 80 280 1120 140 90 355 1077 80 330 1250 740 490 440 24 840 540 490 24 1187 160 110 400 1275 1600 1060 660 600 100 380 28 1320 1390 1800 1200 730 670 1712 180 200 400 100 500 1800 1200 730 670 28 1797 1877 1869 1900 1600 1949 160 480 885 250 175 675 1902 945 18 2000 1700 1952 180 490 880 1487 250 200 400 1557 140 480 1700 1400 950 890 18 1597 250 225 400 1772 120 570 2000 1340 910 830 28 1857 1722 160 470 1807 200 175 600 1887 1912 180 480 1962 2022 490 2072 180 300 175 660 495 2427 200 515 1800 1500 790 850 18 1900 1600 2000 1700 2000 1700 780 945 880 18 2200 1900 955 875 1842 1800 1500 1927 1900 1600 300 180 440 2207 180 530 860 795 18 2032 2000 1700 2082 1 3 2 3 1120 740 490 440 1250 840 540 490 80 280 24 212 80 330 1250 840 540 490 24 1327 100 350 1400 940 610 550 28 1217 1415 1600 1060 660 600 100 380 28 1460 1530 1800 1200 730 670 1912 100 500 1800 1200 730 670 1997 120 520 2000 1340 910 2059 2077 2000 1700 2149 160 480 2102 945 2100 1800 2152 180 490 1687 1700 1400 1757 140 480 950 1797 1800 1500 1972 28 830 885 18 880 890 18 120 570 2000 1340 910 830 28 2057 1922 160 470 2007 2087 2112 180 480 2162 2222 490 2272 180 495 2627 200 515 1900 1600 2000 1700 2100 1800 790 850 170 182 18 780 2200 1900 945 880 18 2400 2100 955 875 2122 2000 1700 2207 2287 180 530 2100 1800 860 795 18 2312 2362 2200 1900 232 250 260 271 324 395 420 460 527 750 780 848 968 960 1085 1220 1278 1285 560 600 640 800 830 874 818 848 900 1075 1229 1288 1255 1315 1715 1842 1912 1000 1100 1210 1330 1400 Technical Data NK Quotation Drawing Quotation Drawings NK 32-125 -> 150-400 27 Technical Data Quotation Drawing "Oversizes" NK 150-315, 200-500, 250-400, 250-500 28 NK Technical Data NK Quotation Drawing "Oversizes" NK 200-400, 250-330, 300-360 29 Technical Data Quotation Drawing "Oversizes" NK 250-310 30 NK