LED Outdoor Canopy Luminaires
Flush Mount
LCN3 Series
EnduraLux ™
This procedure is designed as an installation aid. Skilled trades people that are familiar
with general construction and electrical installation techniques should perform the
installation. Licensed electricians should provide electrical installation connections.
Installations and connections should be done in accordance with all national and local
codes and permits. In no way is this document intended to construe warranty or fitness
of use of the products described, nor is it intended to provide safety instruction for those
installing the product.
WARNING
Before proceeding with installation or service maintenance of this product:
• Disconnect power to reduce electrical shock risk.
• Review the entire Installation Guide.
• Inspect this properly packaged product for any damage that may have occurred during transit.
• Verify product application complies with manufacturer design recommendations.
• Verify the availability of necessary tools and incidental material.
• Verify applicable code requirements. Field assembly and installation are subject to acceptance by
local inspection authority.
• Appropriate safety equipment to be determined by end user, per applicable safety standards and
precautions.
LCN3 Series Installation Guide – Page 1 of 4
Installation Guide
Canopy Deck
Part
#
Part Name
Qty.
1
Fixture Housing
1
2
Mounting Studs
4
3
Lower Housing Gasket
1
4
Fixture Wiring Assembly
1
5
Lower Canopy Plate
1
6
Above Canopy Gasket
1
7
Upper Canopy Plate
1
8
Gasket Washers
4
9
Cap Nuts
4
10
Aluminum Tube (Shown
with included hex nut
attached.)
1
11
Junction Box
1
12
Hole Plugs (AC Input Hole)
2
13
Hex Nut (For Junction Box)
1
14
Junction Box Cover
1
15
Power Supply Quick
Connector/Wiring Assembly
1
16
Screws (For Junction Box
Cover)
2
LCN3 Canopy Luminaire Installation
A
Fig. 1
Step 1 - Open the carton and remove the top foam layer. Lay the
fixture, with the glass face down, on top of the foam layer, to
prevent damage to the finish. In Fig. 1, the back of the fixture
housing is visible, A showing integral mounting studs and gasketing
around center threaded entry.
LCN3 Series Installation Guide – Page 2 of 4
LCN3 Canopy Luminaire Content Details
B
Step 2 - Remove mounting hardware from box B . With fixture
facing glass down on the foam sheet, feed the wiring assembly
through the center hole of the lower canopy plate C , then place
plate over the four studs and threaded entry.
Fig. 2
C
Step 3 - For new construction, drill five holes with the included
drilling template, or cut a 4” diameter hole into the canopy deck
surface.
For retrofit into 4” diameter hole from underneath the canopy,
position the studs through the 4” diameter canopy hole D and
secure the fixture housing into position against the canopy, aligning
the fixture below the canopy square with canopy joints.
D
Step 4 - Apply room temperature silicone vulcanizing (RTV) sealant
around the 4” hole, then place the round gasket over the 4 studs E
and apply more silicone RTV sealant on top of the gasket.
E
Fig. 4
F
G
H
I
Step 5 - While supporting fixture housing from below, place the
upper canopy plate F over the studs and threaded coupling G .
Install washers with rubber gasket facing down H and then finger
tighten the cap nuts I . Securely tighten the cap nuts to provide a
secure seal.
Fig. 5
J
K
Fig. 6
Step 6 - From the back of the fixture housing, feed the wiring
assembly through the aluminum tube, gasket end down J , then
screw the aluminum tube into the threaded coupling K , and hand
tighten.
LCN3 Series Installation Guide – Page 3 of 4
Fig. 3
L
Step 7 - Feed the wiring assembly through the aluminum tube L
and screw gasket end onto the threaded nipple and tighten.
Fig. 7
M
Step 8 - Remove the top cover of junction box. Feed the wiring
assembly through the opening in the bottom of the junction box M ,
then screw the remaining hex nut N onto the threaded aluminum
tube. Position box for conduit entry, and securely tighten hex nut.
N
Fig. 8
Step 9 - Attach the junction box cover to the side of the junction
box. O Connect the fixture housing DC wiring assembly to the
P power supply quick-connector(s). P
Note: Some LCN3 models may have 2 power supplies and 2 wiring
assemblies.
Fig. 9
Q
Step 10 - Mount the supply wiring conduit to the junction box Q
using a liquid-tite connector. Connect the supply wiring to the AC
input wiring on R the power supply(ies).
R
Fig. 10
Step 11 - Mount the cover of the junction box onto the lower
housing and securely tighten screws. S Installation complete.
S
Fig. 11
Please visit Leotek Electronics USA Corp. at www.leotek.com
V8-092413 | Information provided subject to change without notice.
LCN3 Series Installation Guide – Page 4 of 4
O