Medium Voltage
Soft Starters
SAP6000 Soft Starters
The SAP6000 SS is designed to operate with standard asynchronous motors. The digital control
methods provide smooth acceleration, greatly extending the life of medium voltage motors. Our Soft
Starters offer ruggedness and high thermal capacity, where other Soft Starters may be limited, to
ensure a faulty-free life service.
Sedecal Control offers a wide range of Soft Starter Options by manufacturing a product that is tailored
to the specific needs of the client.
Previous to the manufacturing phase knowledge about the motor to be started is necessary. Common
required data are application of the motor (compressor, fan, pump...), motor rated power, nominal
current, nominal voltage, speed, line frequency, motor torque vs speed, motor current vs speed,
altitude, ambient temperature or humidity. Useful information also includes the curve of the load torque,
starting/stopping times profile and general plant electrical power distribution. Big fans need around 60
seconds to start and pumps around 20s.
Main Specs
High Thermal Capacity
Tailored design
Fiber Optic controlled Thyristors
Easy setup and operation
Isolation between MV and LV parts
Affordable Spare Parts
Communication modules, CANOpen, Profibus, Profi-Bus, Modbus, RS485, Ethernet...
Heavy Duty design
High power stack module
Industries
Applications
Centrifugal Pumps
Pulp Mills
Centrifugal Blowers
Conveyor Systems
Water Pumps
Desalination Pumps
Gas Compressors (HP, LP)
Oil and Gas
Construction
Mining
Metallurgical
Marine
Industry
Water
Chemical
Sample Designs
Multi Motor Starting configuration
Specifications
SAP6000 Soft Starter
Nominal Voltage
2300V to 13800V
Power
250kW to 10MW
Frequency
50-60Hz
Up to 10 starts/hour
Capacity
3 consecutive starts allowed
Control Voltage
Rated Insulation Voltage
Continuous Overload
Overload for 60s
48Vdc, 380Vac (3F), 220Vdc,
110Vdc-220Vac
3.6kV-17.5kV
1.2 In
4 In
Thyristor gate isolation
Fiber Optic
Impulse withstand voltage
40kV-95kV
Motor Overload electronic protection
Bypass vacuum contactor
Programmable IEC255-8
Included
Underload detection
Programmable
Start/Stop sequences per hour
Programmable
Voltage dip protection delay
Programmable
Standard protections
Overcurrent-Phase loss-Phase
reverse -Heatsinks over tempsemiconductor short circuit
Start/Stop
Local and Remote
Emergency Stop
Local and Remote
4-20mA (0-10V) motor current output
Included
Output Busbars
Included
Input Busbars
Included
Operating Temperature
-10C..+40C
Motor Protection Relay
Optional
Mechanical interlocks
Optional
Specifications
SAP6000 Soft Starter
Input Cabinet
Optional
Input vacuum contactor
Optional
Energy Analyzer, Pt100 and PTC controllers
Optional
Comm. modules Profinet, Profibus, RS485, RS232,
CAN, MODBUS
Insulating Varnish coated electronics
Cooling system
As requested
Included
natural convection/forced air
Anti condensation heater
Included
Lifting ringbolts
Included
Standard interface signals
Fault-Running-Motor overloadbypass open/close-active-End of
start
6.6 kV Soft Starter general dimensions (1500x1200x2300).
May change depending on final requirements.
About Sedecal Control
Sedecal Control SA was founded in 1995 and started with the design and manufacture of medium
and high power Soft Starters, frequency converters and power systems for different applications in
the field of heavy industries. After time, power modules for solar and wind applications were included
in the product line. Sedecal Control will soon offer a medium voltage VFD (Variable Frequency Drive)
to meet the needs of different industries and applications.
Sedecal Control belongs to the Sedecal Group which is a worldwide referent mainly dedicated to the
manufacture and design of X-Ray equipment for the medical and veterinary sectors.
Voltage
Sedecal Control
Pelaya 9
28110-Algete-Madrid-Spain
contact@sedecal-control.com
A Sedecal Group Company
Medium Voltage Soft
Starters
Medium Voltage Variable
Frequency Drives ✪
Low Voltage modules/
converters for Solar/Wind
Low Voltage Variable
Frequency Drives ✪
Power
Sedecal Control Product Line-up
✪ In development