HLM35V8E / HLD35V8E
Manual Iris and DC-Type Auto Iris Varifocal Lenses
INTRODUCTION
Verify lens type and camera type before following installation instructions.
DC-Type Auto Iris Mechanism: This lens does not have a built-in amplifier for auto-iris control. The DC
voltage from the camera operates the iris of the lens. This lens can only be used in combination with a camera
that has a built-in auto iris amplifier (DC-iris) or a camera that is switchable between video signal and DC-iris.
Varifocal Lens: With a varifocal lens type, a variable focal distance enables different fields of view (zoom)
with the same lens. After adjusting focal length, it is necessary to readjust the focus. This may also include
resetting the backfocus.
CABLE CONNECTION OF LENS CONNECTOR
All Honeywell Video Systems auto
iris lenses are equipped with a
standard 4-pin connector to easily
connect to Honeywell Video
Systems cameras.
F.5
Connector
Cover
Pin 3
Pin 1
Pin 4
If your camera does not support this
standard or connector repairs are
required, refer to Figure 1 for
proper wire terminations for these
lenses. If a bad connection occurs,
both the lens and camera may
malfunction and fail. Follow the
diagram and table in Figure 1
carefully.
Pin 2
Solder and
heatshrink
connections
Iris Control
Cable
Connector
Damp Coil “+” (~700 Ohm)
Damp Coil “-”
Drive Coil “+” (~200 Ohm)
Drive Coil “-”
Figure 1: Lens Connector Cable Connection
ATTACHING THE LENS TO THE CAMERA
Prior to attaching the lens to the camera,
1.
Switch the AUTO IRIS lens type switch on your
camera, if so equipped, to the DC position.
2.
Set the electronic iris (EI) OFF.
To attach the lens to the camera, turn the lens clockwise on
the lens mount until it reaches the end travel. If the
orientation of the lens is inconvenient because of the cable,
the lens may be turned to the proper position by continuing
in the clockwise direction. The lens clutch will allow
approximately one additional revolution. Plug the auto iris
connector into the camera.
Rev. A
1
Figure 2: Attaching the Lens
HLMU000838
10/28/03
BACKFOCUS ADJUSTMENT
Although the camera backfocus was adjusted by the manufacturer prior to shipping, it may be necessary to
make modifications. For best results, perform backfocus adjustments at night or while using a #6 or #8
welder’s glass in front of the lens. The focus of the camera will change slightly if the camera iris was adjusted
on a light scene and then changes to a dark scene. However, the camera will remain in focus if the iris was
focused on a dark scene and the scene lightens. To make backfocus adjustments, perform the following:
1.
Mount the lens on the camera and apply power.
2.
Open the camera iris by turning the lens level control counterclockwise.
3.
If a picture is visible, focus on the scene. Open the lens as wide as possible by placing a welder’s
glass in front of the lens.
4.
When the iris is open to the widest point, readjust the focus for a clear picture.
If a clear picture is not visible, set the focus ring to mid-range.
5.
Loosen the backfocus lock screw.
6.
Adjust the backfocus ring for a clear picture.
7.
Tighten the backfocus screw lock.
8.
Fine-tune the focus with the focus ring on the lens.
9.
Remove the welder’s glass from in front of the lens.
10. Adjust the level control of the lens for the best picture quality.
LENS SPECIFICATIONS
Image Format
1/3” ~ 1/4"
Focal Length
3.5 ~ 8.0mm
Maximum Aperture Ratio
1:1.4-1.96
Zoom Ratio
2.3X
Iris
Control
Method
HLM35V8E:
Manual
HLD35V8E:
Direct Drive
Iris
Range
HLM35V8E:
F1.4 (1.96)~Close
HLD35V8E:
F1.4 (1.96)~360
Focus
Manual
Zoom
Angle Field of
View (D × H × V)
Manual
1/4 inch
Wide:
69.6.5" × 56.5" × 42.7"
Tele:
32.8" × 26.3" × 19.8"
1/3 inch
Wide:
88.5" × 73.8" × 56.5"
Tele:
43.5" × 35.0" × 26.3"
Minimum Object Distance
0.3m
Back Focal Length
8.64~14.16mm
Effective Diameter
ø 21.5mm
Rear:
ø 8.0mm
Mount/Flange Back
CS/12.5mm
Mechanical Dimensions
(D × (H) × L)
HLM35V8E:
ø37.6mm × 48.1mm
HLD35V8E:
ø36mm × 47.1mm × 48.1mm
Weight
Temperature Range
Rev. A
Front:
HLM35V8E:
89.8g
HLD35V8E:
76.6g
+14°F ~ +122°F (-10°C ~ +50°C)
2
HLMU000838
10/28/03