POWER QUALITY PRODUCTS
FOR NON-LINEAR LOADS

SECTION 6 POWER QUALITY PRODUCTS
FOR NON-LINEAR LOADS
Power Quality
E
P
r
P
Q
More and more, electricity is being considered as a product. Ideally, the AC voltage wave is a sine wave alternating from a positive peak to a negative peak 60 times per second (60 Hz) without any deformations, spikes or surges. In reality, different factors influence the quality of the wave. Certain disturbances come directly from the power source, such as lighting. Other disturbances come from loads; in particular, from electronic equipment which are non-linear loads that produce harmonics, due to their switching power supplies.
As a result of voltage fluctuations as well as economic considerations, the non-linear power supply known as the switching power supply, was developed by computer manufacturers. Power conversion is no longer accomplished at 60 Hz AC-DC conversion is accomplished by a converter, which operates in the 20-100 kHz range.
Personal computers, workstations, local networks and other accessories that use these power supplies or this technology are very sensitive to problems caused by electric energy. Electrical issues can cause many problems on linear loads and other devices such as transformers, motors, circuit breakers, fuses, etc. Meanwhile, other hidden electric problems are caused by voltage spikes, voltage surges, brownouts, as well as by electric noise on the lines and can bring about different consequences.
Voltage Spikes arise when equipment, which operates on high current is turned off, such as air condition ers, photocopiers, coffee makers, electric tools etc. These spikes, while brief, can destroy data stored on disk or on magnetic tape, modify memory and even cause serious damage to equipment (example: the breaking of a disk drive’s reading head).
Electric Noise is usually the worst of these problems because we cannot detect it without specialized instruments
(e.g. recording device, oscilloscope, etc.). Noise can interfere with data signals by causing data transmission errors between the many components of a system. Certain noise in the high frequencies can even travel through circuit paths and destroy integrated circuits.
Electric noise can be generated from any temporary high frequency (harmonic from 50 kHz to 100 MHz), from a radio frequency (RFI) or from the production of electromagnetic interference (EMI) emitted from transformers or motors (often an elevator motor or a motor from a photocopier). As well, magnetic fields, induced by a mono-phased cable or by an unbalanced three-phased system, can deform images on a cathodic screen (computer monitor) or destroy data on a hard disk.
There are two types of transient noise. The normal mode or transverse is due to an induced voltage between any two phase conductors (line-line). This voltage is normally in the low frequency range and causes damage to personal computers, local networks, and workstations. The common mode is due to an induced voltage between any phase conductor, including the neutral and the ground. This voltage can cause more damage than normal mode noise, not necessarily by its presence (2-3 V) but by the induce fluctuation that it produces. The common mode voltage is also produced by the presence of current on the neutral (E=IZ) and also because of the non-cancellation of the triplen on the phases that adds up on the neutral. Consequently, common mode voltage produces ground potential differences with other grounds.
Non-linear loads (computers, variable speed drives, etc.) generate Harmonics . Harmonics produce an increase in the resistance of the conductor (skin effect) and, in turn, an abnormal common mode (neutral-ground) voltage difference. This will cause undesirable ground loops to occur. To save energy or to transform an alternating current into a direct current, their power source takes its current as portions of the 60 Hz sine wave. In doing so, the portions of the sine wave that the power supplies do and don’t take causes the sine wave to become deformed and multiple frequencies of 60 Hz are formed. Often, single phase loads produce triplets (3 rd , 9 th , etc.), while three phase loads produce 5 th and 7 th harmonics. Therefore, electric equipment and installations which are designed to operate at 60 Hz, can become damaged or unbalanced due to these harmonic frequencies which are different than the
138
Data subject to change without notice.

SECTION 6 POWER QUALITY PRODUCTS
FOR NON-LINEAR LOADS fundamental (60 Hz). The principal problem that arises is the overheating of equipment or conductors. The harmonic distortion rate (HDR) is the ratio between the harmonics and the fundamental load expressed as a percentage.
Voltage surges can be compared to voltage spikes, except they last longer, from 15 microseconds to half a second or more. They are mainly caused by the shutdown of heavily loaded circuits or by the necessary commutation of a high-powered network (eg. Pf correction). Computers and other sensitive electronic equipment can seriously be damaged by such an over-voltage surge. Voltage surges which exceed normal voltages by 20%, affect numeric data, produce reading errors on verification systems and damage equipment. Temporal fluctuations produce parity errors and interrupts protection systems.
Voltage sags are normally caused by the addition of heavy loads on an electric line such as the start-up of an elevator, photocopier or large motor. In this case, the current undergoes a loss of 20% or more for a period of
15 microseconds to half a second.
Brownouts last longer than voltage sags. Brownouts are sometimes caused intentionally by the power company to avoid a total blackout when there is a great demand for electricity. They often lead to losses and even unresolved errors concerning central memory data or when data is being stored on disk or magnetic tape. In certain cases, if the brownout last long enough, it can cause an automatic shutdown of certain equipment.
Flickering is a voltage variation with a lighting load that causes the light output to visibly flicker. This can be caused by the input in function of electro-domestic loads however, it is mostly due to industrial loads (eg. Motor start up or speed variation)
Blackouts can last from a few microseconds to many hours or even days. These total losses of current normally occur due to damaged equipment or electric lines.
E
P
n
-l
E
s
A switching power supply takes a portion of the maximum positive energy as well as the minimum negative energy on the sine wave. This deforms the sine wave, provoking a new wave. Fourier, the French mathematician, demonstrated that this new wave can be broken down as the sum of many waves (harmonics), for which the fundamental is at 60 Hz, and of all the present harmonics, the 2 nd at 120 Hz, the 3 rd at 180 Hz, etc.
A spectral analysis gives us the amplitude of these waves and allows us to compare the relative importance of each of these.
Harmonics can cause fuses and circuit breakers to open a circuit for no apparent reason. An installation capable of supporting a certain amount of linear loads could no longer be able to support it after being replaced with nonlinear loads of the same power at 60 Hz. We should be seeing a rapid progression of this type of problem as new non-linear harmonic loads are added or replace traditional linear loads.
With energy saving programs, utilities lead their customers to use switching power supply technology such as variable speed drives and electronic ballast.
The laws of electricity have not changed but our knowledge of them becomes essential:
• The more the frequency increases, the more the metal becomes resistant (skin effect).
• Certain harmonics are at direct sequences (1, 4, 7, 10), others inverse (2, 5, 8, 11), and others without sequence are called triplets (3, 6, 9).
• Harmonics can damage transformers.
• Inverse harmonics have harmful effect on motors.
• Harmonics influence the power factor.
139
Data subject to change without notice.

SECTION 6 POWER QUALITY PRODUCTS
FOR NON-LINEAR LOADS
In a factory, if we find a certain amount of current harmonics, is there a problem?
Ohm’s law (V=IR) with a few exceptions, explains the consequences of these harmonics on inductive and resistive loads. Current distortions will create voltage distortions according to the line impedance. It is well known that for any non-linear load installation, it is very important that the impedance be as low as possible. One should always foresee the consequences of a current distortion on voltage or on the harmonic voltage distortion that it can bring about. Current harmonics are always present in non-linear loads and if they are properly dealt with, they will not always be problem sources.
P
E
d
s
Voltage Regulating Transformers (Computer Regulator)
As well as insuring protection against spikes and surges, voltage regulators filter most of the electric noise which is often a hidden source of problems. Voltage regulators are more expensive than peak cut-off circuits (TVSS), but they protect much better since most are equipped with an isolation transformer. There are three types of voltage regulators on the market: the ferro-resonant transformers, tap switching transformers and the electronic voltage regulator.
Single-phase Line Conditioning Transformers (Line Voltage Conditioner)
Isolation transformers are sometimes equipped with peak cut-off circuits and filters and they can have a galvanic isolation. They therefore become great line conditioners, protecting against noise and spikes.
Isolated Delta-Star Transformers (Super Isolation Transformer)
This type of transformer is very popular. They cost less and can also isolate the application from the line.
Peak cut-off circuits, filters and a double electrostatic shield can be added as options for protection against common mode noise and voltage spikes found on the line (for information on harmonics, see K-type, Delta-Wye for Non-linear
Loads ).
Because of the galvanic isolation, there will be a link on the secondary between the neutral and the ground which eliminates the possible voltage between the neutral and the ground on the secondary of the transformer. To be more efficient, these transformers must, if possible, be installed close to the application.
Since standard transformers were built to support linear loads, they may overheat and become damaged with non-linear loads.
Harmonic Mitigating Transformer (0° or -30° primary-secondary Phase Shift) (refer to Section 8, page 199)
Even if it is possible with a K-type transformer, depending on the quantity of Zero Sequence harmonics (triplets), to support non-linear loads, how can one know which loads will be applied in 6 months, 1 year, or more?
Special interconnections secondary construction produces a cancellation of the 3 rd , 9 th , 15 th harmonics (triplets).
So, if we build a transformer with a Delta primary and a double interconnected winding secondary to cancel triplen
(zero sequence harmonics), we will have:
• An adaptable transformer for non-linear loads
• A low-impedance cancellation of the 3 rd , 9 th , 15 th harmonics
• A better equilibrium of phases and less harmonic voltage distortion (low-impedance Zero Sequence).
An electrostatic screen and a peak cut-off filter could also be installed for additional protection against common mode noise. The installation of this kind of transformer is the same as for an ordinary transformer. Many existing applications use this type of construction.
Because of its phase shifting of 0°, it should be noted that by placing this type of transformer in a system composed of already existent Delta-Star transformers (-30º), a cancellation of the 5 th and 7 th harmonics will be
140
Data subject to change without notice.

SECTION 6 POWER QUALITY PRODUCTS
FOR NON-LINEAR LOADS obtained. The 5 th and 7 th harmonics from the transformers will try to cancel the 5 th and 7 th harmonics coming from the already existent Delta-Star transformers (-30º). This will also improve the power factor.
Harmonic Mitigation Transformer Dual Output (-15°, -45º or 0º, -30° between the secondary double windings dual output)
(refer to Section 8, page 199)
This is a transformer with three phases on the primary and six on the secondary, so two sets of three phase outputs on the secondary. Because of the phase shifting between the two sets of three phase outputs:
• A cancellation of the 3 rd , 5 th , 7 th , 9 th , 15 th , 17 th and other harmonics like the 19
0º and –30º angle difference and low impedance.
• An improvement in the equilibrium of the phases.
• A cancellation of triplets with only a difference of 0º and –60º.
th on the secondary with a
• A cancellation of the 5 th , 7 th , 17th and 19 th harmonics with an angle difference of -15º and -45º and the
triplets are trapped in the Delta winding.
• An important power factor improvement.
Typical and General Construction for a Transformer in a Demanding Environment with Non-linear Loads
Coil connections should be Delta on the primary and Star on the secondary. Even better, use double windings on the secondary which would diminish harmonic voltage distortions caused by current distortions (V=IR); this type of winding cancels triplets (3 rd , 9 th on the secondary) at very low impedance.
The K-factor value should be well established with respect to the anticipated loads; for example, K13 can take up to 33% of the fundamental in the 3 rd harmonic, 20% in the 5 th , 14% in the 7 th , and 11% in the 9 th .
A high performance grounded electrostatic shield may also need to be installed. As well, peak cut-off circuits and hybrid filters can be installed to make the transformer more efficient in protecting the loads in question.
Uninterruptible Power Supplies
These units isolate line to load at all times and are installed between the line and the load. They constantly provide power to keep equipment working (computers, servers, terminals, PLCs, etc.). In a blackout situation, they output a perfect sine wave without any transfer time or interruption.
P
f
Power Factor is the ratio between the apparent power (VA) and the real power (W). Energy suppliers deliver electricity with a sine voltage wave at 60 Hz. If the current and voltage waves are not aligned, the system’s efficiency is diminished and the apparent power is greater than the real power. In an inductive system, the voltage wave is ahead of the current wave. In a capacitive system, it is the current sine wave that is ahead of the voltage sine wave.
In order to compensate for the inductive effect of motors, correction is achieved using capacitors to align the two waveforms.
There are now two causes that contribute to the deterioration of the power factor: inductive loads, which influence the displacement power factor, and non-linear loads when the current harmonics are not aligned with the voltage source. Total power factor which the utilities measure considers both of these causes.
Knowing the cause for the deterioration of the power factor will help to choose the best way to correct it. In some cases, correcting harmonic problems can rectify the power factor.
141
Data subject to change without notice.

SECTION 6 POWER QUALITY PRODUCTS
FOR NON-LINEAR LOADS
Power Quality Solutions
The solutions are as wide ranging as the problems. We have summarized some solutions in the table below.
HPS SOLUTIONS
Voltage Regulators
Line Voltage Conditioners
Super Isolation Transformers
Harmonic Mitigating Transformer
(refer to Section 8, page 199)
POWER QUALITY PROBLEM
Industrial control malfunctions, frequent voltage swings, up to 2 kVA.
Computers, controls freezing or power supply frequent failure, common mode voltages, up to 5kVA.
Control room failure, freezing of
Industrial control, common mode voltages, electrical noise.
Voltage distortion, non-linear load current distortions, short computer lives, poor total power factor.
GENERAL USAGE
Industrial Automation Control, Small Computer
Application. Single Phase Applications.
Industrial PLC Application, Basic Computer
Protection. Single Phase Applications.
Industrial Control Room, Hospital Equipment.
Standard Non-Linear Load Applications, Harmonic
Cancellations, Building Design w/ Energy Saving,
Total Power Factor Correction.
Voltage Regulators protect equipment from both noise and voltage fluctuations. They are an inexpensive solution, available in both portable or hard-wired models. They provide ideal protection in high noise areas where voltage fluctuations exceed the regulating range of the computers power supply.
Line Voltage Conditioners are isolation transformers equipped with peak cut-off circuits and filters and therefore become great line conditioners protecting equipment against noise and voltage spikes.
Super Isolation Transformers provide inexpensive protection against frequency variation or noise related disturbances. This is adequate where voltage fluctuations are not a serious problem. Most high-end computers have built-in voltage regulation, but still require protection from line noise.
Energy Efficient Harmonic Mitigating Transformers with zero sequence flux cancellation technology, provide total protection against all harmonics generated by computer equipment and other non-linear and power electronic loads (refer to Section 8, page 199).
142
Data subject to change without notice.

SECTION 6 POWER QUALITY PRODUCTS
FOR NON-LINEAR LOADS
Portable Voltage Regulators are easily moved from place-to-place and attractively finished to adapt to any workplace. They provide ideal protection in high noise areas where voltage fluctuations exceed the regulating range of the equipment/system power supply. Epoxy potted windings are impervious to mois ture from accidental spills. This makes them ideal for use between any wall outlet and your equipment.
• Protects equipment from both noise and voltage fluctuations
• Windings impervious to moisture
• Rejects Noise
• Controls voltage fluctuations
• UL and CSA Listed
• Attractively finished in brown and beige
The voltage regulator is a ferroresonant transformer type regulator with a simple circuit configuration and has no moving components. This provides fast response, automatic output current limiting and high reliability.
• Instrumentation
• Data terminals
• Micro processors
• Instrumentation
• CAD/CAM systems
• Security systems
• Test equipment
• Navigation equipment
• Electronic cash registers
• Communications equip.
• Medical Diagnostics equip.
• Photographic equip.
• Programmable controllers
• Scientific research equip.
• Mini/micro computers
Input voltage range +/- 15%
Output regulation/response time +/- 3%/1.5 cycles
Frequency input range
Harmonic Distortion
59-61 Hz/49-51 Hz*
3%
Common mode rejection
Normal mode rejection
Audible noise
Efficiency
Holdup time
120 dB
60 dB
43 dBa
85%
3 ms.
* = 50 Hz Models
A
B
C
120V OUTPUT
Power
Rating
VA
70
140
250
500
750
1000
1500
2000
Input
Range
VAC
95-130
95-130
95-130
95-130
95-130
95-130
95-130
95-130
Catalog
Number
CV70AFP
CV140AFP
CV250AFP
CV500AFP
CV750AFP
CV1000AFP
CV1500AFP
CV2000AFP
5.13
5.13
7.13
7.13
9.25
9.25
11.5
11.5
8.63
8.63
10.63
10.63
12.63
12.63
15.0
17.0
Approx. Dimensions (inches)
Width
A
Depth
B
Height
C
5.38
5.38
7.25
7.25
9.75
9.75
9.0
10.25
60 Hz
Approx.
Weight
(Lbs.)
Note: For 220V/50 Hz models, please contact our quotations department for specifications and delivery.
23.0
23.0
45.0
55.0
95.0
100.0
120.0
140.0
143
Data subject to change without notice.

SECTION 6 POWER QUALITY PRODUCTS
FOR NON-LINEAR LOADS
Hard Wired Line Voltage Conditioners are designed to be installed directly to the utility power source to provide dedicated clean power to one or more outlets (depending on the unit size), for a variety of equipment. They provide ideal protection in high “noise” areas where voltage fluctuations exceed the regulating range of the equipment/system power supply. Epoxy potted windings protect against mois ture, dust and other airborne contaminants and are ideal for office or plant locations.
Input voltage range +/- 15%
Output regulation/response time +/- 3%/1.5 cycles
Frequency input range (60 Hz models) 59-61 Hz
Harmonic Distortion 3%
Common mode rejection
Normal mode rejection
Audible noise
Efficiency
Holdup time
120 dB
60 dB
55 dBa
85%
3 ms.
* Not intended for “Highly Inductive Loads”
The Line Voltage Conditioner is a ferroresonant transformer type regulator with a simple circuit configuration and without moving components. This provides fast, responsive voltage regulation.
CAD/CAM systems, medical equipment, security systems, test equipment, navigation equipment, data terminals, scientific equipment, communications equip ment.
120/240V OUTPUT
Input
Range
VAC
Catalog
Number
Case
Style
(Page 246)
Power
Rating
VA
250
250
250
500
500
500
750
750
750
1000
1000
1000
1500
1500
1500
2000
2000
2000
3000
3000
3000
5000
5000
5000
120/208/240
240/480
600
120/208/240
240/480
600
120/208/240
240/480
600
120/208/240
240/480
600
120/208/240
240/480
600
120/208/240
240/480
600
120/208/240
240/480
600
120/208/240
240/480
600
CVHW250C
CVHW250D
CVHW250E
CVHW500C
CVHW500D
CVHW500E
CVHW750C
CVHW750D
CVHW750E
CVHW1000C
CVHW1000D
CVHW1000E
CVHW1500C
CVHW1500D
CVHW1500E
CVHW2000C
CVHW2000D
CVHW2000E
CVHW3000C
CVHW3000D
CVHW3000E
CVHW5000C
CVHW5000D
CVHW5000E
L11
L11
L11
L12
L12
L12
L9
L9
L9
L10
L10
L10
L13
L13
L13
L6
L6
L6
L7
L7
L7
L8
L8
L8
Approx. Dimensions
Width
(Inches)
Depth Height
6.75
6.75
6.75
6.75
6.75
6.75
9.00
9.00
9.00
9.00
9.00
9.00
11.50
11.50
11.50
11.50
11.50
11.50
13.00
13.00
13.00
15.00
15.00
15.00
4.75
4.75
4.75
6.25
6.25
6.25
7.25
7.25
7.25
8.50
8.50
8.50
7.50
7.50
7.50
9.00
9.00
9.00
12.00
12.00
12.00
12.00
12.00
12.00
14.30
14.30
14.30
14.30
14.30
14.30
17.25
17.25
17.25
18.25
18.25
18.25
20.75
20.75
20.75
20.75
20.75
20.75
20.50
20.50
20.50
25.00
25.00
25.00
60 Hz
Approx.
Weight
(Lbs.)
158
158
158
225
225
225
95
95
95
130
130
130
325
325
325
32
32
32
43
43
43
80
80
80
144
Data subject to change without notice.

SECTION 6 POWER QUALITY PRODUCTS
FOR NON-LINEAR LOADS
• Clean, noise-free power output
• Low coupling capacitance
• Attractively finished in brown and beige
• CSA Certified
Super Isolators are shielded transformers with a simple circuit configuration and no moving compo nents. This provides fast response, automatic out-put current limiting and high reliability with complete isolation from the power line. All units are hard wired.
In many applications, a super Isolation
Transformer will provide all the protection you need.
This applies in areas where noise is a problem, but voltage fluctuation is not. For example: shopping malls, high rise complexes, airports, densely populated residential areas, etc.
Super Isolators are also ideal for noise suppression for equipment having its own internal voltage regulation provided by the use of a switching power supply. Examples are: computers, life support systems, security systems and navigation systems.
Common mode rejection................................. 146 dB
Transverse mode rejection................. Typically 60 dB
Operating voltages.................. up to 110% of nominal
Dielectric strength....................... 2500 VAC minimum
Frequency input range...... 47-63Hz for 50/60Hz units
........................................... 57-63Hz for 60Hz units
DC Isolation 1000 megohms input to output and
circuit to ground.
A B
C
D
E
F
A B
145
D
E
C
F
0.50 DIA.
Data subject to change without notice.

SECTION 6 POWER QUALITY PRODUCTS
FOR NON-LINEAR LOADS
kVA
Rating
0.12
0.12
0.25
0.25
0.5
0.5
1
1
5
5
10
10
2.5
2.5
5
5
15
15
20
20
10
10
15
15
20
20
Catalog
Number
US10121
UT10121
US10251
UT10251
US10501
UT10501
US11001
UT11001
US12501
UT12501
US15001
UT15001
US15004
UT15006
US110001
UT110001
US110004
UT110006
US115001
UT115001
US115004
UT115006
US120001
UT120001
US120004
UT120006
Frequency
Hz
50/60
60
50/60
60
50/60
60
50/60
60
50/60
60
50/60
60
50/60
60
50/60
60
50/60
60
50/60
60
50/60
60
50/60
60
50/60
60
Input
VAC
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
240/480
600
120/240
120/240
240/480
600
120/240
120/240
240/480
600
120/240
120/240
240/480
600
Output
VAC
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
120/240
A
Overall Dimensions (inches)
B C D E F
6.63
6.63
9.63
9.63
9.63
9.63
9.63
9.63
5.13
5.13
5.13
5.13
6.63
6.63
6.63
6.63
7.63
7.63
9.63
9.63
8.13
8.13
9.63
9.63
13.63
13.63
12.63
12.63
12.63
12.63
19.13
19.13
6.13
6.13
6.13
6.13
7.13
7.13
7.13
7.13
7.13
7.13
9.88
9.88
9.88
9.88
9.88
9.88
3.66
3.66
3.66
3.66
5.11
5.11
5.11
5.11
5.11
5.11
8.11
8.11
8.11
8.11
8.11
8.11
4.66
4.66
4.66
4.66
6.11
6.11
6.11
6.11
6.11
6.11
9.11
9.11
9.11
9.11
9.11
9.11
9.63
9.63
19.13
19.13
9.88
9.88
8.11
8.11
9.11
9.11
16.63
16.63
13.25 21.56 12.38 11.73 12.73 19.06
13.25 21.56 12.38 11.73 12.73 19.06
13.25 21.56 12.38 11.73 12.73 19.06
13.25 21.56 12.38 11.73 12.73 19.06
13.25 21.56 12.38 11.73 12.73 19.06
13.25 21.56 12.38 11.73 12.73 19.06
13.25 21.56 12.38 11.73 12.73 19.06
13.25 21.56 12.38 11.73 12.73 19.06
11.13
11.13
10.13
10.13
10.13
10.13
16.63
16.63
5.13
5.13
7.13
7.13
5.63
5.63
7.13
7.13
Weight
Lbs.
86
75
138
120
138
120
225
225
27
23
44
38
12
10
18
16
225
225
325
280
325
280
375
325
375
325
kVA
Rating
7.5
15
15
15
15
22.5
22.5
22.5
3
3
3
3
7.5
7.5
7.5
45
45
75
75
75
30
30
30
45
Catalog
Number
US3031
UT3031
US3034
UT3036
US3071
UT3071
US3074
UT3076
US3151
UT3151
US3154
UT3156
UT3221
UT3224
UT3226
UT3301
UT3304
UT3306
UT3451
UT3454
UT3456
UT3751
UT3754
UT3756
Frequency
Hz
60
50/60
60
50/60
60
60
60
60
50/60
60
50/60
60
50/60
60
50/60
60
60
60
60
60
60
60
60
60
Input
VAC
208
208
240/480
600
208
208
240/480
600
208
208
240/480
600
208
240/480
600
208
240/480
600
208
240/480
600
208
240/480
600
Output
VAC
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
208Y120
146
A
28
28
28
28
25
28
28
28
25
25
25
25
25
25
25
37
37
37
37
37
28
28
28
37
30
30
30
30
27
30
30
30
27
27
27
27
27
27
27
38
38
38
38
38
30
30
30
38
Overall Dimensions (inches)
B C D E
20
20
20
20
19
20
20
20
19
19
19
19
19
19
19
28
28
28
28
28
20
20
20
28
21.5
24.5
24.5
24.5
24.5
24.5
24.5
24.5
21.5
21.5
21.5
21.5
21.5
21.5
21.5
24.5
24.5
24.5
33.5
33.5
33.5
33.5
33.5
33.5
27
27
27
27
24
27
27
27
24
24
24
24
24
24
24
36
36
36
36
36
27
27
27
36
F
13.5
14.5
14.5
14.5
14.5
14.5
14.5
14.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
14.5
14.5
14.5
22.5
22.5
22.5
22.5
22.5
22.5
Weight
Lbs.
240
355
320
355
320
470
470
470
190
170
190
170
265
240
265
530
530
530
800
800
800
1500
1500
1500
Data subject to change without notice.