DETECTION AREA
TOP VIEW
30
SIDE VIEW
25
20
15
10
0
5
0
DESCRIPTION:
5
10
21
30
this setting is used, the controlled lighting load will only turn on if the
ambient light present is less than the desired setting.
20
There is a daylight sensor built into the sensor to allow for ambient light
override functionality. If the ambient light level in the room is at a
9
15
Sensor designed to work with any power pack, to automatically control
lighting in standard and cold weather applications. This sensor utilizes
an industry leading 8-element Infrared Detector for superior minor
motion detection while combining with a lens that provides major
motion detection up to 2000 sq. ft. at a standard 9 ft. mounting height.
The sensor operates in climates down to -40° Fahrenheit or Celsius. Dual
Form C Relays are present on the sensor to allow for integration to
NexLight’s 2-wire system and HVAC/BMS Systems. The sensor turns the
lights on and keeps them on while occupancy is detected and will turn
14
0
14
21
(ft)
30
25
20
15
10
5
0
5
10
15
20
25
30
Field of view intersection with floor (Top view in feet 9 foot mounting height)
SETTINGS:
DETECTION AND ACTIVATION:
When a person enters a room, the sensor detects major body motion
and turns the light on. The light is kept on even as smaller body
movement is detected. This sensor’s detection sequence logic (DSL)
minimizes false triggering by continuously analyzes the motion
detection signal and adjusts internal operation to maximize the
A
B
and electrical noise.
INSTALLATION:
See the back of this installation manual for installation instructions. The
sensor is fully operational after 30 seconds of powering up the device.
OPERATION OF SENSOR
Motion detection by the HDIR sensor will turn ON the lights as well as
keep them ON. When motion is not detected, the lights will turn OFF
after the delayed-OFF time.
Delayed-OFF Time: The sensor is designed to turn the lights OFF if no
black twist knob designated for timer inside the control console. Dependent upon environmental conditions and occupancy patterns, the
adapting patterns will modify the delayed-OFF time to match the
parameters of each installation.
Walk-Through Mode: The walk-through feature is useful when a room is
momentarily occupied, such as a storage room. When a person enters
the room, the lights will turn on and stay on for 2.5 minutes. After 2.5
(Fig. Operation control console)
All aspects of sensor operation can be adjusted here
OPERATION MODE ADJUSTMENT
Switch
A1
A2
A3
A4
B1
B2
B3
B4
Function
Bank A
Not Used
Not Used
Not Used
Walk-Thru / Normal
Bank B
Daylight Sensor
LED Indicator
Test Mode
Not Used
Off
Settings
Walk-Thru Enabled
On
Normal Occupancy
Enabled
Disabled
Enabled
Disabled
Off-On-Off (Toggle Enter/Exit)
TESTING THE SENSOR
Scenario A: If motion is detected within 10 seconds of the lights shutting
Test Mode: This mode is used to set the Delayed-OFF Time to 5 seconds for
Scenario B: If no motion is detected within 10 seconds of the lights
while in test mode.
1. Ensure Power is On
2. Remove the cover from the Operation Control Console
it sees detection the lights will turn on for 2.5 minutes.
Daylight Sensor: To enable daylight sensor operation, set Dip Switch 1
in Bank B to OFF. This puts the sensor in a stand-by mode when the
natural light level exceeds the selected Foot Candles (FC) level inhibiting
the lights from turning ON.
LED Operation: The Sensor has two LED indicators that, when enabled,
has been detected by Infrared Technology.
Infrared Adjustment- For maximum range, set fully clockwise (CW). If
reduced range is required, then turn counterclockwise (CCW) and test
Delayed-OFF Time Adjustment: Each time motion is detected, the load
remains activated for a pre-set time, which is set by the Delayed-OFF
Time Adjustment, The fully CCW setting (30 seconds) can be used for
testing. The fully clockwise setting is 30 Minutes. If motion is detected
during the ON time, then the load remains activated until the full ON
time has passed since the latest motion detection.
Daylight Sensor Adjustment: This level needs to be set in a room where
natural light is at the desired level for the lighting load to not be turned
on. The sensor will still see motion (indicated by the red LEDS)
1.
Set the daylight sensor knob to fully counter clockwise (lowest level)
3.
Turn the daylight sensor knob clockwise until the light turns on.
5.
This will be the setting
defaulted to the OFF position.
4. To enter Test Mode, move the switch from OFF to ON and then back to
OFF. IF B3 is already in the ON position, test mode can be entered by just
moving it back to the OFF position.
Infra re d R a nge
Range setting
Full CCW = min.(OFF)
Full CW = max.
Notes for Test Mode:
1. The Delayed-OFF Time will remain in the 5 second test mode for 15
minutes. It will then automatically reset to the Delayed -OFF Time setting
Factory Default
Daylight Sensor
Delayed-OFF time
test mode.
2. To manually take the sensor out of the test mode, move switch B3 from
OFF to ON and back to OFF again.
Full CCW = min.(30 sec.)
Full CW = max.(30 min.)
30sec
5min
10min 20min 30min
Factory Default
Full CCW = Lights stay OFF
Full CW = Lights always turn ON (NO daylight override)
20 FC
40 FC
80 FC 160 FC 320 FC
Factory Default
Included Parts List:
Sensor (1)
Wall Anchors (3)
PIR detection Mask (1)
Slotted/Phillips Screwdriver
Pencil
Hole Saw
1
INSTALLATION INSTRUCTIONS
Base mounting ring (1)
Spring mounting clip (2)
7/8” Wall anchor screw (3)
Tools required for install:
WARNINGS AND CAUTIONS:
Wire Stripper
Wire Cutters
• To be installed and/or used in accordance with appropriate
electrical codes and regulations.
• If you are unsure about any part of these instructions,
FCC COMPLIANCE STATEMENT:
This device complies with part 15 and part 18 of the FCC rules. Operation is subject to the following two conditions: (1) This device must not
cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
2
power at
circuit breaker
3
Prepare and connect wires
Select mounting location
(For best results mount at least 6 feet away from air vents)
• Sensors must be mounted on a vibration free surface.
• All sensors must be mounted at least 6 feet away from air vents.
• Do not mount sensors closer than 10 feet from each other.
• Do not touch the surface of the PIR lens. Clean outer surface only.
4
Wiring to power pack
(typical power pack shown wire color may vary)
1/2"
(1.3 cm)
Cut
(if necessary)
WARNING:
TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER
at circuit breaker or fuse and test that power is
before wiring!
Use the included PIR Mask
when sensor location may
cause false ON’s due to
Black
Red (24V+)
Strip wire
Mask
(measure bare wire here)
Masking is not required in a corner mounting application.
Insert wires into correct terminal blocks and tighten.
Be sure to double check correct wiring connections!
Black (24V-)
Power
Pack
Hot (Black)
Blue (CTL)
Load
Blue
Blue
NORMALLY
CLOSED
5
Option A. Drop ceiling w/ mounting clips
A. remove mounting ring
B. install clips
_
Line
120/277/347VAC
60Hz
24 Vdc
5
CONTROL
NORMALLY CLOSED
COMMON
NORMALLY OPEN
By masking sections,
you can block hallway traffic
COMMON
NORMALLY OPEN
+
NORMALLY CLOSED
Black
COMMON
White
Option B. Junction box
1. Use two #8 32 screws (not supplied) to fasten the base
ring to the ceiling.
3. Press the sensor onto the base ring.
Octagon Box
4" x 1 1/2" deep
3.375 in
D. mount sensor
5
Terminal Block
Connections
1
1
Wallboard
Ceiling
NORMALLY
CLOSED
White
Option C. Base ring w/ mounting anchors
1. cut 2” hole in ceiling
2 in
2. mount sensor
Low-Voltage Wires
Wallboard
Ceiling
Low Voltage Wires
Mounting
Clips
COMMON
Neutral (White)
2. Align the sensor’s two eyelets with the base ring’s two hooks.
C. cut 3.375” hole
in ceiling
NORMALLY
OPEN
NORMALLY
OPEN
Low-Voltage
Wires
#8-32 Screws
(not supplied)
2
Mounting Anchors
Sensor
Base Ring
Mounting Screws
(2 places)
Sensor Base
Sensor Front Cover
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied