TimberBlind Metro Shade
FREE STANDING DISPLAY ASSEM BLY INSTRUCTIO NS
This display consists of:
ü 4 Upright Legs
ü 1 Top Piece
ü 1 Bottom
ü 2 Center Shelf Pieces
ü 2 Panel Brace Sections (Shelves)
ü 1 Package of Assembly Hardware:
- 44 Black Plastic Coated Set Pins
- 44 Silver Metal Cylinder Shaped Cam-locks
- 1 Sheet of Peel & Stick white Cam-lock Covers
The parts will be packaged as shown in photo #1
STEP 1
Unwrap all assembly pieces and lay out as shown in Photo #2.
Small assembly parts will be wrapped in plastic package, unwrap these and lay
out as shown in Photo #3.
Photo #4 shows a set pin and Cam-Lock next to one the large circular holes
on one of the leg pieces. All assembly of this display is done by first pushing
the set pins into the smaller holes in each section of the display parts. The
cam-locks will be inserted into the larger holes and turned with a Phillips
screwdriver to lock them in place.
*The cam-locks have a small arrow imprinted on the flat top portion. Each
should be inserted into the openings with this arrow pointed toward the
location of the set pin-hole.
Photo #5 shows the proper placement of the set pins in the smaller holes in
each assembly piece.
STEP 2
Lay out one pair of the long leg assembly pieces as shown in photo #6.
Notice the 3 holes in each piece closest to the edge of each leg. These holes
are to be used to install the 2 upright side brace sections in the center of the
display (step 3). These 3 holes should be facing towards the inside of the
display during assembly.
1
Free Standing Display Installation Instructions 4/2013
TimberBlind Metro Shade
STEP 3
Take one of the shelf piece sections and lay it flat on the floor. The 4 small set
pin holes should be facing up. Insert the 4 set pins and then set each upright
brace section in place as shown in photo #7. The large holes should be facing
outward as in photo #7. Insert set pins; Turn the cam-locks clockwise with a
Phillips screwdriver to lock the sections in place.
* This procedure will be repeated at every point where 2 sections of the
display are to be joined.
STEP 4
Place the other upright brace section on the opposite end of the assembled
section from step 3 and lock it into place with the set pins and cam-locks.
Take the 4-sided assembled section and place it over the center holes in the
pair of legs as shown in photo #8. Lock the assembly together with set pins
and cam-locks.
STEP 5
Take one of the top/bottom section pieces and set it over the holes in the pair
of assembled legs. The section that will be the bottom goes over the holes in
the legs that are about 4 inches from the end of the leg. Notice in photo #9
that the side of the bottom piece with no holes faces upward.
STEP 6 - See photo #10
The top piece of the display should be installed on the end of the pair of legs
with the holes that are only ½” from the end as shown. Be sure and turn the
cam-locks to secure this piece before moving to the next step.
STEP 7
Take the remaining pair of leg pieces and install them opposite of the pair you
have used for the assembly at this point. Line up all of the set pins you have
inserted into all open small holes facing upwards from the section of the
display you have already finished. Turn and lock all cam-locks o make sure the
completed display is stable before standing it upright.
The completed display should have a top and bottom section with 4 openings
and a center section with 2 openings and 2 braces blocking the center
opening as shown in photo #11.
2
Free Standing Display Installation Instructions 4/2013
TimberBlind Metro Shade
STEP 8
You should find 8 separate display blinds/shades/shutter that are to be
installed into the 8 openings of the display.
The top/down bottom up cordless shade and the standard honeycomb shade
are slightly larger than the other 6 products. These 2 shades will need to be
installed as outside mounts on the flat sides of the legs at the top section of
the display as shown in photo #12. All of the other display blinds will need to
be installed inside the remaining 6 openings.
The open shelf space in the display unit can be used to store your TimberBlind
Metro Shade sample books and color decks.
PHOTO KEY:
PHOTO 2
PHOTO 1
PHOTO 5
PHOTO 9
PHOTO 6
PHOTO 3
PHOTO 8
PHOTO 7
PHOTO 10
PHOTO 11
3
PHOTO 4
PHOTO 12
Free Standing Display Installation Instructions 4/2013