MP-Series
Access and Object Testing Probes
to verify the degree of protection against accidental contact in accordance with VDE resp.
DIN EN, IEC, UL and further safety standards.
Access probes to verify protection of persons from accessing dangerous parts
Object probes to verify the degree of protection of enclosures from intrusive foreign objects
Continuity signaller for contact tests
Force tester and non-positive coupling elements for test probes in tension and pressure measurements
Traceable DKD or factory calibration on request
Testing • Automation • Measurement
Joint Finger Probe
in accordance with VDE 0470 part 2 picture 2 probe B resp. IEC/EN 61032:1993
Additional standards: VDE 0470 Part 1 resp. IEC/EN 60529, IEC/EN 60950, IEC 61010, IEC/EN 60335, IEC/EN
60745-1, IEC/EN 60034-5, IEC/EN 60065, IEC/EN 60601
MP-100.04A
Access probe to assess protection of persons against access to dangerous parts and the proof of protection
against access with a finger.
The joint parts are made of high-grade steel. The handle and the stop surface consist of polyamide. In accordance
with the standards the links can be positioned at a right angle. For contact- and continuity checks a 4 mm receptacle is integrated at the handle, that is conductively connected to the finger probe.
Joint Finger Probe UL
in accordance with UL-norm UL 153, UL 197, UL 507, UL 1026, UL 1082
Access probe to assess protection of persons against access to dangerous parts in accordance with UL norm.
The joint parts and also the stop surface are made of high-grade steel. The handle consists of polyamide. The links
can be positioned at a right angle.
A 4 mm receptacle is integrated at the handle, which is conductively connected to the finger probe.
MP-100.04U
Children Joint Finger Probe
in accordance with VDE 0470 part 2 picture 12 probe 18 resp. IEC/EN 61032 with arm
extension MP-100.05B
MP-100.05A
Access probe to assess protection of children between the ages of 36 months and 14 years.
The joint parts of the finger Ø 8.6 mm are made of high-grade steel. The handle and the arm extension consist of
polyamide. The links can be positioned at a right angle.
For contact- and continuity checks a 4 mm receptacle is integrated at the handle and at the arm extension. This
is conductively connected to the finger probe. After the removal of the protection cover, the arm extension can be
screwed onto the finger probe. Note: The arm extension must be ordered separately!
Children Joint Finger Probe
in accordance with VDE 0470 part 2 picture 13 probe 19 resp. IEC/EN 61032 with arm
extension MP-100.05D
MP-100.05C
Access probe to assess protection of children 36 months of age and younger.
The joint parts Ø 5.6 mm are made of high-grade steel. The handle and the arm extension consist of polyamide.
Both links can be bend at an angle of 90 degree. For contact- and continuity checks a 4 mm receptacle is integrated at the handle and at the arm extension. This is conductively connected to the finger probe. After the removal
of the protection cover, the arm extension can be screwed onto the finger probe.
Note: The arm extension must be ordered separately!
Rigid Finger Probe with Compression Spring
in accordance with VDE 0470 part 2 picture 7 probe 11 resp. IEC/EN 61032
Additional standards: IEC/EN 60529, IEC 61010, IEC/EN 60335, IEC/EN 60065 and IEC/EN 60950-1
Access probe to assess mechanical resistance of touchable parts, with integrated compression spring in accordance with norm EN 60335-1 picture 7 and force scale from 0-50 N in 5 N-intervalls.
The probe is made of high-grade steel. In accordance with the standards the fingertip conforms to the dimensions
of the flexible finger probe MP-100.04A, picture 2, standard EN 61032.
In the handle, which is made of polyamide, is an integrated 4 mm receptacle for contact- and continuity checks.
MP-100.04B
Rigid Finger Probe with Compression Spring
in accordance with VDE 0470 part 2 picture 7 probe 11 resp. IEC/EN 61032
Additional standards: IEC/EN 60529, IEC 61010, IEC/EN 60335, IEC/EN 60065 and IEC/EN 60950-1
Access probe to the assessment of mechanical consistence of touchable parts, with integrated compression spring
in accordance with norm EN 60335-1 picture 7 and force scale from 0-100 N in 10 N-intervalls.
The probe is made of high-grade steel. In accordance with the standards the fingertip conforms to the measures
of the flexible finger probe MP-100.04A, picture 2, norm EN 61032. In the handle, which is made of polyamide,
is an integrated 4 mm receptacle for contact- and continuity checks.
MP-100.04C
Rigid Finger Probe
in accordance with VDE 0470 part 2 image 7 probe 11 resp. IEC/EN 61032
Additional standards: IEC/EN 60529, IEC 61010, IEC/EN 60335, IEC/EN 60065 and IEC/EN 60950-1
Access probe to assess protection of persons against access to dangerous parts and to assess the mechanical
resistance of openings in the enclosure or inner separations.
The finger probe is made of high-grade steel in accordance with the standards. The fingertip conforms the measures of the flexible finger probe MP-100.04A, picture 2, standard EN 61032.
The handle consists of polyamide, there is a 4 mm receptacle for contact- and continuity checks.
MP-100.04D
Rigid Finger Probe with Spherical Radius
in accordance with VDE 0805 part 1 picture 2c resp. IEC/EN 60950-1
Access probe to verify the safety of touching live parts.
The 80 mm long probe is made of high-grade steel and has a diameter of 12 mm. The result is a spherical radius
of 6 mm at the probe tip.
The handle consists of polyamide. It has a 4 mm receptacle for contact- and continuity checks.
MP-100.04Y
Fingernail Probe
in accordance with VDE 0700 part 1 picture 7 resp. IEC/EN 60335-1
Additional standards: IEC/EN 60745-1
The fingernail is made of high-grade steel. It can be attached to all inflexible finger probes and is used for the
verification of the sufficient mechanical resistance of parts which are likely to be touched.
On the finger tip, which can be bent to an angle of 90 degree, a grommet for the tensile test is attached.
MP-100.04E
Access Probe
in accordance with VDE 0470 part 2 picture 1 probe A resp. IEC/EN 61032
Additional standards: VDE 0470 part 1 resp. IEC/EN 60529
MP-100.04F
Access probe to assess protection of persons against access to dangerous parts and also against access with the
back of the hand.
The rigid test sphere Ø 50 mm is made of high-grade steel. It is chromed and hardened. The handle is made of
plastic. For contact- and continuity checks it has an integrated 4 mm receptacle which is conductively connected
to the test ball.
Access- and Object Probe
in accordance with VDE 0470 part 2 picture 3 probe C resp. IEC/EN 61032
Additional standards: VDE 0470 part 1 resp. IEC/EN 60529 and IEC/EN 60034-5
MP-100.04G
Access- and object probe for the ascertainment of protection of persons against access to dangerous parts and
also against access with a tool. Additionally the probe can be used for the assessment of the degree of protection
of enclosures against the intrusion of solid particles ≥ 2,5 mm.
The probe has a 100 mm long, sharpened metal test bar Ø 2,5 mm and a stop surface of Ø 35 mm.
The handle and the stop surface are made of plastic. For contact- and continuity checks it has an integrated 4 mm
receptacle which is conductively connected to the test bar.
Access- and Object Probe
in accordance with VDE 0470 part 2 picture 4 probe D resp. IEC/EN 61032
Additional standards: VDE 0470 part 1 resp. IEC/EN 60529 and IEC/EN 60034-5
MP-100.04J
Access- and object probe for the detection of protection of persons against access to dangerous parts and also
against access with a tool. Additionally the probe can be used for the assessment of the degree of protection of
enclosures against the intrusion of solid particles ≥ 1,0 mm. The probe has a 100 mm long, sharpened metal test
bar Ø 1 mm and a stop surface with Ø 35 mm.
The handle and the stop surface are made of plastic. For contact- and continuity checks it has an integrated 4 mm
receptacle which is conductively connected to the test bar.
Cylinder Test Pin
in accordance with VDE 0470 part 2 picture 8 probe 12 resp. IEC/EN 61032
Additional standards: IEC/EN 60950 and IEC 60035
MP-100.14M
Access- and object probe for the detection of protection of persons against access to dangerous, active parts and
also against the accidental access with a tool e.g. screwdriver or with a similarly sharp object.
The cylinder test pin Ø 4 mm is 50 mm long. It is made of high-grade steel and enclosed in a plastic holder.
There is a 4 mm receptacle conductively connected to the probe for contact- and continuity checks.
Cone Test Pin
in accordance with VDE 0470 part 2 picture 9 probe 13 resp. IEC/EN 61032
Additional standards: IEC/EN 60950 and IEC 60035
Access probe for the ascertainment of protection of persons against access to dangerous, active parts in the
equipment of protection classes 0 and II.
The cylinder test pin is 15 mm long and passes conical from Ø 4 mm to Ø 3 mm. The probe part is made of highgrade steel and enclosed in a plastic holder.
There is a 4 mm receptacle conductively connected to the probe for contact- and continuity checks.
MP-100.04N
Cone Test Pin
in accordance with VDE 0470-2:1993-04 resp. EN 61032:1993-04 and IEC 61032
Access- and object probe for the detection of protection of persons against access to dangerous, active parts.
The cylinder test pin is 50 mm long and passes conical from Ø 4 mm to Ø 3 mm. The probe part is made of highgrade steel and enclosed in a plastic holder.
There is a 4 mm receptacle conductively connected to the probe for contact- and continuity checks.
MP-100.04M
Continuity Signaler
in accordance with VDE0700 part 1 resp. IEC/EN 60335-1
Additional standards: VDE 0470 Part 2
In accordance with the standards for contact tests the electrical continuity can be tested with access probes in
accordance with VDE 0470 part 2. A visible and audible signal is output at a resistance of ≤ 15 Ω.
The required potential-free test voltage of 48 V is be created with a safety transformer. The power supply is provided via a 230 V network connection. Two 4 mm safety connection cables are included in the delivery.
MP-100.09B
Tension- and Compression Force Meter
determination of the tension- and compression force in association with access probes
Microprocessor-controlled force measuring device for tension- and compression measurements up to 20 kg resp.
196 N.
The measurement has the following characteristics: memory for maximum values, zeroing by means of keystroke,
automatic shutdown, battery power level indicator and overload protection. Over the integrated RS232 interface
measured values can be transmitted.
The force measurement is powered by 6 x 1,5 V AA mignon batteries or a 9 V adapter.
Batteries, different adapters, 120 mm long extension rod, standards manual and equipment case are included in
the delivery.
MP-100.15A
Connecting Set
connection adapter for tension- and compression force measuring device MP-100.15A
Used for the force fitted coupling with the M4 metric thread of finger probes to the tension- and compression
force measuring device MP-100.15A.
MP-100.15B
Test Sphere
in accordance with VDE 0470 part 2 picture 6 Probe 2 resp. IEC/EN 61032
Additional standards: VDE 0470 Part 1 resp. IEC/EN 60529
Object probe for the ascertainment of the degree of protection of enclosures against the intrusion of solid particles
≥ 12.5 mm in the equipment. In accordance with the standards it is possible to check the mechanical resistance
with the help of a shock test. Chromed and hardened test sphere with a diameter of 12,5 mm.
MP-100.04K
Test Sphere
in accordance with VDE 0470 part 2 picture 5 Probe1 resp. IEC/EN 61032
Additional Standard: VDE 0470 part 1 resp. IEC/EN 60529 and IEC/EN 60034-5
MP-100.04H
Object probe for the ascertainment of the degree of protection of enclosures against the intrusion of solid particles
≥ 50 mm in the equipment.
In accordance with the standards it is possible to check the mechanical resistance with the help of a shock test.
Chromed and hardened test sphere with a diameter of 50 mm and a weight of 0,510 kg.
Test Sphere
in accordance with VDE 0470 part 2 picture 5 Probe 1 resp. IEC/EN 61032
Additional standards: VDE 0470 part 1 resp. IEC/EN 60529, IEC/EC 60950-1 and IEC/EN 60065
MP-100.04L
Object probe for the ascertainment of protection of enclosures against the intrusion of solid particles ≥ 50 mm
in the equipment.
In accordance with the standards it is possible to check the mechanical resistance with the help of a shock test.
Chromed and hardened test sphere with a diameter ≥ 50 mm and a weight of 0.510 kg.
There is a grommet for horizontal testing.
Test Sphere
in accordance with VDE 0700-69 resp. EN 60335-2-69
Object probe for the ascertainment of protection of persons and for checking the mechanical resistance of the
material. With the help of the test sphere the protection of the equipment against intrusive solid particles can be
tested. Furthermore the protection of the back of the hand can be rated.
Chromed and hardened test sphere with a diameter ≥ 50,8 mm and a weight of 0,535 kg.
MP-100.04Q
Test Mandrel
in accordance with VDE 0470 part 2 picture 16 Probe 41 resp. IEC/EN 61032
Additional standards: IEC/EN 60529
Access probe for the ascertainment of protection of persons against access to dangerous, hot or glowing parts.
The test mandrel is 80 mm long, Ø 30 mm and made of high-grade steel. It has a 21.5 mm long and sharpened
tip. The holder is made of polyamide. It is 80 mm long, Ø 50 mm and has a 4 mm receptacle for contact- and
continuity checks. The receptacle is conductively connected to the probe part.
MP-100.04P
Test Plug
in accordance with VDE 0860 picture 9 resp. IEC/EN 60065
Additional standards: IEC 60169-2 picture 7
Probe for the mechanical testing of coaxial antenna connections.
The test plug is made of high-grade steel and is hardened.
MP-700.20A
Test Hook
in accordance with VDE 0860 picture 4 resp. IEC/EN 60065
Probe for the ascertainment of the resistance of enclosures against the impact of external forces up to 20 N. The
test hook is made of high-grade steel and is bent at an angle of 90 degree. It has the following dimensions: 180
mm x 8 mm x 5 mm.
MP-700.30A
Impact Hammer
in accordance with IEC, CEE, EN, UL, DIN, VDE and other national standards, full description look IEC 60068-2-63 /1991, IEC 60068-2-75
Used for impact testing to determine mechanical resistance.
The impact hammer allows testing with the following impact energies: 0.20 J / 0.35 J / 0.50 J / 0.70 J / 1.00 J
MP-100.01A
Ball Pressure Apparature
in accordance with VDE 0700-1:2001-01 picture 12 resp. IEC/EN60335-1:2001-01
Apparature for the determination of the mechanical resistance of insulators.
The ball pressure probe is completely made of high-grade steel, has a total weight of
2040 g and places a force of 20 N on the surface of the object being tested.
The spherical pressure probe, with a spherical radius of 2.5 mm, is changeable.
MP-100.01F
ACCESSORY
Small Safekeeping Case
The small safekeeping case is suitable for safe transport and also for the storage of the
following Probes:
1 Fingernail Probe MP-100.04E
1 Test Sphere MP-100.04K
1 Cone Test Pin MP-100.04N
1 Test Pin MP-100.14M or MP-100.04M
MP-100.10Z
Size: 120 x 120 x 30 mm
Big Safekeeping Case
The safekeeping case is suitable for the safe transport and also for the storage of the
following rigid probes:
MP-100.13Z
1 Fingernail Probe MP-100.04E
1 Test Sphere MP-100.04K
1 Cone Test Pin MP-100.04N
1 Test Pin MP-100.14M or MP-100.04M
1 Joint Finger Probe MP-100.04A or MP-100.04U
2 Finger Probes MP-100.04B, C, D or Y
2 Access Probes MP-100.04G and MP-100.04J
1 Access Probe MP-100.04F
1 Test Sphere MP-100.04H, L or Q
Size: 450 x 360 x 106 mm
Wooden Case with Foam Padding
Several variants of the stable wooden case are available. Through the foam insert,
which fits exactly, MP series probes can be stored safely.
Size: 350 x 110 x 100 mm resp. 500 x 140 x 100 mm
MP-100.15Z
Wilhelm-Maybach-Str. 3 • 74564 Crailsheim
Phone +49 (0) 7951 9150-0 • Fax +49 (0) 7951 9150-27
e-mail: info@stahl-prueftechnik.de
http://www.stahl-prueftechnik.de