HIGH NOISE REDUCTION/
HIGH SPEED 10 Mbps,
TOTEM-POLE OUTPUT TYPE PS9711
5 PIN SOP TOM OPTOCOUPLER
FEATURES
DESCRIPTION
• HIGH COMMON MODE TRANSIENT IMMUNITY
CMH, CML: ±10 kV/µs TYP
The PS9711 is an optically coupled high speed totem pole
isolator containing a GaAIAs LED on the light emitting diode
side (input side) and a photodiode and a signal processing
circuit on the light receiving side (output side) on one chip. It
is housed in a plastic SOP (Small Out-Line Package) for high
density applications.
• SMALL PACKAGE
5 pin SOP
• HIGH SPEED RESPONSE
tPHL = 30 ns, tPLH = 35 ns TYP
• PULSE WIDTH DISTORTION
|tPHL-tPLH| = 7 ns TYP
• TOTEM-POLE OUTPUT
No Pull-up resistor required
APPLICATIONS
• TAPE AND REEL AVAILABLE
• COMPUTER AND PERIPHERAL DEVICES
• MEASUREMENT EQUIPMENT
• POWER SUPPLY
ELECTRICAL CHARACTERISTICS (TA = -40 to +85 °C, unless otherwise specified)
PART NUMBER
Coupled
Detector
Diode
SYMBOLS
PS9711
PARAMETERS
UNITS
MIN
TYP
MAX
1.4
1.65
1.9
VF
Forward Voltage, IF = 10 mA, TA = 25°C
V
IR
Reverse Current, VR = 3 V, TA = 25°C
µA
Ct
Capacitance, V = 0, f = 1.0 MHz, TA = 25°C
pF
10
30
IOH
High Level Output Current, VCC = VO = 5.5 V, IF = 250 µA
µA
VOH
High Level Output Voltage, VCC = 4.5 V, IF = 250 µA, IOH = -2 mA
V
VOL
Low Level Output Voltage, VCC = 4.5 V, IF = 7 mA, IO = 8 mA
V
ICCH
High Level Supply Current, VCC = 5.5 V, IF = 0 mA
ICCL
Low Level Supply Current, VCC = 5.5 V, IF = 10 mA
IOSH
High Level Output Short Circuit Current,
VCC = 5.5 V, VO =GND, IF = 0 mA, 10 ms or less
mA
-26
IOSL
Low Level Output Short Circuit Current,
VCC = 5.5 V, VO =GND, IF = 8 mA, 10 ms or less
mA
34
2.0
1
2.4
200
3.0
0.38
0.6
mA
11
17
mA
12
18
IFHL
Threshold Input Current, High → Low, VCC = 5 V
TA = 25°C
mA
IFLH
Threshold Input Current, Low → High, VCC = 5 V
TA = 25°C
mA
0.5
0.35
RI-O
Isolation Resistance, Vin-out = 1 kVDC, RH = 40 to 60%, TA = 25°C
Ω
1011
CI-O
Isolation Capacitance, V = 0, f = 1.0 MHz, TA = 25°C
pF
tPHL
Propagation Delay Time, High →
ns
15
10
30
65
85
tPLH
Propagation Delay Time, Low → High2 ,VCC = 5 V, IF = 7.5 mA
ns
15
35
65
7
35
Low2
, VCC = 5 V, IF = 7.5 mA
TA = 25°C
TA = 25°C
|tPHL-tPLH|
Pulse Width Distortion, (PWD)2,VCC = 5 V, IF = 7.5 mA
5
6
0.6
10
ns
85
CMH
Common Mode Transient Immunity at High Level Output3
VCC = 5 V, TA = 25°C, IF = 0 mA, VO(min) = 2 V , VCM = 100 V
kV/µs
1
10
CML
Common Mode Transient Immunity at Low Level Output3
VCC = 5 V, TA = 25°C, IF = 7.5 mA, VO = 0.8 V (max) RL = 350 Ω
VCM = 1 kV
kV/µs
1
10
SEE NOTES ON NEXT PAGE
California Eastern Laboratories
PS9711
ELECTRICAL CHARACTERISTICS NOTES:
1. Typical Values at TA = 25°C.
2. Test Circuit for Propagation Delay Time:
VCC = 5 V
Pulse Input (IF)
(
VO (Monitor)
PW = 500 ns
Duty Cycle = 1/2
)
VCC
Input
Monitor
CL = 15 pF
VCC = 5 V
IF (ON)
50% IF (ON)
Input
0.1 µF
0.1
µF
VON
Output
*CL =
30pF
GND
1.5 V
VOL
2.5 kΩ
tPHL
47 Ω
tPLH
CL is approximately 15 pF, which includes probe and stray wiring capacitance.
3. Test Circuit for Common Mode Transient Immunity
VCC = 5 V
100 V
VCM 90%
GL SW IF
VCC
0.1
µF
10%
0V
VO (Monitor)
tr
CL = 15pF
tf
GND
VOH
2V
0.8 V
VOL
VO
IF = 0 mA
VO
IF = 7.5 mA
CL is approximately 15 pF, which includes probe and stray wiring capacitance.
USAGE CAUTIONS
1. Protect against static electricity when handling.
2. By-pass capacitor of more than 0.1 µF is used between VCC and
GND near device.
RECOMMENDED
OPERATING CONDITIONS
PART NUMBER
ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C)
SYMBOLS
Diode
VR
IF
Detector
VCC
VO
IOH
IOL
PD
Coupled
BV
TSTG
TA
PARAMETERS
UNITS
RATINGS
Reverse Voltage
Forward Current (DC)
V
mA
3.0
30
Supply Voltage
Output Voltage
High Level Output Current2
Low Level Output Current2
Power Dissipation
V
V
mA
mA
mW
7
7
-5
13
130
SYMBOLS
Vr.m.s.
°C
°C
2500
-55 to +125
-40 to +85
Notes:
1. Operaion in excess of any one of these parameters may result
in permanent damage.
2. TA = -40 to +85°C.
3. AC voltage for 1 minute at TA = 25 °C, RH = 60 % between input
and output.
UNITS MIN TYP MAX
IFH
High Level Input Current
mA
7.5
IFL
Low Level Input Current
µA
0
VCC
Supply Voltage
V
4.5
N
TTL → RL = 1 kΩ
12.5
250
5.0
TTL
5.5
3
ORDERING INFORMATION
PART NUMBER
PS9711
Isolation Voltage3
Storage Temperature
Operating Temperature
PS9711
PARAMETERS
PS9711-E3
PACKAGE
PACKING STYLE
5 Pin SOP
Magazine case 100 pcs
Embossed Tape 900 pcs/reel
PS9711-E4
PS9711-F3
PS9711-F4
Embossed Tape 3500 pcs/reel
PS9711
OUTLINE DIMENSIONS (Units in mm)
PIN CONNECTION (Top View)
PS9711
5
4
3
1.
2.
3.
4.
5.
4.0±0.5
1
+0.10
0.4 -0.05
Anode
Cathode
GND
VO
VCC
2
0.25 M
INTERNAL OUTPUT CIRCUIT
7.0 ± 0.3
4.4
1.3
VCC (5)
2.1±0.2
+0.10
0.15 -0.05
0.1 ± 0.1
1.27
0.5 ± 0.3
1.2
MAX
VO (4)
LED
OUTPUT
ON
L
OFF
H
GND (3)
TYPICAL PERFORMANCE CURVES (TA = 25°C unless otherwise specified)
DETECTOR POWER DISSIPATION
vs. AMBIENT TEMPERATURE
MAXIMUM FORWARD CURRENT
vs. AMBIENT TEMPERATURE
200
Detector Power Dissipation, Pc (mW)
Maximum Forward Current, IF (mA)
40
30
20
10
0
20
40
80 85
60
150
100
50
0
100
20
Ambient Temperature, TA (°C)
100
SUPPLY CURRENT
vs. AMBIENT TEMPERATURE
100
20
High Level Supply Current, ICCH (mA)
Low Level Supply Current, ICCL (mA)
Forward Current IF (mA)
80 85
60
Ambient Temperature, TA (°C)
FORWARD CURRENT
vs. FORWARD VOLTAGE
10
TA = 100 ˚C
50 ˚C
25 ˚C
0 ˚C
-25 ˚C
1.0
0.1
0.01
1.0
40
1.2
1.4
1.6
1.8
2.0
Forward Voltage, VF (V)
2.2
2.4
VCC = 5.5 V,
ICCH: IF = 0 mA
ICCL: IF = 10 mA
18
16
14
ICCL
12
ICCH
10
8
6
4
2
0
-50
-25
0
25
50
75
Ambient Temperature, TA (°C)
100
PS9711
TYPICAL PERFORMANCE CURVES (TA = 25°C unless otherwise specified)
HIGH LEVEL OUTPUT VOLTAGE
vs. AMBIENT TEMPERATURE
HIGH LEVEL OUTPUT VOLTAGE
vs. HIGH LEVEL OUTPUT CURRENT
5
VCC = 4.5 V,
IF = 250 µA
4
VCC = 4.5 V, IF = 250 µA,
IOH = -2 mA
High Level Output Voltage, VOH (V)
High Level Output Voltage, VOH (V)
5
TA = +85°C
+25°C
-40°C
3
2
1
0
0
-1
-2
-3
-4
-5
-6
4
3
2
1
0
-50
High Level Output Current IOH (mA)
2
TA = +85°C
+25°C
1
-40°C
5
15
10
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
-50
-25
0
25
50
70
Propagation Delay Time, tPHL, tPLH (ns)
Pulse Width Distortion, |tPHL - tPLH| (ns)
60
tPLH
40
30
tPHL
20
10
0
-10
PWD
-20
-30
10
15
20
Forward Current, IF (mA)
100
PROPAGATION DELAY TIME,
PULSE WIDTH DISTORTION
vs. AMBIENT TEMPERATURE
VCC = 5 V
50
75
Ambient Temperature, TA (°C)
70
5
100
0.8
PROPAGATION DELAY TIME,
PULSE WIDTH DISTORTION
vs. FORWARD CURRENT
0
75
VCC = 4.5 V, IF = 7 mA,
IO = 8 mA
0.9
Low Level Output Voltage, VOH (V)
Low Level Output Voltage, VOH (V)
50
1.0
Low Level Output Current IOH (mA)
Propagation Delay Time, tPHL, tPLH (ns)
Pulse Width Distortion, |tPHL - tPLH| (ns)
25
LOW LEVEL OUTPUT VOLTAGE
vs. AMBIENT TEMPERATURE
VCC = 4.5
IF = 7 mA
0
0
Ambient Temperature, TA (°C)
LOW LEVEL OUTPUT VOLTAGE
vs. LOW LEVEL OUTPUT CURRENT
3
-25
25
VCC = 5 V,
IF = 7.5 mA
60
50
tPLH
40
tPHL
30
20
10
PWD
0
-50
-25
0
25
50
75
Ambient Temperature, TA (°C)
100
PS9711
TYPICAL PERFORMANCE CURVES (TA = 25°C unless otherwise specified)
Threshold Input Current, IFHL, IFLH (mA)
THRESHOLD INPUT CURRENT
vs. AMBIENT TEMPERATURE
8
VCC = 5 V
7
6
5
4
3
IFHL
2
IFLH
1
0
-50
-25
0
25
50
75
100
Ambient Temperature, TA (°C)
TAPING SPECIFICATIONS (Units in mm)
TAPE OUTLINE AND DIMENSIONS
TAPE DIRECTION
4±0.1
2±0.1
1.55±0.1
PS9711-E3
1.75±0.1
PS9711-E4
2.4±0.1
5.5±0.1
12±0.2
1.55±0.1
8±0.1
7.4±0.1
4.6±0.1
0.3
REEL OUTLINE AND DIMENSIONS
2.0
15°
φ60
φ180
15°
φ13.0±0.5
2.0±0.5
φ13.0±0.5
φ21.0±0.8
Packing: 900 pcs/reel
13.0±1.0
PS9711
TAPING SPECIFICATIONS (Units in mm)
TAPE DIRECTION
TAPE OUTLINE AND DIMENSIONS
4±0.1
2±0.1
1.55±0.1
1.75±0.1
PS9711-F3
PS9711-F4
2.4±0.1
5.5±0.1
12±0.2
1.55±0.1
8±0.1
7.4±0.1
4.6±0.1
0.3
REEL OUTLINE AND DIMENSIONS
1.5 ± 0.1
1.5 ± 0.1
12
0°
1.5 ± 0.5
60
°
Packing: 3500 pcs/reel
φ66
2.0 ± 0.5
φ13.0±0.5
PS89701-E3, E4: φ178
PS9701-F3, F4: φ 330
φ21.0 ± 0.8
6.0 ± 1
+2.0
12.4 -0.0
18.4 MAX
PS9711
RECOMMENDED SOLDERING CONDITIONS
(1) Infrared reflow soldering
235 ˚C or below (package surface temperature)
30 seconds or less
• Number of reflows
Three
• Flux
Rosin flux containing small amount of chlorine (The flux
with a maximum chlorine content of 0.2 Wt % is
recommended).
Package Surface Temperature T (˚C)
• Peak reflow temperature
• Time of temperature higher than 210 ˚C
(heating)
to 10 s
235 ˚C (peak temperature)
210 ˚C
to 30 s
100 to 160 ˚C
60 to 120 s
(preheating)
Time (s)
(2) Dip soldering
• Temperature
260 ˚C or below (molten solder temperature)
• Time
10 seconds or less
• Number of times
One (Allowed to be dipped in solder including plastic mold portion.)
• Flux
Rosin flux containing small amount of chlorine (The flux
with a maximum chlorine content of 0.2 Wt % is recommended).
(3) Cautions
• Fluxes
Avoid removing the residual flux with chlorine-based cleaning solvent after a reflow process.
Life Support Applications
These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected
to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify
CEL for all damages resulting from such improper use or sale.
EXCLUSIVE NORTH AMERICAN AGENT FOR
RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS
CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279
24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) • Internet: http://WWW.CEL.COM
12/04/2001
DATA SUBJECT TO CHANGE WITHOUT NOTICE