“S
cout
”
where Ideas become Solutions
End Sub
Stabilizer
S C O U T S y st e m C o m p o n e n ts
Pulser
Generator
Directional
Rotary Steerable System
Stabilizer
RSS
“Scout”
The 3D Rotary Steerable System “Scout” is an automatic steering tool for three dimensional drilling. The use of the “Scout” systems offers many advantages, namely
higher rate of penetration drilling, improved cuttings removal, optimum drilling
course and higher borehole stability. These advantages result in overall cost reduction and a higher borehole quality.
Operational
Specifications
Hole Size
Build up Rate
Max. Operating Torque
Max. WOB
Max. RPM
Max. Flow Rate
Max. Temperature
Max. Hydrostatic
Pressure
Mud Compatibility
Max. Mud Sand
Content (by volume)
Bit
Rotary Connections
Top Connection
(End Sub)
Bit Box
SCOUT 2000
SCOUT 3000
SCOUT 4000
6“ to 6 ¾“
0 to 6.5°/100 ft
8,115 ft-lbf (11 kNm)
15,750 lbf (70 kN)
250 min–1
291 GPM (1,100 l/min)
257/302 ° F (125/150 ° C)
8,700 psi
(600 bar)
Oil based Mud /
Water based Mud
1 %
8 ½“ to 9 7/8“
0 to 6.5°/100 ft
11,070 ft-lbf (15 kNm)
44,962 lbf (200 kN)
250 min–1
529 GPM (2,000 l/min)
257/302 ° F (125/150 ° C)
8,700/20,000 psi
(600/1,400 bar)
Oil based Mud /
Water based Mud
1 %
12 ¼“ to 13 7/8“
0 to 6.0°/100 ft
22,140 ft-lbf (30 KNm)
56,250 lbf (250 kN)
250 min–1
1,058 GPM (4,000 l/min)
257/302 ° F (125/150 ° C)
8,700/20,000 psi
(600/1,400 bar)
Oil based Mud /
Water based Mud
1 %
NC 38 Box
NC 46 Box
NC 56 Box
3 ½ Reg.
4 ½ Reg.
6 5/8 Reg.
where Ideas become Solutions
SCOUT 2000 / SCOUT 3000 / SCOUT 4000
Rotary Steerable System · Tool Specifications
Components of Bottom Hole Assembly
Data Receiving Unit
Electro-hydraulic Choke Mechanism for Downlink
E n v iro n m en tal Specificatio n s
Vibration Test of PCB
Axes
Duration
Scout Tool
Available in
three sizes:
Scout 2000
Hole Size
6“ to 6 ¾“
Scout 3000
Hole Size
8 ½“ to 9 7/8“
Scout 4000 Hole Size
12 ¼“ to 13 7/8“
Contact Details
Address
Middelicher Str. 305
45892 Gelsenkirchen
Germany
Phone
+49 209 386342-0
Fax
+49 209 386342-99
Email
info@smartdrilling.de
Internet
www.smartdrilling.com
www.smart-drilling.de
High Frequency Test
Level
Frequency
Low Frequency Test
Level
Frequency
Temperature Test of PCB
Thermal Soak
Temperature
Duration
Thermal Cycling
Temperature Profile
Temperature Ramp
No. of Cycles
Shock Test of RSS-Tool
Drop Test
Axes
Height of Drop
Number
Air Hammer Test
Axes
Frequency
Duration
Pressure Test of RSS-Tool
Pressure Soak
Temperature of Water
Pressure
Duration
Pressure Cycling
Temperature of Water
Pressure Profile
No. of Cycles
X, Y, & Z (orthogonal)
4 hours per axis (continuous)
4.0–6.0 g
15 dB (1,000–10,000 Hz),
30 dB (10,000–100,000 Hz)
20 g RMS (random)
10–500 Hz
125 °C / 150 °C
120 hours (continuous)
120 minutes @ –20 °C
120 minutes @ 125 °C
60 minutes (minimum)
25
X, Y, & Z (orthogonal)
18“ (0.4572 m)
10 drops per axis
X, Y, & Z (simultaneous)
50–100 Hz
12 hours (continuous)
99 °C (not boiling)
600 bar / 1,400 bar
72 hours (continuous)
70 °C
1 bar for 5 minutes
14 bar for 30 minutes
600 bar for 30 minutes
10
S pecificatio n s of MW D - Sy stem
Inclination
Sensor
Accuracy
Raw Data to Surface
Gtot Quality Check Tolerance
Direction
Sensor
Accuracy
Raw Data to Surface Btot Quality Check Tolerance
Dip Angle Quality Check Tolerance
Logging
Logging Capability
X-, Y-, & Z-Axis Accelerometers
± 0.1°
Gx, Gy , Gz
± 0.005 g
X-, Y-, & Z-Axis Magnetometers
± 1.0°
Bx, By , Bz
± 0.3 µ T
± 0.5°
Gamma Sensor