TPD4E002 www.ti.com SLVS615D – JULY 2006 – REVISED JUNE 2010 QUAD LOW-CAPACITANCE ARRAY WITH ±15-kV ESD PROTECTION Check for Samples: TPD4E002 FEATURES APPLICATIONS • • 1 • • • • • • • Four Unidirectional Voltage Suppression Diodes for use in ESD Protection I/O Breakdown Voltage, VBR = 6.1 V Min Low I/O Capacitance (11 pF at 0 V) Low I/O Leakage Current <100 nA 2.5-A Peak Pulse Current (8/20-ms Pulse) No Power Supply Routing is Required since there is no VDD Pin Very Small Printed Circuit Board (PCB) Area <2.6 mm2 ESD Protection Exceeds – ±15-kV Human Body Model (HBM) – ±15-kV IEC 61000-4-2 Contact Discharge Where Transient Overvoltage Protection in ESD-Sensitive Equipment is Required, Such as: – Computers – Printers – Communication Systems and Cellular Phones – Video Equipment BENEFITS • • • High ESD Protection Level High Integration Suitable for High-Density Boards DRL PACKAGE (TOP VIEW) IO1 1 5 IO4 GND 2 IO2 3 4 IO3 DESCRIPTION/ORDERING INFORMATION The TPD4E002 is a monolithic array designed to protect up to four lines against ESD transients. Monolithic circuit design allows superior matching between the channels and reduced crosstalk. This device is ideal for applications where both reduced line capacitance and board space-saving are required. ORDERING INFORMATION PACKAGE (1) TA –40°C to 125°C (1) (2) 1.6 × 1.6 DRL Reel of 4000 ORDERABLE PART NUMBER TPD4E002DRLR TPD4E002DRL2 (2) TOP-SIDE MARKING 28S For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. The TPD4E002DRL2 is the same exact device as the TPD4E002DRL. This special orderable offers 180 degree shift in device orientation in the reel compared to TI standard DRL package orientation in the reel. Refer to the tape and reel information section at the end of this datasheet for the details on orientation information. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2006–2010, Texas Instruments Incorporated TPD4E002 SLVS615D – JULY 2006 – REVISED JUNE 2010 www.ti.com Absolute Maximum Ratings MIN VPP ESD discharge TJ Junction temperature Tstg Storage temperature range Top Operating temperature range MAX Human Body Model (HBM) ±15 IEC 61000-4-2 Contact Discharge ±15 UNIT kV 125 °C –55 150 °C –40 125 °C Peak pulse power tp = 8/20 µs 35 W Peak pulse current tp = 8/20 µs 2.5 A Thermal Resistance PARAMETER RqJA 2 Junction to ambient on printed circuit on recommended pad layout Submit Documentation Feedback VALUE UNIT 220 °C/W Copyright © 2006–2010, Texas Instruments Incorporated Product Folder Link(s): TPD4E002 TPD4E002 www.ti.com SLVS615D – JULY 2006 – REVISED JUNE 2010 Electrical Characteristics Tamb = 25°C PARAMETER TEST CONDITIONS MIN TYP UNIT VBR I/O Breakdown voltage IR = 1 mA IRM I/O Leakage current VRM = 3 V aT Voltage temperature coefficient 45 10–4/°C C I/O Capacitance per line 11 pF 2 Ω Rd (1) Dynamic resistance 6.1 MAX (1) 7.2 V 0.1 mA Rd is measured under reverse breakdown condition with inrush current in the range 1Amps using pulse technique TYPICAL CHARACTERISTICS 12.0 Capacitance (pF) 11.5 11.0 10.5 10.0 9.5 9.0 8.5 8.0 –40 0 25 70 85 125 Temperature (ºC) Figure 1. I/O Capacitance vs Temperature 12.0 Capacitance (pF) 11.5 11.0 10.5 10.0 9.5 9.0 1 2 3 4 5 6 7 8 9 10 Frequency (Mhz) Figure 2. I/O Capacitance vs Frequency (Typical Values) Submit Documentation Feedback Copyright © 2006–2010, Texas Instruments Incorporated Product Folder Link(s): TPD4E002 3 TPD4E002 SLVS615D – JULY 2006 – REVISED JUNE 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) –110.0 –100.0 –90.0 –80.0 –70.0 –60.0 –50.0 –40.0 –30.0 IIN (mA) –20.0 –10.0 0.00 10.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0 90.0 100.0 110.0 8.0 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 500m 0 –500m –1.0 –1.5 VIN (V) Voltage (20 V/div) Figure 3. Diode Current Across I/O Voltage (Typical Values) Time (50 ns/div) Figure 4. ESD Clamp Voltage At I/O Pins: IEC6100-4-2 15 kV Contact Discharge 4 Submit Documentation Feedback Copyright © 2006–2010, Texas Instruments Incorporated Product Folder Link(s): TPD4E002 TPD4E002 www.ti.com SLVS615D – JULY 2006 – REVISED JUNE 2010 3.0 30 2.5 25 2.0 20 Current (A) 1.5 15 1.0 10 PPP (W) IPP (A) TYPICAL CHARACTERISTICS (continued) Power (W) 5 0.5 0.0 0 0 5 10 15 20 25 30 35 Time (µs) 40 45 50 Figure 5. Pulse Waveform (8/20 µs Pulse) Submit Documentation Feedback Copyright © 2006–2010, Texas Instruments Incorporated Product Folder Link(s): TPD4E002 5 PACKAGE OPTION ADDENDUM www.ti.com 27-Jul-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) TPD4E002DRL2 ACTIVE SOT DRL 5 4000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Request Free Samples TPD4E002DRLR ACTIVE SOT DRL 5 4000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Request Free Samples TPD4E002DRLRG4 ACTIVE SOT DRL 5 4000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Request Free Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 18-Feb-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPD4E002DRL2 SOT DRL 5 4000 180.0 8.4 1.98 1.78 0.69 4.0 8.0 Q2 TPD4E002DRLR SOT DRL 5 4000 180.0 8.4 1.98 1.78 0.69 4.0 8.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 18-Feb-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPD4E002DRL2 SOT DRL 5 4000 202.0 201.0 28.0 TPD4E002DRLR SOT DRL 5 4000 202.0 201.0 28.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated