WARNING
To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts and other hazards:
• Service of the equipment must be performed by qualified service personnel.
• Installation and maintenance must be performed by a person familiar with the construction and operation of this product and any hazards involved. All applicable codes and ordinances must be followed.
• Read this document before installing, servicing or maintaining this equipment or installing a lamp. These instructions do not cover all installation, service and maintenance situations. If your situation is not covered, or, if you do not understand these instructions or additional information is required, contact Peerless Lighting or your local Peerless
Lighting distributor.
• Read and follow all warnings and instructions provided by the lamp manufacturer.
WARNING
Before installing, servicing or maintaining this equipment, follow these general precautions. To reduce the risk of electrocution:
• Make sure the equipment is properly grounded.
• Always de-energize the circuit and/or equipment before connecting to, disconnecting from or servicing the equipment.
To prevent luminaire row from over-current:
• By adding the input current of each luminaire section marked on the luminaire, the total current per power feed must not exceed the maximum line wire amperage marked on the luminaire and the power feed cord/wire amperage rating whichever is the least.
To reduce the risk of fire:
• Keep material away that can burn from hot lamp.
• Make sure lamps are correctly installed.
• Use supply conductors with a minimum installation temperature rating as specified on equipment.
To reduce the risk of personal injury from cuts, abrasions or falling parts:
• Wear gloves to prevent cuts or abrasions from sharp edges when removing from carton, handling and maintaining this equipment.
• Do not use abrasive materials, glass cleaners or other solvents on reflector or lens. These substances may damage equipment and cause parts to eventually break and fall.
• Do not install a damaged fixture.
CAUTION
Observe lamp manufacturer’s recommendations and restrictions on lamp operation including but not limited to ballast type, burning position, replacement and cycling. Use only lamps that comply with applicable ANSI standards.
NOTICE: If lamp is marked it contains mercury. Follow disposal laws. See www.lamprecycle.org
Peerless Lighting, a division of Acuity Brands Lighting, Inc., assumes no responsibility for claims arising out of improper or careless installation or handling of this product.
SAVE THESE INSTALLATION INSTRUCTIONS
Part Number: PIN004100 Revision: E Effective Date: 07/2012 ECO3665
• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings and instructions included with and on the luminaire box and all luminaire labels.
•
Before installing, servicing or performing routine maintenance upon this equipment, follow these general precautions.
•
Installation and service of luminaires should be performed by a qualified licensed electrician .
•
Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved.
Regular luminaire maintenance programs are recommended.
•
It will occasionally be necessary to clean the outside of the refractor/lens.
Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user.
Refractor/lens should be washed in a solution of warm water and any mild, non ‐ abrasive household detergent, rinsed with clean water and wiped dry.
Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.
• DO NOT INSTALL DAMAGED PRODUCT!
This luminaire has been properly packed so that no parts should have been damaged during transit.
Inspect to confirm.
Any part damaged or broken during or after assembly should be replaced.
•
Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
•
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation or maintenance.
Should further information be desired or
should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.
a parent company of Peerless Lighting.
9
WARNING installation or servicing.
comparing it with the
RISK OF ELECTRIC SHOCK
9 Disconnect or turn off power before
9 Verify that supply voltage is correct by luminaire label information.
9 Make all electrical and grounded connections in accordance with the National Electrical Code
(NEC) and any applicable local code requirements.
All wiring connections should be capped with
UL approved recognized wire connectors.
9 To prevent luminaire row from over ‐ current:
By adding the input current of each luminaire section marked on the luminaire, the total current per power feed must not exceed the maximum line wire amperage marked on the luminaire and the power feed cord/wire amperage rating whichever the least.
WARNING
RISK OF BURN
9 Allow lamp/luminaire to cool before handling.
Do not touch enclosure or light source.
9 Do not exceed maximum wattage marked on luminaire label.
9 Follow all manufacturer’s warnings, recommendations and restrictions for: driver type, burning position, mounting locations/methods, replacement and recycling.
Part Number: PIN004102 Description: “INSTR, IMPORTANT SAFETY LED” Revision: C Effective Date: 07/2012 ECO3665 page 1 of 2
9 Wear gloves and safety glasses at all times
9 when removing installing,
CAUTION
RISK OF INJURY luminaire servicing maintenance.
Avoid while
direct it is
on.
eye
or performing exposure
from to
carton, the
light
source
CAUTION
RISK OF FIRE
9 Keep combustible and other materials that can burn away from lamp/lens.
9 Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.
CAUTION
RISK OF PRODUCT DAMAGE
9 Never connect components under load.
9 Do not mount or support these luminaires in a manner that can cut the outer jacket or damage wire insulation.
9 Unless individual product specifications deem otherwise: Never connect an LED product directly to a dimmer packs, occupancy sensors, timing devices, or other related control devices.
LED luminaires must be powered directly off a switched circuit.
9 Unless individual product specifications deem otherwise: Do not restrict luminaire ventilation.
Allow for some volume of airspace around luminaire.
Avoid covering LED luminaires with insulation, foam or other material that will prevent convection or conduction cooling.
9 Unless individual product specifications deem otherwise: Do not exceed luminaire’s maximum ambient temperature.
9 Only use luminaire in its intended location.
9 LED products are polarity sensitive.
Ensure proper polarity before installation.
9 Electrostatic Discharge (ESD): ESD can damage LED fixtures.
Personal grounding equipment must be worn during all installation or servicing of the unit.
9 Do not touch individual electrical components as this can cause ESD, shorten lamp life or alter performance.
9 Some components inside the luminaire may not be serviceable.
In the unlikely event your unit may require service, stop using the unit immediately and contact a Peerless Lighting representative for assistance.
9 Always read the fixtures complete installation instructions prior to installation for any additional luminaire specific warnings.
Please see product specific installation instructions for additional warnings or any applicable FCC or other regulatory statements.
Failure to follow any of these instructions could void product warranties.
For a complete listing of product Terms and Conditions, please visit www.PeerlessLighting.com.
Peerless Lighting, an Acuity Brands Company, assumes no responsibility for claims arising out of improper or careless installation or handling of its products .
Part Number: PIN004102 Description: “INSTR, IMPORTANT SAFETY LED” Revision: C Effective Date: 07/2012 ECO3665 Page 2 of 2
PIN005801 Rev. B 01/13/2015 ECO3758 OR3W1
These installation instructions are used for installing the following luminaires and kits:
Mounting Kit (Accessories)
Luminaire
OR3W1
Used On
Feed and Support locations OR3WFK/SK
Adjustable Cable
WARNING: Please read the “important safety instructions” prior to installation of this product.
A) Identification of OR3W1 Luminaire Sections...………………………………………………………….…... Page 1
B) Arm Mounting Luminaire Row Installation…………………………………………………………………. Page 1-2
A) Identification of Luminaire
3
1
4
"
2X4 SWITCH BOX
BY OTHERS
1 7
8
"
4"
WALL MOUNTING BRACKET
5
8
"
7 7
8
"
Optional DU
(Dust Cover)
2
1
8
"
3
3
4
"
1
PIN005801 Rev. B 01/13/2015 ECO3758
B) Arm Mounting Luminaire Row Installation
1 2 3
PIN000000 Rev. X 00/00/00 ECO0000
OR3W1
XXX
Using a laser or snap line, mark wall for center line. Use Support Spacing diagram to determine locations of power feed and supports. Cut wall material for 2"x4" switch box at feed location. Pull building wires through and attach wall bracket to box with screws provided from the box.
Install all support brackets noted in the
Support Spacing diagram for entire run.
Be sure wall is properly reinforced at all supports.
Attach (2x) arm mounting kits by screwing in the stem all to way into the luminaire until it stops. Align the mounting plate to vertical position then tighten the nuts. Raise the Starter luminaire into position. Connect building wires with fixture wires using appropriate twist-on connectors. Gently place wire connection back into switch box.
Hang the luminaire onto the wall- mounting brackets. Secure using the (2)
#8-32-1/4” setscrews provided. If applicable, go to Step 4 for joining row or skip to Step 5 to complete row.
4 5
Raise the Joiner or Ender luminaire into position and connect wire harnesses.
Secure luminaire to each support bracket and join with (2) #8-32x1/4” pan head screws provided.
Repeat Step 1 through 4 as needed.
Adjust and level the luminaire where necessary. Secure canopies using the (4)
#8-32-1/2” setscrews provided.
2