® For Your Information... EcoSystem® Ballasts and Emergency Wiring APPLICATION NOTE #140 Overview EcoSystem Lighting Networks are easily used with Emergency (essential) lighting systems. EcoSystem ballasts may be used for Emergency and egress lighting. EcoSystem ballasts used for Emergency lighting must be separated physically and electrically from utility (normal/ non-emergency) power devices; however, the EcoSystem Bus may be wired to both normal/ non-emergency fixtures and Emergency fixtures as well. This application note details emergency fixture wiring for EcoSystem ballasts. For information on using emergency ballasts and dimming ballasts see Lutron Application Note #50. Wiring Details: EcoSystem Bus wired NEC® Class 2 Use the following wiring guide when the EcoSystem Bus wires (E1 & E2) are wired according to NEC® Class 2 wiring codes. Wiring to EcoSystem Ballasts in Emergency and Normal Fixtures (EcoSystem Bus NEC® Class 2) NEU Emergency Feed (from transfer switch) HOT Conduit EcoSystem Ballast E1 E2 Emergency Fixture Utility Power (normal/nonemergency) NEU HOT Conduit EcoSystem Ballast E1 E2 Normal Fixture EcoSystem Bus (to additional ballasts and Bus Supply) Need additional assistance? Call the Lutron Technical Support Center 1-800-523-9466. Please provide exact model number when calling. 1 Wiring Details: EcoSystem® Bus Wired NEC® Class 1 Use the following wiring guide when the EcoSystem Bus (E1 & E2) wires are wired according follow NEC® Class 1 wiring codes. Wiring to EcoSystem Ballasts in Emergency and Normal Fixtures (EcoSystem Bus NEC® Class 1) Emergency Feed (from transfer switch) NEU HOT Conduit EcoSystem Ballast E1 E2 Emergency Fixture Conduit Utility Power (normal/nonemergency) EcoSystem Bus (to additional ballasts and Bus Supply) NEU HOT Conduit EcoSystem Ballast E1 E2 Normal Fixture Additional Information During normal operation (utility power is present), all EcoSystem ballasts will operate as programmed. When utility power fails, the EcoSystem ballast, powered with an Emergency feed, will turn on to its programmed Emergency light level (100% by default) and ignore all other inputs. Notes • In all examples shown, the EcoSystem Bus Supply or EcoSystem Energi Savr NodeTM unit must be powered via normal/non-emergency power ONLY. • When using a ballast module (ie: C5-BMF-2A), wire the device like the EcoSystem ballasts shown. The ballast module will power the ballast(s) to which it is wired in an emergency condition. • Emergency lighting codes vary by locale and may require more stringent separation of normal and essential lighting circuits. Always consult local code prior to completing an EcoSystem installation. Need additional assistance? Call the Lutron Technical Support Center 1-800-523-9466. Please provide exact model number when calling. 2 UL924 Compliance with EcoSystem® Using a LUT-ELI-3PH with a EcoSystem Bus Supply or EcoSystem Energi Savr NodeTM unit ensures that the system is compliant with UL924. Follow the wiring diagram in the LUT-ELI3PH for mains wiring. Use the diagram below to complete the installation. There can be up to 20 Bus Supplies or 32 or EcoSystem Energi Savr Node units connected to one LUT-ELI-3PH. Example 1: LUT-ELI-3PH with EcoSystem Bus Supply LUT-ELI-3PH 24 VCommon PP-120-H or PP-277-H Power Pack t Ho 100-347 V~ 50/60 Hz 3 Phase Normal Supply Neutral 11 10 9 8 7 6 5 4 CLASS 2 LOW VO LTAGE WIRING 3 2 mo Com ) (Pin 5 12 From Normal/ Emergency Supply 1 24 V- n Common . e rg Em nse S e n 6) (Pi Su Bus pp ly Su Bus pp ly 120-277 V~ Normal/ Emergency Supply Connect up to 20 Bus Supplies Wiring Summary: • Wire Power Pack Red Wire (+24 V-) to LUT-ELI-3PH terminal 8 (V+) • Wire Power Pack Black Wire (Common) to LUT-ELI-3PH terminal 7 (Circuit Common) and to EcoSystem Bus Supply Terminal 5 (Common) • Wire Signal wire from LUT-ELI-3PH (terminal 1) to EcoSystem Bus Supply terminal 6 (CCI-Emergency) Note: When normal power fails and the LUT-ELI trips, the EcoSystem Bus Supply stops powering the EcoSystem bus, and all emergency ballasts will turn on to their emergency light level. Note: The LUT-ELI-3PH includes panic closure inputs as well. Consult the LUT-ELI-3PH instructions for wiring details. Need additional assistance? Call the Lutron Technical Support Center 1-800-523-9466. Please provide exact model number when calling. 3 UL924 Compliance with EcoSystem® Example 2: LUT-ELI-3PH with EcoSystem Energi Savr NodeTM Unit 120-277 V~ Normal/Emergency Feed H N EcoSystem Energi Savr Node G ECO2 ECO1 RESET PP-120-H or PP-277-H Power Pack ECO1 ECO1 PWR TEST From Normal/ Emergency Supply CCI COM IR 4 COM COM GROUP 4 EMERG +20V OCC 4 COM GROUP 3 PHOTO 4 PHOTO 3 IR 3 IR 2 COM GROUP 2 +20V OCC 3 IR 1 +20V OCC 2 COM GROUP 1 PHOTO 2 MUX PHOTO 1 QS LINK OCC 1 MUX +24V +20V COM TEST TEMP CONTACT CLOSURE ETHERNET Hot 24 VCommon Neutral Power Pack COM COM EMERG CCI 120-277 V~ Normal Supply 5 4 3 LED2 LED1 LED3 1 TEST RADIOTOUCH 6 FACF NOT USED 2 GND PHASE 7 ´FACP´ N/O 8 CONTACTS 9 ´FACP´ N/C 10 COMMON MUX 11 +24VFW DRAIN 12 CONTACTS SENSE Com – Common MUX CONTACT CLOSURE S1 CLASS 2 LOW VOLTAGE WIRING LUT-ELI-3PH Emerg – Emergency Wiring Summary: • Wire Power Pack Red Wire (+24 V-) to LUT-ELI-3PH terminal 8 (V+) • Wire Power Pack Black Wire (Common) to LUT-ELI-3PH terminal 7 (Circuit Common) • Wire Signal wire from LUT-ELI-3PH (terminal 1) to Energi Savr Node Emerg input Note: When normal power fails and the LUT-ELI trips, the EcoSystem Energi Savr Node stops powering the EcoSystem bus, and all emergency ballasts will turn on to their emergency light level. Note: The LUT-ELI-3PH includes panic closure inputs as well. Consult the LUT-ELI-3PH instructions for wiring details. Need additional assistance? Call the Lutron Technical Support Center 1-800-523-9466. Please provide exact model number when calling. 4 UL924 Compliance with Quantum® Using a LUT-ELI-3PH with a Quantum Bus Supply ensures that the system is compliant with UL924. Follow the wiring diagram in the LUT-ELI-3PH for mains wiring. Use the diagram below to complete the installation. Only 1 Bus Supply per hub needs to be connected per LUT-ELI-3PH. There can be up to 5 Quantum hubs connected to one LUT-ELI-3PH. Wiring to Quantum Bus Supply From Normal/ Emergency supply 24 V- Hot 120-277 V~ Normal/ Emergency Feed Common Neutral 100-277 V~ Normal supply PP-120-H or PP-277-H Power Pack 78 56 34 12 Common 5 4 3 LED2 LED1 1 LED3 2 TEST RADIOTOUCH 6 FACF NOT USED ´FACP´ N/O 7 CONTACTS 8 GND PHASE 9 ´FACP´ N/C 10 CONTACTS 11 COMMON 12 +24VFW EM C MUX E2 MUX E1 DRAIN E2 SENSE E1 S1 CLASS 2 LOW VOLTAGE WIRING Emerg. signal LUT-ELI-3PH Wiring Summary: • Wire Power Pack Red Wire (+24 V-) to LUT-ELI-3PH terminal 8 (V+) • Wire Power Pack Black Wire (Common) to LUT-ELI-3PH terminal 7 (Circuit Common) and to Quantum Bus Supply Terminal 5 (Common) • Wire Signal wire from LUT-ELI-3PH (terminal 1) to Quantum Bus Supply terminal 6 (CCI-Emergency) Note: When normal power fails and the LUT-ELI-3PH trips, the Quantum Bus Supply stops powering the EcoSystem bus, and all emergency ballasts will turn on to their emergency light level. Note: The LUT-ELI-3PH includes panic closure inputs as well. Consult the LUT-ELI-3PH instructions for wiring details. Need additional assistance? Call the Lutron Technical Support Center 1-800-523-9466. Please provide exact model number when calling. 5 Notes Contact Information ASIAN HEADQUARTERS Singapore Lutron GL Ltd. 15 Hoe Chiang Road, #07-03 Euro Asia Centre Singapore 089316 TEL +65.6220.4666 FAX +65.6220.4333 Internet: www.lutron.com E-mail: product@lutron.com WORLD HEADQUARTERS USA Lutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299 TEL +1.610.282.3800 FAX +1.610.282.1243 Toll-Free 1.888.LUTRON1 Technical Support 1.800.523.9466 Asia Technical Hotlines Northern China: 10.800.712.1536 Southern China: 10.800.120.1536 Hong Kong: 800.901.849 Indonesia: 001.803.011.3994 Japan: +81.3.5575.8411 Macau: 0800.401 Singapore: 800.120.4491 Taiwan: 00.801.137.737 Thailand: 001.800.120.665853 Other countries: +65.6220.4666 North and South America Technical Hotlines USA, Canada, Caribbean: 1.800.523.9466 Mexico: +1.888.235.2910 Central/South America: +1.610.282.6701 EUROPEAN HEADQUARTERS United Kingdom Lutron EA Ltd. 6 Sovereign Close, London, E1W 3JF United Kingdom TEL +44.(0)20.7702.0657 FAX +44.(0)20.7480.6899 FREEPHONE (UK) 0800.282.107 Technical support +44.(0)20.7680.4481 Printed in U.S.A. 02/2011 P/N 048-140 Rev. E Need additional assistance? Call the Lutron Technical Support Center 1-800-523-9466. Please provide exact model number when calling. 6