HEARTH PRODUCTS
KITS AND ACCESSORIES
775,195M
Rev. NC, 06/2006
REPLACEMENT HINGE PIN KIT
INSTALLATION INSTRUCTIONS FOR REPLACEMENT HINGE PIN KIT (CAT. NO. H5065)
FOR USE WITH MODELS T150C, TP340, TP440 AND TG440 FREESTANDING STOVES
KIT CONTENTS:
TOOLS NEEDED:
1 ea. Hinge Pin, T153
1 ea. Nut
1 ea. Washer
1 ea. Instruction Sheet
• 9/16" End Wrench
• Tap, 5/16-18 UNC (T-handle or Tap Wrench)*
• Drill Bit, 1/4” (.250") or size G (.261")*
* Only required if original
hinge pin is P/N T151.
GENERAL INFORMATION
The hinge pin in this kit replaces the original hinge pin on the stove.
WARNING
INSTALL ONLY WHEN STOVE IS COLD!
INSTALLATION INSTRUCTIONS
Identify the original hinge pin that is being replaced per Figure 1. If
original hinge pin is P/N T151 follow "A" instructions. If original hinge
pin is P/N T153, follow "B" instructions.
P/N T151
P/N T153
4. Tap the reamed out hinge hole using a 5/16-18 UNC tap.
5. Install the new hinge pin as shown in Figure 2. DO NOT OVERTIGHTEN IT! READ "IMPORTANT NOTE *" ON THIS PAGE.
6. Reinstall door (align hinge holes in doorframe with hinge pins).
Ensure that the lower hinge hole of doorframe is fully seated
onto the shoulder of the hinge pin.
B. Replacing P/N T153 Hinge Pin.
1. Remove door from stove, if necessary (open door, then lift
up and off).
2. Remove the nut and washer from original hinge pin by unscrewing it from inside the firebox (see Figure 2). Remove the
original hinge pin by unscrewing it from the front (or unscrew
it from inside the firebox if the hinge pin is broken).
3. Install the new hinge pin as shown in Figure 2. DO NOT OVERTIGHTEN IT! READ "IMPORTANT NOTE *" ON THIS PAGE.
4. Reinstall door (align hinge holes in doorframe with hinge pins).
Ensure that the lower hinge hole on doorframe is fully seated
onto the shoulder of the hinge pin.
CAUTION: When opening the door in the future, do not extend it
beyond its normal travel. Overextending the door opening range
can put excessive stress on the hinge pins and doorfame which may
result in breakage.
Inside Wall of Stove
T153 Hinge Pin
Nut
5/16"
1/4"
Outside Face of Stove
Washer
• If the thread diameter is 1/4", hinge pin is P/N T151.
• If thread diameter is 5/16", hinge pin is P/N T153.
Figure 2 - Hinge Pin Installed
Figure 1 - Identify The Original Hinge Pin
A. Replacing P/N T151 hinge pin with P/N T153.
1. Remove door from stove, if necessary (open door, then lift up
and off).
2. Remove the nut and washer from original hinge pin by unscrewing it from inside the firebox (see Figure 2). Remove the
original hinge pin by unscrewing it from the front of the stove (or
unscrew it from inside the firebox if the hinge pin is broken).
3. Enlarge the existing hinge pin hole on the stove face by reaming
the hole using a size G drill bit (.261"), or a 1/4” drill bit (.250").
*IMPORTANT NOTE
When installing the new hinge pin, do not overtighten
it. After threading it in, if it seats before reaching the
12 o’clock position (pin pointing up), do not force it
to that position. Instead, rotate it counterclockwise
until it reaches the 12 o’clock position, then install
washer and nut per these instructions.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
LHP reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and the discontinuance of colors, styles and products. Consult your local
distributor for fireplace code information.
LHP
Printed in U.S.A. © 2006 by LHP
P/N 775,195M REV. NC 06/2006
NOTE: DIAGRAMS &Page
ILLUSTRATIONS
1 of 1 NOT TO SCALE.
1110 West Taft Avenue
Orange, CA 92865