THREE-MR-AA THREE-MR-MH-AA installation instructions mounting bars Three kinds of mounting bars may be purchased as accessories from Edison Price Lighting. Standard mounting bars are 27” long, 3/4” high C channels for use in suspended ceiling systems. Residential mounting bars are 18” and 26” long telescoping bars for use in wood joist construction. Caddy #517A bars are 26” long telescoping bars which attach easily to many kinds of suspended T-bar. lamping • Remove lamp holder from housing by curling finger around edge of the lamp holder stand and pulling lamp holder out of its mounting slot (see reverse side for illustration). socket clasp • Withdraw socket from housing. lamp holder • Attach lamp to socket. tab • Slide lamp into lamp holder clasp. MR16 lamp • Insert tab of lamp holder into slot above one of two rotation guides. lamp holder lens lens spring lamp holder stand slot lamp holder aperture rotation guide Note: A Solite prismatic lens is included with THREE-MR-AA only. installation This fixture is listed, suitable for use in a fire rated ceiling, and should be installed in accordance with the National Electrical Code and local regulations. height adjustment plate (wing nut inside housing) •Insert mounting bars through to the adjustable mounting brackets on either side of the fixture. wing nut adjustable mounting bracket This fixture can be attached to ceiling runners which are positioned no less than 1” and no more than 3 7/16” above the finished ceiling surface. •Position the fixture so that its mounting bars lie on top of the ceiling runners. junction box •When the fixture is correctly located, fasten the mounting bars securely to the ceiling runners. •Adjust the fixture to the proper height by loosening the wing nuts on both adjustable brackets and setting the fixture so that the bottom edge of the circular plaster ring will be flush with the surface of the finished ceiling. Tighten the wing nuts. wing nut WARNING: Do not install ceiling insulation within 3 inches of fixture sides nor above fixture in such a way to entrap heat. lamp holder stand •Wire the fixture following the instructions on the reverse. After all ceiling installation and finishing work is complete, install reflector. •Line up reflector side notch with lamp holder stand. rotation guide • Push reflector, slowly and evenly, into fixture. reflector see reverse side for LightPlate Edison Price Lighting 41-50 22nd Street Long Island City, NY 11101 www.epl.com © side notch 601359-00 If reflector does not fit correctly because plaster ring is not flush with finished ceiling as shown, housing may be lowered in height. • Locate two wing nuts on opposing inside walls of housing. • Loosen nuts; pull housing down until plaster ring is flush. • Tighten wing nuts. wiring This fixture is listed and approved for ten #12 wire 90°C branch circuit pull-through wiring. 120-volt service shown •Remove the outer cover of the junction box by releasing the spring clip on the top of the box. •Splice the incoming black wire to the black lead. •Splice the incoming white wire to the set of white leads. •Splice the incoming green ground wire to the bare copper wire attached to the inside of the junction box. •Do not disturb the blue lead splice. •Put wire nuts on all open splices. •Snap junction box cover back into place. adjustment • Rotation: Unlock rotation by placing a fingertip on top of rotation lock lever and pulling in toward center of fixture aperture. Adjust rotation by grasping lamp holder assembly and pushing it gently around aperture. Lock rotation by pushing rotation lock lever back into original position. • Tilt: Unlock tilt by loosening wing nut on lamp holder arm. Adjust tilt by grasping lamp holder assembly and tilting it as required. Note the angle marks: each mark equals 10° tilt. Lock tilt by tightening wing nut. rotation lock lever lamp holder assembly wing nut lamp holder arm unlocked position angle marks locked position rotation lock lever LightPlates A LightPlate decorative trim may be used instead of a reflector. LightPlates are installed in the same way as a reflector (see reverse side). servicing To gain access to the transformer or ballast through the fixture aperture: •Remove the reflector by pulling straight down. •Remove the lamp holder by curling a finger around the edge of the lamp holder stand and pulling lamp holder out of its mounting slot. •Slide lamp out of lamp holder and detach from socket. Save lamp and lamp holder. •Remove the wing nut from the transformer/ballast mounting plate and pull the plate into housing. •Angle the transformer/ballast out of housing aperture. driver mounting plate housing aperture light engine bracket wing nut driver reflector maintenance The reflector may be cleaned of dust with a damp, soft lint-free cloth. To remove fingerprints or dirt, wash with a solution of dishwashing detergent and water, rinse, and dry with a soft lint-free cloth. Avoid wiping when reflector surface is dry.