PROJECT INFORMATION
HERCULUX™
Job Name
H99 SERIES – 5 DAY SHIP PROGRAM
Fixture Type
Catalog Number
Approved by
PRODUCT FEATURES:
»»Surface mount – wall (H99ED), ceiling or wall (H99FD);
nominal 9"W×9"L×7"D
»»Heavy duty die-cast aluminum housing
»»UV-stabilized, injection molded polycarbonate lens
»»Peace of Mind Guarantee® against breakage
H99ED
H99FD
SPECIFICATIONS
HOUSING: One-piece heavy duty die-cast, low-copper aluminum housing. Housing flange interlocks around refractor producing maximum moisture deflection and resistance to prying. Housing
provided with four standoff mounting holes. One 3/4" IPS tapped hole on back of housing. Standard housing in dark bronze TGIC polyester powder coat – 5-stage pre-treatment.
H99ED: Two 3/4" IPS tapped and plugged holes on top and bottom of housing – see Cross Section/Details. H99FD: Two 3/4" IPS tapped and plugged holes on sides of housing –
see Cross Section/Details.
REFLECTOR: High efficiency textured aluminum.
LENS: One-piece internal-prismatic refractor (UV-stabilized, high impact, virgin injection molded polycarbonate). Nominal thickness .125". H99ED: Eyelid: High-impact resistant, UV-stabilized,
injection molded opaque dark bronze polycarbonate. Optional finishes to match housing. Nominal thickness .125".
GASKET: Die-cut closed cell neoprene gasket seals die-cast housing to mounting surface. Refractor inset into housing and sealed to integral ledge with one “O” ring closed cell
silicone gasket.
HARDWARE: Four captive stainless steel Torx® with center pin fasteners secure refractor/eyelid to housing. Shoulder fastener design and washer prevent refractor/eyelid stress due to over torquing.
ELECTRICAL: Electronic and magnetic ballasts high power factor standard. Shock absorbing, medium base lamp socket provided for HID lamps. See Lamp Type for electronic metal halide
ballast option.
INSTALLATION: Standard fixture must be installed lamp base up. Standard four-point mounting required for Peace of Mind Guarantee®.
LISTINGS: UL and CUL listed for Wet Location.
5
Day
ORDERING INFORMATION (Ex: H99ED-C-DB-50S-1-120-FS)
Model
Lens Type
Finish
C
Model
H99ED Eyelid (wall mount only)
H99FD Full Face
Lens Type
C
Clear Prismatic Polycarbonate
Finish
DB Dark Bronze
Lamp Type
Lamp Qty
Voltage
Options
Accessories
DB
Lamp Type (Qty/Ballast/Volt./Starting Temp)
26Q 26 Watt Quad (1/RS/120,277,DV,347/0°F)
26P 26 Watt PLT (1/RS/120,277,DV,347/0°F)
32P 32 Watt PLT (1/RS/120,277,DV,347/0°F)
42P 42 Watt PLT (1/RS/120,277,DV,347/0°F)
50M† 50 Watt MH (1/HPF/120,277,DT/-20°F)
50S 50 Watt HPS (1/HPF/120,277,DT/-40°F)
70M† 70 Watt MH (1/HPF/120,277,DT,347/-20°F)
70ME† 70 Watt MH (1/EB/120,277,347/-20°F)
70S 70 Watt HPS (1/HPF/120,277,DT,347/-40°F)
Lamp Quantity
1
One Lamp
Options
BPC Photo Control - Button Type (120/277V only)
EL Standard Lumen EL Pack (120/277V CFL only, 32 system watt max.)
FS Single Fuse & Holder
Accessory
9500Torx® Screwdriver
† UV shielding lamp supplied
s
n/a with BPC
Voltage
120 120 Volts
277 277 Volts
347s 347 Volts
DVs 120-277 Volts, electronic ballasts only
DTs 120/277 Volts, HID magnetic ballasts only
www.kenall.com
P: 800-4-Kenall
F: 847-360-1781
1020 Lakeside Drive Gurnee, Illinois 60031
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers,
and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof.
Content of specification sheets is subject to change; please consult www.kenall.com for current product details. © 2014 Kenall Mfg. Co. All rights reserved.
H99_ED_FD-QS_5DAY-110713
For additional photometry, go to www.kenall.com
HERCULUX™
H99 SERIES – 5-DAY SHIP PROGRAM
DIMENSIONAL DATA
CROSS SECTION / DETAILS
BACK MOUNTING VIEW
6.44"
9.00"
9.00"
9.00"
7.11"
7.28"
H99ED
www.kenall.com
H99FD
P: 800-4-Kenall
5.38"
(1) 3/4" IPS
(4) .28" Dia.
Mounting K.O. (2) 3/4" IPS Tapped Hole
Tapped &
Plugged Holes
F: 847-360-1781
(4) .31" Dia. Holes
6"
(3) 3/4" IPS Tapped
& Plugged Holes
2.31"
1020 Lakeside Drive Gurnee, Illinois 60031
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers,
and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof.
Content of specification sheets is subject to change; please consult www.kenall.com for current product details. © 2014 Kenall Mfg. Co. All rights reserved.
H99_ED_FD-QS_5DAY-110713